Search Documents

By V. R. Spironello

The Bureau of Mines is involved in research directed toward the utilization of municipal solid waste. One of the primary objectives is the recycling of the magnetic fraction of municipal solid waste (raw refuse). This is consistent with one of the Bureau's goals, which is to minimize the requirements for mineral commodities by maximizing metals recovery from secondary domestic resources, In this investigation, cupola trials were made using combinations of refuse scrap with shredded automobile scrap under basic and acid slag practices. Furnace operating information and the behavior of alloying and tramp elements was obtained. The research showed that it is possible to utilize up to 60 percent refuse scrap in the cupola under basic practice and 30 percent under acid practice, Aluminum in refuse scrap, present in bimetallic cans, increased the recoveries of silicon and manganese charged to the cupola. Increased use of refuse scrap provided iron of lower sulfur. The alumina resulting from oxidation increased the slag volume. The aluminum and tin contents of the iron increased with increasing levels of refuse scrap in the charge. Lead was not a problem with respect to contamination of the iron. In basic practice, operation of the cupola was satisfactory since all slags were adequately fluid. In acid practice, operation became troublesome above the 45-percent level. Under both practices, the cupola iron melting rate decreased. Particulates in scrubber water and stack condensate samples contained lead, zinc, and tin, and the dust load increased. The tensile and transverse strengths of the iron produced under both practices are reported.

Jan 1, 1980

By Heath E, van Calsteren P, Turner S, McDermott F

U-Th isotope studies of recent volcanic rocks may be used to evaluate the depths and rates of melt generation beneath mid- ocean ridges and ocean islands. Island arc rocks exhibit a similar range in Th isotopes to that seen in both MORB and OIB, but while those with high (230Th/232Th) tend to have excess 238U, many of those with low (230Th/232Th) are in isotope equilibrium. The excess 238U is attributed to the preferential mobilisation of U in hydrous fluids from the subducted slab within the last 100,000 years, whereas the low Th isotope ratios in the higher-K arcs are primarily due to the introduction of subducted sediment. Preliminary results from mineral separates from lavas on Soufriere on the island of St. Vincent indicate that some of the minerals crystallised up to 50,000 years prior to eruption.

Jan 1, 1995

By Filippo Leoni, Wesley Schmutzler

"The LPV-111 East Back Levee Improvement Project lies along the Gulf Intracoastal Waterway (GIWW) in Orleans Parish of New Orleans, La., and is an essential component of the New Orleans Hurricane Protection System. The Hurricane Protection Office of the U.S. Army Corps of Engineers (USACE) attributed failure of the New Orleans East levees system to overtopping, erosion and subsequent breaching of LPV-111 along the GIWW, as well as other sections of flood protection during Hurricane Katrina in 2005. The existing levee suffered extensive damages from Hurricane Katrina, such that the USACE elected to provide earth stabilization and to rebuild the levee sections. Due to the adverse geotechnical properties of the foundation soils, the Corps deemed ground improvement necessary to stabilize the new levee and to limit its footprint. Wet Deep Mixing Method (DMM) was selected as the most suitable technology for this task.ChallengesDesign: This reach specifically protects East New Orleans and the Bayou Savage National Wildlife Refuge, the largest urban wildlife refuge in the U.S. and home to several threatened or endangered species of birds as well as many reptiles, amphibians and small mammals. The Corps chose DMM due to the sensitivity of the protected marshlands and because the method limits the footprint of the raised levees. The increase in the load bearing capacity of the treated soil significantly decreases the footprint necessary to attain the required height increase. This limitation required the new levee to have steep slopes, drastically increasing the surcharge on foundation soils characterized by overall poor geotechnical properties (soft clays and peats). The design also considered the increased horizontal stresses on the levees due to the extreme storm surges during a hurricane.The design of the 1.6 m diameter (5.25 ft) DMM elements called for overlapping them to form a double auger element that formed buttresses perpendicular to the levee alignment. The contractor installed the buttresses at a maximum on center spacing of 4.7 m (15.5 ft). One additional double auger DMM element was midway between consecutive buttresses at the centerline of the levee to further help prevent settlement (Figure 1)."

