Search Documents

By W. E. Newton

THE following notes are offered primarily to show that industrial minerals or their products have a much more important place in the metallurgical industry than is perhaps generally realized, and with the hope also that some statement by the metallurgical consumer of the relative merits of various materials for particular requirements or services will l;>e of value to the industrial mineral producer. These notes are not in any way presented as complete. Also, some of the statements made may be debatable. The grouping adopted is as follows: (1) Refractories; (2) Fluxes; (3) Construction materials; and ( 4) Miscellaneous applications. Fuels are not dealt with in the present paper. REFRACTORIES GENERAL: Refractories are materials which will withstand high temperatures with-out melting or becoming markedly soft or pasty. While their primary function is to withstand heat, they are usually called upon to resist one or more of the following destructive influences: abrasion, pressure, corrosion by slags or fluxes, and rapid changes in temperature. Refractory materials may be conveniently divided into three classes: (1) Acid refractories-consisting of silica, or containing silica as their chief constituent. They combine more or less readily with metallic oxides, forming silicates, and are hence termed 'acid'. The most important of these are quartz, quartzite, siliceous sand, tripoli, Dinas rock, and ganister. Most fire-clays, although generally considered neutral sub-stances, contain relatively small amounts of free silica and are, to that extent, acid. (2) Neutral refractories-the term is merely relative in most cases, since, at high temperature, many of the refractories that are classed as neutral will react chemically with a strong base, functioning as a weak acid; or, conversely, with a strong acid, functioning as a weak base. Chrome and graphite are the most nearly neutral of all the commonly used refractory materials.

Jan 1, 1936

By E. S. Peters, M. J. van Rensburg, M. Le Roux, Q. P. Campbell

"The demand for energy has continued to rise worldwide in line with population growth. The majority of South Africa’s electricity is supplied by coal-fired power stations. The amount of fine coal (-2 mm) generated at coal processing plants has increased, due mainly to mechanized mining methods. Fine coal retains more water, which lowers its heating value.Drying the coal is costly and it is difficult to achieve the required moisture content. Consequently, coal fines are often discarded. An estimated 8% of the total energy value of mined coal is lost1.Fluidized bed technology is often used to dry coal thermally, but this method is expensive and has an adverse environmental impact. The objective of this study was to investigate the removal of moisture from fine coal (<2 mm) in a fluidized bed operated with dry fluidizing air at moderate temperatures as the drying agent. The effects of different air temperatures and relative humidity levels were investigated in a controlled environment. The study further investigated the influence of coal particle size on moisture removal.The drying rate was found to increase with increasing temperature. The relative humidity of the drying air had a more pronounced effect on the drying rate, even at temperatures as low as 25°C.. It became more challenging to remove moisture as the particle size decreased. The gain in calorific value was greater than the energy required to dry the coal samples, showing that a fluidized bed using moderately warm dry air is an energy-efficient drying technology. The energy efficiency of the fluidized bed compared favourably with other thermal drying methods.Paper written on project work carried out in partial fulfilment of Degree in Chemical Engineering(NWU) - Pursuing Masters in Coal Beneficiation"

Jan 1, 2015

Over the last 20 years the mining industry has played a key role in the further development of many Central Queensland and New South Wales communities. The number of people who are employed by the coal mining industry, the number of transient residents, shift work and the town facilities have all contributed to how the community views the coal mining industry. As the coal mining boom continues and the mining communities continue to grow more emphasis is needed to address the community concerns, specifically the socio-economic and environmental impacts that the coal mining companies may have on these communities. Central Queensland coal mining operations are situated in the Bowen Basin. Many of the towns in the region have been developed specifically for the coal mining industry with 13 - 50 per cent (Australian Bureau of Statistics, 2006) of people living in the communities being directly employed by the mines. The introduction of shift work, differing rosters and the mining boom have resulted in considerable changes to these communities with more transient contractors and permanent employees taking up residence outside of these communities. This change, however, has not been as noticeable in the Hunter Valley region. The Hunter Valley, situated in the Sydney Basin has two main mining towns, Singleton and Muswellbrook. Of the 37 173 (Australian Bureau of Statistics, 2006) people that reside in the communities 13.8 to 16.5 per cent (Australian Bureau of Statistics, 2006) are employed directly by the mines. The Hunter Valley is a large tourist destination due to its many vineyards; this results in a diverse community where mining is not the sole means of employment. Similar to Central Queensland the mining boom has brought more people to the Hunter Valley region, although greater percentages have taken up residence in the communities. The views vary between the two regions on the coal mining industry, specifically on the socio-economic and environmental impacts that the industry may have on the surrounding communities.

