Search Documents

By Clinton Strachan, Rob Dorey

10.1 INTRODUCTION This chapter presents considerations which should be applied to heap leach pad site selection, site evaluation, and design, relative to the geotechnics of the site and ore. 10.1.1 General Guidelines are presented covering the topics encountered in design and construction of heap leach faci1ities. Because geotechnical characteristics vary from site to site, not all geotechnical topics associated with a specific heap leach facility are presented, and there may be exceptions to some of these guidelines. The general features of a heap leach facility (from Chapter 1) to be discussed in this chapter are: • Leach pad (including leach pad foundation and liner); • Heap; • Solution storage faci1ities (for pregnant and barren process solutions) ; and • Solution collection facilities (which collect and convey solutions in the heap and convey them to solution storage facilities). These general features are illustrated in Figure 10.1. Liners for these facilities are discussed in Chapter 11. Solution application systems and the sizing aspects of solution storage facilities are discussed in Chapters 6, 7, and 12. The general features listed above are constructed with and overlie naturally occurring materials (such as ore, borrow soils, and subsurface soils and rock). These natural materials are relied upon to perform in an acceptable manner as a component of the leach facility (such as the liner, drain material, and foundation).

Jan 1, 1988

By K. R. Gardner, P. B. Altringer, R. H. Lien

The Bureau of Mines, U. S. Department of the Interior, is investigating biological and chemical reduction of selenate and selenite from waste waters. A mixed bacterial culture, isolated from agricultural waters, removed selenium from four oxidized cyanide solutions from precious metals operations containing 0.6 to 30 ppm Se and 13 ppm CN. Up to 85% selenium removal was attained using bacteria under controlled batch conditions in a 3-L stirred tank reactor and in small-scale continuous tests conducted in a rotating biological contactor (RBC). Fe(OH), reduction of the selenium reduced the effluent concentration to 0.02 ppm Se; however, the reagent costs were prohibitive. A final processing scheme may involve a combination of biological and chemical treatments.

Jan 1, 1991

By Jr. Gambrell

Support characteristics of in-cycle trusses are analyzed using a photo-elastic model loaded by tightening a truss in the sequence normally used in an underground mine. Stresses in the roof at its center point and at the junction of the roof and rib are examined. Effects of zero tension and unequal tension in the inclined anchor rods are presented. Effects of simulated subsidence on stress in the roof surface and on tension in the separate truss members are examined. Conclusions are drawn relating to (1) the effects of tension in the inclined anchor rods on uplift and compressive stress parallel to the roof surface, (2) the effects of subsidence on stress in the roof surface and, (3) the effects of subsidence on tension in the truss members.

Jan 1, 1989

By W. T. Turrall, D. Porter

The paper describes a machine developed for the purpose of concentrating clear optical grade fluorspar crystal from a feed material containing less than 1 pct impurities. The principle of concentration is based on the fact that in a liquid having an index of refraction equal to that of fluorite (n — 1.434) clear crystals are invisible, whereas crystals containing occluded impurities absorb a part of the light. As the crystals pass through a light beam, undesired crystals give themselves away by creating a shadow on a photoelectric receiver. .The shadow is converted by the photoelectric cell into an electric pulse. An electronic circuit amplifies this pulse and commands the operation of a mechanical concentrator. Hp HE crystal laboratory, Dept. of Physics, Massa--*- chusetts lnstitute of Technology, was confronted with the problem of obtaining a supply of optical grade calcium fluoride (CaF,) for use in growing synthetic CaF, crystals. A search of the known fluorspar deposits did not indicate that any quantity of optical spar could be obtained. Even the best material had to be sorted by hand to remove impurities. The process for growing CaF, crystals developed by Professor D. C. Stockbarger of the Dept. of Physics, M.I.T., necessitates very pure feed materials. Exclusion of impurities is required, even in amounts detectable only spectrographically. The impurities occurred as minute inclusions of SiO,, BaSO,, CaCO,, FeS2, water or air. Crystals up to 4 in. in diam and weighing several pounds are made by the Harshaw Chemical Co. in Cleveland. Since the time required to grow a 4-in. crystal is about one week, and since the cost of manufacture is high, removal of impurities by any concentration method appeared practical. The mineral engineering section of the Dept. of Metallurgy undertook to investigate the possibility of concentrating clear optical fluorspar, —4 mesh + 10 mesh, from a feed containing over 99 pct CaF,. Various innovations of the known methods of concentration were considered, but in each case the minute amount of impurities associated with the crystal produced such extremely small differences

