Search Documents

By Roberto Parra

The selective reduction smelting of Cu2O in Cu2O-FeOx-SiO2 melts has been studied at laboratory level, using as a feed a dead roasted calcine from a copper concentrate. The purpose of the study was to evaluate the kinetic and mechanisms of the indirect reduction with CO and the direct reduction with graphite from 1260°C to 1350°C. The reduction rate by CO was found to be 10-2 to 10-1 mole Cu2O m-2s-1. The graphite reduction macrokinetics for FeO and. Fe2O3 containing melts, was found to be a first order reaction with respect to the Cu2O concentration, with a kinetic constant of 104 to 10-3 s-1. The reduction rate was not sensitive to temperature nor to stirring, in the range studied. The measured reduction rate is almost one order of magnitude larger than the observed rate for the direct reduction of FeO.

Jan 1, 1999

By P. Tsang, S. S. Peng

The stability of longwall chain pillars depends not only on the mechanical properties of the coal and surrounding rocks but also on geological and mining conditions. To evaluate the effects of each variable, orthogonal experimental design was employed in a significance analysis. The study concluded that the stability of longwall chain pillars is mainly controlled by the ratio of pillar stress to pillar strength, the ratio of the Young's moduli of roof to coal and floor to coal, entry width, pillar width and the internal friction angle of coal. Additionally, horizontal stress, panel width and mining height also play a significant role.

Jan 1, 1996

By Raymond E. Krauss

The McLaughlin Mine is based on a world class epithermal gold deposit located in the coastal thrust fault of northern California, about 1 12 air km (70 air miles) north of San Francisco. Owned and operated by Homestake Mining Co., the McLaughlin deposit contains about 18 Mt (20 million st) of gold ore at an average grade of 5.2 g/t (0.152 oz per st), or about 93 t (3 million oz). The area was identified as a gold target by Homestake in early 1978. Drilling confirmed it to be a commercial deposit by 1980. The mine was then planned, engineered, built and brought into production by March of 1985. The deposit was historically a part of the Knoxville District. It was mined for cinnabar, which was used to produce mercury for use in recovering gold and silver in the Mother Lode and Comstock districts. At that time, the mine was called the Manhatten and later the One Shot Mine. It was worked for more than 100 years, producing about 76,000 flasks of mercury without any awareness of the presence of economic concentrations of gold. By 1978, the site was largely disturbed and entirely unreclaimed.

Jan 1, 1990

By Mike Stanley

This is a case study of an opencast coal mining operation where the physical and financial performance was improved via applying a process of transformational leadership development. [ ]

Jan 1, 2008

By A Bagchi, Nabiullah, Jagdieh

"A number of coal mines in India are affected by fire. Most of coking coal reserves in the country are located in Jharia coalfield where more than 18 sq. km is in the grip of fire. Generally such fires are confined in areas near to our crops. About 37 million tonnes of coking coal are lost in recent yearsdue to fire and another 48 million tonnes are blocked in fire areas. Preventive measures adopted to control fires were only partially successful and the cost of such measures was exorbitant I Temperature of blast holes in fire area varies between 60 and 300° C or even more. Even after thorough quenching of holes with water, it become difficult to bring down the temperature below SO"" C. For blasting hot holes primary need is to select safe and suitable commercial explosives and detonating fuse and to measure hot hole temperatures. VWiOUs types of commercially available explosives including Nitro Glycerine bare, slurries, site mixed slurries (SMS), emulsion5 ,detonating fuses and detonators were tested to determine their thermal behaviour at elevated temperatures under field simulated conditions in the Copyright © 2000 International Society of Explosives Engineers 1993g - Studies on Safe Blasting Technique in Fire Area of Coal Mines laboratory and in hot blast holes in field . More than 50 round of blast were conducted in fire areas. NG base compositions and detonators were found unsafe at temperature above SO0 C andtherefore, they are not permitted to be used in hot holes. Slurries and emulsion are stable upto 1200 c. For blasting at temperature exceeding SO0 C a heat resistant gel/ solution was developed by the authors and is being used in number of fire areas."