Jan 1, 2013

By D. A. Dahlstrom

With today's high energy costs per million BTU's, far greater emphasis is placed on increasing thermodynamic efficiency in the use of energy. America has long since discarded its previous golden age of "low cost energy" in the past ten years. Energy costs are now a very significant percentage of operating expense in industrial operations. Public utilities have felt the same influences of increasing costs in energy for the generation of electricity. Not only has the input energy expense increased seriously, but as pointed out by Blackmore in a paper, fuel costs were 53.4% of the total operating costs for American Electric Power Company.

Jan 1, 1983

By Mark K. Larson

A constitutive model for rock interfaces based on the principles of static fatigue is proposed. The model is applicable to weak rock or joints with cohesion. Friction and dilation are decreased as plastic work increases. At equilibrium, the creep time increases by one time-step interval, and interface cohesion at each node decreases according to a power function. A constant-load, direct-shear simulation showed that the model is cap- able of mimicking constant-rate and tertiary creep and predicting failure. Tests on core from a coal mine showed constant-rate and, sometimes, tertiary creep, but also weak transitory creep. The cohesion deterioration function may need modification to simulate primary-phase creep. If model parameters are known for a site, the model can predict the onset of tertiary creep and failure. Such predictions can help engineers make better entry design and support decisions, which will reduce the likelihood of roof falls and increase safety for underground miners.

By E. Don Dilling, W. F. Holbrook, Lloyd R. Michels, James W. Pennington, Dwight L. Harris, Wm. F. Hergert, Cyrus L. Blogett, H. A. Doerner, Ernest A. Reige

"IntroductionA process for production of magnesium by carbothermal reduction was developed at Padentheirm, Austria, by the Austro Americanische Magnesit Corporation& an independent investigation of this and other processes was started in 1937 by the Bureau of Mines at Pullman, Wash., with the cooperation of Washington State College. 10/ A preliminary study of the Radentheirm pro¬cess, as revealed by the meager information then available, demonstrated the following two major disadvantages,The use of hydrogen for shock cooling requires an enormous volume of gas - about 1,000 cubic feet for condensing each pound of metal as a pyrophoric dust which must be completely separated from this gas. Then if the gas is to be recycled for repeated use, the CO produced by the reduction reaction must be separated from the hydrogen. These separations are costly from the standpoint of equipment and operation. 11/The condensate is an impure, pyrophoric metal powder that must be purified and converted to coherent form. This is accomplished by distillation or sublimation of the metal. Distillation on a large scale involves difficulties inherent in the high boiling point (1,107° C.) and the chemical activity of the metal. To avoid these difficulties, the metal is sublimed at 600° C. and of very low pressure. This is quite easily carried out as a batch operation but is a costly procedure. A continuous sublimation process has not been accompli shed."

May 1, 1945

By Luis Briceño Arata

El presente texto señala las posibilidades de evolución cuantitativa de la producción minera del país hasta el año 2000. Para ello, se evaluaron los factores que influyen en la producción, la metolodología de proyección adoptada y así elaborar la producción de elementos estudiados.

Nov 1, 1974

By Rex T. Ellington

The fluidized bed is an effective method for investigating retorting phenomena and possibly a commercial means of retorting oil shale. Both were examined by Sinclair Oil Corp. (now part of Atlantic Richfield Co.) in the period 1.965 to 1968. The results of the work show that presence of an oxidizing environment during retorting results in loss of oil yield which indicates that vapor phase oil burns in preference to combustion of coke on spent shale. This has implications for several types of retorts. Correlation of the results of this work with that of other investigators shows that the partial pressure of retorting products in contact with oil shale during retorting has an effect on yield. Consideration of hardware indicates that there are several possibilities for commercial embodiment. As a companion to shaft-type retorts the fluidized bed could have good potential. Realistic assessment of costs suggests that further development may have to await commercialization of another process. The existence of a plant in which to test prototype size would markedly reduce such development costs. Results Preliminary development work with the apparatus was carried out using a fluidized bed of sand, as explained later, with the entire system brought up to temperature and flows stabilized. The shale was injected rapidly in a slug (batch) which had small mass compared to that of the high temperature system to make the reaction approach isothermality with reasonable approximation of instantaneous preheating. Typically, the temperature in the center of the bed dropped from 900°F to 600°F one minute after batch addition. It returned to 750' within three minutes and 900° within seven minutes. Obviously, the bed was quenched but it recovered rapidly. Average bed temperatures of 700' to 1020°F were examined to compare the effect of temperature with published results. Yields In the 700°F range were only 10 to 15%, of Fischer Assay (FA). Above about 950'F, oil yields decreased and gas yields increased. Nitrogen was used first as the fluidizing gas to provide a chemically inert medium. Incept for an insignificant dip at 895"F, Figure 1, oil yield was not affected by retorting temperature in the 800° to 900' range as long as residence time was adequate (16 minutes). At 925°F, the oil yield was some 103% FA. With further increase in temperature, the yield decreased to 86% FA at 1015°F. There is no increase in carbon on spent shale, the lost oil goes to Increased gas make.

