Search Documents

By Enrique Ibarra, Manuel J. Mendoza

"Abstract: This paper describes the current state-of-practice for the design of cast-in-place drilled shafts in granular soils under axial loading, addressing recent advances that take into account the surrounding soil grain size distribution and their behavior. The important role of the gravel content in the shaft response under axial loading is emphasized. Usual design approaches in Mexico are described, and the results of load tests from different sources are discussed. The analysis emphasizes the primary contribution of the lateral area of shafts to their axial bearing capacity, raising doubts regarding the common local idea of “point bearing shafts”. Finally, some lines of research are noted to permit advances in the important field of deep foundations. 1 INTRODUCTIONIn Mexico, cast-in-place drilled shaft foundations are widely used to support various structures in the west area of Mexico City, where alluvial and volcanic deposits predominate. Deep foundations are also used in modern construction works located in other major cities of Mexico. In fact, the use of drilled shafts for tall buildings and overpasses in the center of Guadalajara as well as in transportation works related to the Metro and roadways in Monterrey is well known. It is worth mentioning that these same structures have been applied in road bridges throughout the country.Procedures for pile construction in Mexico have been basically the same for the past 20 years (Paniagua et al., 2005); however, modern equipment has been incorporated into the construction industry, including innovations in sludge-drilling technology, control and the quality of the castings. In addition, novel and efficient procedures such as construction with continuous auger displacement piles have been implemented (Auger Cast in Place, ACP) and have begun to be used locally with success (Schmitter and Paulin, 2006).However, it can be argued that the technological developments that have resulted in more efficient construction procedures have not included a breakthrough in the full understanding of the phenomena or basic mechanisms of load transfer from piles to the surrounding subsoil and therefore in supported, tested and practical design methods. This is particularly true when seeking to determine the unit side shear strength of shafts drilled in granular media with gravels, where it has been observed that the commonly used calculations developed for sands underestimate the load-bearing capacity by frictionin a most important way. Due to the above reasons, it seemed appropriate to present in this paper a review of the current stateof- practice in Mexico for the design of cast-in-place drilled shafts, particularly in granular media, highlighting some recent advances and research that takes into account the grain size distribution and behavior of granular soil."

Jan 1, 2014

The first introduction of automatic control systems for flotation occurred about fifteen years ago. The early control work coincided with the introduction of on-line assaying using XRF techniques. This OSA availability, coupled with the emergence of small digital computers suitable for process control in the late 1960-s, meant that the necessary process information and control hardware existed for flotation control experiments. A period of intensive research related to flotation control. ensued. A great deal of effort was devoted to the development of mathematical models of flotation. Plant experimentation sought to understand the effects of a range of flotation variables on the process. Finally, control loops were proposed and plant tested. An evolutionary pattern emerges when the range of flotation control installations is examined. The earliest systems had as objectives process stabilisation using reagent control. There were also some early attempts at flotation optimisation procedures, again using reagent variation. Current work is still associated with the same objectives. One of the difficulties with flotation control has been to recognise and define clear and precise control objectives. More emphasis is now placed on cleaner control which has the advantage that the objectives are usually well defined. A number of flotation control systems which cover a range of control system types is discussed. Based on this accumulated experience,a list of good and bad practice in flotation control is Proposed.

