Search Documents

By C. O. Hawk

Distillable oils derived from coal were desulfurized and hydrogenated at 2,500 psig in a two-step vapor-phase catalytic operation to give a product rich in saturated cyclic hydrocarbons. The first step was mainly a desulfurization at 400 C, the second a saturation at 300 C. One of the oils used as feed stock was from low-temperature carbonization of a bituminous coal, the other was from the liquid-phase hydrogenation of coal in the Bureau's pilot plant. The product from the saturation step was distilled to remove the light ends and high-boiling residue and to recover a fraction having acceptable properties with respect to heating value, density, freezing point, viscosity, and boiling range according to specifications suggested by the Air Force for ultra-high-speed aircraft fuel. Quantities of the fuel fraction available were too small for the thermal stability test approved by the Air Force. The experiments, performed on laboratory scale, comprised mostly a study of the effect of varying the oil feed rate (at constant oil-to-hydrogen ratio) on the yield of the desired fuel fraction. The yield of the fuel fraction made from low-temperature carbonization oil was a little more than 1 percent of the weight of coal carbonized; that from coal-hydrogenation oil was about 12 percent of the weight of coal hydrogenated. A few attempts to do both desulfurization and saturation in one operation with sulfur resistant catalysts, developed for vapor-phase hydrogenation or hydroforming, were unsuccessful. By leaving the low-boiling ends in both feed stocks to desulfurization, another product was obtained: a low-sulfur aromatic cut boiling below 200 C. This material would be suitable as a solvent or a chemical raw material.

Jan 1, 1965

By D. R. Arnold

Discussion of the above paper by D. R. ARNOLDt This paper is the result of an excellent piece of work performed as a service to hyUrometallurgy in general and to the South African uranium industry in particular, and the authors are to be congratulated, Authors' reply Dr Arnold is correct in saying that the present Senbrix resins, which are based on the experimental heavy resins first developed at the National Institute for Metallurgy (NIM), need not necessarily show the same poor performance with respect to cobalt poisoning as the NIM prototypes. Oceanology International The next 01 World Conference is to be held Brighton, England, from 2nd to 7th March, 1980. The programme will concern technical advances in the offshore oil and gas industries, and is expected to include 140 papers from 20 countries.

Jan 1, 1979

By Karl Kure, Anders M. Heltzen

Mixtures of prilled ANFO and 0,5 - 3 mm polystyrene balls are interesting substitutes to the tube charges or other types of reduced explosives or detonation fuses. Experiments have shown detonation ability even of a mixture of 95% bolt polystyrene balls and 5% ANFO. The gas and shock energy in the mixtures decrease proportional with the content of polystyrene. The detonation velocity shows higher values than expected for mixtures with more than 50% (vol.) ANFO.

Jan 1, 1980

By Jeremy G. Kress

We propose the discrete element method (DEM) as a complimentary alternative to analytical solutions and FEM models for the analysis of pile response. DEM is a novel approach to the engineering design of deep foundations which can be used to provide insight into the mechanics of soil-soil and soil-structure interaction. It is common to use analytical, empirical, and semi-empirical methods to predict pile behavior, where if granular properties, pile length, or load orientation change, then significant adjustments are made in the design sequence. DEM provides a more uniform approach in granular soils. Based on constitutive force-displacement relationships and laws of motion in rigid and elastic bodies, few changes must be made for a wide variety grain types, pile types, embedment, and load orientation. Preliminary results for simulation of a single pile are qualitatively consistent with results from conventional design procedures and also provide significant information not available from other analyses (e.g., local information about interface failure during shear). Importantly, these analyses are portable to a variety of pile types and installation procedures, which may not be the case for empirical approaches. Given consistent increases in computing power and rapid advances in model speed and sophistication, the DEM should prove to be a robust method for design and the analysis of pile response in granular soils.