Jan 1, 2008

By Robert W. Lawson

INTRODUCTION The two basic types of mine-air compressors are the positive-displacement compressors and the dynamic compressors. Positive-displacement compressors con¬fine successive volumes of air within a closed space and increase the pressure by reducing the volume of that space. Reciprocating and rotary compressors operate on this principle. Dynamic compressors utilize an impeller to acceler¬ate the air, with the increased air velocity converted to pressure through a stationary diffuser. Centrifugal compressors and turbocompressors operate on this principle. Reciprocating Compressors Reciprocating compressors include both single-stage and multistage units. For mine service the most com¬mon is the two-stage intercooled compressor having an atmospheric pressure intake and a discharge pressure of 689 to 861 kPa (100 to 125 psi). The cylinders of a reciprocating compressor may be either single acting or double acting. In the single-acting cylinder, compression occurs on only one side of the piston, while, in double¬acting cylinders, compression occurs on both sides of the piston. Fig. 1 shows a cross-sectional view of a typical two-stage double-acting water-cooled reciprocat¬ing compressor. Fig. 2 illustrates the sequence of opera¬tions occurring in the cylinder of a reciprocating com¬pressor. Most modern mine compressors are double acting and are driven by electric motors. Induction motors are used on low-powered compressors, and synchronous motors are used on larger compressors. Steam-driven compressors once were common and still are applied where a reliable source of low-cost steam is available. For this type of compressor, steam is a desirable power source since a governor that senses the discharge pres¬sure can be used to control the steam inlet. This can be used to regulate the compressor speed to compress only air sufficient to meet the mine&apos;s requirements (up to the capacity of the unit). Unlike a constant-speed electric¬driven compressor, no other regulation is required for the cylinders of a steam-driven unit. Rotary Compressors Rotary compressors include sliding-vane, liquid¬piston, two-impeller straight-lobe or cycloidal, and helical-lobe units. Each of these has specific advantages and applications. Of these, the helical-lobe or "screw" compressor has the greatest application for supplying "100-lb air" [689 kPa (100 psi) ] to small- and medium¬size underground mines. Fig. 3 illustrates the operation of a sliding-vane compressor. Fig. 4 illustrates the operation of a helical lobe or screw compressor. Fig. 5 illustrates the operation of a two-impeller straight-lobe compressor. Fig. 6 illustrates the operation of a liquid¬piston compressor. Centrifugal Compressors Centrifugal compressors deliver 0.94 m3/s (2000 cfm) or more of air, and they are best suited to supply¬ing large volumes of compressed air for base loads. The efficiency of a centrifugal compressor declines rapidly when its operation deviates from its design point. If the power cost is not a critical consideration, a centrif¬ugal compressor is attractive as a result of the low initial and installation costs and the high degree of reliability. Fig. 7 illustrates a typical four-stage centrif¬ugal compressor, and Fig. 8 is a cross section of this type of unit. COMPRESSOR SELECTION The process of selecting a compressor requires sev¬eral considerations, including the capacity, the control system, the location, the power supply, and the cooling provisions. Compressor Capacity To determine the required capacity, the total air quantity and pressure requirements must be calculated. The air consumption of various tools, as listed in Table 1, must be included in this calculation. Some of the other considerations include: 1) The correction factor for altitude, as listed in Table 2, must be included in the calculation. While pneumatic tools require additional compressed air as the altitude increases, the compressor produces less. 2) A correction factor must be incorporated for the use of multiple tools. Table 3 lists appropriate correc¬tion factors for rock drills.