Jan 1, 1983

By B. Haimson

A new loading apparatus was fabricated and used to conduct true-triaxial compression tests on KTB amphibolite, a crystalline basement rock. Tests in dry jacketed samples reveal that the intermediate principal stress has a significant effect on the onset of dilatancy and on rock strength, contrary to the implicit assumption made by Mohr-type failure criteria. Failure is induced through a shear fracture that dips steeply in the direction of the least principal stress. Experimental results lead to a new generalized strength criterion in terms of all three principal stresses. Unjacketed KTB amphibolite specimens, exposed to confining fluid, are considerably weaker than the jacketed ones, despite the negligible porosity and permeability. Failure is facilitated by several closely spaced subparallel tensile cracks normal to the least stress direction. SEM analysis suggests that microcracks developed upon dilatancy onset are penetrated and extended by the confining fluid, bringing about the unexpected rock failure mechanism at reduced stress levels. Un nouveau dispositif à chargement fut fabriqué et utilisé afin de réaliser un vrai essai de compression tri-axial sur KTB amphibolite, une roche cristalline du sous-sol. Les essais effectués sur échantillons enveloppés et secs révèlent que les contraintes principales intermédiaires affectent considérablement le début de la dilatance et la résistance de la roche, contrairement à la supposition fondée sur le critère de rupture de Mohr. La rupture est produite grâce à une cassure de cisaillement très incliner en direction où la contrainte principale est moindre. Ces résultats expérimentaux indiquent un nouveau critère de rupture général en fonction des trois contraintes principales. Les échantillons de KTB amphibolites sans enveloppe, exposés à un liquide confiné, sont considérablement plus faibles que ceux enveloppés, malgré la porosité et la perméabilité négligeable. La rupture est facilitée par plusieurs fissures de traction adjacentes et sub-parallèles, normales à la plus petite contrainte principale. L’analyse SEM suggère que les micro-fissures développent suivant le début de la dilatance, elles sont pénétrées et agrandies par le liquide confiné, produisant un mécanisme de rupture de roche inattendu, ceci à un niveau de contrainte réduit. Ein neuer Ladungsapparat wurde hergestellt um real - triaxiale Druckfestigkeitsversuche in KTB Amphibolit, einem kristallinen Grundgebirgsgestein, durchzuführen. Messungen in trockenen, bedeckten Proben zeigen that die mittlere Hauptspannung eine bedeutende Wirkung auf das Einsetzen von Dilatanz und auf die Stärke des Gesteins hat, im Gegensatz zu der impliciten Annahme auf Grund von Mohr-ähnlichen Versagungskriterien. Versagen ist induziert durch eine Scherfraktur die sich steil in die Richtung der geringsten Haupspannung nach unten senkt. Messergebnisse führen zu einem neuen, verallgemeinerten Stärke Kriterium dass auf alle drei Hauptspannungen basiert ist. Unbedeckte KTB Amphibolit Proben, die unmittelbar den umgebenden Fluiden ausgesetzt sind, sind wesentlich schwächer als bedeckte, trotz geringfügiger Permeabilität und Porosität. Versagen wird gefördert durch mehrere, nebeneinander liegende, sub-parallele Spannungsbrüche, normal zu der geringsten Spannungsrichtung. SEM Analyse lässt vermuten dass Mikrobrüche, die sich beim Überschreiten der Dilatanzschwelle entwickeln, durch die umgebenden Fluiden fortgepflanzt und weiter verbreitet werden, und unerwartet, auf Grund der reduzierten Spannungswerte, den Versagungsmechanismus des Gesteins einleiten

Jan 1, 2003

By B. K. Mishra, Partha Chakroborty

Jigs are the most important equipment used in the separation process that exploits the stratification of particulate matter under the influence of hydrodynamic and gravitational forces. Very little is known about the determined mechanisms by which particles of varying density, size, and shape stratify in a moving bed. A model is developed by using the discrete element method to understand the behavior of jig bed. This model is utilized here to study the stratification behavior of the bed and its control. The control action is based on the understanding of the physics of the stratification process within the framework of fuzzy logic. The actions suggested by the fuzzy logic controller (FLC) depend on the current degree of stratification and the existing frequency of the jig cycle. The results show that the FLC achieves efficiency in stratification with minor variations to the jig cycle.

Jan 1, 1995

By Kwang ‘Min’ Kim, Paul T. Behum

The Old Bevier Aerobic Wetland in Macon County, Missouri, was constructed between 1990 and 1991 by the Missouri Department of Natural Resources’ Land Reclamation Program for the purpose of treating acid mine drainage (AMD). The principal source of the AMD is from an underground mine that operated during the 1920's through 1950's, which was partially exposed during surface mining in the 1960’s. Limestone bedding of an AMD collection system provided alkalinity similar to an anoxic limestone drain (ALD). Because the original aerobic wetland failed when a critical dilution water supply became unavailable, the total acidity of the AMD overwhelmed the limited neutralization ability of the aerobic wetland. The aquatic vegetation deteriorated and treatment became ineffective. The Missouri Land Reclamation Program with the assistance of the Office of Surface Mining, Mid-Continent Regional Coordinating Center rehabilitated the Old Bevier Aerobic Wetland in 2001, incorporating newer technologies to improve the performance. The new system, Old Bevier II treatment facility, consists of a 2-stage vertical flow pond (VFP) with associated oxidation cells and aerobic wetlands. This paper discusses the performance of this passive AMD treatment system, updating an earlier report. The new treatment system has operated with nearly continuous net alkaline discharge and a high iron removal rate. Treatment improves during warm months when emergent vegetation is fully established and biologic activity is greater. Reduction in system efficiency is evident during winter months.