Jan 1, 2010

By J. Diaz

"Antioquia region, in Colombia, is considered one of the areas with the highest mercury contamination in the world due to its use in gold recovery through artisanal mining, emissions to the environment between 100 and 150 tonnes of mercury are estimated by year. Therefore it became necessary to develop a project in which it was proposed aim to empower traditional artisanal mining community, or in different areas, such as gold mining in the region of Antioquia, in the implementation of safe mining practices and environmentally sustainable, from the introduction of clean technologies, in order to prevent or mitigate the impacts generated by traditional mining on the environment and the communities involved. In order to achieve this training to traditional mining community developed and technical visits to artisanal mining were performed in order to optimize operating processes and promote safe mining practices. In the project more than 1400 artisanal miners were trained.INTRODUCTION In the developing world, a combined 30 million individuals extract more than 30 different minerals using rudimentary techniques. Gold is the preferred mineral extracted by artisanal operators due to its high unit value and its market price, which has increased almost sevenfold over the last decade (Veiga et al, 2014). The artisanal gold mining sector in Colombia has 200,000 miners officially producing 30 tonnes Au/a. In the Northeast of the Department of Antioquia, there are 17 mining towns and between 15,000 and 30,000 artisanal gold miners (M. Veiga, 2010) (Upme, 2014). This production, however, has caused environmental problems, including high levels of river siltation and mercury pollution (Veiga et al, 2014) (UPME, 2007) (Cordy et al., 2013). The mercury contamination in Colombia by artisanal gold mining has been recognized by a number of researchers and local authorities for over a decade estimated that the annual mercury emissions from artisanal gold miners in Colombia in 2007 were between 50 and 100 tonnes, however given recent gold value increases and gold rush activity, current mercury emissions are likely much higher. Colombia is likely the world's 3rd largest source of mercury emissions from AGM after China (240 to 650 tonnes of Hg/a) and Indonesia (130 to 160 tonnes of Hg/a) (Telmer and Veiga, 2008) and is the world's highest per capita mercury polluter (M. Veiga, 2010)."

Jan 1, 2016

By J. N. Hobstetter, J. J. Becker

Slip lines in deformed copper single crystals exhibit very pronounced cross-slip and clustering if the stress axes are not too far from <100>. This orientation dependence seems to persist whether or not attempts are made to reduce the bending constraints of ordinary mechanical tests. THE purpose of this paper is to report some microscopic features of the plastic deformation of copper single crystals. The material used was OFHC copper obtained from the American Brass Co. Single crystals about 3 in. long and 5/16 in. in diameter were made by lowering graphite crucibles containing this copper out of the hot zone of a vertical tubular furnace at a rate of 1 1/4 in. per hr. The furnace atmosphere was nitrogen. The orientations of the crystals were determined by the back-reflection Laue technique.&apos; The X-ray spots usually indicated a slight lineage structure of not more than a degree or two. The crystallography of slip is discussed in Schmid and Boas.&apos; The terms classical slip, cross-slip, and conjugate slip are used here with the same meanings as in ref. 3. Compression Specimen 17 (Fig. 1) was selected because the resolved shearing stresses on eight slip systems dif- fered at most by a factor of 1.2. It was hoped that in this situation such effects as cross-slip might be made more prominent. Two intersecting planes parallel to the stress axis were ground on the crystal, using optical abrasive on a lead lap. The large plane was approximately perpendicular to the plane of the axis and the primary slip direction. Its exact orientation was determined by X-ray. The smaller made an angle of 49" with the larger, measured by reflecting a small light source. The specimen was etched with nitric acid until its diameter had been reduced 0.010 in., and then was given a metallographic polish and very

