Search Documents

By Ed Clah, Catherine Aimone-Martin

The vibration response of a 30 in. diameter high-pressure (845 psi) natural gas pipeline to 11 coal mine blasts was measured. The X-52 steel pipeline was buried 7 ft. below the ground surface. Ground and pipeline motions in terms of velocities were recorded on the pipeline, in the ground adjacent to the pipeline, and near the ground surface directly above the pipeline. These data were used to estimate the maximum stresses and strains in the pipeline occurring during the blasts. Pipeline standoff distances varied from 264 ft. to 3720 ft. Two blast hole layouts and timing schemes were used. One represented highly confined blasts to limit movement of the shot overburden that generated high ground motions at the pipeline. The second represented patterns that provided greater relief and lower the ground velocities at the pipeline.

Jan 1, 2003

By M. M. Tilman

The Bureau of Mines investigated the precipitation strengthening of lead¬-base alloys containing 0.5 through 4 weight-percent combined Cd plus Sb. The Cd and Sb were alloyed in a 1-to-1 atomic ratio which maintained compositions along the quasi-binary section Pb-CdSb. Tensile properties, creep rates, and stress-rupture values were obtained on alloys in the aged condition. The highest tensile strength was observed in an alloy of Pb-3 CdSb, After aging for 6 months at 90°±3° F, this alloy had a mean tensile strength of 8,950 psi with 15-percent elongation. An aged alloy of Pb-1 CdSb exhibited a steady state creep rate of 1.2 X 10-3 percent per day at a stress of 500 psi and a temperature of 90°±3° F. Times to rupture at stresses up to 4,000 psi and at a temperature of 90°±3° F were obtained for some compositions.

Jan 1, 1970

By Chester R. McKee, Robert W. Terhune, Merle E. Hanson

The relationships describing the enhancement of permeability by firing explosives in boreholes have been derived and combined to yield permeability enhancement as, [ ] or the case in which the stress decays asymptotically as a power law kc and nc represent permeability and fracture density at the edge of the pulverized region near the cavity wall, f is a geometric attenuation factor, m is the dissipation due to real material effects, ko is the original permeability and rd is the scaled radius. This relationship has been compared with available measurements from the American nuclear shot "Hardhat", the French nuclear events in Hoggar granite and the chemical explosive shot in coal near Kemmerer, Wyoming. Significant correlation between this theory and the experimental measurement is observed. A comparison between single and multiple detonations shows that permeability enhancement falls off steeply near the shot; however enhancement can be considerable midway between two shots spaced 10 cavity radii apart. The degree to which enhancement, can be significant depends on material properties and fracture density. Porosity distribution from the explosive 1s the dominate parameter in permeability enhancement. Existing theories of permeability enhancement have also been reviewed.

Jan 1, 1976

The United States has not begun commercial operations to tap its largest poten-tial sources of oil supply - oil shale and coal. The reason is that domestic petrol-eum has been plentiful in the past and liquid products probably could be produced from it at the lowest cost. In view of the ever-increasing need for petroleum in the United States, the critical international situation threatening foreign supplies, the growing demands for steel, and the heavy costs to industry of constantly discovering and developing new oil fields, it is believed that the prompt development of a synthetic fuel industry based on oil shale and coal is not only requisite to safeguard our oil supply but is an economically sound course for the foreseeable future, To neglect its development is to close our eyes and minds to our own resources at a time when they are needed critically. It also is apparent now that neither the Government nor industry would be taking any considerable economic risk in starting the initial plants, especially as measured against their potential value in meeting critical oil and chemical demands and in building a new industry in the West.

