Search Documents

By Claude Bazin

The Quebec province in Canada is a major producer of aluminium through electrolysis of alumina. The alumina that feeds the electrolysis cells is mainly imported from foreign countries, where it is extracted from bauxite. Other alumina sources, such as clays, have sometimes been considered as potential substitutes for bauxite. There is a large clay deposit in the area of Murdochville in Quebec, with sulfuric acid and electricity available nearby the orebody, as well as sea port facilities leading to the major aluminium plants in Quebec. These are favorable factors to assess the economics of an industrial plant to produce alumina from clays. This paper reviews some of the processes considered for the extraction of alumina from clays and presents results of the initial work carried out on the clay available from Murdochville.

May 1, 2001

By R. J. Hafsten, E. S. Davenport, R. A. Grange

The influence of austenite grain size upon the hardenability of steel is now fairly well understood; for a given austenite, increasing the grain size increases the depth of hardening, and, since the latter is related to the fundamental transformation behavior of austenite, it follows that austenite decomposition must, in general, be retarded by increasing grain size. To date, very little quantitative information bearing directly on the effect of austenite grain size upon the progress and result of isothermal transformation has been published. Davenport and Bain,' and Zimmerman, Aborn and Bain2 have shown that the transformation is definitely relarded in hypereutectoid plain carbon steels at temperatures near and above the upper region of rapid transformation (Ar') when the austenite grains are increased in size. More recently, Griffiths. Pfeil and Allen3 investigated the effect of a series of different heating (austenitizing) temperatures upon the progress of isothermal transformation at 1245°F. (675°C.) and 745ºF. (395°C.) in a medium carbon, low-alloy steel; while they reported no measurements of the austenite grain size, their results suggest that increase in grain size retards austenite transformation at 1245ºF. (675°C), but has no appreciable effect at 745°F (395°C.). The present paper deals with the results of a study of the isothermal transformation of austenite in a single commercial alloy steel in which a fine-grained or a coarsegrained state was induced by appropriate selection of austenitizing temperature. The data are presented in the form of isothermal transformation diagrams, which clearly show that coarsening the grains lessens the rate of transformation of austenite to proeutectoid ferrite and pearlite—that is, at temperature levels above about 1000°F. (540°C.)—but is without significant effect at lower temperatures where the transformation product is bainite or martensite. It is to he presumed that the foregoing statement would be valid, at least in principle, for many other grades of steel; it confirms again that the mechanism of transformation to a pearlitic structure is fundamentally different from that to an acicular structure. A number of related observations were made, which seem to throw some light on the transformation process as it takes place in alloy steels, particularly at temperature levels in the vicinity of 1000ºF. (540°C.), where the transition from lamellar to acicular structures occurs. These data are discussed briefly in the belief that they may lead to a clearer understanding of this aspect of the subject. Material and Experimental Procedure The material investigated was a cornmercial grade of S.A.E. 4140 steel, the composition of which was as follows: 0.37 per cent C, 0.77 per cent Mn, 0.98 per cent Cr and 0.21 per cent Mo. It was hot-rolled to a 1 1/8-in. round bar and normalized by air-cooling from 1800°F. (980°C.).

Jan 1, 1941

By Robert R. Perron

The U.S. Bureau of Mines is engaged in many diverse programs for improving mine safety. Of particular interest to the Bureau are new and improved means for minimizing the hazard of fire which can be initiated by prolonged low energy electrical faults on trolley line systems. When a high energy fault occurs on a trolley line, wherein the current exceeds the magnitude normally drawn by legitimate loads, such as locomotives, then the circuit breakers at close-by power rectifier sets trip. Tripping of the breakers not only protects the equipment at the rectifier sets, but also disconnects the energy source from the fault and thereby minimizes the fire risk. However, the fault current is frequently of a level substantially below that required to trip the overload breakers. When the fault is a substantial percentage of the set level of the breakers, the energy dissipated by the fault is frequently sufficient to clear the system by rapidly burning itself clear. Such a fault is often short-lived and does not present as serious a fire risk hazard as a prolonged, much lower energy fault, wherein the energy level is too low to clear the system. The breakdown of a trolley line insulator, in which there was a 20 or 30 ampere leak, would represent such a fault or illegitimate load and a substantial fire risk.