Jan 1, 1993

By W. G. Woolf, A. Y. Bethune

THE hydrometallurgy of special high-grade zinc as practiced by the Sullivan Mining Co. at its electrolytic zinc plant, Kellogg, Idaho, involves an important filtration step immediately following the leaching process. By means of the filtration the heavy zinc sulphate solution is separated from the residual products which remain after the zinc calcine has been dissolved in the sulphuric acid electrolyte. Because this plant uses the so-called high-acid, high-density process' for the production of First, the strength of the electrolyte (270g H,SO, per liter) results in a saturated zinc sulphate solution, having a specific gravity of 1.510 to 1.540, which must be kept warm during filtration because of its property of "seeding out" small crystals if allowed to drop much below 60°C. Second, the action of the "high" acid on zinc calcine under the temperature conditions of the leach (80" to 102 "C), although favorable to good zinc extraction, causes a considerable quantity of iron to be dissolved (8 to 18. g per liter) along with variable quantities of alumina and silica, depending on the grade and type of original zinc concentrates roasted. These three, iron, alumina, and silica, are almost completely precipitated during the neutralization of the leach (only a few. milligrams per liter of each remain in solution), so that the resulting pulp, instead of being a granular, sand-like product having a particle-size distribution dependent on the fineness of the zinc calcines leached, is in reality a slimy, chemical precipitate whose filtration characteristics constantly change depending on the amounts of iron silica, and other impurities, which are dissolved and reprecipi-tated. Third, the combination of supersaturated solution of high specific gravity plus a dense, semi-gelatinous residue creates a difficult washing problem requiring a positive displacement wash to liberate the zinc sulphate entrapped in the pulp. In a closed-cycle hydrometallurgical operation, such as practiced in this plant, the extent of washing is determined by the volum,e limitations imposed on the intermediate wash waters by the amount of "fresh" (or process) water which may be added. The volume of fresh water used for makeup purposes is limited to the amount which is lost during the closed cycle by evaporation in the leach, sulphate content of the calcines leached, moisture content of the residue, and spillage. The Burt filter as modified and improved by the Sullivan Mining Co. has successfully met and overcome these difficulties under a variety of zinc plant operating conditions since 1928. It might have many interesting applications to metallurgical fields other than that of electrolytic zinc, and its possible usefulness to hydrometallurgists in general warrants its description and discussion. The Burt filter is so named from its inventor who originated it in Mexico for pulp filtration in the cyanide process for gold and silver ores. While retaining the basic principle of Burt's earlier revolving pressure-type filter with internal filtration media, a number of modifications and improvements have been made in Sullivan Mining Co.'s installation. The Burt filter may be classified as a batch-type pressure filter in contradistinction to either the conventional vacuum-type filter, which depends on atmospheric pressure to force solution through a cloth medium, or to the filter-press, which employs whatever pressure is imparted by the pump delivering the liquid being filtered. The Burt consists essentially of a hollow steel cylinder about 40 ft long, 5 ft in diameter, resting horizontally, and capable of rotation about its long axis. It is supported on one end by a hollow trunnion and near the other end by a riding-ring and roller combination. The cylinder is lined with filter units each fastened against the inside of the shell and parallel to the long axis so as to form a hollow cavity into which pulp may be charged. A specific amount of pulp is admitted to the filter and a unique valving arrangement prevents the loss of pulp while air pressure forces the solution through a canvas medium to the discharge port of each filter unit. The residue is left on the surface of the canvas inside the cavity. The remainder of the filter cycle is concerned with washing the residue free of zinc sulphate, discharging it from the Burt, and preparing the filter for the next charge. A more detailed description of Burt filter construction, a typical filter cycle, and its operating characteristics when employed on material encountered in this plant will be given in that order. Description of the Filter: Fig. 1 shows a side elevation view of a filter with riveted shell construction. Since this drawing was made shells have been fabricated by welding, instead of riveting, with complete success. Shells are lagged on the outside to retain heat. Fig. 1 shows a side elevation and plan view of a Burt filter in operating position. The 1/2-in. steel shells are lined with 3/16-in. copper sheet as protection against the corrosive action of the solution (containing about 500 mg Cu per liter) on iron, and the copper is given a thin protective coating of plastic-base paint. Fig. 2 is a view from the discharge end of the filter, with head removed, before filter units are fastened to the periphery. It shows