Jan 1, 1972

By M. S. Janssen

The development of a design equation for, and the testing of, a constant- flow airlift pump IS described. The predictions of the new airlift model agree with the results of experiments carried out using riser diameters between 0.025 and 0.300 m, submergence depths between 5 and 10 m, suspension densities between 1000 and 1650 kg/m3, and a solids dg of 70 to 100µm. The predictions o the model also agree with data from the literature for submergence depths that reached 130 m. This airlift model was employed to simulate the pulp flow through a series of tanks, each of which was fitted with an airlift pump to transfer the suspension to the next tank. Particular attention was paid to the riser diameter, submergence of the airlift pump, and control of the air supply to the airlift pump during the simulated operation of a series of tanks. The results of the simulation highlight some design parameters that could affect the efficiency and operation of a plant that employs airlift pumps to transfer suspensions.

Jan 1, 1989

By César Macher

Dada la importancia económica y social que tiene la seguridad e higiene minera en el país, el objetivo del texto radica en crear las bases de un programa de higiene y seguridad que defina, evalúe, controle los riesgos industriales, como capacite a los estudiantes de ingenería de minas para mejorar los servicios que presta en la industria minera. El curso comprende cuatro capítulos y la distribución del tiempo de enseñanza en un periodo semestral. Entre los aspectos básicos del programa está la definición, significado económico y legislación sobre los riesgos ocupacionales; el conocimiento de los riesgos industriales referente a los agentes químicos, físicos, biológicos en los centros laborales; el muestreo y determinación de atmósferas polvorientas o control de riesgos, prevención de incendios y explosiones, normas de seguridad, y la forma de organización de seguridad e higiene minera. De otro lado, las presentaciones teóricas del curso se complementarán con problemas prácticos de la minería, material bibliográfico, y el desarrollo de prácticas con facilidades del Instituto de salud ocupacional, concluyendo con una serie de exámenes parciales teóricos-prácticos.

Jul 20, 1959

By Lynn L. Rethi

This U.S. Bureau of Mines report summarizes common obstacles found when attempting to implement health and safety strategies in small mines and small businesses in general industry. Recently, the U.S. Mine Safety and Health Administration focused much of its attention on addressing health and safety issues at small mines. Some of the more innovative interventions practiced by small businesses in general industry are discussed for consideration of their applicability to the mining industry. The most effective intervention strategy that was developed for small businesses is the Occupational Safety and Health Administration Consultative Program. The details of this program and other intervention strategies used by small mines and small businesses are presented.