Jan 1, 1954

By John F. Blandy

Although the question of the "waste of anthracite coal mining " has been so frequently discussed, and a committee was appointed at the first meeting of this Society to consider and report upon the subject, still but little progress seems to have been made in arriving at a conclusion as to how it ran be reduced. That committee made a preliminary report at the August meeting, 1871, in which it divided the question into three parts, namely: Waste in mining, in preparing for market, and in transportation. I shall not here refer to the first item, as so much depends upon the peculiar features of each separate mine, and the skill of those in charge; but in reference to the second, that of preparing the coal for market in breaker and screens, I wish to make some remarks. There is no use considering the question, whether the coal should be broken up to suit the fancy of consumers; all miners are satisfied that it should not be, but the consumers decide that they want it that way, and the miner must submit, and simply utter his maledictions upon the head of the man who first suggested a breaker or screen, if that is any consolation to him. What is called waste in this process of preparation, is the dust and fine coal, which results from the breaking and screening, and, as we all know, this is a very important percentage of what passes from the slope to the top of the breaker. Now, if this dust and fine coal can be utilized—the slate which is picked out is not to be taken into consideration as waste—then we get rid of this item entirely. There is no question in my mind that this article can and will be used as a steam generator at least, and I think, therefore, that in depositing

By Jianmin Qin, Raja V. Ramani

In this paper, the results of a research study on airborne dust transport in a full scale simulated longwall face are presented. The simulated longwall face was set up in the Lake Lynn Laboratory mine of the U.S. Bureau of Mines to conduct experiments under controlled conditions. The controlled parameters in the experiments were the dust dispersion rate, dust size distribution, density of the dust, air velocity, and the rate of travel of the dust generating source. The analyses of the experimental results on mass concentrations, particle size distributions, and real-time respirable dust concentrations are discussed. There are definite spatio-temporal trends between the location of the shearer, the concentration at any location in the face, and the dust generation rates. The size-consist and density characteristics of the source dust, the air velocity in the face, and the air leakage into the gobs all affect the concentration.

Jan 1, 1995

By Xinghua He, Shujing Zhu

"In this paper, the chemical composition, the content and the leachability of heavy metals in dredged sludge are tested and analyzed. It is shown that the leachability of Pb and Cr exceeds the leaching toxicity standard, and so the dredged sludge is considered as hazardous waste and must be solidified. The effect of solidifying the dredged sludge by the hydraulic ash-slag cementitious composites is studied, and it indicates that the heavy metals can be well immobilized if the mass fraction of the dredged sludge is appropriate. The heavy metals are immobilized within the hydraulic ash-slag cementitious composites hydration products through either physical fixation, substitution, deposition or adsorption mechanisms.IntroductionDredged sludge is classified as a hazardous waste because it usually contains concentrated heavy metals and chlorinated organic compounds, as well as soluble salts, and is also composed of very fine particles. Moreover, inorganic pollutants are typically associated with soluble compounds, which are, therefore, highly leachable from dredged sludge when dredged sludge is contacted by a liquid medium[l1. Thus, dredged sludge must be stabilized in order to reduce its environmental impact on the final disposal site. The frequent means of dredged sludge disposal used include(!) Chemical stabilization (2) acidic extractionChemical stabilization is translating mobile heavy metals into low dissolution and low toxicity form through chemical reaction. The commonly chemical medicaments are sodium hydroxide, soldium sulfide, thiourea, EDTA. But Zhao et al [ZJ found sodium hydroxide is not fit for Pb stabilization, the other three are effective, but the chemical properties of sodium sulfide are not stable, thiourea and EDTA are very expensive, and so it is very difficult to apply them. Moreover, because of the complexity of heavy metal conformation and dredged sludge composition, it is very difficult to find a cheap and prevalent stabilization medicament in point[31 ."

Jan 1, 2013

By Jim Henry

I would say mainly the cost. I showed only 3 cases. One of them was the one that Allen just described and there were two other cases. In those cases it was fairly easy to develop a solution using limited mobility grout to treat the soft soils suitable for the limited bearing pressures required by the structures. LMG readily provided a fairly reliable system for the foundation support at a reasonable cost.