Jan 1, 2005

By R. F. Baxter, C. M. Read, R. I. McCulloch

"Globalization of the aluminium industry continues to increase the pace of change and the intensity of competition, while simultaneously, society demands better products, cleaner technologies and sustainable industries. Bechtel, a global engineering, construction and project management company, is not immune to either the opportunities or the challenges created by globalization. However, and not withstanding the challenges, for aluminium industry ""players"" with a true global perspective, globalization presents very real opportunities that may be leveraged to deliver value creating goods and services. The following paper will focus on the exploitation of one of the opportunities created by globalization in the Knowledge Management domain - the application of high level tools and methodologies to improve global delivery of greenfield and brownfield aluminium smelter construction projects. Specific examples will be presented of value driven solutions that were delivered at the early stages of project engineering."

Jan 1, 2006

By Magdelinka Padenkova-Yaneva, Emilia Christova Kostakeva

"One of the methods for waste treatment is composting during which as a result of controlled biological decomposition of organic waste in aerobic conditions harmless materials are received. Composting takes place in suitably designed premises which ensure the optimal conditions for biochemical decomposition of the waste. A usual way to process composting is the spreading of the waste on a base made from reinforced concrete.In the paper the phases and basic technical features of the process of composting, the requirements and properties of the base and the ways of protection of concrete base against corrosion are revealed. Technical decisions for a specific construction site in Bulgaria are shown and the advantage of achieving durability of the concrete constructions in the plant while achieving simultaneous environment protection from pollution is discussed.IntroductionComposting is the process of controlled biochemical decomposition of vegetable and animal organic waste in aerobic conditions as a result of which harmless materials are obtained. The latter have better stability and are rich in humus substances which are useful for agricultural crops and can be used for restoring the soil fertility [1, 2, 3, 4].In modern waste treatment plants a composting technology is adopted in which the waste is spread on a concrete base as piles with certain dimensions [1, 3]. These piles are periodically stirred or air is blown through them in order to ensure the quantity of oxygen required for the process of aerobic decomposition of the organic matter. The fluids and gases formed in the course of the composting are take away in order not to pollute the environment – air, water, and soils. For this purpose the base on which the waste is spread must satisfy certain requirements, and the gases must be taken away and rendered harmless in order to protect the atmospheric air from pollution. This paper discusses the need for protecting the concrete base from corrosion and characterizes the stages and main parameters of the composting process and the possibilities for primary and secondary protection of the concrete base from corrosion. Specific technical decisions applied in a composting facility in the area of the town of Plovdiv are presented."

Jan 1, 2008

By Arnold F. Stalder

The measurement of various gas concentrations in the atmosphere at a particular location has become a problem of considerable importance. Levels that need to be monitored vary from the range of percent for constituents such as oxygen to parts per million levels for gases like nitrogen dioxide. In particular, mine air can become contaminated with noxious or toxic gases from several sources: fires within the mine, diesel-powered equipment, and explosive sources. The contaminants that result are carbon monoxide (CO), carbon dioxide (CO2), and oxides of nitrogen (NO and NO2). Additionally, oxygen (O2) may be depleted. Thus, the workman can be exposed to potentially toxic or asphyxiating atmospheres. A device was needed that will continuously monitor the mine air in working areas and provide warning of hazardous atmospheres. The Mine Air Monitor was conceived as being a portable, rugged instrument capable of measuring the concentration of the various atmospheric constituents in the mine environment. The unit was to provide both warning signals and quantitative measurements when hazardous contaminants existed at too high a level, or when the oxygen was being depleted. The initial concept involved optical sensors for all of the contaminating gases to be measured, namely CO, CO2, CH4, and NO2, and an electrochemical cell to monitor O2. When the explosion proof requirements of Schedule 2-G made the concept appear to be unfeasible from the standpoint of weight and portability, the program was redirected and a three channel monitor employing electrochemical sensors was adopted. In this case the gases to be monitored were O2, CO and NO2. The remainder of the program was oriented towards obtaining good, commercially available lectrochemical sensors for the above gases, testing them, reducing deficiencies noted during these tests, and making the necessary modifications to integrate the three sensors into a Mine Air Monitor suitable for the mine environment.

