Search Documents

By M. P. Brameld, G. Archambault, R. H. McCorkell

"The rates. J. at which materials emit radon are of interest in studies of the sources of radon in mines. buildings. soils overburden and other places where it may indicate the location of ore or be a health hazard. Here J values were determined by measuring the radon concentrations by means of scintillation counters or alpha-particle track detectors in chambers in which specimens were sealed. Errors in the measurements due to leakage from the chambers. lack of secular equilibrium in the decay series of the radon measured, or the limited rate of diffusion of radon from powders or within the chambers were shown to be insignificant or could be corrected. Scintillation counter measurements are highly reproducible; track detector measurements also appear useable and may be made on many small samples using small, simple chambers. J measurements were made for uranium ores, drill cores, standard CANMET pulps. concrete and gypsum board. Powdering of ores had little effect on their J values.IntroductionIn the mining and mineral sciences, radon (222Rn) is of interest chiefly for two reasons: in geochemical exploration for mineral deposits its presence in soil. overburden and water in more than background concentrations may indicate the existence and locations of uranium deposits and, if present in sufficient concentrations, it is a possible health hazard in mines, mills and other places where people live and work. The latter aspect of radon's role has received considerable attention recently(1,2,3,4,5), and surveys of soil-gas radon concentrations have been used for some time in searches for uranium deposits(6,7,8,9,)."

Jan 1, 1981

By Roger W. Swindle

INTRODUCTION The Uravan Mineral Belt in southwestern Colorado and southeastern Utah is a uranium-vanadium mining district with a unique set of radon daughter control problems. This paper describes these problems and the methods that have been developed to deal with them. The greatest emphasis is placed on the problems caused by air stagnation because these are the most frequently encountered ventilation problems, and this is an aspect of uranium mine ventilation that is often misunderstood. VENTILATION PROBLEMS Most of the mine ventilation problems in the Uravan Mineral Belt are caused by one or more of the following conditions: (1) the highly irregular ore deposits are difficult to locate and delineate, (2) air stagnation occurs in many areas of the extremely irregular mine workings, and (3) it is often necessary to reactivate old workings with small airways that are often caved. Planning Problems Orebodies in the Uravan Mineral Belt are so discontinuous and unpredictable that they are difficult to locate and delineate. Data supplied by surface drilling and underground test holing are often misleading; very little ore may be found in the vicinity of an ore hole, and, conversely, an unmineralized hole may be adjacent to a high-grade ore deposit. Also, ore guides are often ambiguous, and their interpretation is usually a matter of opinion.

Jan 1, 1983

By G. Belzil, F. Robichaud, M. Fullam

ABSTRACT The Goldex mining and milling complex is operated by Agnico-Eagle and is located in the Abitibi greenstone region of northwestern Quebec, Canada. Commercial production started in 2008. Average gold recovery is 93.5% with approximately 68% of gold recovery coming from the gravity circuit. During the first three years of production, three gravity audits were carried out to optimize performance of the gravity circuit. This paper presents results of the audits and the development of a model linking gravity and overall gold recovery, and outlines improvements made to increase gravity performance and reduce operating costs.