Feb 10, 2003

By A. S. W. Kurny, M. Z. Huq

Bangladesh ilmenite is partially altered, containing pseudorutile, rutile and haematite as well as the predominant ilmenite phase. A typical analysis is 39.45% TiO2, 24.19% FeO and 33.0% Fe2O3. Reduction of the ilmenite by charcoal was found to involve two major reactions: conversion of pseudorutile into ilmenite and rutile, and change of ilmenite into metallic iron and rutile. The first, which was much the faster reaction, was responsible for an initial increase in ilmenite content with reduction time at lower temperatures. Apart from these two major reactions, rutile was reduced to lower oxides at 1 100 degrees C with a consequent decrease in its XRD peak height

Jun 19, 1905

Jan 1, 1926

By D. A. Koss, R. O. Gordon

Changes in the ultrasonic attenuation in steel specimens have been observed during tensile tests. Samples of AISI 1020, 1045, and 1095 steel quenched and tempered to a spheroidized condition have been used. Both attenuation and microstrain measurements fail to reveal preyield dislocation motion in the as-tempered specimens. Upon reapplication of the load to samples in the strain-aged condition there is a large preyield attenuation increase but no observable micvostrain up to 90 pct of the flow stress. These and other observed changes can be related to changes in the free disloca-tion density and the average dislocation segment length. The results show that the increase inflow stress in the strain-aged condition is caused by increased fric-tional stresses rather than by dislocation pinning. Strain aging is found to proceed through three distinct stages. The second of these follows the t2,3 law and is characterized by an activation energy of 20 kcal per mole. RECENT years have seen substantial progress in the understanding of the sharp yield-point phenomenon in metals; the influence of solute atom pinning of dislocations, of dislocation multiplication, and of the stress dependence of dislocation velocity on the stress-strain curve has been investigated. Evaluation of the relative importance of these factors in the various metals and alloys is not complete, however, because observation of the stress-strain curve alone is not sufficient to determine the yield mechanism. In the experimental study of the sharp yield point it would be desirable to be able to directly observe the dislocations in a bulk specimen. Ideally, the observations should be made during deformation because of the rapidity of recovery processes in lightly strained metals. While direct observation of dislocations under these conditions is not possible, certain physical properties sensitive to the dislocation structure can be observed while a test specimen is undergoing deformation. Of these properties, one of the most useful is the ultrasonic attenuation. The total observed attenuation, a, is due to a number of causes: acoustic diffraction, scattering by inhomogeneities in the structure, heat flow, magnetostriction, and dislocation damping. Satisfactory measurements of the absolute a are difficult to make because all of these factors cannot be evaluated in any given specimen, but changes in a due to changes in the dislocation contribution alone can be reliably observed by appropriate technique. Because dislocation damping is sensitive to small concentrations of long, free dislocation segments, observation of acoustic attenuation due to dislocations is particularly useful in the study of the early stages of plastic deformation. In the experiments to be described, acoustic-attenuation measurements have been made on steel samples as these were pulled through their yield in tension. While many details of dislocation-damping phenomena in the bee metals remain obscure, the main characteristics of this type of internal friction are established. At low strain amplitudes and at frequencies well below that of dislocation resonance (the conditions of these experiments) the dislocation contribution to a is given by1 where A is the density of freely oscillating dislocation segments, L is the average segment length, B is the damping constant for a moving dislocation, w is the frequency, O is an orientation factor, C is the dislocation line tension, and t is a numerical factor relating average segment length to the distribution of lengths. Because of its fourth-power dependence on L, a is highly sensitive to changes in dislocation free segment length such as might arise from unpinning, recovery, jog formation, or dislocation intersection. The above equation is not valid near the resonant frequency of dislocations, but the segment length in steel is believed to be much too short to cause over-damped resonance near 10 Mc; this will be discussed later. In the present experiments plastic-strain measurements with a sensitivity of 2 x 10-5 were also made during the early stages of loading in order to detect preyield strain. The general plan of the experiments is to observe

