Search Documents

By P. U. W. Appel

Despite the very large offshore Exclusive Economic Zone (EEZ) area of Greenland (in excess of 2 mill. km2) virtually no work has been carried out on marine minerals on the ocean floor. Apart from a single reconnaissance survey by a mining company, major activities have been those of oil companies exploring the West Greenland shelf in the early seventies. The West Greenland shelf and its extensions is the most obvious area for year-around accessability when looking for marine mineral deposits. So far, only one onshore placer deposit has been found - ilmenite deposit near Thule, NW Greenland, whereas a gold placer in South Greenland presently is being evaluated.

Jan 1, 1988

By T. Ruben

Micropiles have been used for the last forty years to strengthen building foundations. This article gives information about the technology and capacity of micropiles.

Jan 1, 2000

By H. Antrekowitsch

The decreasing quality of the input materials in copper recycling leads to a higher content of impurities in the anode copper. An improvement of the pyrometallurgical refining process is therefore necessary to produce high quality anodes for the copper refining electrolysis. The behaviour of the most important accompanying elements (e.g. nickel, tin, lead, zinc etc.) at different reaction conditions has to be investigated in order to improve the metal/slag reactions as well as the vaporisation by selective oxidation in the anode furnace. Therefore the thermodynamic conditions like reaction order and the activity coefficients at the copper refining process have to be known for the optimisation of this technique. Additionally the interaction between different elements has been investigated as a function of the temperature, the content of the elements and the slag composition especially for nickel. These investigations were done at the Christian Doppler Laboratory for Secondary Metallurgy of Nonferrous Metals.

Jan 1, 2005

New York Meets first Wednesday after first Tuesday of each month. DAVID H. BROWNS Chairman. JOHN H. JANEWAY, Vice-Chairman. F. E. PIERCE, Secretary 35 Nassau St., New York, N. Y. P. A. MOSMAN, Treasurer. LEWIS W. FRANCIS. BENJAMIN B.. LAWRENCE. Boston Meets first Monday of each winter month. HENRY L. SMYTH, Chairman. ALFRED C. LANE, Vice-Chairman. HENRY A. WENTWORTH, Secretary-Treasurer, 60 India St., Boston, Mass. A. H. EUSTIS, F. G. STANTIAL. Columbia Holds four sessions during year. Annual meeting in September or October. STANLY A. EASTON, Chairman. FREDERIC KEFFER, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. D. C. LIVINGSTON, FRANK A. ROSS.

Jan 5, 1916

Reduce the number of accidents caused by slips and falls from large mining equipment. Approach A powered lift was developed that provides operators with a safer way of getting on and off large machines. How It Works The powered step is designed to lift personnel and materials to working levels on large machines. It eliminates hazardous blind steps and makes it unnecessary to climb on irregular surfaces made slippery by mud, ice, snow, and accumulations of grease. The step is powered by a self-contained electric/hydraulic unit which is connected to a vehicle's auxiliary power supply. When in the "down" position, the step rests about 15 inches above ground level. When the power unit is activated with an electrical switch located on the step, a Single cylinder attached between two lifting arms smoothly lifts the step. In conjunction with the lifting motion, a linkage and bearing arrangement on the mounting end of the lift arms causes the step to rotate towards the machine, so that the step moves in an arc from ground to platform level. When the machine Is operating, the step is automatically locked in the "up" position, protecting it against any damaging contact with obstructions. The step is lowered by activating a pressure release solenoid. An in-line orifice controls downward speed and prevents free fall. On most machines, additional control switches are conveniently located at ground level and in the operator's cab. Visual alarms and machine interlocks are provided where necessary to prevent machine operation when the step is In the "down" position. The powered step can be easily adapted to any type or model of large machinery.

