Search Documents

By Spencer PA, Winborne DA

The Porgera mineral deposit in Papua-New Guinea contains gold as finely divided, probably submicroscopic (1 um) particles dispersed in a pyrite sulphide matrix. Only 25-30% of the gold in pyrite can be extracted by direct cyanide leaching and fine grinding the pyrite does not increase gold extraction significantly. This work is concerned with the application of alkaline leaching at atmospheric pressure to oxidise the pyrite prior to gold recovery by cyanidation. The paper presents and discusses results of a comprehensive set of testwork using sodium carbonate, sodium hydroxide and calcium hydroxide alkaline media. Best results, at 60-70% gold extraction, were obtained with sodium hydroxide systems.

Jan 1, 1984

By James McManus

The original analogue instrumentation at Lornex Mining Corporation to optimize the throughput by controlling the power drawn by the semi-autogenous mills was found to be inadequate because of the frequent changes in ore type. Although the trunnion bearing pressure of the mill was a crucial control criterion, it was not utilized in the original control scheme. After several plant tests of different types of analogue controllers were unsuccessful in finding any control equipment suitable for this application, it was concluded that a digital process control computer was required. Computer control strategy to optimize the grinding rate by controlling the power and the bearing pressure of the semi-autogenous mill was developed and a Fox 2 /30 computer made by Foxboro was selected. After six months of experimentation, it was found that the throughput was increased substantially by computer control.

Jan 1, 1978

By P. Myllykoski, J. Nylander

"A commercial program package called Crownoff for the simulation of temper rolling in four high mills has been verified against measured data. The agreement between measured and calculated transversal strain distributions of the strip was found to be good. Effects of the strip crown and work roll bending force on the strain distribution were simulated. The results showed that when a single ground camber of work rolls is used for all strip widths; the strip crown should be parabolic, excluding the edge drop. An increase or decrease of the strip crown by 30 % during a coil can be compensated by a 2 to 5 t change in the work roll bending force. The ability to control the strip crown by work roll bending was insensitive to strip width. IntroductionCold rolled steel strips are usually temper rolled after recrystallization annealing, which follows cold rolling. The purpose of temper rolling is to suppress the yield point, finish the strip surface and correct possible flatness errors. The presence of a yield point might otherwise cause problems during subsequent forming processes. The in homogenous yielding in non-temper rolled steels leads to the formation of Lüders bands in the strip surface.The rolling force is influenced by the rolling speed and changes in frictional conditions in the roll bite. Therefore it is very important to plan carefully the mill settings and control algorithms during rolling. The purpose of mill control algorithms is to ensure constant reduction and the best possible strip flatness during the entire coil.Correctly predicting the rolling force is important for determining the mill presettings. Torque, forward slip and power requirements are not usually critical, if the reductions are small. However, the large elastic deformations occurring in the roll bite make the physical description of the process difficult. Physical rolling models developed for cold rolling contain assumptions that lose their validity as the reductions decrease to the level of one per cent."

Jan 1, 1994

By L. D. Tracy

"Introduction In the course of the investigations by the Bureau of Mines into the various causes of coal-mine explosions, the fact that several gas explosions had occurred during or very soon after a mine was being un-watered, attracted the attention of the Bureau's engineers. The apparent coincidence was so marked that there appears to be an extra hazard present, whenever water, which has been standing against the face of the coal for some time, is suddenly removed either by natural drainage or by mechanical means.Actual Occurrences Case 1. - A typical illustration of this hazard is shown in a gas explosion which occurred in a mine in Central Pennsylvania. Four main entries, 50 feet apart with an average grade of 6 per cent, had been driven with the dip of the coal, and from these mains 7 pairs of entries, at intervals of 800 feet, had been turned at such an angle that their grade was slightly rising. Prom these latter pairs of entries, rooms were turned practically at right angles.The main entries had been driven for 4,500 feet and at the face there was 400 feet of cover. As far as could be observed, the roof was of sandstone and the floor of clay.The coal bed being mined was the Lower Kittanning, which has a thickness of about 4 feet. A typical analysis of the coal in that section is as follows:"

Oct 1, 1924

By D. M. Larsen

Since start-up in 1985 the Cannon Mine has produced and shipped a 170 g Au/tonne (5 oz Au/ton) flotation concentrate to various smelters for gold and silver recovery. Several processed have been investigated to economically produce dore' at the mine site from the refractory concentrate. This paper describes recent laboratory and pilot scale test work utilized in the process design and engineering feasibility study of a 73 tonne/day (80 ton/day) pressure oxidation and CIL facility. The designed pressure oxidation circuit utilizes a series of vertical autoclave units operating at 170°C (338"F) and 1.4 MPa (200 psig). Projected operating costs are discussed.