Jan 1, 1951

By C. Edwards

"The processes for rare earth (RE) extraction include the decomposition of RE ore concentrate minerals, and the concurrent or subsequent leaching of the rare earth elements (REEs) from the decomposed minerals. Ore beneficiation concentrate can be decomposed by, for example, acid roasting, caustic cracking, and chlorination. The REEs can be selectively extracted. The nature of the REE extraction process depends on the concentrate mineralogy and the targeted products. Based on the experience of the Saskatchewan Research Council (SRC) in RE processing, this paper reviews REE extraction from the major RE minerals, including bastnaesite, monazite, xenotime, ion-adsorption clay, allanite, cerite, and eudialyte. An update on the development of RE extraction processes is also provided.INTRODUCTIONRE processing usually involves two operation stages, physical processing and chemical processing. Physical processing, also known as ore beneficiation, separates the RE minerals from gangue minerals to produce an RE mineral concentrate. Chemical processing, which includes extraction and separation processes, converts the RE mineral concentrate to an RE compound which is either an end product or an intermediate product for the subsequent production of individual REEs or other compounds. The RE extraction process uses one or more reagents to decompose the RE minerals and to leach the REEs into solution. The RE separation process uses solvent extraction, ion-exchange, or chemical precipitation to produce either rare earth oxides (REOs) or individual REEs. The authors have previously reviewed RE ore beneficiation processes (Zhang & Edwards, 2012). This paper focuses on extraction processes for a variety of RE minerals. Table 1 gives the chemical compositions of the RE minerals mentioned in this paper. The varieties of RE extraction methods use many different reagents. These reagents are mainly inorganic acids, alkalis, salts, and chlorine gas. The commonly used acids include sulfuric acid (H2SO4), hydrochloric acid (HCl), and nitric acid (HNO3). Sodium hydroxide (NaOH) and sodium carbonate (Na2CO3) are the most common alkalis. Salts include ammonium sulphate ((NH4)2SO4), ammonium chloride (NH4Cl), and sodium chloride (NaCl). HCl is normally used to extract RE from silicate ore minerals such as allanite and gadolinite. The alkalis and H2SO4 are mainly used to leach REs from phosphate ores minerals like monazite and xenotime. The carbonate ore RE minerals such as bastnaesite can be treated using either acids or alkalis. HNO3 is mainly used to leach eudialyte and apatite. The extraction of REs from ionadsorption clay deposits uses salt solutions. Chlorine gas (Cl2) is exclusively used in the RE chlorination process which can be used to treat any RE minerals."

Jan 1, 2012

By Pan, Jian, Siwei Li, Deqing Zhu

"It is great significance to realize the efficiently and comprehensively utilization of iron, manganese and aluminum from refractory high-aluminum and high-manganese iron ores. Aimed at the two types of low grade refractory iron ores, mineralogical characteristics were studied. The direct reduction behaviors and evolution of mineral compositions of single iron ores and their blended ones were analyzed, and the corresponding reduction mechanisms were demonstrated. The results showed that only a part of iron oxides in high-aluminum ore are transformed to metallic iron after reduction, while the other react with aluminum and silica to form fayalite and hercynite which are difficult to be reduced. For the high manganese iron ore, most iron oxides can be reduced to metallic iron and manganese oxides can combined with aluminum-silica minerals to form galaxite and tephroite, promoting the reduction of iron oxides. Co-reduction results demonstrate that reduction of high- aluminum ore can be promoted by adding with high-manganese ore. Metallization and metallic iron grains increase dramatically by elevate high-manganese blending ratio. At the ratio of 60% high- manganese iron ore in the pellet feed, iron-slag separate well with a slag assaying 28.51%~36.35% Al2O3 and the recovery of iron and manganese can be reached 93%, respectively. The high-aluminum rich manganese residue was recycled with H2SO4. INTRODUCTION The growth of the Chinese iron and steel industry has been pushed forward by its rapid economic development in recent years, and 1126 million tons of iron ore have been consumed in 2014, where 933 million tons were imported according to the data from World Steel Association [1]. However, iron resources are limited, and especially the reserves of high-grade iron ores are declining, so it is of significant importance to optimize the mining rate of iron resources [2] and to utilize low- grade refractory iron resources, such as high-aluminum iron ore."