Jan 1, 2013

By S. J. Prison, C. R. Smith

The effect of fluid injection to control water coning in oil and gas wells was investigated. Analytical and model techniques were employed. The factors investigated were the position and length of the completion interval, the point of fluid injection, the viscosity of the injected fluid and the relative thickness of the oil and water sections. The resulting influence of these factors on the net producing water-oil ratio was determined. Several important conclusions can be drawn from the study. In general, it was found that the net producing water-oil ratio can be reduced by fluid injection. The magnitude of this reduction depended on the factors listed above. An important practical consideration is that the injection fluid may be either oil or water. If the injected fluid is less dense than the connate water of the reservoir, the fluid will not be lost. This fact is reassuring when valuable oil is being injected. Efforts to suppress water production were more successful when the injection fluid was more viscous than the reservoir oil, or when a zone of reduced permeability existed in the vicinity of the point of fluid injection. Under test conditions, little benefit was derived through the use of impermeable barriers or cement "pancakes". INTRODUCTION The occurrence of water coning has been known for at least 60 years. In thin oil or gas pay sections, the presence of an oil-water or gas-water contact hinders production and often causes early abandonment of the afflicted well if a completion is even attempted. Even when relatively thick pay sections are found, the encroachment of water when a water drive is present will eventually pose serious water coning problems. This water is often corrosive, expensive to separate from the oil or gas and is costly to dispose of. The theory of water coning has been discussed by a number of authors. 1,2,3,4 Briefly, water coning to the producing interval in a well is due to pressure gradients resulting from the production of fluid from the reservoir. These pressure gradients will cause a water cone to rise toward the bottom of the producing interval if a water-oil or water-gas contact exists. The tendency of the water to cone is offset or partially offset by gravity forces since the water has a higher specific gravity than the oil. A balance then exists between two forces, gravitational forces arising from the difference in specific gravities of the oil and water, and the pressure gradients causing the flow of fluids to the wellbore. If the pressure gradient exceeds the gravitational force, water coning to the wellbore occurs and water production results. Through the years considerable thought has been given to the water coning problem. More than 50 U. S. Patents have been granted to inventors on the subject. A relatively complete literature review of the water coning problem has been made. 5 A number of these patents hold considerable promise for the solution or the partial solution of the water and/or the coning problem. Very little has been written describing field tests of techniques for the suppression of water coning. A notable exception is the paperby West. 6 He reports success in reducing gas coning by a combination of gravel packing and oil injection above the oil-producing interval. He also describes a comparable method to prevent water coning, but provides no field examples. This study experimentally and analytically verifies the benefits of oil injection as a means of partially or completely suppressing the water cone. While the gas coning problem was not treated, it is anticipated that results comparable to those obtained in water suppression could be obtained with reduced oil injection since the viscosity contrast between oil and gas exceeds that between oil and water. For the purpose of this study, the conventional potential flow theory was applied to the water-coning problem. The experimental verification centered on both a radial and a linear model. The model study permitted the investigation of complex flow configurations and the use of fluids of differing densities and viscosities. No analytic expressions are available to permit a solution of the problem as stated (see Fig. 1).

The income of the Institute is derived from dues, subscriptions to MINING AND METALLURGY sale of publications. These sources are fortunately supplemented by the interest from invested funds now amounting to over $500,000, a considerable portion constituting endowments for especial purposes. Aside from the medal funds the principal endowments are the James Douglas Fund for support of the Library, the Rocky Mountain Fund and the Seeley W. Mudd Memorial Fund. The income from the two last named is available for the support of research and a variety of other purposes. It is allocated by the Board of Directors upon recommendation of standing. committees in each case. An active effort is being made to increase the endowments of the Institute, it being felt that unusual opportunities exist for research and public and professional service through the organization and at a minimum of expense. J. V. W. Reynders is chairman of the Endowment Committee.

Jan 1, 1929

By Michael L. Nave

Mining belt conveyor elements are becoming larger and more expensive. Conveyor reliability requirements are rising. Conveyor condition monitoring can aid maintenance, reliability, and risk management in conveyor system operation. This paper examines the application of condition monitoring in coal mining belt conveyor systems. Types and form factors of condition sensors are described. Example costs are included. Suggestions for OEM developments are examined. Application problems are discussed. Two simple cost case studies are presented.

Jan 1, 2000

By Aarne Kopanen

In recent years, various renovations have been carried out in the production chain of the Outokumpu copper refinirg process. The anode casting shop, which is the final integral production section at the Harjavalta copper smelter built in its original form in 1945, was fourxl unsuitable for technical and capacity demads during longer periods of operation, and a new casting shop was built in 1974. The electrolytic copper refinery of Outokumpu Oy at Pori was built in 1941, and subsequently expanded in two stages. Even with its present limited scale of production it has been fom important to mechanize the main operations. This work was started in 1967 with the design and construction of the starting sheet machine connected with the cathode washing and unloading machine as a combined unit. Mechanized treatment of anodes has gained advantage particularly from the new design of a highly automated anode casting shop. In the further development of the mechanization a stripping machine for, starting sheets was designed and installed, starting operation in 1974.