Jan 1, 1982

By A. M. King, J. M. Neilsen

"Roughness at varying scales is an important component of the shear strength of discontinuities. Small scale roughness can be assessed in drillcore and through laboratory testing of drillcore derived samples. Large scale roughness, or waviness, also plays an important part in peak shear strength and a number of methods for its incorporation into defect plane strength models are presented.A number of methods for capturing waviness data from exposed faces are reviewed. A method is presented for deriving waviness from downhole televiewer data, which is shown to be significantly more accurate than structural data derived from core logging. The method is based on work undertaken in the highly anisotropic bedded units of the Hamersley Province, Western Australia where televiewer surveys are routinely undertaken. Values of waviness are derived through a review of variation in dip resolved in the direction of the slope face. This method allows design engineers to incorporate large scale roughness in defect plane shear strengths at the design stage.INTRODUCTIONThere are a number of constitutive models currently being applied by rock mechanics practitioners in calculating defect plane shear strength parameters, such as Patton, Barton – Bandis and Hencher [1, 2, 3]. Most of these shear strength determinations are typically undertaken by determining the base or residual friction angle, and applying corrections for small and large scale surface roughness."

Jan 1, 2015

By Edward Gridley

At the meeting of the Institute, held at Roanoke, Va., in June, 1883, I gave some facts in relation to charcoal pig iron of unusual strength, made from our carbonate ore taken from the mine at Amenia, N. Y. My object in again bringing the subject to the attention of the Institute, is to obtain, if possible, the solution of a prohlem in connection therewith. Our furnace is of the old type, stone stack 32 feet high by 9 feet 2 inches at top of bosh; bosh about 67O pitch; stone hearth; three tuyeres of 31/4-inch opening; fuel, a mixture of hard and soft coal; blast about & to # pound pressure, and heated to 400&apos; to 600° Fahr. by iron pipe oven on top of stack. The analysis of the roasted carbonate ore, as before given to the Institute, is as follows:

Jan 1, 1884

By Zhihe Dou

SHS reaction system has advantages of heat flux density, energy concentration and reaction speed, with sufficient conditions in thermodynamic and kinetic reaction. This paper invented a new technology of SHS metallurgy of preparing melting point alloys and refractory compounds using its own chemical energy. SHS-leaching process for preparing nano boron powder or ultrafine boride powder and SHS-casting process for preparing titanium-based alloy and immiscible alloy were studied. The results indicate that highly active boron powder of greater than purity of 93%, particle size less than 100nm and purity greater than 98.5%, particle size less than 400nm REB6 can be prepared. With SHS-Casting process, the oxygen content of less than 0.59% ferrotitanium, oxygen content of less than 0.5% titanium alloy and ?40-80*100mm large size of CuCr, Cu-Fe alloy ingots were prepared. This technology has greatly enhanced the thermal reduction method added values of preparing metallurgical products and its competitiveness.

Jan 1, 2014

By Vítor Covre Evangelista da Silva

Esta proposta objetivou desenvolver uma análise teórico/experimental da influência de 2% Ag (em peso) em uma liga de solda Sn-40%Bi solidificada unidirecionalmente em regime transitório de fluxo de calor. Correlações experimentais entre os parâmetros térmicos de solidificação como velocidade de deslocamento da isoterma liquidus - VL, taxa de resfriamento - ?L e parâmetros microestruturais como espaçamentos dendríticos secundários – l2 foram determinados. A caracterização microestrutural foi realizada por meio de microscopia ótica e eletrônica, difração de raios-x, além de fluorescência de raios-x para obtenção dos perfis de macrossegregação dos solutos (Bi, Ag). Para determinação do perfil de dureza foram realizados ensaios de dureza Vickers. As microestruturas brutas de fusão da liga Sn-40%Bi-2%Ag são compostas de dendritas ricas em Sn decoradas com partículas de Bi circundadas por uma mistura eutética (Sn+Bi) e partículas primárias de Ag3Sn. Os parâmetros térmicos decresceram com aumento da camada solidificada, permitindo uma ampla variação: ?L ? 0,1 a 10,0°C/s, VL ? 0,2 a 0,9mm/s e GL ? 0,4 a 11,0°C/mm. O teor de bismuto não variou significativamente, ao passo que a prata variou de forma efetiva, concentrando-se no início do lingote (até próximo de 35mm). O surgimento de braços dendríticos terciários em 15mm conteve a diminuição da microdureza Vickers, esperada para as posições mais afastadas da interface metal/molde.