Jan 1, 2018

ROSWELL H. JOHNSON,* Pittsburgh, Pa.-The industry, I think, has suffered very severely from the lack of just such work as has been done by Messrs. Lewis and Beal. I think we owe a great deal to the Bureau of Mines for at last undertaking this much needed work, even though it is so belated. It could have been of very great assistance in so many properties where its usefulness has now passed. I think it is perhaps well to sound a note of caution, owing to the fact that so much of this information was derived from eastern Oklahoma; but with the new bulletin giving the decline for many fields, there will be far less danger of falling into error through assuming too much uniformity. The cumulative percentage curve seems to 'me to be a. particularly splendid idea. It should have a very important -influence, especially as the authors have themselves pointed out several variables that ought to be taken into consideration. The thickness, I think, is going to be an especially important one to work out along the general lines of method that they have advanced. Probably the most surprising thing in the paper is the general rule that the decline of a well is more correlated with its size than with its age. I can't help but think that that generalization, important as it is, is rather rough and will not apply so clearly when we have a larger number of fields before us. Still the generalization, rough as it is, is of very great importance, since the industry has been very largely basing a great many of its ideas on the ignorance of that principle. It leads to certain corollaries that are of great consequence. The first is that the undrilled portion of the property must be appraised on a. different basis from that used for the drilled portion.

Jan 4, 1918

By A. Martin

Detailed porewater profiles of arsenic and other interstitial metabolites were used to assess the relationship between trophic status, sediment redox chemistry and arsenic mobility in a historic tailings repository. The results demonstrate that in eutrophied systems which exhibit greater sediment oxygen demand, the depth of the Fe(III) redoxcline, and hence depth of arsenic release, may lie in close proximity to the sediment-water interface. As a result, arsenic scavenging mechanisms are significantly reduced, resulting in a greater flux of arsenic to the water column. Such considerations have important implications for the management of pit lakes, tailings ponds and contaminated lakes which may consider: 1) the discharge of sewage to the water body during operations; and/or 2) post-closure fertilization as a remediation strategy.