Jan 1, 1953

By F. Concha

A robust theory of sedimentation-consolidation evolved and was accepted by researchers world-wide in the last two decades of the 20th century. This theory provides a reliable method of thickener design and simulation. However, a process model, simple or sophisticated, empirical or phenomenological, is useful only if it is possible to determine, in an objective way, its experimental parameters. Research workers at the University of Concepción, together with Cettem Mineral Technology Center, created an integrated system of thickener design, simulation and control, including instrumentation, algorithm and software, which can be used by personnel in industry without specialized knowledge of thickening theory. In the paper, the development of three instruments for the measurement of pulp concentration, solid flux density and sediment compressibility is described. Each instrument uses software for data input, parameter calculation and results display. The paper also describes software for the optimization of the experimental parameter and for the design and simulation of industrial thickeners. Finally, mathematical algorithm and control strategies based on the phenomenological model are presented and compared with classical feedback control.

Jan 1, 2014

By Kevin MacPherson

After 34km of roof bolted drivage the first fall of ground occurred at the Phalen Colliery in the maingate of the 8th East longwall panel. The fall occurred over the stage loader as the wall approached an area of poor roof geology. This area had developed a severe cutter since initial drivage and the longwall had yet to mine through 500m of even worse conditions. This paper describes the cause of the poor roof conditions, the use of polyurethane resin injection and cable bolting to re-stabilize the roof outby the fall, and the measurement of roof movement and performance subsequent to the continuation of mining under the rehabilitated roof.

Jan 1, 1999

By J. Tomlinson

Shuttle car trailing cable splices were tested for resistance to failure upon being subjected to repeated bending, abrasion, and tensile shocks using a new testing method that closely simulates shuttle car induced stress. The results show that under normal stresses, splices can be made to withstand the equivalent of three months of operational use. Restoring the tensile strength to the conductors is found to be as critical as restoring flexibility. Splices in which the conductors are of slightly unequal length did not present as serious a workmanship problem as previously thought since test results show that the conductors tend to equalize when longer cables, in contrast to short cables employed in previous testing methods, were used. Dynamic recordings of cable tensile stresses are presented for a shuttle car and the new simulated testing method. Two simple but effective methods for removing insulation using a knife and a pair of pliers are described. None of the designs tested for a sacrificial splice covering were satisfactory.

Jan 1, 1979

The 1932 meeting will be held June 8, 9 and 10 in the western section, place to be announced later. If you have any suggestions for the place or program; send them to the Secretary at once.

Jan 1, 1931

By Richard T. Ely

Conservation, narrowly and strictly considered, means the preservation in unimpaired efficiency of the resources of the earth; or in a condition so nearly unimpaired as the nature of the case, or wise exhaustion, admits. And broadly considered, it means more than the word itself implies, for it naturally includes an examination of methods whereby the natural inheritance of the human race may be improved; and still more broadly considered—and as used in popular discussion—it includes a treatment of the effects of productive conservation measures upon distribution. We shall give our attention briefly to the main points in this informal definition before we pass on to the thesis that conservation is largely a matter of property relations—-that a wise conservation policy means wise property relations.

Jan 1, 1916

By Thomas M. Keevin, Gregory L. Hempen, David J. Schaeffer

In an attempt to reduce the potential for fish mortality during the explosive demolition of Locks and Dam 26, Mississippi River, the U.S. Army Corps of Engineers, St. Louis District explored the use of a bubble curtain to reduce the fish kill radius of underwater explosions. Bubble curtains are walls of bubbles rising from a bottom-resting bubbler manifold supplied with compressed air. Demolition engineers have long been aware of the attenuating properties of air bubbles in water. As such, air curtains have been routinely used to protect underwater structures from damage by underwater explosive shock waves. However, their use in protecting aquatic resources during full-scale explosive demolition projects was untested.

Jan 1, 1997

By M. J. Meulendyke

An extensive program of marked ball wear testing (MBWT), laboratory corrosion studies, and worn ball surface analyses has been used to gain insight about the role of corrosion in the overall wear process. In some environments, localized corrosion is observed; the actual wear mechanisms in such cases are pitting/spalling and abrasion. Factors affecting the occurrence of pitting include the abrasiveness of the ore, corrosivity of the slurry, corrosion resistance of the media, and galvanic coupling effects. Elimination of pitting substantially improves overall wear resistance. When pitting is not observed, the contributions of general corrosion are significantly less.