Jan 1, 1976

By J. A. Bownocker

The existence of petroleum in the rocks of Ohio and Indiana seems to have been first shown by wells dug for salt. The fuel, however, was objectionable owing to its odor and inflammability. Not until the Drake well was drilled in 1859 did the people appreciate the value of rock oil, and then they at once began plans to secure the coveted fuel. The first successful well in these two states was near Macksburg, in southeast Ohio, where at a depth of 59 ft. (17 m.) oil was found in commercial quantity (1860). A year later this fuel was secured on Cow Run, in the same county, and at about the same time in Noble, Morgan and perhaps other counties in that part of Ohio. The second great step in the production of oil in Ohio and Indiana was taken in 1884 when the reservoir of natural gas in the Trenton limestone of northwest Ohio was tapped, and where a year later oil was secured in the same formation. Petroleum in this limestone was obtained in Indiana in 1889.' The third step in the production of oil in Ohio and Indiana is associated with the Clinton sand of Ohio. Natural gas in large volume was discovered in that rock at Lancaster, in 1887, and the area has been extended until it has become the largest individual producer in the world. The presence of natural gas in such great volume all but demonstrated to the driller that oil lay hidden near by. Soon the search for it was started but not until 1899 was petroleum in commercial quantity found in the Clinton sand, and a large pool was not located in it until 1907. The fourth step in the developrllrnt of the industry was taken in 1913, when the pool in Sullivan County, in western Indiana, was opened. The producing rock is the Huron sandstone, which is the topmost member of the Mississippian system.²

Jan 1, 1921

By Joshua Hescock, Zach Agioutantis

"The Surface Deformation Prediction System (SDPS) has been developed as an engineering tool for the prediction of subsidence deformation indices through the implementation of an influence function. SDPS provides a reliable and fast method for the prediction of mining-induced displacements, strains, tilt, and so forth at any elevation between the seam and the horizontal or varying surface topography. One of the key aspects in obtaining reliable ground deformation prediction results is the determination of the edge effect offset. The value assigned to the edge effect corresponds to a virtual offsetting of boundary lines delineating the extracted panel to allow for roof cantilevering over the mined out area. The objective of this paper is to describe the methods implemented in updating the edge effect offset code within SDPS. Using known geometric equations, the newly developed code provides a more robust calculation of the offset boundary line of the extracted panel for simplistic, as well as more complex, mining geometries. Assuming that an extracted panel is represented by a closed polyline, the new edge offset algorithm calculates a polyline offset into the extracted panel by the user-defined edge effect offset distance. Surface deformations are then calculated using this adjusted panel geometry. The MATLAB® program was used for development and testing of the new edge effect offset feature. In completing rigorous testing regimes, the new offset features will be integrated into SDPS, further increasing the speed and reliability of the programs resulting in a retrospective increase in capability and flexibility. INTRODUCTION Underground operations have been known to cause mining-induced subsidence inside and outside of the mine permit area (Karmis, Agioutantis, and Andrews, 2008). Additionally, subsidence can impact surface water bodies, such as rivers, streams, lakes, and wetlands (Karmis and Agioutantis, 2015; Newman et al., 2016), as well as infrastructure, such as roads, railroads, pipelines, and buildings. With an increase in regulatory focus on mining-induced impacts to local structures, the calculation of mining-induced subsidence indices has become necessary in determining potential damage and mitigation efforts. The accurate prediction and evaluation of mining-induced ground deformations is required to obtain underground mining permits due to potential impacts to nearby structures, as well as hydrogeological sources. The prediction of ground deformation indices is often a complex task due to the number of input parameters required, such as mining geometries, overburden lithology, surface topography, the rate of mining (Karmis, Agioutantis, and Andrews, 2008)."

Jan 1, 2017

By Ali Porbaha

The use of soil nailing technology as a cost effective alternative for excavation support and slope stabilization has substantially increased in the United States during the last decade. For example, in the past thirteen years, more than 185,800 square meters of soil nail walls have been constructed in California alone. The conventional soil nail systems pose difficulties when ground conditions are subject to caving, for instance for silty sand (sugar sand) or cobbles and boulders. The construction industry has developed self drilling hollow bar systems (or pressure injected bored, IBO) that combine both drilling, placing and grouting in a single operation as a solution to speed up construction. While the system is extensively used for temporary applications, nevertheless, some concerns, particularly about corrosion, has limited the use of this technology as a permanent system in North America. This study presents several issues related to self drilling soil nail systems, the results of a field investigation and a summary of the research project.