Jan 1, 2002

By D. O. Hobson

Zirconium single crystals of various specific orientations were fabricated by rolling or drawing. The resulting textures were determined and are discussed with respect to the deformation modes that produced them. The crystals deformed in a predictable manner by combinations of up to third-order twinning with three twinning modes and by slip. Twinning was found to play a major role in initial texture formation. Texture changes produced by slip occurred only at the higher reductions. The twinning sequences that produced each intensity peak during the initial reductions could be identified. Schmid factor criteria were found useful in predicting which deformation modes to expect for each crystal orientation and fabrication procedure. The possible application of these data to poly-crystalline material is discussed. PREFERRED orientation or texture has a significant effect on the properties of most materials, causing anisotropy in fabricated cubic metals and enhancing the natural anisotropy of noncubic metals. This study evaluates the effects of several fabrication methods on the textures formed from specific starting orientations of zirconium single crystals and, it is hoped, gives an insight into the effects of the same operations on poly-crystalline material. BACKGROUND In fcc and bcc metals, texture changes take place by gradual lattice rotations caused by the operation of one or more slip systems. Deformation twinning plays an insignificant role in the deformation of such metals. In zirconium and its alloys, however, and in many other hep metals the ability to twin allows very rapid texture changes to be made with very small amounts of deformation. The deformation systems found in zirconium and its alloys are prism slip and three twinning modes.1 Slip occurs on the {1010}< 1120) system. There is little or no appreciable basal slip in zirconium. The twinning planes, illustrated in Fig. 1, are {1012}, {ll2l}, and {1122}. Two twinning modes, the {1012} and the {ll2l} operate for a tensile stress along the basal pole. A compressive stress parallel to the basal pole is required for {ll22} twinning. These twinning operations cause a 35- to 85-deg reorientation of the basal pole. The {1012} twin is the predominant tensile twin at room temperature. The twinning shears, S, are shown in the figure. A criterion for predicting which deformation system will operate when a grain is subjected to a known stress state is the Schmid (orientation) factor. This factor gives the fraction of the applied stress that computer program was written2 to calculate the Schmid factors for the four deformation modes in zirconium. It assumed three orthogonal stress axes and considered ninety-one different orientations of the basal pole in one octant of this stress space. At each basal pole position the Schmid factors were calculated for seven positions of rotation at 10-deg increments of the unit cell about the basal pole. Schmid factors were determined for a total of 637 orientations and for twenty-four deformation systems in each orientation. The program listed the Schmid factors for uniaxial stress parallel to each axis and, to approximate rolling, or-thonormal biaxial stress was also considered. Fig. 2 shows the range of orientations over which the various types of deformation would tend to predominate in biaxial plane strain with the stresses, equal magnitude. The exact boundary position between regions of different deformation modes depends, however, on the relative values of the critical shear stress for each deformation mode. Fig. 2 is drawn on the assumption that they are equal and it therefore may be only approximately correct. It is also recognized that the biaxial stress analysis may not be applicable in certain crystal orientations. EXPERIMENTAL PROCEDURE Single crystals of zone-refined zirconium, produced by Wilson of this Laboratory,3 were electrical-discharge-machined to form specimens for rolling, tube-drawing, and rod-drawing studies. Specimens were rolled at room temperature on 2-|--in.-diam hand-powered rolls from three different starting orientations: 1) the basal plane parallel to the rolling plane and the [1120] in the rolling direction, (0001)[ll20]; 2) the (1120) plane parallel to the rolling plane and the basal pole in the rolling direction, (1120)[0001]; and 3)_the (1120) plane parallel to the rolling plane and the [1100] in the rolling direction, (1120)[ll00]. Drawing specimens were cut with the [0001] direction as the drawing direction in the tube blank and [1120] as the drawing direction in the rod specimen. The drawing

Jan 1, 1969

It is shown that factors associated with conditions whIch are thermodynamically favourable for the formation of CuS04 in roasting lead to high copper recoveries on leaching. One of these factors is the ratio of the air to solids used for roasting. This can be varied widely without loss of temperature control in the sulphating roasting of many Australian copper concentrates.Thus, the prediction of the air to solids ratio corresponding to a maximum p(SO3) value, for a given concentrate and temperature, is of importance in fluidized bed roasting, since this could be associated with the formation of a maximum quantity of CuS04. Calculations are presented which predict this air to solids ratio, not only for a given concentrate composition, temperature, and pressure, but also for air which is enriched with sulphur dioxide or oxygen.

Jan 1, 1968

By B. Ramaswami

INTERNAL oxidation occurs readily in silver due to the rapid diffusion of oxygen in silver.&apos; It has a marked effect on creep in polycrystalline silver2 and raises the critical resolved shear stress in single crystals of silver.3 However, the effect of oxygen on the work-hardening parameters of silver is not known. It is the aim of this paper to describe the effect of internal oxidation on the work-hardening characteristics of single crystals of silver and an Ag-0.1 at. pct A1 alloy. The materials used were: 99.99 pct Ag from Handy and Harman and 99.993+ pct A1 from Alcoa. Single crystals, 6 mm by 6 mm in cross section of silver and Ag-0.1 at. pct A1 of mo.5 orientation, i.e., the orientation with the Schmidt factor m = 0.5. were grown by the Chalmers technique.4 One set of specimens, referred to herein as oxidized specimens, was annealed at 940°C for 24 hr in a muffle furnace, in air, and furnace-cooled to room temperature. Another set of specimens, referred to as nonoxidized specimens, was annealed in oxygen-free helium at 940°C for 24 hr and furnace-cooled over a period of 7 hr to room temperature. The annealed single crystals were tested at room temperature in a floor-model Instron testing machine. The results are presented in Figs. 1 and 2. A