Jan 1, 1984

The Wednesday morning session was opened by President Joe Ward at 9:30 a.m. He complimented Walter Mueller, Program Chairman, for the excellent job he did as head of that very important committee. He also thanked all those on the various committees, speakers, and all who participated in making the 1972 meeting a success. He called on William S. Landers, Chairman of the Auditing Committee, to give his report. He read the report and asked for a motion of approval. Motion was made, seconded and approved. (See Treasurer's report on page 5.) A. E. Pagnotta of the Resolutions Committee read their report as follows: RESOLVED: Whereas, since the 67th Regular Meeting of the Rocky Mountain Coal Mining Institute. held at Park City, Utah, the Institute and the coal mining .industry has suffered the loss through death of service and fellowship of the following members: W. H. Carson James Dalrymple Edward H. Denny A. B. Foulger Thomas E. Graham G. R. Harris Frank Markosek Anthony C. Moschetti Harry Swihart Franklin B. Thomas

Jan 1, 1972

By O. P. Burghardt

Blast furnaces of high specific throughput capacities producing 10,000 tpd of pig iron or even more, require burden materials which, because of their chemical, physical and metallurgical properties, guarantee such high performances. Meanwhile, it should be generally accepted that for evaluating the quality of iron ore pellets, it is not sufficient to know the chemical analysis and the physical properties, i.e. grain size distribution, cold compression strength and abrasion of the fired pellets. It is indispensable to determine the metallurgical properties indicated by swelling, reduction-softening under load and reducibility, as well as grain disintegration in the low-temperature range in the beginning of reduction. By introducing new test methods, and in the face of the need to meet more strict requirements, pellet producers are being confronted with steadily increasing tasks and problems which require a deepening of our knowledge of the ways and means of making high-quality iron ore pellets.

Jan 1, 1975

By J. Groppo, W. Zhang, R. Honaker

"The flotation of monazite is depressed when using hydroxamic acid as a collector in the presence of calcium ions which may exist due to the dissolution of minerals such as calcite. Minor dosages of sodium hexametaphosphate (SHMP) were found to effectively depress calcite, whereas the flotation of monazite was not impaired in single mineral flotation tests. However, in a mixed mineral flotation system, monazite flotation was depressed significantly. The mechanism of hydroxamate adsorption on monazite and calcite, the depression mechanism of calcite on monazite, as well as the depression mechanism of SHMP on calcite and monazite were studied using micro-flotation, electro-kinetic, and adsorption tests. Findings indicate that the adsorption of hydroxamate on monazite was due to chemisorption while adsorption on calcite was a result of physical interaction. SHMP significantly increased the negative charges of calcite surfaces which depressed the adsorption of the hydroxamate anions on the calcite surfaces due to an elevated electrostatic repulsion force. When calcium-rich minerals such as calcite are mixed with monazite, the calcium ions dissolved from the mineral surfaces specifically adsorb onto the phosphate oxygen sites on the monazite mineral surfaces thereby causing depressing effects. The addition of SHMP to suppress collector adsorption on the calcite surfaces interacts with the calcium species that were specifically adsorbed onto the monazite surface, which prevents hydroxamic acid adsorption onto the rare earth oxygen sites due steric hindrance and results in the flotation depression of monazite. INTRODUCTIONAs one of the commercial rare earth ores, monazite has been widely exploited to produce additives for catalysts, batteries, alloys, etc. Because of the complexity and the fine nature of some monazite ores, methods such as gravity, magnetic, and electrostatic separation to treat beach sand monazite fail to produce satisfactory concentrates, suggesting the use of floatation is warranted (Cheng, Holtham, & Tran, 1993). The primary associated minerals of monazite ores include ilmenite, quartz, zircon, rutile, sillimanite (Dixit & Biswas, 1969; Pavez a& Peres, 1994, 1993). Using sodium oleate as collector for monazite has been reported in many studies (Cheng et al., 1993; Dixit & Biswas, 1969; Pavez & Peres, 1994, 1993). Several investigations have reported maximum floatability of monazite occurring at pH values between 8 and 9 (Cheng et al., 1993; Dixit & Biswas, 1969). A study conducted by Pavez and Peres (1994) compared the use of hydroxamate and sodium oleate for the treatment of a monazite ore and found that hydroxamate significantly improved the grade of rougher concentrate."