Jan 1, 1951

By Edward Keller

ALTHOUGH the subject matter contained in this paper is presented under a new title, its writing was induced by the work of S. Skowronski and K. W. McComas.1 A discussion of the latter is here combined with the presentation of new and independent data. The physical constants quoted by the authors of that paper, such as melting and boiling points, as also the chemical reactions of the substances involved, are so well established that the numerous confirmatory experiments and their application to metallurgical conditions leave little or no room for criticisms. On the contrary, they will greatly aid to dispel any lingering skepticism as to possible considerable losses of copper accruing when the metal is melted in the presence of its own and, probably, other chlorides and when no provision is made for the recovery of volatile products. Exception may be taken, to some degree, to that part of the work under the caption Melting Drillings of Copper Mixed With Sodium Chloride. These experiments should have been extended in order to make the implied reactions clear and the results convincing. The latter are stated to be, "that when sodium chloride is present above certain minimum quantity relative to copper some of it is found to volatilize in the melt while another part reacts with the metallic copper to produce the volatile cuprous chloride, and that When smaller quantities of sodium chloride are present the reaction is complete and all chlorine is found to have volatilized as cuprous chloride." Metallic copper and sodium chloride are mentioned as the sole reagents in this chemical process, acting, according to the authors, in a neutral atmosphere of carbon dioxide. The chemist, quite naturally, will inquire into the formula according to which that reaction takes place and find that it would present itself as follows: 2Cu + 2NaC1 = 2Na + Cu2Cl2 It would appear that the truth of this formula will be challenged and a more rational explanation of the reaction sought. Apparently, carbon dioxide is neutral relative to metallic copper in its molten state; whether it remains neutral in the presence of sodium chloride is quite another question. Does it not at that high temperature become an oxidizer and do not the conditions of the reaction change to those expressed in the following formula? 2Cu + 2NaCl + 2002 = Na2CO3 + CO + Cu2Cl2

Jan 9, 1919

By Ken Baxter

The Sepon Copper Project is located in Laos and has a mineable reserve of approximately 16Mt of ore grading 5% copper with minor gold and silver values. The deposit is a clay-hosted secondary copper mineral suite, predominantly chalcocitic in nature with associated pyrite. The current project design is based on the production of 60,000t/a of LME Grade A cathode by an acid leaching process followed by solvent extraction and electrowinning. Significant metallurgical testwork was conducted as part of the Definitive Feasibility Study (DFS) with process challenges identified and overcome at each phase of testing. Flowsheet configuration is geared to autogenously generating sufficient acid and ferric iron to meet gangue acid consumption and to leach the copper. The ability to maintain acid and ferric levels in the process liquors is strongly influenced by the proportion of pyrite in the ore presented to the autoclave. This paper will outline flowsheet development from preliminary variability testing to pilot plant and DFS design. The Sepon process solution seeks a balance between operability and capital/operating costs, and provides insights into the basic mechanisms influencing flowsheet selection for these ore types.

Jan 1, 2003

By J. L. Christie

A recent case of failure of a-low karat gold alloy by stress-corrosion cracking is of interest because it illustrates a principle frequently overlooked: the relation between high residual stress and high yield point. The alloy contained Gold, per cent 39.6 Copper, per cent 51.1 Silver, per cent 5.2 Nickel. per cent 3. 1 Zinc, per cent 1.0 Tension tests on the alloy showed the following:

Jan 1, 1945

By Zervoudis J

Limitations of current touch-up solders for galvanised steel include coating thickness control problems and poor corrosion and abrasion resistance as well as health and environmental concerns due to toxic constituents such as lead. This paper reports on progress in ILZRO-sponsored research to develop an improved touch-up solder. Encouraging results were achieved in torch soldering trials with experimental zinc-tin-based alloys. Mouldability and coating thickness control were achieved over a practical working temperature range in which the solders consisted of a viscous mixture of solid primary zinc phase particles in a liquid zinc-tin eutectic matrix. The mouldability was dependent on the microstructure of the solder sticks, and optimum structures could be obtained through control of casting solidification rates and by the addition of small amounts of copper. Hardness, abrasion resistance, adhesion and corrosion tests on experimental Zn- (40 - 50 per cent) Sn-I per cent Cu also showed improved performance over lead-tin-zinc solders and compared the effects of tin content within this range. Atmospheric corrosion testing and optimisation of alloy composition and methods of solder stick production are continuing.