Jan 1, 1995

By Ernest N. Wolff

You here are all familar with the myriad of new laws, some enacted and some pending, that affect the mining industry. These laws, for example those dealing with suspended matter, affect us in Alaska as they do you. Likewise, our friends in government, the Geological Survey and the Bureau of Mines, provide us with the same fine services that they do elsewhere. I am not going to speak today about these, but concentrate on one act of Washington, D.C. the impact of which is felt, for now at least, principally in Alaska. A little more than a year ago, I spoke in Spokane on the subject, "Governmental Challenge to Mineral Development in Alaska." I outlined some of the policies of Government which were operating to change the rules under which the industry operates and to alter the relation- ship between government, industry, and the individual. At that time the Native Claims Settlement Act had not been passed, but was on the verge of being so. In reading over what I said in Spokane, I note that I touched on many points where Government was actually challenging mineral development in Alaska. With the passage of the Alaska Native Claims Settlement Act, many of these actions were given a cloak of legality, and machinery was set up to concentrate the drive to tie up the public domain, machinery which will allow govern- mental control and interference with the actions of individuals on something like 90% of Alaska's land surface. This remarkable law is going to affect each and every one of you. Now, a year after its passage, we are only just beginning to see its lesson for the future. It was created by a coalition of powerful groups, who got other groups to support them by promising to deliver something they had no intention of delivering. Alaskan issues are again being used to get various groups not to oppose legislation which will severely harm them. It will help to understand the nature of this new drive if we understand the Native Claims Act and how it came into being.

Jan 1, 1973

By Robert E. Green, Robert A. Swanson

Ultrasonic attenuation and stress were measured simultaneously as a function of strain for aluminum single crystals tested in compression. The propagation mode and polarization of the ultrasonic waves were chosen with reference to the theoretical analysis presented in Part I. Good experimental agreement was found with this theory and with earlier experimental work in tensile tests. Support is given to the contention that ultrasonic -attenuation measurements are much more sensitive to the early stages of plastic deformation than are conventional stress -strain measurements. Dislocation meclzanisms are suggested which are compatible with both the present and the earlier experimental observations. A brief historical introduction of previous work concerned with the study of dislocation motion by ultrasonic-attenuation measurements has been given in Part I. The purpose of the present experimental investigation was to make use of the theoretical considerations from Part I in order to gain further knowledge concerning dislocation motions during plastic deformation. Emphasis was placed on the choice of propagation modes and polarization of the waves, such that interactions between these waves and dislocation movement on a specific slip system could be investigated. EXPERIMENTAL PROCEDURE Since the primary concern of this investigation was dislocation damping, other sources of damping were eliminated as much as possible. The test specimens were 0.5-in.-diam single crystals of 99.99+ pct pure aluminum grown from the melt by a modified Bridgman technique. Ultrasonic-attenuation measurements were made at a frequency of 10 megacycles per sec using a Style 56A001 Ultrasonic Attenuation Comparator manufactured by Sperry Products Inc. after a design by Chick, An- derson, and Truell.1 At this frequency the particle vibrations are essentially adiabatic and thermo-elastic damping should be absent. This frequency was selected since it was one of the frequencies used by Hikata et al.2 n conjunction with tensile tests on aluminum crystals, thus allowing direct comparison with this work. The use of quartz-crystal transducers insures that the amplitude of vibration is not sufficient to cause the break away of the dislocation loops from weak pinning points. The quartz-crystal transducers used all possessed a resonance frequency of 10 megacycles per sec and were thin circular discs 0.375 in. in diameter. X-cut crystals were used to generate the longitudinal waves and AC-cut crystals to generate the transverse waves. Aluminum was chosen as the basic material because it is a typical fcc metal whose deformation behavior is well-known and because the most recent work at the time the present research was initiated was that by Hikata et al. who used aluminum. The present tests were run in compression to see if such tests could be satisfactorily run in compression without being severely masked by grip effects.. A second reason was to compare the results in compression with those of the tension experiments of Hikata et at. Finally, shorter specimens could be run in compression with less over-all damping than in tension. All of the aluminum-crystal test specimens used were oriented for plastic deformation by single slip; i.e., they possessed the orientation having a maximum Schmid factor of 0.5. Because of the well-known time dependence 3 of plastic strain at constant stress, the test specimens were subjected to a quasi-static loading. Previous investigations4-' have indicated that attenuation after plastic deformation is also time-dependent, so any continuous loading of the specimen would show that changes in attenuation were also a function of strain rate. By loading the specimen to a given stress level and holding it constant until the recovery process was essentially complete, the time dependence was eliminated. The quartz transducer was permanently bonded to the aluminum crystal using Eastman 910 cement. Excess cement was removed from around the quartz with DMF (dimethyl formamide). Eastman 910 was found to be far superior for bonding, especially with regard to the shear-wave transducer, since it formed a solid bond which readily supports shear-wave propagation. The solid bond formed by the Eastman 910 cement also insured that the quartz