Jan 1, 1981

By M. G. Driessen, H. E. Criner

Maurice Rey—The influence of cyclone diameter upon the fineness of separation is an important point which, however, cannot be discussed adequately if the injection pressure or the rate of flow are not specified. Perhaps some light can be thrown on the matter by using the formulas derived by Dahlstrom. Let us consider several geometrically similar cyclones where the apertures e and b are equal and proportional to the diameter D and which are operated with the same pressure drop. Eq 8 of Dahlstrom's paper can be written: Q Q = K D'. " or. if F is constant: Q = K D18 K is a constant of proportionality. Introducing this value of Q in eq 13 gives elimination efficiency = K D ,41 Elimination efficiency, in the terminology of Dahl-strom, means the diameter of particles, in microns, which divide equally between the underflow and the overflow. This denomination is regrettable and it would be preferable to call it diameter of separation or characteristic size or any other name connoting a size rather than an efficiency. Whatever the name used, the above equation shows a slow increase in the fineness of separation when the diameter of the cyclone decreases. For example, if a 14-in. cyclone gives a 400-mesh separation (37 microns), geometrically similar cyclones, having the same pressure drop will give separations at the sizes shown below.

Jan 1, 1951

By R. G. Jones

At its peak in the 1970s, South Africa was responsible for around 80% of global gold production and, according to the US Geological Survey, it still has the largest share of gold reserves - as well as 90% of the world's platinum. But, in January 2015, gold production reached a new monthly low, generating 87% less than it did in January 1980, and South Africa is now the world's sixth ranked gold producer. What next for African gold?

Jun 1, 2015

By W. S. Dyer

The lignite deposit at Onakawana on the Abitibi river is of particular interest at the present time, since the Ontario Government has recently decided to proceed with the extension of the Temiskaming and Northern Ontario railway to James bay. Forty-five miles of steel will be laid this year to the crossing of the Moose river. This will cross the lignite field. It has been known for many years that lignite occurred in the Moose River basin, but it was not until drilling was commenced at Blacksmith rapids (or Onakawana, as the camp is now known) in June, 1929, that a seam of economic thickness and extent was found. Early in 1929 the Ontario Legislature voted $25,000 for the carrying out of a drilling programme in the Moose River basin. This came as a culmination of two summers' exploratory work by the Geological Branch of the Ontario Department of Mines, and as the result of a report which said; in effect, that further information concerning the mineral resources of the basin could only be obtained by drilling, and that such a drilling programme was well worth while in order to establish once for all whether lignite, fire-clay, or oil or gas did or did not exist in economic quantities in the region.

Jan 1, 1930

By J. M. Mutamansky

"Coal mine dust research throughout the world has been stimulated by the recognition of its importance in the development of coal miners' diseases, particularly coal workers' pneumoconiosis (CWP). A historical look at the problem and the present state of knowledge in this area of importance to the worldwide coal industry is presented. A summary of progress made in this area is provided and some research ideas for the future are discussed.1. INTRODUCTIONI thank Dr. Yong Won John, President of the Korean Institute of Mineral and Mining Engineers, for his invitation to address the International Symposium on Coal Mining and Safety. This presents me with an interesting opportunity to take a broad look at the research in coal mine dust and where we are going. From this broad perspective, we can all view the progress and problems that are apparent in the present state of knowledge of coal mine dust. One important element in the review of coal mine dust research and its role in miners' diseases is that of its history. The existence of diseases attributed to the mine atmosphere is often traced back to Pliny the younger in the first century A.D. His work on natural history mentioned observed human effects attributed to mine fumes and vapors. However, the subject of the effects of dust in the mine was not mentioned in published literature until 1556 when Agricola discussed the ailments of miners in his day (Seaton 1975).For many centuries, many medical ailments of the lungs were often categorized together and distinct diseases were often not recognized until more modern times. The ability to distinguish different lung diseases was limited until the discovery of X-rays in 1986. Nonetheless, Zenker in 1866 applied the term pneumonokoniosis to any disease where dust gathers in the lymphatic depots of the lungs. This term was changed to pneumoconiosis in 1932. While pneumoconiosis was defined in the 1800s, scant attention was paid to control of miners' diseases until recent decades. The first attempt to control disease through control of the mine atmosphere has been attributed to the South Africans who instituted a silica control in 1910 (Drinker and Hatch 1954)."

