Search Documents

By Wilton Johnson

Native asphalt was produced by four companies in two States, Texas and Utah. Bituminous limestone, used primarily as a paving material for street and road repair, was produced by one firm. R. L. White Co., Dabney Quarry, Uvalde County, TX. Gilsonite, a solidified hydrocarbon found only in Utah and Colorado, was mined by three firms: American Gilsonite Co., a division of Chevron Resources Co. (a subsidiary of Standard Oil Co. of California); Ziegler Chemical and Mineral Corp.; and Hydrocarbon Mining Co. (a subsidiary of Oberon Oil Inc., a Utah corporation), from properties in Uintah County, UT. Gilsonite is used for a variety of purposes including automobile bodysealer, light-weight aggregate for cement used in oil well drilling, asphaltic building board, protective coverings, anticorrosive paints, and roofing compounds. Gilsonite production in 1985 declined 57% owing primarily to reduced oil well drilling activity. The value per ton was essentially unchanged.

Jan 1, 1987

By Jozef Zmik, Sergey Dobatkin, Martin Fujda, George Raab, Libor Kraus

"The present work, likewise, deals with grain refinement of medium carbon steel AISI 1045 having different initial microstructure resulting from thermal and/or thermomechanical treatment (TM) applied prior severe plastic deformation. In case of TM treated steel, structure refinement was conducted in two steps. Preliminary structure refinement has been achieved due to multistep open die forging process which provided total strain Eef ~ 3. Uniform and fine recrystallized ferrite structure with grain size of the order of 2-5 µm and with nest-like pearlite colonies was obtained. The further grain refinement of steel samples having different initial structure was accomplished during warm Equal Channel Angular Pressing (ECAP) at 400°C. The microstructure development was analyzed in dependence of effective strain introduced ( Eef ~ 2.5 - 4). Employment of this processing route resulted in extensive deformation of ferrite grains where mixture of subgrains and ultrafine grain was found regardless the preliminary treatment of steel. As straining increases the dynamic polygonization and recrystallization became active to form mixture of polygonized subgrains and submicrocrystalline grains having high angle boundaries. The intensive straining and moderate ECAP temperature caused the partial cementite lamellae fragmentation and spheroidization as straining increased. The lamellae cementite spheroidization was more extensive in TM treated steel samples. The deformation behavior of for both steel structural state confirm the strength increase; however the work hardening behavior was modified with respect to initial structure of steel prior SPD processing.IntroductionIn the last years, ultrafine grained materials have attracted considerable research interest because they tend to possess high strength without sacrificing toughness and ductility. Microstructural refinement of steel is usually achieved by alloying and/or by thermomechanical treatment process, which modifies phase transformation. Recently, advancement of severe plastic deformation (SPD) techniques provides another efficient access for grain refinement of metals and alloys. The fabrication of bulk materials with ultrafine grain sizes has attracted a great deal of attention over the past two decades because of the materials' enhanced properties [ 1, 2]. In last decade a worldwide effort in manufacturing process to obtain ultrafine grain structures in steels is persisting."

Jan 1, 2011

By C. M. Suhr

n order to validate the borehole analysis valuation procedure commonly used in the South African gold mining industry, a simulated orebody was used to create borehole values which would serve as data for the procedure. After confirming the distribution, calculating the variance size of area relationship, estimating the block variance, and calculating a profit measurement for each set, comparisons were made to the known population parameters. Results show only one overall bias (in the estimation of the lognormal third parameter), which is carried throughout the analysis. The remainder of the analysis is unbiased, validating the procedure.

Jan 1, 1987

By G. Richard Dreese

Most coal mining states have passed or amended laws restricting strip ruining in the past two years. In light of this and in anticipation of further restrictions by the states and the federal government on strip mining this paper attempts to show the Impact of these new laws on the structure of the coal mining industry in Ohio and specifically on one small stripping firm in Ohio. The implications of the study are applicable to other states under similar circumstances and to other industries which are being caught up in the ecological-economic struggle.