Jan 1, 1974

By Tom Shumka

Introduction ?This technique detects 100% of all gear tooth surface indications, providing comprehensive data, and has the ability to size indications accurately. ?The remarkable advantages of ECA technology, is improved inspection capabilities and significant time-savings. ?The advantage of using EMCD is its ability to size indications accurately. ?This technique does not require the gear teeth to be wiped down by hand after cleaning as in MT, LT or UT inspections. (Figure 1) ?This technique will inspect one gear tooth in 30 seconds. ?All of the data can be archived for future comparisons in an electronic report. Methodology ?This technique utilizes Eddy Current Array (ECA) as the principle inspection technique. ?What has been added are specialty scanner probes with multiple coils, a multiplexer and a software package. ?With 2 and 3D dimensional isometric displays, the defect can be seen electronically as it is on the gear tooth surface, thus, reducing the reliance on human interpretation.

May 1, 2011

By H. E. Cross

In a minerals-recovery context, the object of exercising control over milling operations must be threefold, 1) To achieve maximum recovery at 2) minimum operating costs and 3) making maximum use of installed equipment, Milling is one of a sequence of operations which have as their objective the economic recovery of minerals from mined ores, All operations in the sequence are interdependent and each is both influenced by and itself affects all other unit processes. The part which grinding plays in achieving each of the above objectives is indicated in the following analysis: In South Africa, the most important mining operations are still the gold mines, A vast reservoir of knowledge and experience in treating the Witwatersrand and associated ores has been accumulated. and recoveries are consistently high, However residue values do vary and frequently this is due to fluctuations in the degree of grind, The significance of changes in residue values is indicated by the following example: On a modern mine, the residue values varied from 0,25 to 0,33 dwi; per 2000 lb, during a period of 6 months, The cash value of the gold thus lost varied therefore between $0.44 and $0.58 per 2000 lb, ton. A residue which assays 0.30 dwt per ton would contain approximately 0.26 dwt as undissolved gold and 0,040 dwt per ton as dissolved gold present in residual solution after filtration. This dissolved gold loss is a function of efficiency of filtration and varies from 0.030 to 0,.070 dwt per ton of residue.

Jan 1, 1970

By A. K. Sinha

Ever since electricity was introduced, electrical injuries and electrocutions have continued to occur regularly in coal mines. An analysis of the two hundred cases of electrocutions which occurred during 1956 to 1970 indicated that over 50 percent of the incidents were caused by the ineffectiveness or lack of electrical grounding. Research shows that various types of arbitrarily designed ground beds are in use and that the ground resistance and current are often very high and subject to wide seasonal variations. The results of a recent research are discussed in this paper.

Jan 1, 1980

By D. A. Stanley, B. J. Scheiner

The U.S. Bureau of Mines has thoroughly investigated the flocculation of phosphatic clay waste with polyethylene oxide (PEO). The studies included both theoretical and applied aspects of the flocculation sequence. The screen dewatering technique developed by the Bureau was field tested at four different Florida phosphate mines. The results of these field studies are presented. Also, to determine the mechanisms of the interaction of PEO with montmorillonite clays common to the phosphatic clay waste, a number of theoretical studies were conducted. An empirical equation was developed to describe the amount of PEO needed for flocculation. Infrared, ion exchange, and rheology techniques were used to study the interaction of PEO with Florida clays. The results of these studies are also presented.