Jan 1, 1989

By M. Fafard, D. Picard, J. -F. Bilodeau, G. Soucy

To simulate adequately the behaviour of a Hall-Heroult electrolysis cell, a finite element model must take into account the properties of each material. However, it has some lacking knowledge on the mechanical behaviour of materials, like the long-term visco-elastic (creep/relaxation) behaviour of cathode. A three-dimensional model is then proposed in this paper and will be ready to be implemented in the finite element code FESh++. The model was developed using the three-dimensional model based on thermodynamic of irreversible processes where the choice of the internal variables is based on a phenomenological approach. All parameters of the model are represented by constant constitutive tensors and the temperature and chemical dependencies are taking into account through scalar functions multiplying the constant constitutive tensor. The goal of the first part of this project was to determine the parameters of the threedimensional visco-elastic model at the reference state (virgin material at ambient temperature) of three different cathode materials. This paper presents the theoretical model and the results of creep tests at ambient temperature for the semi-graphitic carbon cathode.

Jan 1, 2006

By Raymond B. Ladoo

"The talc and soapstone deposits of Vermont have been worked more or less continuously for nearly 100 years, but all of the early efforts seem to have been directed toward the production of slabs for foot warmer, and other similar uses. Altho soapstone of good quality occurs at several places, much of the material first utilized was really talc and was not massive enough to be cut successfully. The grinding of talc in Vermont seems to have commenced in about 1902 and has shown continuous growth since that time. Statistics compiled by the Geological Survey in Mineral Resources of the ,United States show that the production of talc in Vermont has increased, from 8,978 short tons valued at $65,525 in 1905 to 93,960 short tons valued at $625,150 in 1917. Until 1917, New York was the leading producer in both tonnage and value with Vermont second, but in 1917, Vermont took the lead in tonnage produced, although not in value, with a production of over 47% of the total tonnage produced in the United States and over 35% of the world's pro-duction. This increase in production will probably be continued, though possibly at decreased rate, for the reserves of talc In Vermont are large.Active talc mines and mills in Vermont are found in four districts: Chester, Windsor County; Rochester, Windsor County; Waterbury, Washington County; and Johnson, Lamoille County, These mines and mills are distributed as shown in the following table:While there are a great many other known deposits of talc and soapstone in Vermont, some of which have been worked, those listed above are the only ones which have survived and are producing on a commercial basis. The closing down of many mines and quarries, for example, those at Perkinsville, Stockbridge, Reading, Cavendish, and Athens, has been attributed to several causes. Of these causes the most important seem to be exhaustion of the deposit, poor grade, long haul to the railroad, poor management due to lack of knowledge of mining methods and failure to consider talc mining strictly as a business proposition. The companies which are now operating with greatest apparent success are those which have realized the present and future possibilities of their industry, and have invested sufficient capital in both equipment and personnel to establish their companies on a firm business basis."

Sep 1, 1919

By Thomas P. Dowling

With the increased usage of AN/FO type blasting agents and the introduction and development of non cap sensitive slurries, water gels and other types of blasting agents, proper initiation and boostering of these insensitive materials has become a most important aspect of every blasting operation.