Jan 1, 1973

By K. C. Grogan

"GeneralGIANT ORE is complex, with the gold values for the most part occurring in extremely close association with arsenopyrite, stibnite, jamesonite, and a wide group of antimonial minerals locally termed 'the grey minerals'. Pyrite is the most abundant of the sulphide minerals• and minor quantities of chalcopyrite, galena, and sphalerite also occur. Pyrrhotite has been found in some sections of the mine, but to date none of it has been nickeliferous. Native gold occurs in varying amounts throughout the ore bodies.In 1944, ore dressing investigations were commenced on diamond-drill core rejects and samples of surface outcrop ore. Results soon indicated that treatment to produce satisfactory recovery of the gold values would involve fine grinding to 80-85 per cent minus 200 mesh, recovery of free gold by jigs, followed by flotation, roasting of the flotation concentrate, and subsequent cyanidation of the calcine. Proceeding from this information, the flow-sheet was prepared, plant design worked out, equipment purchased, and construction of the treatment plant commenced in May, 1947.The crushing, grinding, and flotation units of the plant were rushed to completion and commenced operation on May 12th, l.948, at 225 tons of ore per day. This rate was maintained until January 27th, 1949, when the Allis-Chalmers roaster and cyanide plants were completed and commenced operation. During the period May 12th, 1948, to January 27th, 1949, gold recovered by amalgamation was the sole source of revenue. Flotation concentrate was stockpiled pending the completion of the Allis~Chalmers roaster and cyanide plants."

Jan 1, 1953

By Felicia F. Peng

In operation of column flotation of fine coal, the smaller bubbles are required to effectively recovery of fine hydrophobic particles. However, smaller size bubbles alone does not ensure an efficient flotation for fine particles. The sufficient available bubble surface area per unit column are essential for effective column flotation. The experiments are conducted in a lab-scale column using two different bubble size distributions and three different particle size distributions for flotation of Pittsburgh No.8 seam coal. The interaction between particle size, aeration rate, feed rate and wash water addition are examined in this investigation to establish the optimal operation conditions for flotation of fine coal. Despite of wide range of operation conditions used in this study, it is found that the experimental data fall in a single characteristic recovery-ash curve for a given bubble size distribution and particle size distribution. The major parameters affect the flotation performance points along -the characteristic recovery-ash curves are aeration rate/frother dosage, feed rate and wash water rate-.

Jan 1, 1994

The Lower Proterozoic metasediments of the Pine Creek Geosyncline form a chrono- stratigraphic sequence of mainly greenschist- and amphibolite-grade shallow-marine to supratidal pelites, psammites, carbonate rocks, and volcaniclastics which in places rests unconformably on Archaean basement. Granite and later dolerite intrude the sequence, and are associated with the major orogenic 1800-m.y. event which regionally metamorphosed the sediments. Most mineralisation is stratabound, and can be related at least partly to volcanic activity. Uranium mineralisation is mainly confined to particular carbonate-rich horizons near basement. Other metals are mainly in small hydrothermal deposits near intrusive granite. Specialist studies indicate that uranium was leached from its source rock, and probably carried as carbonate complexes in highly saline fluids at between 100 and 3500 C. Precipitation took place by redox reactions in breccia zones in carbonate rocks; these zones were formed by carbonate solution or diapiric movement of evaporites which preceded the carbonate. Extensive chloritisation in the ore zones suggests metasomatism by Fe- and Mg-rich fluids which may have evolved during dewatering of the evaporites. The main mineralising event took place after the 1800 m.y. metamorphism, and was probably

Jan 1, 1979

By Kot F. v. Unrug

In spite of extensive research and accumulated experience from mining operations, appropriate coal strength values for pillar design remain debatable. Coal strengths determined in the laboratory on standardized samples vary widely among various coal seams with poor repeatability. Penetrometric in situ strength testing obtains multiple measurements at multiple horizons within the coal seam to provide a strength profile. Alliance Coal has used that method in many of its mines for pillar design. Pillars in these mines perform well. This paper presents a series of case studies and discussion of issues related to coal pillar design. The analysis demonstrates that the proposed default in situ strength of 900 psi is appropriate when no other data exist. However, in the case of appropriate strength measurements combined with analysis of pillar structural composition, differing values can be used successfully. In areas where the penetrometric derived in situ strength is greater than the standard 900 psi in situ strength, reserve recovery has been optimized as required by law without compromising safety.

Jan 1, 2009

By I. N. Bayless

The subject of Premium Payments for Mechanical Loading was given consideration by the management, having in mind they would prove an incentive for increasing the tons per man shift, make for a lower production cost and allow the ambitious workman an opportunity to augment his earnings over the regular day wage rate, a standard of performance having been established by the operator which would be expected from the employee. Any performance above the standard is looked upon as a saving to the operator of which the employe benefited to the extent of receiving a certain percentage of the saving effected. The premium must be high enough to be worth while to the employee and low enough to in¬sure a saving to the employer. This method of sharing tends to pay men in accordance with their ability and effort. One of the principal advantages of this method of sharing is that a better class of labor may be attracted. Greater earnings furnish an incentive to increased tonnage. Workmen who prove themselves aggressive are readily noticed by supervisors, and, by shifting men to different places and to different working conditions, the crews are made more efficient and the inefficient workmen may be singled out and eliminated, thus permitting better results and better operation of the mechanical loading equipment. This is also evidenced by the fact that men become their own competitors, also working in competition with other crews. In order to do this, without neglect to the care and protection of the loading machines, men are educated to the proper handling and care of the machinery, keeping it in shape and everything clean in general, which has shown good results.