Jan 1, 2006

By Michelle Mangione, John Kuyt, Zili Li, Michael Mooney

"Twin bored tunnels are commonly used for a variety of road and tunnel projects throughout the world.A major component of these twin tunnel projects is the construction of connecting cross passages that provide emergency access between tunnels and space for tunnel service equipment. Cross passages can present significant geotechnical risk and technical challenges to a project – support systems must be considered for redistributing loads around the mainline tunnel openings and supporting new loading resulting from excavation activities. Additionally, cross passages pose risks to construction schedule and cost because of their sequencing at the end of construction, so mitigation of schedule overruns can be critical. By observing field instrumentation data records from completed projects, a better understanding of the force development in each temporary structure can be achieved with indication of which structures are the most critical to support ground loads.This article discusses the data obtained during the Brisbane Airport Link construction project, a road tunnel located in Brisbane, Australia. Strain gauge instrumentation data from the precast segmental lining and propped opening steel sets is presented with relation to the construction sequence and local geology. Interpretations and conclusions based on the observed trends are proposed, with several key mechanisms affecting the loading and unloading identified.Brisbane Airport Link project overview. The Brisbane Airport Link project in Brisbane, Australia, connects central Brisbane to the airport located northeast of the downtown with more than 7 km (4 miles) of twin-bore road tunnels, two lanes each, with several caverns, interchanges and access ramps constructed along the alignment to connect to other key routes in the city. The project was executed under a public-private partnership (P3) scheme, funded and operated by the consortium BrisConnections. The main contractors were a joint venture of John Holland and Theiss, while the design was carried out by Arup and Parsons Brinckerhoff.Construction of the tunnels was conducted using a combination of 17 roadheaders and two 12.5-m (41-ft) double-shield Herrenknecht tunnel boring machines (TBM) (Harding & Francis, 2013). The TBMs were used in earth pressure balance- (EPB) type closed mode for the initial portion of their drive, starting at the northeast end of the alignment. Tunneling started in soft ground, weathered rock, and mixed face conditions initially, progressing to competent sedimentary rocks as the drive continued. Support was accomplished using a 12.1-m (39.8-ft) diameter steel fiber reinforced concrete (SFRC) segmental lining installed behind the TBMs in nine segments + one key arrangement. The innovative design of these segments is detailed in the paper by Harding and Francis (Harding & Francis, 2013). Ancillary roads and underground interchange caverns were constructed by sequential excavation techniques using roadheaders, accounting for nearly half of the total underground excavations."

Mar 1, 2017

The Olympic Dam copper-uranium-gold-silver deposit, located 520 km NNW of Adelaide, S.A. was discovered by Western Mining Corporation Ltd in 1975, and is now being developed as a joint venture between WMC (5107o) and the BP Group (4907o). The discovery of this deposit resulted from the application of a conceptual model for the formation of sediment-hosted copper deposits. This model postulated that the oxidation of basaltic rocks could release significant amounts of copper into solution and that, under favourable conditions, these solutions might pass upwards along faults, and the copper be precipitated in reduced- facies sediments higher in the sequence. The Stuart Shelf province was chosen for exploration because geological interpretation suggested the presence of suitable basal- tic source rocks at depth, and favourable host sedimentary rocks in the overlying sequence. The Olympic Dam site was selected for drill-testing because of the presence of coincident gravity and aeromagnetic anomalies suggesting the presence of basalts and/or mineralisation at depth. This site also had a favourable tectonic signature, indicating the presence of deep crustal structures which might have allowed fluid migration.

Jan 1, 1988

By S. Tan

In this paper, several commonly used computer truck dispatching criteria are evaluated. A computer-oriented truck dispatching and production simulator was developed to provide data for comprehensive cross comparison among the dispatching criteria. The definitions, primary considerations, characteristics, and performances of these dispatching criteria were investigated. From the simulation results, it was concluded that, in general, no one criterion can dominate all others. All basic dispatching criteria including minimizing truck waiting time, minimizing shovel waiting time, minimizing truck saturation, maximizing truck momentary productivity, or truck routes optimization provide a local optimal solution. To obtain a direct global optimization solution for this complex stochastic process does not appear to be likely. Therefore, the search for an optimal dispatching criterion that will fit all conditions may not be realistic. However, based on the simulation results of the mine operation, several dispatching criteria which have good potential to increase performance can be selected. It may be necessary to search for the best combination of these truck dispatching criteria for a given situation. For example, a truck flow measurement such as the truck clustering factor at shovels can be used as a switch parameter to change from one criterion to another. The values for the switch parameter at which actions should be taken to change the criterion can be established through simulation programs.