Jan 1, 1981

By J. W. Leonard

This expanded and more detailed supplement to earlier published work1 is offered as a means to demonstrate the high empirical correlation which exists between the readily measured coal bench scale test parameters of volatile matter (d & a.f.), Hard-grove grindability index (HGI), Koppers cone bulk density (BD) and pulverization level (% passing a 1/8-in. screen) to the less readily measured full scale coke stability index. Thus, Fig. 1, 2 and 3 represent the correlated test data contained in Tables I, II and III respectively. Ninety-six coals are correlated so that 97% of the resultant cokes fall within two points and 100% fall within three points of the actual tested coke stability indices. The main generalizations which can be drawn from the correlation of these coals are as follows: 1) The coke stability indices for higher bulk density coals (46.0 BD to 50.6 BD) appear to be largely influenced by differing combinations of factors for coals above and below a pivotal point of approximately 36% to 37% volatile matter. Below this pivotal volatile matter coke stability index appears to be influenced largely as a result of changes to the coal volatile matter and pulverization level. While above this pivotal volatile matter coke stability indices appear to be dependent on the coal hardness, as measured by the HGI, and to some extent upon coal volatile matter. Pulverization appears to have little influence on the coke stabilities of the harder coals (52 HGI to 58 HGI) of greater than 36% to 37% volatile matter. 2) The coke stability indices for lower bulk density coals (41 BD to 45.9 BD) appears to be largely influenced by changes to coal volatile matter and pulverization level for softer coals above approximately 58 HGI. 3) The main empirical observation to be drawn from these results is that for coals above approximately 36% to 37% volatile matter the quantities of hard and soft constituents as measured by the HGI are important when defining coal rank for correlation to the coke stability index.

Jan 1, 1965

By J. L. Havenga, L. J. van der Walt, J. T. Nel, H. Bissett

"SynopsisNew technologies used to manufacture high-quality components, such as direct laser sintering, require spherical powders of a narrow particle size distribution as this affects the packing density and sintering mechanism. The powder also has to be chemically pure as impurities such as H, O, C, N, and S causes brittleness, influence metal properties such as tensile strength, hardness, and ductility, and also increase surface tension during processing.Two new metal powder processes have been developed over the past few years. Necsa produces zirconium powders via a plasma process for use in the nuclear industry, and the CSIR produces titanium particles for use in the aerospace industry.Spheroidization and densification of these metal powders require remelting of irregular shaped particles at high temperature and solidifying the resulting droplets by rapid quenching. Spherical metal powders can be obtained by various energy-intensive methods such as atomization of molten metal at high temperatures or rotating electrode methods. Rapid heating and cooling, which prevents contamination of the powder by impurities, is, however, difficult when using these methods for highmelting- point metals. For this reason plasma methods should be considered.Thermal plasmas, characterized by their extremely high temperatures (3000–10 000 K) and rapid heating and cooling rates (approx. 106 K/s) under oxidizing, reducing, or inert conditions, are suitable for spheroidization of metal powders with relatively high melting points. Thermal plasmas for this purpose can be produced by direct current (DC) plasma arc torches or radio frequency (RF) inductively coupled discharges. In order to obtain chemically pure spheroidized powder, plasma gases such as N2, H2, O2, and CH4 cannot be considered, while Ar, Ne, and He are suitable. Neon is, however, expensive, while helium ionizes easily and it is therefore difficult to obtain a thermal helium plasma at temperatures higher than 3000 K. Therefore argon should be used as plasma gas. Residence times of particles in the plasma region range from 5–20 ms, but this is usually sufficient as 7–8 ms is required for heating and melting of titanium or zirconium metal particles in the 30 µm size range at 3500 K. In this study the melting and spheriodization of titanium powders was investigated by DC non-transferred arc and RF induction plasma methods. The powders were characterized before and after plasma treatment by optical microscopy and scanning electron microscopy (SEM) to observe if any melting or spheroidization had occurred."