Aug 16, 2017

By G. S. S. Raman, M. S. Klima

Coal refuse slurries stored in tailings impoundments can potentially lead to environmental concerns such as effluent seepage, property devaluation, and in extreme cases, dam failures. Pressure filtration offers an opportunity to reduce the impoundment requirements by providing significantly drier solids. A full-factorial design was used to study the effects of temperature and pH on dewatering a refuse slurry obtained from a coal preparation facility in Pennsylvania, USA. The experimental results indicated a strong effect of temperature on cake moisture as the cake moisture after about 2800 s was 22% at 43 °C and only 36% at 10 °C for tests conducted at pH 3. ANOVA results confirmed the statistical significance of pH, temperature, and their interaction effect. Also, the results showed no significant differences between the tests conducted near neutral and alkaline pH values at low and ambient temperatures. On the other hand, Tukey's test indicated higher reductions in cake moisture at higher temperatures for lower pH values. This study affirms the need to monitor and control the pressure filtration process as throughput could significantly vary with changes in temperature and slurry conditions.

Jun 17, 2019

By Benoit Bissonnette, David Gelderland

"The Campbell Mine Constructed Wetlands has been in full operation, processing effluent from the water treatment plant of the mill circuit for the last two years.The overall results are extremely positive with dramatic improvements for the originally targeted parameters – Ammonia, Copper and toxicity.• Ammonia concentrations were reduced from an average of 5 mg/L to an average of 0.43 mg/L which translates to an average reduction of 91%.• Copper concentrations were reduced from an average concentration of 0.054 mg/L to an average of 0.019 mg/L, which translates to an average reduction of 65%.• LC50 Acute toxicity testing revealed no impact.• IC25 Chronic toxicity tests revealed no impairment to growth or reproduction.As a result of the improvements in discharge water quality from the wetland, 100 percent compliance with respect to all Certificate of Approval, MISA and MMER regulations for effluent will be consistently achieved.The system has proven to be very easy to operate and maintain, with a minimum of care. Given some basic rules are followed, the construction of the wetlands was straightforward and relatively inexpensive compared to other treatment methods.The ecological benefits of the operation of the wetland are also quite substantial, as is the positive image of the corporation in environmental stewardship.INTRODUCTIONOver the last four years, Campbell Mine has adopted an aggressive schedule for the development of wetlands for use as the final stage of effluent treatment within the tailings management facility. The focus of this work has been to utilize natural biological systems to provide Campbell Mine with a 100 percent compliant water quality with respect to all MISA, MMER and COA discharge criteria at all times throughout the effluent discharge period."

Jan 1, 2003

By M. Moseki

Paper written on project work carried out in partial fulfilment of B.Sc. (Eng.) (Metallurgy of Materials) degree This paper presents the research into melting of scrap for job creation purposes in rural areas. The research was done on behalf of Mine Recycling Services (MRS), the company that will implement the project. The project involves the research into available cost effective and easy to operate technology. The paper covers the experimental and theoretical work that was conducted. The results were used to determine the best equipment and method for melting and casting brass scrap.

Jan 1, 2002

By M. Hancer

The sign of the surface charge of selected potassium soluble salt minerals namely KClO4 , K2SO4 , KNO3, and KCl was determined from nonequilibrium electrophoresis measurements and found to be negative for each of the salt. Dodecylamine flotation of these salts revealed that the concentration of amine required for flotation increases in the order KClO4< K2SO4< KNO3<KCI. Precipitation of the amine collector colloid was not required for flotation of the oxyanion salts and in this case it appears that adsorption of the dodecylamine cation is sufficient to create the hydrophobic surface state. The order for flotation is explained in terms of surface hydration of these respective potassium salts based on contact angle measurements and FT Raman spectroscopic characterization of water structure.