Jan 1, 1974

By Aaron Jones, Guy Reed, Russell Frith

"In 2017, one of the international authorities on coal bursts, Dr. Chris Mark, published a paper entitled “Coal Bursts that Occur during Development: A Rock Mechanics Enigma,” in which several relevant technical issues were identified, the most pertinent being:i.whilst development coal bursts are commonly associated with geological faults, understanding which specific faults result in burst-prone development mining conditions and why, remains undefined.ii.conventional wisdom in relation to strong roof and floor geology of the coal seam might be limiting, based on certain burst examples in Colorado.iii. development coal bursts can occur without the local ground stresses being substantially elevated from their in situ levels.This paper outlines what is considered to be a credible, first-principles, mechanistic explanation for these three current development coal burst conundrums by reference to early published coal testing work examining the significance of a lack of “constraint” to coal stability and an understanding of how very specific structural geology and other geological features can logically cause this to occur in situ, albeit on a statistically very rare basis. This basic model is examined by reference to published information pertaining to the development coal-burst that occurred at the Austar Coal Mine in New South Wales, Australia, in 2014 and from the Sunnyside District in Utah, USA.The “cause and effect” model for development coal bursts presented also offers a meaningful explanation for the statistical improbability for what are nonetheless potentially highly-destructive events, being able to explain the statistical rarity being just as important to the credibility of the model as explaining the local conditions associated with burst events.The model could also form the basis for a robust, risk-based approach utilising a “hierarchy of controls” to the operational management of the development coal burst threat. Specifically, these include the use of pre-mining predictions for likely burst-prone and non-burst-prone areas, the use of the mine layout to avoid or at least minimise mining within burst-prone areas if appropriate, and finally the development of an operational Trigger Action Response Plan that reduces the likelihood of inadvertent roadway development into a burst-prone area without suitable safety controls already being in place."

Jan 1, 2019

By Smith DM Jr

Silver deposits, in which silver forms at least fifty percent of the value of the ore, are abundant and large on the east side of the Pacific and are absent in the western Pacific. To determine if this uneven distribution is related to features of consuming plate tectonic boundaries which dominate the metallogeny of the Pacific Rim, the variation of Ag/Au in porphyry copper deposits was used to estimate the relative silver content of magma generated in subduction zones. Porphyry copper provinces with high Ag/Au occur in regions of the eastern Pacific where silver deposits are abundant, suggesting that the distribution of silver deposits is controlled by the relative abun- dance of silver in subducted ocean crust. Ocean crust being subducted in the eastern Pacific is mostly less than 50 million years old in contrast to most ocean crust in the western Pacific which is much older. Enrich- ment of silver in young ocean crust at spread- ing centers may reflect metallogenetic evolution over geologic time. Silver may be transported to the surface in volcanic rocks, and deposits are common where felsic varieties are abundant. The high ,solubility of silver in natural waters provides a natural storage mechanism for silver weath- ered from these rocks and ultimately circulated in near-surface hydrothermal systems where many silver deposits form. The regional distribution of silver deposits is not influenced by discoverability, vertical metal zoning, or regional tectonic style. The effect of igneous differentiation is unclear.

Jan 1, 1987

By R. J. Sweigard

Deep tillage is used widely as a Means of alleviating excessive soil compaction. There has been some concern that the voids created by deep tillage may collapse before a more natural soil structure develops, resulting in recompaction subsequent to deep tillage. A laboratory investigation was conducted to determine the feasibility of pneumatically injecting organic material into the voids during deep tillage to prevent any significant recompaction from occurring. Various amendments were injected into the soil in the laboratory using a small-scale ripping and injection system. Measurements were made of selected soil properties to evaluate the feasibility of this method.

Jan 1, 1993

By C. F. de Mendonca, T. Kater, R. P. de Souza

Since 1976, Cia Vale do Rio Doce (CVRD) has carried out tests to develop a type of pellet made with an organic binder. Peridur is one binder that showed it could be used in industrial plants. Extensive tests were run in CVRD's pilot plant. The results are presented in this paper. The decision was made to carry out an industrial production of 50 ht (55,000 st) of pellets. The results are shown in this paper. No detrimental effects of the Peridur were observed in either the process or in product quality.