Jan 1, 1967

By N. Pradhan, B. K. Mishra, B. D. Nayak, B. K. Mohapatra, R. K. Mohapatra

"Present study is about use of a group of Iron[Fe(III)] Reducing Bacteria (IRB) to convert the goethite (a-FeOOH) present in the original lateritic Nickel ore to magnetite under an anaerobic condition and subsequently release the bound Co(III) and Ni(II) through leaching. The lateritic Nickel ore contains 0.8% Ni, 0.049% Co, 1.92% Cr, 0.32% Mn and 50.2% Fe. An anaerobic dissimilatory Fe(III) reducing bacterial consortium capable of using acetate as carbon source (electron donor) and lateritic ore as terminal electron acceptor, changes the initial light brown color of the ore to dark brown. The change in color is due to the conversion of goethite to magnetite, which was confirmed by XRD. When the IRB treated sample was subjected to both bioleaching and acid leaching, it shows a greater recovery of Nickel and Cobalt values as compared to untreated original lateritic Ni ore. Further a magnetic separation method was used to separate the magnetic part of the treated lateritic ore and subjected to acid- and bio-leaching for better recovery of Nickel and Cobalt.IntroductionIt has been known that micro-organisms have the potential to reduce metals but more recent observations have shown that a diversity of specialist bacteria and archaea can use such activities to conserve energy for growth under anaerobic conditions [12]. Natural Fe(III) oxides are high in surface area and are reactive [1]. Fe (III) oxides adsorb a wide range of metal cations and anions by complexation to surface hydroxyl groups [17], and function as the primary redox buffering solid phase in many sediments and subsurface materials [5].Recently a number of bacteria have been isolated based on their ability to use metal ions, including Fe(III), as electron acceptor under anaerobic conditions. These are capable of producing energy by coupling the oxidation of organic compounds to reduction of Fe(III). Iron[Fe(III)]-Reducing Bacteria (IRB) have been isolated and identified from a wide variety of environments including freshwater and marine aquatic sediments and submerged soil [8]. The biogeochemical cycle of iron is linked to those of the trace metals, as many trace metals coassociate with Fe(III) oxides or reduced iron phases (e.g., magnetite, siderite, or iron sulfide). IRB can utilize Fe(III) oxides as terminal electron acceptors for respiration [18]; thereby reducing all or a fraction of the solid. The reductive portion of the iron biogeochemical cycle in non-phototropic environments (e.g., sediments and subsurface materials) is driven by the direct enzymatic reduction of Fe(III) oxides to Fe(II) by dissimilatory iron reducing bacteria [13,14]."

Jan 1, 2009

By J. M. Barker

The concept of global-market access through transportation efficiency is a concept whose time has come. The basis of this approach is customer satisfaction—the higher the better. But beyond what seems almost too logical is the question of how to achieve this market access. All industrial mineral exporters face stiff competition. Factors include proximity of competitive industrial minerals and substitutes, pricing pressure, political and cultural differences, currency fluctuations, communication problems, trade finance restrictions, and transportation imbalances. The following discussion will focus on transportation activities in global competitiveness, but the producer with the larger offering of services will often make the sale, not necessarily the low-cost producer (Cook, 2002). Some key concepts for global-market access are “the market concept,” just-in-time delivery, quality retention, and global customer service.

Jan 1, 2003

By Teh-Yu Kao, Don J. Wood

With the increasing industrial use of the method of transporting solids by fluids through pipes, a better understanding of the basic mechanics of a solid-liquid pipe flow system is essential. In this study the phenomenon of incipient motion of solid particles resting in a sediment bed on the bottom of a pipe is investigated. Since a system would fail to operate at the designed solid-liquid flow condition if it was not capable of operating through the transient initial flow phase, information concerning the starting transient is of great interest. An objective definition of incipient particle motion, derived from energy considerations, is first proposed. Using this the critical state is defined to describe the flow condition during which a solid particle can at least temporarily escape the sediment bed and move in the liquid. Postulated also in this study is that the condition of incipient motion can be reasonably well predicted by a consideration of particle equilibrium in a direction normal to the pipe axis. The incipient condition is considered to occur at the instant the force between the bed and the particle, normal to the pipe axis, is zero. Experimental measurements of incipient conditions are obtained for water flowing through a horizontal pipe with sand sediment beds of different thickness. These are compared to predicted values with good agreement.