Jan 1, 1965

By Earl G. Alexander, W. R. Runyan

The nature of silicon growths which form on amorphous silicon dioxide during epitaxial deposition in unmasked areas was investigated. Octahedral silicon crystals nucleate and grow on the oxide at pinholes, adjacent to foreign matter, and probably at oxygen-deficient sites. Generation of these oxygen-deficient sites on the oxide surface is shown to be thermody-namically favorable under usual deposition conditions. The conditions which affect saturation (SiCl4 concentration, flow rate, temperature) determine the number of sites on which silicon will nucleate and grow. Reaction product HCl is likely responsible for suppressing silicon growths on the oxide near exposed areas of silicon. Evidence is given that the oxide-silicon interaction occurs in hydrogen only and involves water as a transport agent. SINCE shortly after the first epitaxial layers of silicon and germanium were grown over large areas, efforts have been underway to grow selectively on specified portions of the surface. Such selective growth should be particularly applicable to monolithic integrated circuits. Usually the approach has been to use a mask to delineate the desired area,&apos;-7 but the VLS methoda can also be used, and direct programmed atomic beam deposition has been suggested.9 The masking techniques may embody two forms: in one the mask is a material which can later be removed along with any growths attached to it; in the other, attempts are made to prevent growth on the mask, so that over a whole slice the only deposition that will occur is in the unmasked regions. The present work is concerned with only the latter case, and specifically with silicon. Joyce and Baldrey1 suggested the use of thermally grown silicon dioxide as a mask material and showed that for the proper choice of operating conditions (total flow, SiCl4 concentration, total deposition time, and temperature) spurious growth could be minimized and that if the deposition times were not too large, and the criteria not too stringent, a usable process occurred. Later Schnable et al 4 observed that after extended deposition times, during which most of the silicon dioxide became covered with growth, there was always a band of oxide around the exposed silicon area that was quite free of spurious silicon crystallites. This latter observation is particularly intriguing since it extends the hope that with proper precautions masking can be much more versatile than it presently is. EXPERIMENTAL PROCEDURE Silicon substrates oriented to within 1.5 deg of a (111) plane were prepared by etch polishing lapped

Jan 1, 1967

By W. J. Long

As a part of the strategic mineral exploration program, examining engineers of the Bureau of Mines collected samples of ore from four manganese properties in Yavapai, Yuma, Maricopa, and Mohave Counties, Ariz. As all of the ores were too low in grade to be acceptable by manufacturers of ferromanganese beneficiation studies were made to determine the amenability of the ores to concentration.

Jan 1, 1948

By R. Biss

"Niobium or columbium, as usually called in North America is becoming a more and more important metal in the industrial world because of its attractive properties.Eventhough discovered in the early nineteenth century, it was not until the 1930's that its use became more widespread. The discovery of large commercial deposits in the late 1950's and the demand of industry for steel with high strength and toughness further promoted its use. To assure its adequate supply new or-e processinr technologies had to be developed. So, beside the traditional gravity concentration, the flotation process was employed for the partial upgrading of pyrochlore concentrate at S8ve (Norway) plant in 1953. The flotation process was equally used at St-Lawrence Columbium plant in the province of Quebec, Canada. The new plants at Araxa and Catalao in Brazil and at St-Honore, Canada, which supply almost of all niobium used today in the non-Communist world, also adopted the flotation process. The processes using long chain aliphatic rnonoarnines, diamines or sulfonates as collectors proved to be difficult especially on weathered types of ores or on those having a substantial content of silicate gangue minerals. They almost completely failed in case of alkaline intrusive rocks as syenites, nepheline syenite, ijolites and pyroxenites, composed almost entirely of silicate minerals. A lot of effort was devoted all around the world on research of new, more efficient flotation processes. So in 1982, Les Services T.M.G. Inc. (Niobec), sole producer of pyrochlore concentrate in North America, developed the direct pyrochlore flotation process from carbonatites. In 1983, at about the same time, the Quebec Department of Natural Resources Laboratories and Les Services T.M.G. Inc. announced a successful recovery of niobium Minera1s from a low grade nenheline syenite ore."