Jan 1, 2016

By C. Zangerl, T. Strauhal, S. Perzlmeier, M. Holzmann

"In high mountainous regions, deep-seated rock slides are often observed in foliated metamorphic rocks such as paragneisses, micaschists and phyllites. Given that comprehensive investigations of deepseated rock slides are extraordinary costly and therefore are rare, most studies are related to investigations in the surroundings of infrastructures and human settlements. In the framework of this study there is an excellent opportunity to gain new insights in the fundamental processes and mechanisms of slowly moving deep-seated rock slides from a case study in the surrounding of a large dam reservoir in Austria. New fundamentals for comprehensive slope stability analyses and hazard assessments and sound prognoses focussing on the long-term stability and deformation behaviour of slopes under changing boundary conditions (e.g. impounding of a reservoir) and/or concepts for mitigation measures can be obtained. Within this contribution, geological field surveys, deformation monitoring, geophysical and drilling data were analysed and presented. Based on the compiled and analysed data, some key-properties of the rock slide will be presented, whereby special attention will be given on the geometry and internal structure, the slope kinematics, as well as hydrogeological and geomechanical aspects.INTRODUCTIONIn high mountainous regions, deep-seated rock slides are often encountered in highly foliated metamorphic rocks such as paragneisses, micaschists and phyllites (Agliardi et al. 2012). Critical situations may occur when deep-seated rock slides fail in a rapid manner characterised by very high sliding velocities, and/or when they develop into long run-out rock avalanches. However, many rock slides in foliated crystalline rock masses either do not move at high velocities nor do they accelerate seriously and form extremely rapid slides. Displacement rates in the range of a few millimetres or centimetres per year are common for this type of rock slide (Bonzanigo et al. 2007, Tentschert 1998, Watson et al. 2007). Nevertheless, some case studies show an activity behaviour characterised by acceleration phases reaching velocities of even metres per day. However a slope collapse is not expected and these slopes decelerate to much lower base activities. The trigger for these phases can be manifold and include heavy rainfall and snow melt, initial reservoir impounding and water level fluctuations, changes in the slope’s equilibrium state due to antecedent slow deformation processes, ongoing erosion processes along the toe of the slope, and others (Zangerl et al. 2010)."

Jan 1, 2015

By Abhilash

Uranium is conventionally extracted using a process that employs strong acid (H2SO4) and an oxidant (MnO2) as leaching agents. This method often creates environmental problems, requires large amounts of energy, and involves a complex operational plant. It is not, however, economically attractive to extract uranium from low-grade ores by chemical leaching. Because the content of U3O8 in the Indian ore is usually below 0.1% by weight, it is necessary to develop an alternative process to enable the efficient and economic recovery of uranium. Uranium ore from the Narwapahar mines, UCIL is a type of vein deposit found in India, which accounts for ~54% in India. The ore (0.047% U3O8), though of Singhbhum area, possess exceptionally different mineralogy due to presence of some refractory minerals and richness of apatite (5%) resulting in a maximum 78% recovery through conventional processing at UCIL, with a very high consumption of sulfuric acid and pyrolusite, besides possible loss of uranium as uranium phosphate. To avoid usage of environmentally non-benign oxidants, remediation of influence of phosphates, and improve the overall process output of uranium; an alternate extraction technology using microbial isolate(s) is worthwhile exploring and the same is presented in the paper. The microbial isolate enriched with Acidithiobacillus ferrooxidans grown from source mine water was employed for bio-leaching of uranium while varying pH, pulp density (PD), particle size, etc. On varying pH at 35oC using 20%(w/v) PD and <75µm particle size, 83.5% and 78% uranium bio-recovery were observed at 1.7 and 2.0 pH in 40 days against maximum recovery of 46% and 41% metal in control experiments respectively. Whereas, it was observed that grinding of ore to finer size actually helped dissolution of uranium. Finer size particles (<45µm) gave a maximum biorecovery of 93% in 40days at 10%(w/v) PD, 1.7 pH and 35oC. The bio-recovery of uranium fell down from 93% to 82.73% and 60% on increasing the pulp density from 10% to 20% and 30% respectively for particles of <45µm size. The higher uranium dissolution during bioleaching at 1.7pH can be correlated with increase in redox potential from 433 mV to 664mV in 40 days.