Jan 1, 1985

By A. V. Tarasov

Based on the data available in the literature and the practical experience of new metallurgical plants, a method has been proposed and relevant studies conducted for metallurgical processing of zinc sulfide concentrates. Process conditions and parameters have been identified, which ensure high levels of recovery of zinc into solution. This is achieved by leaching concentrates under the normal pressure at a temperature of >90°C in the presence of ferric iron ions. Sulfide sulfur is converted to elemental sulfur in this process. To produce elemental sulfur it is necessary to maintain oxidizing conditions in the system, characterized by a positive Eh value. In order to eliminate the interfering effect of elemental sulfur formed in the process, it is possible to add surfactants into the concentrate pulp. The proposed technology has certain advantages as compared with the high-temperature pressure leaching and is considered as a basic technology to be applied to increase zinc production at one of the Russian zinc plants.

Jan 1, 2006

By M. Schultz

The cost of remediation often drives the selection of the preferred remedial alternative at hazardous waste sites. The use of probabilistic cost/risk analyses can aid in predicting costs of remedial alternatives. Three types of information are discussed in performing cost/risk analyses: (1) data on the quantity of contamination versus the contaminant concentration; (2) unit costs of remediation for the remedial alternatives; and (3) risk to contaminant concentration relationships. Cost/risk evaluations are performed on a site-by-site basis, to account for combined risks of different contaminants and differences in quantity to be remediated versus contaminant concentration. The cost/risk analysis produces a graph of risk versus cost for each of the remedial alternatives. These costs are then compared to facilitate selection of a preferred alternative. An example of comparison of alternatives is illustrated for a historic coal gasification site.

Jan 1, 1992

By G. C. Li

Gold extraction using iodide leaching from refractory carbonaceous gold ores was studied. Thermodynamic analysis of iodide leaching chemistry had been carried out. Eh-pH diagram of Au-I2-I--H2O leaching system showed that the coordinating active forms from iodides were I3- and I-, while the major coordinate compound formed during iodide leaching was AuI-. For leaching parameters optimization, technological parameters such as I2 concentration, I2 :I- ratio, oxidation assisting agents, liquid/solid ratio, and leaching duration were studied. The leaching results showed that the average Au leaching rate reached 91% and 92% for oxidized ore and roasted primary ore respectively. Leaching process proceeded in weekly acidic or neutral slurry at ambient temperature; the leaching duration was 4 hours. After that gold was extracted from the pregnant liquor by activated carbon adsorption ? desorption ? electrowinning process. Gold recovery was over 93% in the adsorption process, while the gold recovery in electrowinning process was about 95%, provided that the initial gold concentration is 40mg/L or larger. For iodine regeneration it is enough to add hydrogen peroxide in excess into the filtrate after gold electrowinning, all the iodides existing in the solution in any forms would be precipitated in the form of elemental iodine.

Jan 1, 2014

By Michel Lefebvre, André Piché

Every organization performing R&D is faced with the challenge of introducing new technologies to its operations. Difficulties must be overcome if companies are to realize the benefits anticipated from such developments. This paper outlines the difficulties encountered in transferring to operations various technologies developed at the Mining and Exploration Division of the Noranda Technology Centre. The approach used in the selection of a privileged partner for the technology transfer, the criteria motivating the choice and the process followed to establish the partnership are presented.