Jan 1, 1975

By I. J. Wu

China’s land area, comparable in size to United States or Canada, contains diverse geological environments and mineral resource potential. The diversity in geological environments is such that the potential for developing many world-class mineral deposits in China is good. However, China’s mining sector was not open to foreign investment until the1990s. The long-term prospect for Chinese resource development is attractive because of China’s enormous population and cumulative demand for minerals. Approximately 33 foreign mineral companies, including 11 major internationals, are to various degrees active in China. Chinese mining laws and regulations pertaining to joint ventures with foreign companies are, from the international investment prospective, evolving slowly, but positively. This positive trend is continuing under the current government reform process, which is moving China towards a freer market economy. Although improving the enforcement of relevant laws and regulations is an ongoing process, the environment for mineral investment and joint ventures is increasingly more accommodating to foreign companies.

Jan 1, 2000

By Jorge Olivari Ortega

"La plata fue un metal de apreciado valor para las sociedades pre-hispánicas -en tanto los mineros lo obtenían de forma pura y se beneficiaban como metales argentíferos. En ese sentido, el presente texto describe su historia y usos en las sociedades pre-hispánicas. La plata se encontraba en los filones hidrotermales, asociada a la argentita, un sulfuro de plata, y calcita, así como a diversos sulfuros y arseniuros de níquel-cobalto-bismuto. Asimismo, gracias a sus propiedades físicas como color, brillo y maleabilidad, se puede trabajar fácilmente y obtener bellos objetos zoomorfos (auquénidos andinos: llamas, alpacas y vicuñas) para los rituales de fertilidad del ganado."

Nov 1, 2016

In his paper, Sastry proposes the use of flotation methods other than the "conventional flotation!&apos; process as possible economical methods of removing mineral fines, The practice of Liquid/Solid separation employing microbubbles to assist or induce the flotation of suspended solids is common to both municipal and industrial waste- water treatment; and is also used as a separation step in some processing industries. The pretreatment (if any) of the stream prior to flotation, the source of the microbubbles, and the design of the separation vessel depend on the application. For example: a metal finishing plant would use an elaborate chemical conditioning scheme to precipitate metal hydroxides for removal by a dissolved air flotation unit operating in the effluent recycle mode, while some oily waste can be separated using a dispersed air flotation cell with no chemical conditioning. At the present time, the "conventional flotation" process employed by the mineral processing industry makes use of mechanical agitation and aeration to generate certain sizes and quantities of bubbles and to mix these bubbles with the pulp. Specific types of chemical conditioning are used to obtain the desired results. For the separation of mineral fines, the type of chemical conditioning, bubble generation and separation device needed to obtain optimum results will have to be determined through research. The point to be made is that while the principles of flotation separation can be applied to a wide variety of applications, the specifics of the flotation process may vary with each application. Sastry&apos;s paper has dealt with the many areas of research required to fully understand and utilize the flotation process for the beneficiation of mineral fines.

Jan 1, 1979

By A. A. Sadegh

A laboratory investigation was carried out on the characterization and beneficiation of sillimanite ore. Petrographic analysis indicated that the ore consisted of massive elongated sillimanite grains in a matrix of hematite, garnet, feldspar and silica. A procedure for estimating the percentage of sillimanite was developed using float-sink and magnetic-separation techniques. A liberation study was carried out to determine the level of size reduction required to achieve sufficient liberation while ensuring that gravity concentration techniques would be applicable. Laboratory testing was performed on the liberated ore to investigate the applicability of using wide-angle dense-medium cycloning to upgrade this ore. Initially, medium-only tests were carried out using various size distributions of magnetite and ferrosilicon as the dense-medium solids to evaluate the effects of operating conditions on medium segregation. Depending on the medium solids and operating conditions, either positive of negative differentials (difference between the relative densities of the underflow and overflow streams) were obtained. Based on these results, separation tests were performed to process nominal -1.2-mm sillimanite ore. The results indicated that sillimanite concentration could be obtained using a medium relative density that was much lower than would typically be used in a dense-medium cyclone separation.

Jan 1, 2007