Jan 1, 1993

Machine breakdowns and maintenance delays are large contributors to lost production and increased operating costs in the mining industry. The U.S. Bureau of Mines is investigating the applications of expert system technology to diagnostic and predictive maintenance tor mining equipment. This will help increase mining productivity and decrease operating costs, by reducing the frequency of equipment failures and repair times. The Bureau has begun this effort by applying expert system techniques to the diagnosis of hydraulic system problems on a continuous mining machine. This paper discusses the development of the hydraulic diagnostic expert system.

Jan 1, 1990

By H. Akgun

Design of plugs for abandonment of boreholes and shafts may be governed by the bond strength between the plug and host rock. This paper presents the results of push-out tests on cement grout plugs in salt. Two expandable cement grouts have been tested. The average interface shear strengths ranged from 2 to 12 MPa. Peak shear stresses at failure, assuming an elastic stress distribution along the interface, were up to eight times higher. Standard deviations commonly reached 20%. Dissolution along the interface was observed, and may have been enhanced by clay inclusions in the salt. This dissolution appears to have reduced bond strengths. Application of the results to the design of plugs for larger openings (e.g. shafts, drifts, or boreholes) is discussed.

Jan 1, 1991

By Walter Valery, Lauren Hafla, Megan Tibbals, Adrian Dance, Jeff Snyder

"Newmont Mining Corporation’s Carlin (“Carlin”) operation processes roaster feed through a double rotator, dry grinding mill following secondary crushing. Metso Process Technology & Innovation (“PTI”) was involved in a review of crushing and dry grinding circuit operations in August 2009. A number of opportunities for increased throughput were identified in the PTI study.Extended plant trials were conducted in July 2010 to provide justification for possible circuit modifications and if needed, additional equipment. The trials confirmed that a finer crusher product would reduce the build-up of material ahead of the coarse grinding chamber in the double-rotator. Also revealed were material transport and airflow restrictions in the dry grinding circuit that resulted in a high circulating load.The secondary crushing plant demonstrated it was capable of reducing the amount of +¾” material in the mill feed thus increasing dry grinding throughput. However, wet and sticky feed affected screening efficiency resulting in low utilisation of the existing crusher capacity. The open circuit configuration also made it difficult to control crushing circuit product size.For the dry grinding circuit, changes in grinding media size, transfer grate design and increased airflow were recommended to reduce circulating load issues and increase circuit capacity. This paper summarises the crushing and grinding circuit review, the extended site trials performed by PTI and the improvements in dry grinding operation that resulted from this study."

Jan 1, 2012

By Richard H. Olson

Talc deposits in the Precambrian of southwestern Montana (Beaverhead and Madison Counties) are unique within the U. S. A. in that large bodies of tremolite-free talc can be open-pit mined. All known deposits are in pre-Beltian dolomite units. The origin is suspected to be metasomatic, with the siliceous component having been contributed by an intrusive Precambrian granite gneiss. Precambrian deformation was extreme and is characterized by multiple periods of tight isoclinal folding and the flowage of less competent rocks, rather than by faulting. Post- Precambrian folding has been relatively negligible; the characteristic Laramide structure is block-faulting developed along northwest-southeast trends. The talc is thought to have been formed in Precambrian time; the high-angle block-faults probably have no significance with regard to the formation of the talc, but do tend to complicate mining operations. Tremolite-free talc ore bodies with horizontal widths of more than 200 feet, vertical depths of several hundreds of feet, and strike-lengths of as much as one-half mile are known in the Ruby Range and the Gravelly Range. Where dolomite is interbedded with tremolite-free talc in the Gravelly Range, the scale of this relationship permits the use of conventional open-pit mining methods with subsequent upgrading by hand-sorting techniques. Underground mining has been used in the past, but all current Montana talc-mining operations are on the surface. The hand-sorted ore, some of which is shipped overseas, is finely ground or micronized in roller mills and fluid-energy mills. The products are distributed both nationwide and abroad.