Jan 1, 1993

By O. Hoover, M. Herman, V. V. Damiano

The Jetter and borie' teclznique of determining textures using a spherical specimen has been applied to tlze study of compression-rolled beryllium sheet. Snzall spheres the order of 1 mm in diam cut from the beryllium sheet were autotnatically rotated about tz41o axes using the G.E. single-crystal goniometer. Quantitative pole figures were obtained without tke need to apply absorption corrections. Compression-rolled beryllium exhibited peak intensities ,for (0002) planes of positions tilted 10 deg to the rolling plane and a near random distribution of (1010) planes about the nornal to the rolling plane. TECHNIQUES for determining textures of rolled sheet material are amply described in the literature. The techniques are found to be variations of two basic methods. One due to Decker, Asp, and arker, referred to as the transmission method, utilizes a thin-sheet specimen in which the X-ray beam enters the specimen from one side and the intensity of the beam which emerges from the opposite side is measured. The second method due to chulz,3 referred to as the reflection method, utilizes a thick specimen and the intensity of the beam emerging from the same side is measured. The two rotations of the specimen in the beam are designated a and 8. In order to completely determine the texture of sheet material, it is generally necessary to use a combination of the two methods. The calculations involved in correcting the raw X-ray data for absorption effects and the combining of the data obtained by the two methods are very laborious and time consuming. To avoid the intensity corrections which arise as a result of the changing diffraction volume and path length within the sample other methods have been proposed. The Norton method utilizes a cylindrically shaped specimen cut from the sheet material. Since the rods have rotational symmetry, the absorption correction is constant for rotations about the sheet texture. Jetter and Borie' employed a spherical specimen to analyze the fiber texture of extruded aluminum rods. The spheres were rotated rapidly about the fiber axis to include a large number of grains in the X-ray beam and changes in intensity with respect to tilts of the fiber axis were measured. The absorption correction was constant for all angles and was neglected. The Jetter and Borie' technique finds excellent ap- plication to very fine-grained low-absorbing metals in which the entire sphere volume can contribute to the diffraction volume. In the case of low-absorbing metals, however, serious limitations on specimen thickness occur as demonstrated by Braggs due to de-focussing effects. Peak shifts may occur which negate the assumption that integrated intensities are proportional to peak intensities. These limitations in sphere size to the order of 0.5 to 1 mm for beryllium require that the grain size be sufficiently small to include a large enough statistical sample. The present paper describes the application of spherical specimens less than 1 mm in diam to the quantitative determination of pole figures for compression-rolled beryllium sheet having a grain size the order of 10 p. EXPERIMENTAL 1) Specimen Preparation. Two techniques for spark-machining beryllium spheres were tried. One involved the use of a hollow cylinder as a cutting tool. The tool was fed into the rotating cylindrical specimen as shown in Fig. l(a). The hollow cylinder was carefully aligned such that the axis of the cylinder and the axis of the specimen lay in the same plane and were 90 deg to each other. As the hollow cylinder was fed into the rotating cylindrical specimen, a spherical shape was formed as shown in Fig. 1. Alignment was very critical. Slight misalignment resulted in the formation of a barrel-shaped specimen instead of a sphere. A second technique involved the use of a cutting wheel shaped as shown in Fig. 2 with a groove of the desired radius. A section of the sheet specimen was first turned into a cylinder on the left part of the cutting wheel. It was then shifted to the right and a spherical specimen was turned as shown in Fig. 2. The axis of the cylinder lay in the plane of the sheet. Flats corresponding to the rolling plane of the sheet were used to grip the specimen during the machining operation and these served to identify the rolling plane of the sphere. 2) Rotation of Spec=. The spherical specimen is shown mounted on the G.E. single-crystal goniometer in Fig. 3. The knob A of the goniometer shown in Fig. 3 rotates the specimen about the pedestal axis. These angles have been designated as @ angles. The knob B rotates the specimen about an axis perpendicular to the pedestal axis. These angles have been designated as p angles. A device was made to automatically drive the single-crystal goniometer by means of two flexible shafts connected to the A and B knobs as shown in Fig. 3. The motor system was designed to rotate the knob A, thus rotating the specimen through angles of $I while the B knob remained stationary. After one complete