Jan 1, 1964

By D. A. Robbins

The application of remote sensing for environmental measurements is already being utilized. Aircraft mounted imaging spectroscopy has been utilized to evaluate areas of historical mining operations as well as active mine sites. To the extent that remote sensing can provide more sensitive, cost effective, and timely monitoring potential, the technology is of interest to the industry. Questions remain about the application and validation of the data and the availability of the technology in the private sector. This presentation will discuss some of the potential uses, benefits, and concerns related to remote sensing and efforts to monitor the technology's development.

Jan 1, 1999

By R Smart

This paper examines the longer-term predictive capacity of the GAMSPATH computer program (developed by the Alberta Research Council) for a waste rock (sample MS) obtained from the Kaltim Prima Coal (KPC) mine, Kalimantan that contained significant framboidal pyrite. The model was refined by comparison with the net acid generation (NAG) and column leach tests to provide a basis for calibration of the model for both short term and longer-term reaction trends. The oxidation of pyrite during the kinetic NAG test using H2O2 provides oxygen directly at the mineral surface, generating a measured oxidation rate for pyrite of 1.16 + 10-6 mol m-2 s-1, whereas the oxygen diffusion limited rate in the leach column air equilibrated reaction was of the order 10-8 mol m-2 s-1 as calculated from the GAMSPATH thermodynamic database. Results indicated that the oxygen derived from hydrogen peroxide had to be included as a reactant (eg a reacting mineral) in the simulation to account for the direct availability of oxygen at the sulfide mineral surfaces. Optical investigations identified the proportion, particle size, and surface area, of framboidal and euhedral pyrite in sample MS. The reactive surface areas of the two morphologies were very different (eg ratio: 5:1). To manage these two different pyrite morphologies the GAMSPATH thermodynamic database was updated to include framboidal pyrite, with similar thermodynamic properties and oxidation rate to euhedral pyrite but with a particle size based on the size of the individual internal framboid microcrysts. This modification, with framboidal pyrite reaction based on the size of its microcrysts produced results that correlated well with the kinetic NAG and column leach test results when the measured (kinetic NAG test rate) and calculated (column test rate) pyrite oxidation rates were employed. This provided some confidence that the model could be extrapolated to indicate longer-term geochemical reaction trends.

Jan 1, 2003

By George F. Kunz, Henry S. Washington

The recently discovered occurrence of diamonds near Mur-freesboro, Pike county, Ark., was brought to our attention by Mr. Samuel W. Reyburn (Trustee for Messrs. C. S. Stifft, A. D. Cohn, August Zinsser, Jr., and himself, owners of the property), through whose courtesy we investigated the locality of the deposit. Prospecting with the diamond-drill is now in active progress; but mining operations on a large scale have not yet been ordered. Geology.—The geology as well as the petrography of this interesting locality has been well described by Messrs. J. C. Branner and R. N. Brackett,' but they did not class it as dia-mondiferous, although Branner suggested that it might be. Briefly summarized, the igneous rock in which the diamonds are found is a vitreous peridotite, forming a stock or volcanic neck, which has broken up through the Carboniferous and Cretaceous quartzites and sandstones. After an extensive period of erosion, during which an unknown portion of the neck and pre-

Jan 1, 1909

By H. J. Rowley

THERE are many varieties of limestone, but for the general purposes of the pulp and paper industry, two classifications are sufficient: (1) High-calcium stone, which should be quite free from impurities and contain not less then 90 per cent calcium carbonate. (2) High-magnesium stone, containing not less than 25 per cent of magnesium carbonate. Before proceeding with detail on the use of limestone and lime in the industry, a few words regarding the pulp products made in Canada are desirable. By far the largest tonnage is made by grinding spruce and balsam logs on rotating sandstones or on artificial abrasive stones of the Norton or Carborundum types. This mechanical or groundwood pulp finds its largest use in the production of newsprint paper, of which it comprises about 80 per cent of the total fibrous substance employed-the remaining 20 per cent being unbleached sulphite pulp. No limestone or lime is directly employed in making groundwood pulp, as contrasted with the chemically prepared pulps, all of which require one or the other form of the base for their processing. Sulphite pulps comprise the next largest tonnage group. They are produced by boiling, under pressure and at elevated temperatures, spruce and balsam wood in chip form in solutions of bisulphites and sulphurous acid. The usual bisulphites employed are those of calcium and magnesium. Sodium, potassium, and ammonium bisulphites give progressively better pulps, but to date, in the absence of efficient recovery methods, cost has precluded their use.