Jan 1, 1932

By Máximo Yaringaño

El presente texto describe la historia y las exploraciones realizadas en los distritos de San Gregorio y Colquijirca. Esta última se encuentra dividida en dos partes: Colquijirca propiamente dicha y Marcapunta, que es un yacimiento diferente -en tanto se halla emplazado en rocas volcánicas, mientras que San Gregorio y Colquijirca se hallan en rocas carbonatadas. Los tres yacimientos se encuentran en los Andes centrales del Perú, en el departamento de Pasco, Junín. La mineralización de San Gregorio está alojada en las unidades carbonatadas jurásicas del grupo Pucará, en su facies occidental; la mineralización de Colquijirca está emplazada en forma de mantos plegados en rocas carbonatadas de la formación Calera, correspondientes al grupo Pocobamba, de edad terciaria superior.

Apr 26, 1999

Large deposits present computational challenges to todayÆs commercial orebody modelling systems that are based on conventional block models. We describe a system that is specifically engineered to model and visualise large deposits. Central to the system is linear octree encoding of conventional block models and real-time conversion of three-dimensional (3D) meshes to linear octrees. We provide both methodological treatment and practical experience in implementing such a system. A commercial implementation is also presented to demonstrate the validity of the approach.

Sep 26, 2011

By David C. Oyler

Three long horizontal holes were drilled from a directionally drilled surface hole at the Emerald Mine near Waynesburg, Pa. The purpose was to adapt the technique of directional drilling for use in draining methane from coalbeds. A 504-m (1,652-ft) long, 76-mm (3-in) diameter, circular arc pilot hole was drilled, using a downhole mud motor, to enter the Pittsburgh coalbed at a vertical depth of 305 m (1,000 ft). The hole was reamed to 222 mm (8-3/4 in) and was cased to a measured depth of 486 m (1,595 ft). Three 76-mm (3-in) diameter horizontal drainage holes were then drilled, totaling 2,909 m (9,544 ft) of horizontal hole. Improvements in drilling methods increased the average drilling rate from 20.4 ill (67 ft) to 64.9 m (213 ft) per day. The cost of drilling the directional and horizontal holes (using a Government-owned drill rig) was $1,169,530, a figure inflated by inexperience and by delays caused by lost-circulation problems and fishing operations. An estimated total drilling cost of $960,000 (including rental of a drill rig) for an improved system, was determined by a detailed cost analysis. Initial gas and water production from November 1979 through May 1980 was low because of caving of the horizontal holes drilled in shale near the bottom of the casing.

Jan 1, 1982

By R. V. Ramani, P. M. T. White, D. Sutton

4.1 Introduction Using methods outlined in previous sections of this report, programs were written and/or obtained to: i) select best combinations of "a" and "k" for up to 8 different value parameters, ii) calculate available and unavailable ore tonnages and other statistics, and iii) produce contour maps of various parameter characteristics and available tonnages on a line printer. All the above programs are written in Fortran IV for execu¬tion on IBM 360/370 computers. 4.2 Calculation of Coal Reserves The Ore Reserve program suite consists of the following sections: (a) UNIT 1: This unit is a subroutine called by Unit 2 to determine values for "a" and "k" from the given data. (b) UNIT 2: These programs calculate ore reserves and are composed of a main program and several sub¬routines. In the following, their functions are abbreviated: i) MAIN - calls subroutines, reads run parameter variables, reads borehole data and interpolates grid node values for the area of investigation

Jan 1, 1974

By Fengyan D

Removing the interference of latter events, the data of geophysical (such as gravity and aeromagnetic) anomalies may indicate whether the mobile belt exist and whether the adjacent terrains of the mobile belt originally belong to one single unit. The petrotectonic assemblage can provide informations about the tectonic setting where it was generated from. The structural style can exhibit the kinetic and kinematic processes. The form of ancient isogeotherm may reflect the ancient geothermal regime which is related to the tectonic mechanism. In general, the early Precambrian terrains suffered polymetamorphism and multiple structural deformation. The researches must be carried out for the distribution of paleogeotharm and m.tamo'phic facies and zones on the basis of recovering the early structural style with structural analysis method; then a relatively correct conclusion may be geined on the ancient geothermal regime. This method can be known as "Ancient Thermotectonic Analysis". Through the sythetical research, a real knowlege about the tectonic setting of early Precambrian mobile belt can be obtained.