Jan 1, 1984

By G. A. Irdi

An automated method of microscopy for determining the pyrite size distribution on two base coals that were crushed to 28 mesh x 0 has been developed. Polished epoxy-bound coal pellets were prepared and examined by a Zeiss IBAS image analyzer utilizing a program developed from provided software. Pyrite size distribution determination is considered a necessary first step in pyrite characterization that could lead to successful predictions, by microscopy, of a coal&apos;s theoretical pyritic sulfur removal. Our research efforts to date have indicated that the IBP-S can be a reliable instrument for determining pyrite size distribution in crushed coal. A program was also developed to convert pyrite size data to a weight basis for comparisons to the results from chemical analyses. The problems encountered in our research and their solutions will be presented in the discussion.

Jan 1, 1986

By James V. Luxner

The airflow and methane distribution patterns developed in an equipment-free entry 6.5 feet high and 12 feet wide, ventilated by line brattice operated blowing to or exhausting from the face, were determined by the Bureau of Mines for varying conditions. Results of these studies show that blowing line brattice systems of face ventilation are more effective than comparable exhaust systems. The face ventilating efficiency of any line brattice system is dependent upon the method of ventilation, the face distance, the tight rib distance, the volume of air delivered to the end of the line brattice, and the volume of methane released at the face. Experimental results indicate that maximum face ventilation efficiency is achieved when the inby terminus of the line brattice is installed 5 feet from the face and at a distance less than one-third the entry width from the nearest rib. Analyses of data are based upon the ability of a face ventilation system to dilute methane in the immediate face area.

Jan 1, 1969

By J Johansson, B Johansson

The mining industry needs to attract and recruit young talented people. An important task is, therefore, to create an attractive mining workplace that engages with, and motivates youngsters who are not particularly interested in working in the industry. This paper aims to illustrate a way forward for the mining industry to form healthy and safe workplaces honouring key components such as knowledge, skill, co-operation, continual development and acceptance of diversity. This is a way to create a vision of healthy and safe mining work. The mining industry must work towards zero vision; a future without accidents and hazardous environments. In this paper the authors discuss different aspects of an ‘attractive workplace’ and summarises lessons learnt in 26 statements dealing with safety, both physical and social work environments, and social responsibility. The authors hope these recommendations will provide some guidance for how attractive workplaces should be designed for future deep mining.The paper is based on lessons from two large European projects, a Swedish-Polish project: The Smart Mine of the Future; and a European Union project: Sustainable Intelligent Mining Systems (SIMS). One of the authors was the WP leader of health and safety in both projects.CITATION:Johansson, J and Johansson, B, 2017. Attractive workplaces in future underground mining, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 99–102 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

The original JKMRC AG/SAG mill model was developed over 30 years ago and has been upgraded a number of times since then, with the current published version being the Variable Rates model that is now over 15 years old. Since this model was developed further enhancements have been derived, some of which are applied in-house and some which have yet to be incorporated. The published and the commercially available model in JKSimMet is currently undergoing a comprehensive overhaul with a vastly extended data base for model evolution and validation. Improvements developed within the AMIRA P9 project, in-house development and a number of collaborative projects, are being incorporated into the upgraded model structure. Enhanced capabilities will include: power-based breakage rates scaling; a far wider mill filling range (from 10% to 40%) that exhibits peak in throughput as mill filling increases; higher ball loads; improved pebble discharge function; improved slurry discharge function incorporating important mill design and operational influences; and the new size dependent breakage function. The model will also be able to accommodate some influence of liner design and multi-component ores (blends of hard and soft components). This upgrade is still a work in progress but substantial changes have been made to date. This paper presents some of the new improvements and their influence on the predictive capability of the model.

Jan 1, 2012