Jan 1, 1999

In order that the processes seen may be followed in their proper &apos;order, the subject will be dealt with as follows, (1) Wallaroo and Moonta Mines; (2) Wallaroo and Moonta Mines Smelting Works; (3) Broken Hill Mines; (4) Concentration at Broken Hill; (5) Smelting and refining of Lead, Silver, and Gold at Port Pirie. The first acquaintance with the copper region was made at the Yelta shaft and dressing mill of the Parramatta Copper Mines Co. at Moonta. The country rock at Moonta is a hard, tough, felsitic porphyry, the copper lodes having a general strike of N. 30&#176; Kilipping from 500 to 70&#176;. This necessitates shaft-sinking on the lode, and underlay shafts are the rule on the field. The ore is raised in the Yelta shaft in wheeled skips, and consists of &#183;chalcopyrite, bornite, pseudomorphic hematite, containing, in addition, molybdenite and tourmaline. The ore from the bins at the brace is passed over a grizzly; the over-size is hand-picked into smelting ore, concentrating ore, and waste rock (00 attle ), which is sent below for filling. The under-size is elevated to a trommel having in. holes. The over-size falls on to a picking belt made up of lengths of rope strapped with iron, working over wooden pulleys.

Jan 1, 1907

By J. L. Eakin

Systematic flooding was introduced into Nowata County, Okla., in May 1931. The results of this means of stimulating the nearly depleted Bartlesville reservoir in the county has been the subject of four Bureau of Mines Reports of Investigations.2-5/ This report presents a discussion of four full-scale water-flooding projects in the Delaware-Childers field and 1 pilot project in the Curl Creek field (fig. 1). All five plants have been in operation for only a few months. Although substantial increases in the rates of oil production have been obtained 1 by the injection of water, the projects are of particular interest at this time because of the novel methods of operation and new equipment that are being employed. One project utilizes a portable "package" plant designed for a pilot operation. All of the controls for this project are centrally located. The design makes it possible to remove the test plant to another location if the project is unsuccessful or if the unit is to be replaced by a larger plant. This project also utilizes diatomaceous-earth filters successfully for the first time and makes use of plastic pipe. Another novel feature of the operation is the aeration of Arbuckle limestone water through an airlift in the supply well.

Jan 1, 1955

By Jon Errey, Aleksandar Petrovic, Karl Haase

"Developing a gold deposit of this magnitude in the Amazonian jungle of Guyana posed many challenges. This paper describes not only the process & logistical challenges arising from the remote mine site location in a tropical environment with a local industry unaccustomed to recent large scale gold mining operations, but also the innovative technical solutions employed to address the unique ore body characteristics. The best examples of this approach were dealing with the initial high clay content saprolite ore from the development phase and primary mining pits whilst ensuring that the design also implemented the right method to deal with the future fresh rock in an environmentally sensitive habitat. In order to do this separate individual crushing flowsheets were generated, focusing on the specific material handling equipment that would be suitable to handle these various types of material and ensure high recoveries were maintained.INTRODUCTIONAurora gold mine is located in forested region of Guyana, 170 km west of capital Georgetown, and 130 km West North-West of Bartica, a settlement at the junction of the Essequibo and Cuyuni Rivers.The Aurora gold project (Aurora) is a 5,000 tonne per day open-pit/underground operation, which will produce a total of 3.29 million oz. gold – averaging 194,000 oz. per year – over an initial 17 year mine life. At the final investment decision in 2014 Aurora had a total resource of 6.54 million ounces in the measured and indicated categories (62.83 million tonnes at 3.24 g/t Au) as well as additional 1.82 million ounces in the inferred category (16.93 million tonnes at 3.34 g/t Au)."

Jan 1, 2016

By André Vervoort

To learn more about the fundamental roof behaviour in South African coal mines, accurate underground measurements of roof deflection were conducted in bord and pillar panels during development and pillar extraction. To conduct these measurements a survey levelling technique was adapted. The overall system reading accuracy was established as being within 0,4 mm on a 15 m sighting distance. The underground sites were modelled and, for a roadway development, similar symmetrical curvatures were calculated by a linear elastic model, as were measured underground. In a pillar extraction panel, a significant amount of bed separation was measured and the roof underwent an a-symmetric movement due to the close presence of the mined out area at one side of the roadway.