Aug 1, 2010

By Finlayson E, Hilyard D, Francis G

Papua New Guinea&apos;s mainland is dominated by a foreland thrust belt, which can be divided into two zones. The "body" zone is floored by Palaeozoic granites and metamorphics of the Fly Platform (Tasman Orogen). Underlying the "tail" zone is Papuan Plateau, rifted from the Tasman Orogen during Coral Sea spreading, and believed to underlie the Papuan Peninsula and Papuan Islands region (D&apos;Entrecasteaux, Woodlark, Misima, Sudest, and Rossel Islands). Thrusting began in the Miocene and continues today in the crust below the "body" zone. The youngest known thrusted rocks in the "tail" zone are Pliocene in age. Recognition of foreland thrusting has major implications for petroleum prospectivity of the Papuan and North New Guinea Basins, mineral exploration prospectivity, and geological terrane identification in PNG.

Jan 1, 1987

Dr. Arthur H. Elliott has been connected with the gas industry for upward of thirty-eight years and was a chemist to whom the industry is deeply indebted for the application of the science of chemistry to its problems and processes. He was born in London, England, in 1851, and was the son-of a physician. While a child he was taken to France, where he received his early education, learning to speak the French language before his native English. His father having destined him for the medical profession, he commenced his studies on his return to England, but his attention being attracted to chemistry, he gave up the study of medicine to pursue that of chemistry. While still a student, he obtained a reputation as an iron and steel analyst, publishing two methods of analysis, one for the determination of sulphur .and the other for the determination of carbon in cast iron. On his graduation from the School of Mines at South Kensington, he left England intending to go to Australia, where an uncle resided, having in mind also the possibility of a trip to China. On his arrival in New York, he met Professor Charles F. Chandler, to whom he had a letter of introduction, and who induced young Elliott to remain. He graduated from Columbia College with the degree of Doctor of Philosophy in 1883. He became demonstrator in chemistry at the College of Pharmacy and afterward professor of chemistry and physics at the same college. He became connected with the Municipal Gas Lighting Co. in May, 1880. In. November, 1.884, when consolidation took place, he became engineer-chemist of the Consolidated Gas Co., which position he held until May, 1910, when he resigned, but was retained as consulting chemist until his death. Recently Columbia University conferred on him the honorary degree of Master of Science.

Jan 7, 1918

The co-operation of the members of the Institute is earnestly sought by the Committee on Nominations, recently appointed by the Board of . Directors, in its work of formulating a ticket for officers and places falling vacant in the Board of Directors in February, 1916. The Committee must present the official ticket of nominations to the Board of Directors at its October meeting. Members are, therefore, urged to send promptly their nominations for officers and Directors in order that the Committee may have an opportunity to give them full consideration. The officers to be elected at the annual meeting in February, 1916, are: One officer, known as Director and President. Two officers, known as Director and Vice-President. Five officers, known as Director; The attention of members is called to Articles V and VII of the Constitution, and to By-Law XIII, which reads as follows: "The geographical districts to be considered by the Committee on Nominations shall he as follows, until otherwise ordered by the Board. District No. 1. New England, New York, and New Jersey, excepting New York City and district., which is provided for in the Constitution. (N. B.-New York City and district is designated District 0.) District No. 2. Pennsylvania. District No. 3. Ohio, Indiana, Illinois, Iowa, and Missouri. District No. 4. Minnesota, Wisconsin, and Michigan. District No. 5. Montana, North and South Dakota, Wyoming, Nebraska, Kansas, Washington, Oregon, Idaho, and Alaska. District No. 6. California and Nevada. District No. 7. Utah, Colorado, Arizona, and New Mexico. District No. 8. Louisiana and Texas. District No. 9. Other Southern States and District of Columbia. District No. 10. Mexico. District No. 11. Canada."

Jan 7, 1915

By M. Selamat, J. Nirdosh, S. V. Muthuswami

High-grade uranium ores of Cluff Lake and Key Lake mines from the province of Saskatchewan in Canada are treated with nitric and hydrochloric acids with the objective of leaching 230 Th and 226Ra simultaneously with uranium to produce environmentally safe mill tailings, h is found that optimum conditions for uranium leaching are 50°C, 4 h, 30% solids in leach slurry and an acid concentration of 1 mol/L for HNO, for both the ores. In the case of HCl, a 3 mol/L acid concentration is needed and addition of an oxidant is required because otherwise 230Th and 226Ra extractions remain poor.

Jan 1, 1990