Jan 1, 1990

By P. W. Rainier

The Chivor emerald field is situated on the eastern slope of the Andes in the Department of Boyach, at an elevation of about 8000 ft. above sea level. It overlooks the Llanos (plains) of the Orinoco and is watered by many streams flowing into the Rio Meta, the Orinoco's largest tributary. The Rio Meta is navigable from the Orinoco to a point within about 50 miles of the Chivor district and may eventually prove to be the reasonable outlet for the future development of this part of the country. The topography of the district is extremely rugged and mountainous (Fig. I), the difference in elevation between two points on a mining claim 1 km. square being sometimes as much as 4000 ft. The ground is covered with dense forest growth and the available timber is suitable and sufficient for mining purposes, but it is becoming gradually depleted by Indian clearings as the country around the mines becomes settled. The many streams combined with the rough topography give good possibilities for hydroelectric power. The center of population nearest to Chivor is Bogoth, the capital of the republic and a city of some 300,000 inhabitants; the distance is two and one-half days' travel. The first stage of the journey from BogotB is accomplished by rail to Choconta, some 4 hr. travel. From Choconth the journey is made in the saddle, one night being spent in Guateque. The latter is a small town and the nearest post office to the mines, being some 10 hr. ride distant. The roads are mere bridle paths, in parts hazardous and almost impassable in the wet season. All supplies brought to the mines, other than those produced locally, are carried by pack mule; mule freight from Choconth costs 3 centavos1 per pound. The climate of the Chivor district is healthful and bracing. The wet season begins in March and concludes in November, the remaining months being dry. The annual precipitation is about 130 in. The temperature throughout the year is nearly constant, varying from about 45" F. to about 65" F. shade temperature. The rains are cold and unpleasant, and for the greater part of each day in the wet season the country is shrouded in dense mist. A fire can with comfort be kept burning in a living room all the year round. There are a few slight

Jan 1, 1931

By Ikuhiro Sumi

A new steelmaking process, in which manganese ore was intentionally reduced, was developed to achieve a higher manganese Yield using a combined blowing converter. In this study, manganese behavior was discussed through the introduction of a model. Apparent reduction rates of manganese were calculated by the two terms that were determined experimentally, with SOkg and 2S0ton combined blowing converters. The model calculated manganese changes during the operation. We applied the model to the actual operation and found that manganese behavior was predicted fairly well by this model.

Jan 1, 1996

By D. C. Williams, D. V. Carter

Four oil discoveries were made in east and east central Texas during 1940, three of which represented new fields. In the Chapel Hill field, Smith County, oil was found where formerly only gas and distillate were produced. The three oil fields discovered are: Hawkins, Wood County; Pittsburg, Camp County; and Tehuacana, Limestone County. Important extensions were made to the following fields: Bazette, Navarro County; Long Lake, Anderson and Leon Counties; Cayuga, Anderson, Freestone and Henderson Counties; Opelika, Henderson County; and Talco, Titus and Franklin Counties. At the close of the year 54 oil and gas fields were producing in the district. There were 13 other fields, 11 oil and 2 gas, which have been abandoned. The East Texas field led the district in the number of completions for the year. During the year about 622 wells (oil and distillate wells included) were completed and 80 wildcats were drilled. Production and Proration During the year 170,424,685 bbl. of oil (distillate production included) were produced in the district—a decrease of 2.6 per cent from the 175,053,729 bbl. (distillate production included) during the preceding year. The district's production for the year 1938 was 182,369,484 bhl. As usual, most of the district's annual production was in the East Texas field, which produced 139,095,694 bbl. (distillate production in- cluded) during 1940, or 81.6 per cent of the total oil produced as compared with 141,333,317 bbl. (80.7 per cent) for 1939. The December estimated daily average production in the district was 424,565 bbl. The district accounted for 34.9 per cent of the state's annual production, compared to 36.7 pcr cent of the state's 1939 production. The decrease in production for 1940 may be attributed to changes made in proration schedules. Any material changes in the district's annual production may be considered for the most part as a reflection of proration-schedule changes affecting the East Texas field, since it is by far the most important field in the area. The entire state was subject to 71 shutdown days for the year; the East Texas field to 131; and the Rodessa field (Cass County, Texas, portion) to 5 days. No important changes were made in field rules and regulations during the year regarding the allocation of oil in individual fields in this district. Discoveries The Hawkins field is in southeastern Wood County in and principally north of the town of Hawkins. Development to date indicates that the field is somewhat of an elongated anticline trending slightly east of north and the proved oil area appears at this time to cover approximately 4000 acres. The oil production has been secured from the Woodbine sand, Upper Cretaceous; a considerable quantity of gas has been encountered in the Sub-Clarksville formation (Eagleford shale) in the higher part of the structure. It appears that a free gas