Jan 1, 1967

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who called at Institute headquarters during the period May 10, 1916 to June 10, 1916: G. Aertsen, Philadelphia, Pa. Hennen Jennings, Washington, D. C. Frederick C. Alsdorf, Wickenburg, Ariz. H. M. LaFollette, LaFollette, Tenn. A. H. Anderson, Worcester, Mass. E. T. Lednum, Chicago, Ill. J. H. Batcheller, Mattapoisett, Mass. Francis Church Lincoln, Reno, Nev. Arthur B. Clark, Sheridan, Mont. H. Mortimer-Lamb, Montreal, Canada. J. Murray Clark, Toronto, Canada. Andrew W. Newberry, San Francisco, Cal. J. H. Collier, Oakland, Cal. C. E. Pettibone, Cleveland, 0. H. S. Emlaw, Spring Lake, Mich. Heinrich Ries, Ithaca, N. Y. E. L. Estabrook, Platteville, Wis. C. S. Robinson, Youngstown, 0. James W. Hambleton, El Paso, Tex. - M. K. Rodgers, Basin, Mont. James Henderson, London, England. E. J. Rossbach, St. Louis, Mo. G. P. Hulst, East Chicago, Ind. J. B. Tyrrell, Toronto, Canada. William F. Jahn, Riebeling, Mont. G. B. Waterhouse, Buffalo, N. Y.

Jan 7, 1916

By K. C. Wilson

Recent experiments and analyses have provided greater understanding of friction losses for the size distribution of the particles forming the slurry. Wilson and Sellgren (2001), Wilson et al. (2006) and Sellgren and Wilson(2006) have proposed a multi-component model consisting of carrier fluid and pseudo-homogeneous, heterogeneous and fully stratified solids. The technique presented here was found to estimate friction losses well when compared to reported experimental results with pipelines with diameters mainly from 0.2 to 0.5 m for various mixtures of fine sand to coarse gravel and products from mineral processing and phosphate mining.

Jan 1, 2007

By E. J. Lintner

This paper is one of a series being prepared by the United States Bureau of Mines describing clay mining and crushing methods and costs at various operations throughout the United States. These papers are designed to disseminate technical information regarding methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs might, in many instances, cause embarrassment to the individual operator as well as to the industry as a whole. On the other hand, operating costs are essential to a technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations may ensue. The author wishes to acknowledge the assistance of the following persons: L. W. Camp, general manager; S. Cooper, plant superintendent; and W. R. Riel, office manager.

Jan 1, 1936

By D. W. Fuerstenau

THE object of this article is to point out the experimental relationship which exists among contact angle, adsorption density, zeta potential, and flotation rate data. In each of the experiments discussed in this article, the surface properties of quartz, as a function of pH, were measured in solutions to which constant quantities of dodecylammonium acetate were added. Morrow1 and deBruyn2 worked with solutions containing 4.08x10-5 moles per liter, whereas Fuerstenau3 and Seele worked with solutions containing exactly 4x10 moles per liter, but this difference is not significant. The pH of the solutions was regulated with HCI or NaOH in all cases. In each case, the addition of collector was constant, but the concentration of dodecylammonium ions decreased because of the formation of dodecylamine at higher pH values2 Contact Angles: Gaudin and Morrow1 presented data for the contact angle of quartz in solutions containing 4.08x10-5 moles of dodecylammonium acetate per liter between pH 2 and pH 10.15. Using the same captive bubble techniques, the writer measured contact angles on quartz in solutions containing 4x10-5 moles of dodecylammonium acetate per liter at pH values ranging from 9.9 to 13.2. Both sets of data are presented in Fig. 1, in which the contact angle in degrees is plotted as a function of the pH of the solution. From pH 2 to about 8, the contact angle increases slightly with increased pH, but further increase in pH causes a sharp rise in the contact angle to a maximum of about 80º. At pH values above 11.6, the contact angle drops sharply, reaching zero by pH 12.6.