Jan 1, 1992

By Eggleton T, Taylor G

The lateral and vertical distributions of gold and a wide range of other elements in the regolith, close to Au and Cu mineralisation have been investigated at Goonumbla, NSW. Open cut mining has exposed deeply weathered profiles which have been used for this investigation. Determination of secondary mineralogy and micromorphology of profiles have facilitated the broad interpretation of processes that determine element mobility and dispersion from primary mineralisation as a result of weathering. This in turn has led to better interpretation of geochemical data and enhanced understanding and knowledge of regolith geochemical processes which are invaluable in the formulation of improved exploration Procedures.

Jan 1, 1997

By Pedro Hugo Tumialán de la Cruz

Dado que el Perú es uno de los países que cuenta con muchos recursos de yacimientos polimetálicos, el presente texto señala los aspectos que comprenden su metalogenia. Dentro de la mineralización de polimetálicos tenemos los siguientes tipos de yacimientos: aquellos relacionados con inyección magmática de composición intermedia a félsica y a la posible inyección de magma ultrabásico, pórfidos de cobre-oro-molibdeno y de cobre-molibdeno, yacimientos de molibdeno, tipo skarn,de reemplazamiento y relleno en caliza, de diseminación de oro de grano muy fino en caliza tipo Carlín, de oro y plata en areniscas-cuarcitas-pizarras, los cordilleranos, de tungsteno, de estaño en intrusivo félsico, volcánicos continentales como los yacimientos filonianos epitermales de plata-oro, los diseminados de oro y plata de baja ley y alta sulfuración, de antimonio, diseminados de oro-plata en intrusivos de composición intermedia, los volcanogénicos marinos de sulfuros masivos tipo Kuroco, tipo Missippi Valley y los lavaderos de oro.Se considerancomo épocas metalogenéticas de estos yacimientos polimetálicos edades de mineralización del Pérmico, Cretáceo Medio, Cretáceo Superior, Paleógeno, Neógeno, Cuaternario.

Jan 1, 2014

By M. J. Ferrante

Low-temperature heat capacities and high-temperature enthalpies for syn¬thetic Cu2S and CuS were measured. This investigation is part of the Bureau of Mines goals to provide thermodynamic data essential to the more efficient processing of copper ores, and thereby minimize the current dislocations in energy, environment, and mineral supply. Heat capacities were measured with an adiabatic calorimeter from 5 to 310 K, and resulted in S°298 = 27.76 for Cu2S(c) and S°298 = 16.05 cal/deg mole for CuS(c). Low-temperature values are tabulated for Cp°, S°, -(G°-Ho°)/T, and H°-Ho°. Enthalpies were measured with a copper block calorimeter from 298.15 to 1,600 K for Cu2S(c,1) and 298.15 to 780 K for CuS(c). The thermal behavior of CuS showed no transitions or other significant anomalies for the low- or high-temperature investigations. Cu2S showed reversible transitions at 376 K with an isothermal heat absorption of 0.865 kcal/mole, 720 K with an isothermal absorption of 0.280 kcal/mole, and approximately 1,400 K (congruent melting point) with a heat of fusion of 3.070 kcal/mole. High-temperature data are tabulated for H°-H°298, Cp°, S°, and -(G°-H°298)/T. Enthalpies are also expressed in equation form. The low¬and high-temperature data were combined with data from the literature to cal¬culate and tabulate ?Hf°, ?Gf°, and log Kf as a function of temperature.