Jan 1, 1941

By Sam S. Taylor

In most oil fields, natural gas is the major source of energy causing flow of oil to the well. The amount of gas produced with the oil generally exceeds actual energy requirements, so that in time the gas reserve of the field becomes seriously depleted and the oil production must be stimulated by some auxiliary means. One of these is to repressure the oil formation with natural gas; or, where a as supply is not available, often air is used. Although air is a cheap and convenient repressuring medium, its use sometimes is attended with several disadvantages. First, the return air-gas mixture decreases rapidly in fuel value, often until it can be used no longer as a source of power. At the same time, explosive mixtures may result if recycling is used, causing hazards to life and equipment. Second, sortie fields experience considerable trouble with the formation of emulsions which become increasingly difficult to treat. Although there is no definite proof that air repressuring always causes these emulsions, many operators are convinced that this is the case. The Petroleum Experiment Station of the United States Bureau of Mines at Bartlesville, Okla., has been interested in problems connected with air-repressuring for a number of years. Some time was spent in studying the so-called "bad gas"--return mixture of low fuel value. However, it appeared impossible to attack the problem successfully from this angle, and an approach was made through a laboratory-scale study of direct oxidation of crude oil.

Jan 1, 1934

By Yannick Bleuzen, Manuel Joao, Frederic Monath, Miguel Quaresma

The N1 Porto tunnel project is a 650m segment of large-scale civil engineering plan to improve traffic flow between Porto’s downtown district, the Santo Antonio hospital district and the highway access. The tunnel is being excavated into a massive “Granito do Porto” granite structure, 4 – 20m below a highly urbanized environment of Porto, Portugal. The project was originally started in 2000 and was stopped due to the inability to mechanically excavate the granite rock. The city of Porto engineers then turned to traditional drilling and blasting techniques. The use of pyrotechnical delay detonators did not easily comply with the specified environmental and safety requirements concerning blast charging, firing and vibration control resulting in the process taking far too much time. The introduction of digital blasting was proposed to overcome these concerns.

Jan 1, 2005

By Teruo Bitoh, Shogo Izumi

"The effect of B203 flux melting on the structure and the soft magnetic properties of the (Feo.1sBo.20Sio.os)96Nb4 bulk metallic glasses prepared by casting has been investigated. The ringshaped bulk specimens were prepared by the B203 flux melting and copper mold casting. It was confirmed that the flux melting promotes the precipitation of the a-Fe(-Si) and Fe2B phases in the central region of the specimens. The ring-shaped bulk specimens show a flat hysteresis curve, indicating a good linear relationship between the magnetic induction and the applied magnetic field. These results show that it is possible to develop a new soft magnetic material that exhibits constant permeability, which is necessary for producing inductors and choke coils.IntroductionSince the success of forming Fe-based bulk metallic glasses (BMGs) with good soft magnetic properties, great attention has been developed to synthesis and properties of the BMGs [l, 2]. The BMGs have high glass-forming ability (GFA) and, therefore, they can be used to prepare bulk amorphous alloys with a thickness of the order of a few millimeters by casting. The soft magnetic properties of Fe-based BMGs are better than those of ordinary amorphous alloys; therefore, these BMGs have wider applications as soft magnetic materials [3-5]. It is often required for soft magnetic materials that the shape of the hysteresis curve is changed according to the demands of applications. For example, materials with ""flat hysteresis curves,"" which means the magnetic flux density (B) and the applied magnetic field (H) show a linear relationship up to rather high magnetic field, are necessary for producing inductors and choke coils. Flat hysteresis curves can be easily achieved by creating an air gap in the magnetic path. However, magnetic flux leakage generated in the air gap inhibits high-density packing of the electronic components. In order to achieve flat hysteresis curves without creating an air gap, Fe-based ordinary amorphous alloys are subjected to crystallization by annealing and transformed into thin surface layers of a-Fe; the crystallization results in the compression of the remained amorphous phase [6]. Another way to achieve flat hysteresis curves is the formation of secondary phase (such as Fe2B) that act as pinning site of magnetic domain wall displacements [7]."

Jan 1, 2013