Jan 1, 2015

By P. D. R. Maltby

"With the narrow vein structure of Nova Scotia gold deposits, selective mining is rarely possible and mill heads will be too low (below 0.10 oz per ton of gold) to support a conventional mill of up to 1000 ton per day capacity at present gold prices. The recent operation of a small 100 t.p.d. mill at Cochrane Hill using fine grinding - leaching - filtration supported this assertion. Milling costs exceeded $25.00/ton of feed mainly due to high capital, labour and maintenance costs.Accordingly, since 1981, efforts have been directed towards the development of a cheap gold extraction process in terms of both capital and operating costs. The main criteria is to produce gold below US $200 per oz including all administration, mining and process stages. This paper describes such a process development for Cochrane Hill. LOCATION AND HISTORY OF THE PROPERTYThe Cochrane Hill property is located about 8 miles North of Sherbrooke, N.S. on highway No. 7. Sherbrooke is about 180 miles east of Halifax. Gold was originally discovered at Cochrane Hill in the 1860's. Early work consisted of trenching. In the 1930's a small shaft was sunk to about 80 feet and some tonnage treated using a stamp mill with gravity concentration of gold.Northumberland Mines Ltd. acquired a 70% interest in the property in 1977. Subsequent drilling indicated a potential zone of gold mineralization with a drill-indicated tonnage of one million tons having a grade of 0.07 ounces per ton of gold (all high assays cut to 1 oz) down to a depth of 300 feet recoverable by open pit mining methods. In broad terms, the goldbearing zone is about 50 feet wide and 800 feet long and dips at about 70°."

Jan 1, 1984

By G. De Gregoriis, G. E. da Mota, H. P. Dias, J. E. M. Blasques

In recent years, like many other smelters around the world, Albras has been increasing line current. The necessary adjustments to the work practices and process variables need to be made on all potlines, which in this case means on 960 cells at the same time. It was a challenging task to adjust the process parameters to the new amperage. In July 2003 potlines 2, 3 and 4 were running at 1 73 kA and the goal at that time was to reach 180 kA. Preliminary trials with 180 kA were performed on a group of 10 boosted cells on potline 3 in order to investigate possible operational problems. It was decided to increase the amperage in three steps accompanied by continual evaluation of the state of the process. In July 2004 the target of 180 kA was achieved with good operational results. This paper presents the overall results, the parameter adjustments made during the amperage increase in the booster group and how the increase was implemented on the other potlines.

Jan 1, 2006

By S. Bhattacharyya

"Coal bearing rocks are low in strength and have geological discontinuities and moisture sensitivity. Roof and rib falls have been a major cause of fatalities in underground coal mines. Mine engineers design ground control plans for regulatory approvals. A number of tools are available from the National Institute for Occupational Safety and Health to design and assess these plans. Quite often there is not enough geotechnical input information available and databases are used. The Appalachian coalfields have extensive scientific studies to provide reliable regional inputs. Coal mines in the western United States and Canada have different geological and geotechnical conditions, and less available data. Use of inappropriate inputs in the tools like Analysis of Retreat Mining Pillar Stability, Analysis of Longwall Pillar Stability, and Analysis of Roof Bolt Systems may result in unsafe designs or over conservative designs. The tools are convenient but thorough understanding of the inputs, calibration with local test results, and operating experience are important for effective designs. The current paper contains examples of difficulties faced during mine planning using the above tools. INTRODUCTION Sedimentary rocks hosting coal are low in strength. Scientific studies have placed the uniaxial compressive strength (UCS), triaxial strength, tensile strength, and shear strength of sandstone, shale, siltstone, and claystone in lower range of strength among engineering materials (1). Coal bearing rocks are most often weakened by the presence of faults, folds, slickensides, bedding planes, fractures, and other geological discontinuities. The host rocks and coal are often moisture sensitive. The geological discontinuities allow water to enter the strata from surface and underground sources. This combination of low strength, structural weakness, and presence of water results in difficult ground control situations for the coal mines. Roof (2) and rib falls have been a major cause of fatalities in the U.S. coal mines. Modern underground coal mines necessitate wide entries to accommodate large production equipment. The gate roads, section entries, and the mains entries of a highly productive coal mine are as wide as twenty feet (6.1 m). The actual intersection width is nearly thirty feet (9.1 m). Adequate ground control is a key to maintain safe production in such mines. Mine engineers and their consultants routinely submit ground control plans to the regulatory authorities. While working out the necessary roof control system the mine engineers are required to demonstrate the adequacy of the proposed system. There are multiple ways to demonstrate this. Some engineers use traditional load calculation approach of roof bolts (3). Some engineers use numerical methods. Yet a large number of professionals resort to a suite of ground control design software offered by National Institute for Occupational Safety and Health (NIOSH) commonly referred to as “NIOSH Ground Control Toolbar.” These software tools are free and easy to download from NIOSH website. The software included in this package are: Analysis of Longwall Pillar Stability (ALPS), Analysis of Retreat Mining Pillar Stability (ARMPS), Coal Mine Roof Rating (CMRR), Analysis of Roof Bolt Systems (ARBS), Analysis of Horizontal Stress Effects in Mining (AHSM), Analysis of Multiple Seam Stability (AMSS), Analysis of Retreat Mining Pillar Stability - Highwall Mining (ARMPS-HWM). These tools are relatively simple to install and use in planning and designing coal mines and prospective coal mines. They accept a number of geotechnical inputs which are collected from either an existing mining operation or from exploratory boreholes. In the absence of necessary input parameters, the programs use default values which are drawn from databases of geotechnical properties built by NIOSH."