Jan 1, 1978

By Jacob Bummer, Greg Roset, Dayle Flynn

"IntroductionStillwater Mining Company operates a Precious Metals Smelter (PMS) located in Columbus, Montana USA. The PMS processes iron, copper, and nickel sulfide bearing concentrates containing platinum, palladium, gold, and rhodium. The concentrates are produced from two mines in the Beartooth Mountains located in south central Montana. The PMS utilizes a 7.5 megawatt 3-in line electric furnace to smelt the concentrates, and two Top Blown Rotary Converters (TBRC's) to remove iron. In addition to the mine concentrates, the PMS also processes various forms of Platinum Group Metal (PGM) bearing recycled catalyst. The sulfide matte produced within the electric furnace and TBRC's acts as a collector for the PGMs. Throughout the operation of the PMS, there are three different forms of molten material that are processed through the Stillwater Granulation system: TBRC matte, TBRC slag, and electric furnace matte. This paper describes the operation of this granulation system.Tapping the FurnaceWhen a sufficient level of molten PGM bearing matte has been reached within the inner volume of the electric furnace, the molten material is ""Tapped"". Tapping requires drilling into the electric furnace until reaching the molten matte phase. The matte phase will drain out of the drilled hole through a graphite launder into a 5 ton refractory lined ladle. Once the ladle is full, the tap is plugged with a mud gun."

Jan 1, 2012

By A. W. Khair, S. J. Jung

"IntroductionIn a typical incremental loading test, the AE activity increases rapidly in the initial stage of the loading. It is associated with initial closure under compression of favorably oriented cracks already present, together with sliding of crack faces against each other /1/. After the initial stage, crack closure and movement largely cease and the AE activity drops to a barely detectable level /2/. In the final stage of loading test, cracking associated with the onset of inelastic deformation' occurs, and the rate of AE rapidly increases /3/ indicating an increase in the •number of events associated with higher number of microcracks. To understand better primary fragmentation process, Anderson and Ruzzi conducted tests to identify a practical method of monitoring fracture development in rock, as caused by an excavation tool /4/. They proved that a relationship existed between the AE activity, generated during fracturing and the amount of fracture surface area created.A process of fragmentation, demonstrated by conical bits acting orthogonal to the flat surface of block of coal specimen with and without lateral confining pressure is presented here. The monitoring of AE during the fracturing process of rock/coal has been a very useful indirect method in studying fracture mechanism.Specimen PreparationLarge blocks of Waynesburg coal were obtained from a surface mine. These blocks were then out and molded to approximate dimensions of 25.4 x 25.4 x 15.2 'an (10 x 10 x 6 in.). These specimens were instrumented with three strain gages in a 45 degree rosette. One was mounted parallel to the bedding plane direction, another was tinted at an angle of 45 degree from the bedding plane direction and the third was mounted perpendicular to the bedding .plane direction. Each of the three strain gages were set 5.1 an (2 in.) away from the impact point.Typical Test ProcedureIn a typical experiment, the specimen was placed in the confining chamber.Predetermined equivalent in-situ stresses were applied to the specimen by using two sets of hydraulic cylinders. Two 1 in. thick steel plates ware positioned between the sample and the hydraulic cylinders in order to distribute the pressure uniformly over the whole surface of the specimen. The LVDT null position was adjusted with respect to the coal face. After setting the LVDT, the bit and associated weight was lifted to a predetermined height (equivalent to a predetermined kinetic energy) by a win. The three strain gages were balanced using the signal conditioner and the output was recorded by a 6 channel strip chart recorder. The experimental set-up is shown in Figure 1."

Jan 1, 1989

By James Stenhouse

Abstract The aqueous oxidation of pyrite in caustic solutions under oxygen pressure was investigated by measuring that effect of reaction variable on oxygen consumption by the reactions. From the results of this investigation, a model for the process has been proposed. In this model, sulphur diffuses as a positive ion through an oxide layer which forms on the sulphide particles and is then oxidized to sulphate ion. Iron is oxidized by substitutional diffusion of oxygen atoms into the oxide layer. The effect of most reaction variables on the rate of oxygen consumption can be explained with this model. Introduction Recent investigations (1,2,3) have shown that certain sulphide ores can be readily leached by agitating the ore in the form of a pulp under pressure in the presence of oxygen. Since very little was known of the mechanism of this oxidation, a programme of investigation was inaugurated in 1949 in the laboratories of the Department of Mining and Metallurgy of the University of British Columbia. Financial support for the investigation was received from the National Research Council in the form of student grants and bursaries, from the Canadian Liquid Air Company, Limited, and from the Consolidated Mining and Smelting Company of Canada, Limited. The first objective was to devise a technique to study the primary oxidation reactions in aqueous solutions and to apply the technique to a detailed study of the oxidation of pyrite in caustic solutions.