Jan 1, 1997

By R. W. Raymond

Samson Jordan was born at Geneva, Switzerland, June 23, 1831. At the age of 20 years he entered the Ecole Centrale des Arts et Manufactures, at Paris, from which he was graduated with high honors in 1854. After some months of service with the Compagnie du Chemin de Fer du Nord, he was employed (upon the recommendation of his former instructor, Prof. Burat, who had recognized his remarkable ability) at the mines of Portes, belonging to the Société de l'Elairage au Gaz et des Hauts Fourneaux, etc., of Marseilles, and subsequently to construct the St. Louis iron blast-furnaces of that Co. After finishing this work, he remained at Marseilles as a member of the directory of the Co., particularly connected with the development of its mines. In 1862 he became the general advisory engineer of the Co., and still later (1873) its general manager (Administratet~r), a position which he retained until his death, February 24, 1900. He became subsequently Administrateur of other important French industrial enterprises, including those of the Compagnie des Naut Fourneaux, Forges et Aciéries de Denain et Anzin, and the Compagnie Banco-Belge des Mines de Somorrostro ; and he was also, at various times, President of the Société technique du Gaz, Vice-President of the Comité des Forges de France, mepber of the Council of the Société d'Encouragement pour l'Industrie nationale. In all these positions, it is the unanimous testimony of his colleagues that he was no mere ornamental figurehead, but a profoundly wise, practical and industrious laborer and adviser, both patient and keen in the mastery of details, yet at the same time competent to apprehend the wider bear-

Jan 1, 1902

By P. J. Uggowitzer, K. Steinhoff, A. Wolf

"With the increasing acceptance of the Thixoforging process in the last few years, also the technical and commercial requirements for this forming technology and its components increased. So far, a great deal of work has been done in the development of an efficient process and control design. However, less attention has been paid to the development of new specifically tailored aluminum wrought alloys for this specific manufacturing process. · In this paper a new AlMgSi-alloy (A6082), optimized for the Thixoforging process, is presented. In the first part, the technical potential of the new alloy is specified by its microstructural evolution and flow characteristics in the semi-solid state. In the second part, the mechanical properties of thixoforged components of different conventional AlMgSi-alloys a (e illustrated · and compared to the new alloy.IntroductionSemi-solid metalworking, also known as semi-solid forming, is a hybrid manufacturing method that incorporates elements of both casting and forging. The key to the process relies on the peculiar flow behavior of slurries containing non-dendritic solid, which was first studied at the MIT by Flemings et al. [i], in the early 1970s. It was discovered, that if an alloy is uniformly stirred during freezing, discrete rounded particles of solid are formed rather than the normal dendrites, and the slurry is highly fluid (-5 Pas) up at least 50% solid. In addition, these slurries posses thixotropic flow characteristics: the viscosity is dependent on sheare rate and time. The more vigorously they are stirred, the more fluid they become. However, on standing the viscosity recovers and the material stiffens (-106 Pas).The semi-solid forming process exploits this phenomenon. In a first step, the required non-dentritical- microstructure is obtained by mechanical or electromagnetic stirring during primary solidification of the alloy. The stirred slurry is generally fully solidified as a feedstock billet and - in a second process step - reheated above the solidus temperature into the semi-solid state. In this condition, the thixotropic properties permit the material to be handled by robotic devices and transferred to a die (Thixocasting) or subjected to- a forming process by means of forging (Thixoforging). Owing to the shear stress which acts on the semisolid material during forming operation, the viscosity of the material is reduced attaining so the desired fluid-like flow characteristics."

Jan 1, 2000

By J. N. Brooke

"This paper deals with the training of the mining and mineral engineer and the role that these professional people must play in their company environment, particularly in relation to management.THERE IS SOME CONCERN in the mining industry that the numbers of engineering graduates attracted to it and the academic training that these people have received is inappropriate. Evidence for this is:1. -The meetings and studies initiated by the various mining engineering societies to discuss:(a) attracting students and graduates to the industry; and (b) the appropriateness of the present academic training for the needs of the industry."

Jan 1, 1968

By K. T. Dreher, J. A. Brierley, C. L. Brierley

Water from underground uranium mines located in the Ambrosia Lake district near Grants, New Mexico, U.S.A., is treated to reduce levels of uranium, selenium, radium and molybdenum. The treatment system consists of a series of ponds and an ion exchange plant. Bacterial and algal populations present in the pond system are considered agents which actively assist in removal of the pollutants present in the water. Pondbottom sediments maintain a reducing zone and a large population of sulfate-reducing bacteria of the genera [Desulfovibrio] and [Desulfotomaculum]. Uranium, molybdenum, and selenium accumulate in the pond sediment. Stimulation of the microbial sulfate-reducing activity resulted in a decrease of soluble concentrations of these elements in laboratory systems. Predominant components of the treatment ponds’ algal flora are the filamentous [Spirogyra] and benthic [Chara]. Laboratory study indicates that [Spirogyra] is more active than [Chara] in removal of uranium and molybdenum from solution. However field-collected algal samples of both of the genera contain uranium and molybdenum. Laboratory studies indicate that death and decay of the algae in association with pond sediment does not result in return of cellbound uranium and molybdenum to the water. The algae appear to act as bio-filters for accumulation of particulate pollutants and agents for adsorption and/or absorption of soluble pollutants.