Jan 1, 1975

By Henry Logan

THE purpose of mine-hoist safety con-trollers is to prevent hoists from being operated at speeds above those considered safe and expedient, to ensure proper accel-eration and retardation near the ends of travel, and to prevent overwinding. In other words, they are to safeguard the normal speeds and movements of the hoist-ing drums and cages. The object of this paper is to explain the fundamental principles of hoist controllers, and to aid in their selection, installation, and maintenance. There have been many designs of me-chanical hoist controllers, the basic ele-ments of which as ultimately developed consisted of a flyball governor and another movable member supported by a frame and arranged to move in a vertical, horizontal, or rotary direction, depending upon the particular design, the whole mechanism arranged to be driven in synchronism with the hoist drum. In case of overspeeding, inadequate retardation, or overwinding, a pawl or catch controlled by the governor would engage teeth or dogs on the moving member, which through mechanical con-nections would cut off the power and set the brakes.

Jan 1, 1940

By J. T. Duce

In viewing the petroleum world as a whole certain tendencies arc to he noted. The first of these is of a legal and political nature. It involves the nationalization of the oil industry; in some instances going into all its phases and in others with reference simply to production.

Jan 1, 1928

By P. Gelfi, J. Vanderbeek, J. Enriquez

"The Cerro Verde copper-molybdenum mining complex is located near Arequipa, Peru. A 108,000 t/d copper concentrator (C1 concentrator) commenced operation in late 2006 and was debottlenecked to a 120,000 t/d capacity in 2011. A feasibility study, initiated in May 2010, assessed the potential for expanding the processing rate of the large Cerro Verde sulfide reserve via the installation of a second, stand-alone, concentrator (C2 concentrator) capable of processing a nominal 240,000 t/d ore. The feasibility study was successful and the project advanced through engineering, permitting and construction. Ramp up to nameplate capacity was ahead of schedule. The overall project was completed on schedule and within budget. The details of the project and supporting components are described. The design philosophy and design basis of the concentrator facilities are discussed as are factors that influenced the concentrator layout. Risk mitigation features included in the design are reviewed. The factors that drove the successful and rapid ramp up to nameplate capacity are discussed. Operational experiences in the first year of plant operation and project lessons learned are described. INTRODUCTION/BACKGROUND Sociedad Minera Cerro Verde S.A.A. (SMCV) operates a copper mine near Arequipa in southern Peru. Small scale operations operated intermittently until 1970 when the deposit reverted to the ownership of Minero Perú S.A (Peruvian government). Minero Perú S.A. commenced mining and processing of oxide reserves in 1972 and placed an SX-EW plant into production in 1976. The ownership of the property has changed hands several times over the years. Minero Perú sold Cerro Verde to Cyprus Climax Metals in 1994. Cyprus was acquired by Phelps Dodge in 1999. Freeport-McMoRan (FCX) acquired Phelps Dodge in 2007. Several studies were undertaken during the 1990’s that tried to establish the economic justification to process the large primary sulfide resource that underlies the surface oxide deposit. None of these studies produced an economic conclusion until a feasibility study was completed by Phelps Dodge and SMCV in 2004. This study provided the economic justification for the construction of a 108,000 t/d concentrator during 2005 and 2006. The key to the success of this study was identifying a water source that was sufficient to support processing economies of scale. Concentrator operations commenced in late 2006. The original design production rate of 108,000 t/d was achieved on a 30 day moving average basis on the 266th day after ore was first introduced. During 2009, studies and evaluations were performed that had the objective of addressing observed concentrator bottlenecks to allow a production rate of 120,000 t/d to be achieved. The 120,000 t/d figure represents the sustainable production limits associated with the installed primary crusher and tailing thickeners which would have been prohibitively expensive to upgrade. Debottlenecking activities were implemented during 2010 allowing sustained production rates of 120,000 t/d to be achieved."