Jan 12, 1957

By H. A. Wentworth

THE Huff electrostatic plant of the United States Smelting Company operated in conjunction with its wet concentrator at Midvale, Utah, was the second plant of substantial size installed using the Huff process, and the first plant to be put in operation on the so-called Western complex ores. In spite of the machinery being of early design and consequently embracing many of the mechanical weaknesses incident to a pioneer plant the mill has operated steadily and uniformly since the summer of 1909, about five years now, without any material change other than some re-arrangement of the machinery for better handling of the sizes. The ore, at present coming almost entirely. from the company's mines in Bingham, is of practically the same composition as that upon which the plant was first put in operation. The crude ore, consisting of the sulphides of copper, lead, zinc, and iron, and containing small amounts of gold and silver, is brought by train and delivered to the hoppers of the wet concentrator, where by jig and table treatment, there are produced a shipping lead concentrate, a tailing and a middling product, the latter being conveyed in push cars to the adjoining electrostatic mill. The crude ore delivered to the wet concentrator contains from 6 to 9.5 per cent. zinc. At times the plant is used also for the treatment of custom ores from the Bingham district and elsewhere, and at such times the results of the plant vary according to the material in use, but as by far the larger portion of the product is that from the company's own mines, the results given below are fairly indicative of the general work obtained. The accompanying diagram illustrates graphically the flow of the ore through the electrostatic mill. The middling coming from the wet mill containing from 15 to 18 per cent. moisture is hoisted while on the cars by an elevator, and delivered from the top of the elevator to a hopper over the drier. The drier first installed was of too low capacity to take care of the moisture present in the tonnage to which the mill was later

Jan 8, 1914

By Marie Farnsworth

"The Anhydrite ProblemThe Nonmetallic Minerals Experiment station of the Bureau of Mines at Rutgers University, New Brunswick, N. J. has recently undertaken a study of the chemical and physical properties of anhydrite having in view its wider utilization anhydrite (CaSO4) in contact with water at ordinary temperature and pressure rehydrates, slowly forming gypsum (CaSO4.2H42O). In nature this is an extremely slow process, and laboratory experiments are being conducted to determine methods of accelerating the rehydration. The tests recorded herein cover one this study, and while they are negative in character in so far as the major problem is concerned, certain facts established by the tests, bearing on the stability relations of gypsum and anhydrite seem sufficiently important to be placed on record.Early Researches on Gypsum and Anhydrite.It is to Lavoisiar that we are the first scientific study of the calculation and hardening of plaster of Paris. He sums up his experiments in the following passage: ""If gypsum, which has been deprived of its water of by means of heat, is again treated with water (to make what is commonly called mortar) it takes it up with avidity, rapid and irregular crystallization occurs, and the small crystals which are formed are so entangled in each other that a very hard mass results."" Later, he observed that the dehydration of gypsum occurs in two stages: three-fourths of the combined water is much more easily driven out than the last fourth. LeChatalier first determined the temperature decomposition accurately, his method was as follows: Pulverized gypsum was placed in a glass tube in the middle of a paraffin bath, the temperature of which was raised in a progressive and regular manner. A thermometer gave at each instant the temperature the salt, and the passage of the mercury column past each division of —co. was cared by a registering chronograph. The rise in temperature was except at 128°C. and 168°C. where breaks occurred."

Nov 1, 1924

By Charles H. Fulton

The process of crushing ore in cyanide solution was first used at the Crown mine, New Zealand, in 1897, by Mr. F. R. W. Daw; and, two years later, Mr. John Hinton tried it experimentally at the old Dakota plant, Central City, South Dakota. To Mr. Hinton belongs the credit of introducing this important modification in the Black Hills, this being its first successful application in the U. S., and its results have been so satisfactory that it has become established as the proper manner in which to treat the dense oxidized siliceous ores of this district. Five mills are now crushing ore in cyanide solution, namely, the Horseshoe, 120 stamps (60 in operation); the Dakota, 30 stamps; the Maitland, 40 stamps; the Hidden Fortune, 60 stamps; the Lundberg, Dorr & Wilson, one 6-ft. Monadnock roller-mill; and several others intend to adopt this practice. The dry-crushing process still holds its place for the treatment of the more porous and open siliceous ores; and two mills continue to dry-crush dense siliceous ores. Character of the Ores. The occurrence of the ores of the Cambrian strata in the northern Black Hills has been frequently described.' In practice they are classified, according to their appearance, into " red " and " blue " ores, the former being oxidized and the latter unoxidized. At the present time, usually the red ores only are treated at the mills, although occasionally small quantities of blue ore, which have become intimately mixed with the red in mining, are included. Generally the extraction of values by the direct treatment of raw ore is from 70 to 75 per cent. for red ores, and from 25 to 50 per cent. for blue ores. The ores consist mainly of a siliceous matrix containing, as a +1SOUTH DAKOTA SCHOOL OF MINES, RAPID CITY, SO. DAK.

Jan 1, 1905