Jan 1, 1980

By Williams Morales C.

Las operaciones de Lixiviación de Minera Yanacocha se inician con la primera barra fundida el 06 de Agosto de 1993 además de la construcción del primer pad de Carachugo y sus plantas , luego en el año 1995 se construye el pad de Maqui Maqui, en el año 1998 se construye el pad de Yanacocha Norte, en el año 2001 se construye el pad La Quinua, luego en el 2012 se construye el pad La Quinua 8A-WOX.Conforme a los avances y crecimiento de las operaciones se ha implementado plantas de tratamiento de agua tanto para aguas acidas (AWTP) como agua de excesos (EWTP). En las operaciones de Lixiviación se ha desarrollado tecnología de acuerdo a la composición mineralógica y geológica de cada pad, A todos los pads se deposita mineral por carguío con mineral ROM, se aplica el riego con mangueras para celdas de áreas planas y riego por micro aspersión para taludes.

Sep 1, 2017

By Zavis M. Zavodni, Carl D. Broadbent

During the past 15 years, rock mass structural properties have become acknowledged as the focal point for rock slope design. Re- search into the methods for measuring and incorporating structure into the design effort has taken many directions and has produced a variety of useful techniques. Among the findings at Kennecott has been the realization that structure-controlled instability can be categorized as regressive or progressive depending on the relative geometries of slope and structure and on the strength characteristics of the structures. It was further identified that a failure condition can initiate as regressive and in time become progressive should external stimuli increase or structure characteristics be altered due to extensive displacements. The transition point has been shown to be a useful indicator of the expectable collapse time. This paper defines three fundamental failure types as dictated by structure and offers discussion on the practical value of such a classification to slope design and failure control. Several prominent examples of failures typifying the categories of structure- controlled instability are discussed. An application of f allure prediction based on the regressive-to-progressive transition point is described.

Jan 1, 1983

By L. W. Casteel

This is a story of progress through research, invention and innovation-progress that made a small mine in Missouri into a large and prosperous corporation. The St. Joseph Lead Co. was founded in Borne Terre, Missouri, in 1864. At that time, the mine consisted of a narrow trench eight feet deep; the mill was a hand-operated jig; and the smelter, a charcoal oven with a sloping hearth. During the first year, production was suspended for two months because of an invasion by the Confederate army. There have been few interruptions since that time.

Jan 7, 1964

By S. H. Ash

NINE-TENTHS of the total anthracite deposits of North America are in Pennsylvania. Corrosion of pumping equipment by acid mine waters has been experienced at tremendous cost by mining companies in the anthracite region of Pennsylvania, for many years in many ways. The design and specifications of the large centrifugal pumps as provided in the proposed mine-drainage system (7-35, 45, 46, 48, 54, 64, 70, 71)° make it imperative that a metal or alloy be recommended that has the highest corrosion resistance and, at the same time, acceptable properties suitable for general workability (welding and machining). This report presents data on the corrosive and erosive effects of acid mine waters in the anthracite region on metals and alloys for pumping equipment and drainage facilities necessary to remove or control this water.

Jan 1, 1955

By C. L. de Jongh

Fracturing of the rock caused considerable difficulties during the boring of a deep-level tunnel in hard rock. A pilot bore was suggested as a possible means of reducing the effect of the fracturing, and this possibility was investigated theoretically by means of a three-dimensional elastic stress analysis. Failure criteria were applied to the results of this analysis, and it was found that fractures predicted by the use of a simple criterion of limiting tensile macrostrain criterion agreed remarkably well with in situ observation. It was concluded that fracture could not be avoided and that a pilot bore was likely to aggravate tunnelling conditions.

Jan 1, 1978