Jan 1, 1939

By Verya Nasri, James Sullivan, Alex Varas

"INTRODUCTION Many major cities in the United States have a combined storm water and sanitary sewer network. Regular rainfall overwhelms the system capacity and results in millions of cubic meters of untreated sewage being dumped into local waterways. One legally mandated solution includes several kilometers of large diameter shallow or deep rock or soil tunnels, a pump station as well as associated collection sewers, diversion structures and drop shafts. In this paper, the basis for design of different system elements including the drop shafts and pump station is explained in detail. Common construction methods used for different type of shafts including tangential vortex and baffle plunge, and also pump station alternatives comprising cavern or various shaft configurations are discussed. DIFFERENT TYPES OF PUMP STATIONS The dewatering pump station serves as the heart of any deep CSO tunnel system and is critical to the goal of reducing CSOs by providing a controlled release of the stored tunnel volume to the wastewater treatment plant. As the major mechanical component of the project, the station will require the greatest attention by operations and maintenance staff. Designing a durable and easily operated pump station requires addressing some major challenges, including the following: • Longevity – equipment, materials of construction, and station environment • Controlling odors • Safety for operators and maintenance personnel • Easy access to equipment • Protection from hydraulic surges Location. Owners face a fundamental decision relative to the location of the pump station, which will affect how these challenges are addressed. The pump station can be built within the tunnel launch shaft or within its own dedicated shaft. This decision is driven by cost and schedule. Use of the tunnel launch shaft may provide owners cost saving opportunities by not having to construct a separate pump station shaft. However, this will likely extend the pump station construction as much as two years until the tunneling has been completed. Furthermore, delays to the tunneling operation would delay the pump station construction work, potentially leading to delay claims. For this reason, it has been more common to utilize a separate pump station shaft on recent CSO tunnel projects (Nasri et al. 2015)."

Jan 1, 2016

By I C. Carrasco, V G. Mirada, J F. D Domingo, F S. Leite

This paper investigates ore loss and dilution produced by rock movement in bench blasting. A total of four blasts, in which electronic detonators have been used, were monitored in Cobre Las Cruces Open Pit Mine (FQM Ltd) in Gerena (Sevilla, Spain). Rock motion has been obtained in 137 points of the free face and 6 points inside the block. Multiple liner regression has been applied to predict rock motion and estimate ore dilution as a function of hole coordinates, rock contacts, powder factor/hole, amount of explosive per blasthole, burden, spacing, hole length, stemming length, explosive energy, hole row, subdrilling, blast sequence, stiffness ratio, blasthole distance to free face, rock density and Young’s modulus. The model is statistically significant with a determination coefficient over 0.8. Rock motion measurements in 31 more points have been used to validate the model and to show a reduction in ore dilution.CITATION:Domingo, J F D, Leite, F S, Mirada, V G and Carrasco, I C, 2015. Dilution, ore grade and blast movement calculation model, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 71–78 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Michael L. Sorokin

The behaviour of cobalt during processing of nickel raw material is analysed within the Ni-Co-Fe-S-O-SiO2 system using the computer model. For this purpose the thermodynamic parameters for "three-suffix" Margules's equations in Co-Fe-S and Co-Fe¬Ni-O-S1O2 systems were computed! Phase and iso-activity diagrams for Co-Fe-S system, and phase diagrams for the systems Co-O, Co-Fe-O, Co-Ni-O, C-oO=SiO2 and Co-Fe-O¬SiO2 are calculated using the developed computer programs and identified parameters. The diagrams are used to analyze cobalt behaviour at smelting and converting.

Jan 1, 1995