Jan 1, 2015

By M. C. Fuerstenau, D. W. Fuerstenau

Long-Chained aliphatic amine salts have been used for the separation of sylvite (KC1) from halite (NaC1) by flotation. It is puzzling how these two minerals, which are so similar chemically and crystallographically, can be separated by this method. Gaudin as postulated that the difference in floatability of halite and sylvite with salts of primary amines depends on ionic size: In the case of amine flotation, the cation would attach itself to the chloride. I have a speculation there, which I cannot prove, that the ammonium group, that is the –NH3 group in the amine, floats potassium chloride because the dimensions of this group as it has been measured in other compounds is almost identically the dimensions of the potassium ion, quite different from the sodium ion, and so it fits where potassium had been, in place of it and not attached to it.

Mar 1, 1956

By Rajib K. Mohapatra, K. Vizaya Kumar

In any manufacturing organization internal logistics plays a vital role in improving and maintaining the productivity. In Ferro Alloys manufacturing organization where there is huge input of raw material in terms of ore, reductants and variety of fluxes amounting to about four times of the mass of alloy produced need to be handled from yard to furnaces , internal logistics requires utmost attention. Any deviation or mismatch between stock and requirement will affect furnace operation. Though the activities are being outsourced by most of the organization, these require close monitoring. This communication presents an optimization model which can work as a ready reference for the manager to decide upon the material quantity and the furnace to be fed with an objective of minimizing the cost of handling and zero production loss.

Jan 1, 2007

By R Wilson, R Williams, B Freeburn

McLanahan RSS14x50 scrubber screens have individually processed over 50 Mt of Pilbara iron ore. The first stage of separation in these plants with abrasive, high specific gravity, large lumps is an extremely arduous duty with high wear rates. With the Scrubber Screen layout this occurs in the attached trommel section. The initial supply of the replaceable trommel panels were of steel-backed rubber with a service life of approx. six weeks. Site Personnel established a goal of 26 week wear life in conjunction with 100 per cent reliability and while field trials were undertaken using a variety of hardened and cast steels that demonstrated wear life to the nominated requirement some unpredicted failures still occurred. With a long evaluation time and challenges to create repeatable conditions with field testing, a purpose built test unit was designed and constructed to allow controlled evaluation of a number of materials and designs. During 2016 tests were conducted with eight different materials, of varying thickness to simulate impact conditions and a number of aperture profiles to evaluate both impact and abrasion effects. From these results two designs were selected for full scale implementation to confirm the nominated goals. This paper will present details of both testing procedures and results of all materials, as well as conclusions of successful field implementation.CITATION:Wilson, R, Freeburn, B and Williams, R, 2017. Trommel panel development for iron ore applications, in Proceedings Iron Ore 2017, pp 251–256 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017