Jan 1, 1952

By W. C. Hellyer, R. A. Campbell

In single-stage autogenous grinding, the buildup of a critical size fraction in the media can be corrected by removing this material through pebble ports, crushing it below the critical size range, and recycling the crusher product back to the mill. The rate at which the critical sire fraction is crushed affects the size distribution of the grinding media and this in turn affects the sire distribution of the grate discharge. This provides a means for controlling the grind produced by a single-stage autogenous grinding unit. The pilot-plant investigations on a very hard copper ore were carried out at the facilities of the Institute of Mineral Research, Michigan Technological University. In an autogenous grinding circuit in which feed at approximately 9 in. top size is reduced to a size suitable for subsequent processing, the build-up of a "critical size" fraction in the media causes problems. A "critical size" fraction has been defined as, "media too small to effect reduction by impact grinding of ore coarser than a quarter of an inch and too large to be broken by the largest size of media in the charge."' The buildup of a critical size fraction reduces the capacity of the mill, increases the grinding power requirements per ton of finished product, and generally produces a finer grind than is desired. It is general practice to overcome this problem by the addition of large-diameter steel balls to the grinding charge. This has certain disadvantages, such as 1) an increase in mill liner wear, 2) wear on the steel balls, and 3) some loss in flexibility in grinding circuit opera-tions resulting from difficulties in removing the steel balls by means other than by grinding out. A number of investigators' have suggested the use of a small crusher as an alternative to the use of large steel balls for control of a critical size fraction. With this technique the critical size fraction is removed from the mill continuously through suitable-sized pebble ports, crushed below the critical size range, and returned to the mill. An external crusher would cause no increase in mill liner wear, the wear on the crusher would be less expensive than the wear on the steel balls, and the flexibility of the grinding circuit operations would be enhanced since the crusher can be cut into and out of the circuit at will. This paper describes an autogenous grinding pilot plant investigation on a very hard copper ore, which led to the selection of an autogenous grinding flowsheet incorporating a crusher in the circuit as the preferred method for grinding this ore. Further development of the technique demonstrated that the crusher could be employed to control the product produced by an autogenous grinding unit. Description of Pilot Plant These investigations were carried out at the pilot-plant facilities of the Institute of Mineral Research, Michigan Technological University, Houghton, Mich. The autogenous grinding unit was a 6-ft-diam by 2-ft-long Hardinge Cascade mill with %-in. slotted steel grates. Pebble ports cut into the grates allowed passage of pebbles having a top size of approximately 21/2 in. The grate and pebble-port discharge material passed over a 3/16-in, trommel screen with the trommel under -size being pumped to the classification device. DSM screens were employed for classification in the early investigations, but were replaced later by a small Dorr rake classifier. The trommel oversize material returned to the mill via scissor conveyors. When the crusher was incorporated into the circuit, the trommel oversize material passed to a double-deck vibrating screen fitted with 2-in. and 3/4-in. square mesh screen cloths. The $ 2-in. and the —2 +3/4-in. size fractions were combined and crushed to a nominal 1 in. in a 4 x 6-in. jaw crusher. The crusher discharge and the —3/4-in. screen undersize returned to the mill. In the final investigation, a flap gate fitted to the top deck of the screen directed the — 21/2 +2-in. size fraction to the crusher or back to the grinding mill. The flap gate operated manually on a 15-min cycle, with this material being crushed for so many minutes out of each cycle. This was found to be a more reliable method of controlling the amount of — 21/2 +2-in. material crushed than attempting to make a split of a small weight of material on a continuous basis. Operational Techniques: Each sample was sized into three fractions and the Cascade mill feed was reconstituted from these size fractions in the proportions existing in the original sample. Sufficient feed for 15 min operation was weighed out and fed by hand over a 15-min period. The gross mill power draft was recorded every 15 min, corrected for tare power and drive efficiency, and reported as net kilowatt-hours per ton. A recording kilo-watt-hour meter provided a continuous visual record of the power drawn by the mill. Pulp densities of the trommel undersize and the classifier overflow (or DSM undersize) were taken every 15 min. The classifier overflow was sampled automatically. Timed samples of the classifier sands were taken every 15 or 30 min, weighed, and returned to the circuit. After correcting for moisture content, the weights were converted into percent circulating load. Timed samples of the +2 in., the —2 + 3/4-in., —3/4-in. screen fractions, and the crusher discharge, were

Jan 1, 1971