Jan 1, 2017

By Edward Saibel

The various theories that have been advanced to explain or predict the conditions under which a metal fractures may be divided into two categories: First, there are the macroscopic theories generally used in engineering practice. These are empirical in nature and limited in application. For example, the maximum normal stress criterion, which is quite satisfactory for a mild steel in simple tension at atmospheric pressure,' no longer suffices when this steel is pulled under hydrostatic pressure.2 In all of these empirical theories, the critical condition characteristic of the material and of the loading conditions must be obtained experimentally. Secondly, there are the theories based on interatomic forces,3'4 or on the energy required to form new surfaces.5,6 These have all dealt with the theoretical evaluation of the tensile stress necessary to bring about rupture in a purely brittle manner; that is, without plastic flow preceding fracture. All of these attempts have led to values of the tensile strength of crystals or of polycrystalline bodies that are 100 to 1000 times higher than observed values. On this account, it has been thought necessary by some investigators to conceive of a microcrack structure or distribution of flaws throughout the specimen such that the resulting stress concentrations provide the factor necessary to bring about agree- ment between calculation and experiment. It has been pointed out by several observers' that this point of view is highly unrealistic, in that the weakening effect of these flaws or microstructures must be very uniform from specimen to specimen, since the fracture stresses found for various specimens of the same material tested under similar conditions are so nearly constant. Furthermore, since calculations based on atomic forces or atomic energy are for purely brittle fracture, a condition probably never satisfied in tests, agreement is hardly to be expected. Thermodynamic Theory of Fürth In order to resolve this apparent discrepancy between the theoretical cohesive strengths and the observed fracture strengths, Fürth8 advanced a thermodynamic theory of the tensile strength of isotropic bodies based on work of Born relating to the melting of crystals. Assuming an isotropic material free from imperfections and flaws, behaving elastically up to the breaking point, and assuming a connection between rupture and the melting phenomenon, Fürth obtains an expression for the rupture stress a, in the form where Q is the melting energy per unit mass, p is the density, and is Poisson's ratio. Furth compares fracture stresses computed from Eq I with the fracture stresses of metals as given in the Landolt-Bernstein Tables (1927) and in the Hand-

Jan 1, 1947

By Russell R. Trengove

Bureau of Mines exploration at the property of the Tulare County Tungsten Mines was by core drilling from the surface from May 16, 1950, to July 13, 1950. The property is in the western foothills of the Sierra Nevada Range, 18 miles northeast of Lindsay, Calif. It has been in almost continuous production since 1942 and has produced 40,831 units of tungsten trioxide (W03) with a grade of approximately 67 percent. The work performed comprised a study of the geology, mapping the area, sampling the outcrops, and diamond drilling the area adjacent to the mine workings. Ten holes were drilled for a total of 1,824 feet. Ore reserves were found to be confined to tactite zones in a surface area approximately 250 by 400 feet and extending downward about 350 feet.

Jan 1, 1956

Sodium is added to aluminum-silicon eutectic alloys to modify the structure. The ideal amount is about 100 ppm but due to the fact that sodium is lighter than aluminum and can float to the surface where it bums, oxidizes ad volatilizes, a far greater amount is usually added. Furthermore, as the sodium is continually lost from the alloy the optimum amount is only present for a limited time. The net result is a process which is hard to control, produces fumes and a considerable amount of dross. It is shown that by electrochemically titrating sodium through a tube of sodium beta alumina electrolyte that the sodium can be added continuously in a controlled way. As the sodium is added to the bulk of the aluminum, there is no sodium on the surface of the alloy so that little surface oxidation occurs, and no fumes and dross are produced. This leads to an improved product and working conditions.

Jan 1, 1995

By I. Girón

El siguiente estudio revela la importancia del cultivo del selenio, propiedades, combinaciones y distintos usos en la industria y sistema de comunicación telefónica. Asi también describr el proceso de purificación y obtención de este compuesto mineral en Cerro de Pasco Corporation, destacando al Perú como uno de los países productores a nivel mundial, pese a su reducida proporción.

Jun 20, 1954

By Dwayne K. Rowlett

A lysimeter designed to measure suction and collect a pore water sample from unsaturated waste rock has been developed and its performance has been verified in two large scale column tests. The test columns were constructed to bracket the envelope of grainsize curves for waste rock from Northern Saskatchewan. The suction profile within the columns was measured under a series of infiltration rates using tensiometers and these were compared to the lysimeter readings. The rate at which pore water samples could be collected was also measured under each infiltration rate. Lysimeter measurements of suction were found to be slightly lower than the tensiometers.

Jan 1, 2000