Jan 1, 1992

By M. Soya, M. Imazu, Ö. Aydan

"SUMMARY Taru-Toge tunnel is being constructed using drilling-blasting technique as a part of expressway project connecting Shin-Tomei Expressway and Chuo Expressway at the boundary of Shizuoka and Yamanashi Prefectures in the Central Japan. The maximum overburden is about 400 m. The authors have been carrying out a monitoring program to measure dynamic and multi-parameter responses of tunnel during and soon after the blasting operations using a multi-parameter monitoring system (Acoustic Emissions (AE), Electric Potential (EP), Temperature (T), Humidity (H) and Air Pressure (P)) and stand-alone type compact accelerometers developed by the first author. The measured response involves dynamic vibrations and other measurable parameters caused by blasting as well as by stress-redistribution around the tunnel face. This is one of the first attempts in the world to measure the response of rock mass caused by blasting at a very close vicinity of the tunnel face. In this paper, the authors present the outcomes of this unique monitoring study on the dynamic responses of the Taru-Toge tunnel during excavation and discuss their implications in actual applications. INTRODUCTION The real time monitoring of the stability of tunnels are of great importance when tunnels are prone to failure during excavation such as rockbursting or squeezing (i.e. Aydan et al. 1993, 2001). Experimental studies by the authors showed that rock indicates distinct variations of multi-parameters during deformation and fracturing processes (i.e. Mizutani et al. 1976; Aydan and Daido 2002; Aydan et al. 2003, 2011). These may be used for the real-time assessment of the stability of rock structures. An application of this approach was done to the Taru-toge tunnel a part of expressway project connecting Shin-Tomei Expressway and Chuo Expressway at the boundary of Shizuoka and Yamanashi Prefectures in the Central Japan (Imazu et al. 2015). The parameters measured involve electric potential variations, acoustic emissions, rock temperature, temperature and humidity of the tunnel in addition to the measurements of convergence and loads on support members during the face advance."

Jan 1, 2016

By D. Kump

Barrick closed the Bullfrog Operation in November 1999.During its life, the Bullfrog produced ore from three open pit mines and an underground mine; 32,000,000 tons of ore were processed at the 9,000-ton per day oxide mill. The mill tailings were deposited in a 320-acre tailings impoundment. When operations ceased, an estimated 750,000,000 gallons of water remained to be removed from the tailings impoundment. During operation, the drain down water from the tailings impoundment was pumped back to the mill for reuse; since closure of the mill, the drain down water has been managed by a combination of passive and forced evaporation.

Jan 1, 2004

By Majorkiewicz A

Engineering of gold treatment facilities complete with infrastruc- ture in a remote location such as Papua NewòGuinea present unique problems to the design team. Site location, topography, ground conditions and infrastructure are some of the major hurdles to overcome when setting out on the design of such plants. This paper discusses two such plants, located in two distinctly different areas of Papua New Guinea and the solutions evolved in order to design successful operating facilities.

Jan 1, 1991

By Nedam Abed

A fundamental study of the sonochemical leaching of chalcopyrite in ferric ion media has been performed to understand and quantify the effects of sonication and other parameters on leaching reactions. The study covers sulfate and chloride media. The main leaching reaction: CuFeS2(s) + 4Fe3+(aq) Cu2+(aq) + 5Fe2+(aq) + 2S(s) (1) was found to be dependent on temperature and initial particle size, but less dependent on ferric ion concentration. Leaching kinetics were not affected by ferrous ion concentration or the amount of chalcopyrite added. Leaching was performed under a variety of sonication and leaching conditions. Reaction stoichiometry was confirmed through detailed wet chemistry analysis and mass balance calculations. The use of ultrasound activation showed a clear improvement in leaching kinetics and amount of copper extracted, sonication having a catalytic-like effect on the leaching reaction. Compared to experiments without sonication, reaction rates were 2-3 times faster at the same temperature, and could be faster by a factor of 20 for the same initial particle size. Regardless of initial particle size, the amount of copper extracted was comparable under sonication, and could be twice that under chemical leaching, implying the avoidance of fine particle grinding. Sonochemical leaching was found to be only temperature dependent, where the best copper extraction was at 75C. Leaching was further enhanced by the use of a grinding aid. The leaching behavior of chalcopyrite particles remained similar with and without ultrasound activation, implying that the known passivation mechanism in the oxidative leaching was not eradicated. Sonication resulted in coarse particle breakage (ultrasonic milling). Sonication did not contribute to particle passivation, as affirmed from different leaching procedures and sonication in aqueous and organic media. Parabolic leaching kinetics were confirmed for leaching experiments.

Jan 1, 2003