Jan 1, 1993

By Charles H. Hopkins, J. M. Lohr

A COMMERCIAL development requiring a suitable alloy or alloys for sealing into various grades of glass made it desirable to have a more exact knowledge' of the expansion characteristics of the nickel-iron alloys than appeared in the published literature. The expansion of the more common [ ] types of glass under consideration varies from 2.7 to 10.4 X 10-s per degree Centigrade, over the range 20° to 400° C. For reference, the thermal expansion curves of several types of glass used for sealing by the lamp and tube industries are given (Figs. 1 and 2). This paper covers a detailed investigation of the thermal expansion of a series of nickel-iron alloys in which the nickel content varies from 30 to 70 per cent. Particular stress is laid on the alloys that contain between 40 and 55 per cent Ni.

Jan 1, 1938

By H. P. Allen

THE Achotla mill of the Cia. Minera de Peñoles is of special interest in that it is one of the few still employing the chloridization process. The ore milled comes from the Suriana mine and consists of both oxide and sulphide, from neither of which can the gold or silver be extracted by a simple cyanide treatment. The mill was built in 1927, after several years of study in the development of the process1, and operated from December of that year until October 1930. Operations were resumed in February 1935, and have been continuous since, treating approximately 5000 tons per month, while the mine is getting up to full tonnage of 6500 tons per month.

Jan 1, 1937

The Naval Consulting Board is asking the aid of all the members of the Institute in its effort to help solve the submarine problem. Probably every member of the Institute has some suggestion, and while each one of these may be of only slight value in furnishing the remedy, the aggregate may be of great service. Every member of the Institute will soon receive a pamphlet known as Bulletin No. 1 of the Naval Consulting. Board of the United States in which full information and instructions will be given to all of those who are willing to assist. It is hoped when this information is received the members of the Institute will give it their prompt attention and write as soon as possible to the Secretary of the Naval Consulting Board, 13 Park Row, New York, N. Y.

Jan 9, 1917

By D. Michael Holloway

The California Department of Transportation (CALTRANS) evaluated several pile foundation schemes for supporting the structures along the realignment of Interstate 880. The project replaces the double-decked (Cypress) viaduct collapsed in Oakland, California during the 1989 Loma Prieta Earthquake. Structural support demands led to the selection of steel pipe piles (16-, 24-, and 42-inch-(406-, 610- and 1067-mm-)diameter), filled with concrete and steel reinforcement. Deep penetrations required through layers of very dense/cemented sands in some locations, caused serious drivability and pile integrity concerns. The need for large pile driving hammers and large diameter steel pipe piles pushed the engineers well beyond local experience. Such questions as the feasibility of driving the pipes closed-ended through dense upper strata and quantifying the effects of installation on the long-term capacities of the piles led Caltrans to develop a comprehensive pile test program to address the design and construction issues effectively. The results were furnished to prospective bidders on the production stages of the ensuing contracts.

Jan 1, 1995

By A. W. Henderson

This investigation was performed to develop chlorination methods for extracting tungsten from scheelite and from an ore concentrate containing a mixture of scheelite and wolframite. On a laboratory scale with proper temperature control using elemental chlorine, over 90 percent extraction of tungsten is achieved. Carbon and sulfur dioxide were studied as reducing agents. The effects of salts such as calcium fluoride and sodium chloride were studied as additives to increase extraction and to reduce impurities in the volatile tungsten chloride product. Sodium chloride reacts with ferric chloride to form a nonvolatile double salt; whereas the chlorides and oxychlorides of tungsten are volatile and consequently condense free of iron. Separation of tungsten from molybdenum from an equal molar mixture was successful by fractionally distilling the oxygen-free chlorides and by selectively condensing the oxychlorides. Yields of 60 and 80 percent, respectively, were achieved for separating the less volatile tungsten chlorides containing less than 0.5 percent molybdenum.

Jan 1, 1965

By Raymond F. Dalton

Despite the ready availability of numerous zinc sources, the process of solvent extraction- electrowinning (SX-EW) has as yet found little favour in the zinc industry. It is suggested that this is largely due to the previous lack of availability of suitable selective reagents having the particular features required to enable them to fit in to a solvent extraction-electrowinning based process for zinc, particularly with regard to strength and selectivity for zinc over iron. This paper describes work on the development of new selective extractants for the recovery of zinc from both sulfate and chloride aqueous solutions and suggests how they might be integrated into new zinc processes.

Jan 1, 1994

Enable prospective in situ leach mine operators to evaluate the economic potential of an ore body by using a user-friendly, computerized in situ copper oxide leach mining cost model. Background As part of its research on in situ leach mining technology, the Bureau of Mines produced a 5-volume contract report that mining companies can use to design an in situ mining operation for copper oxide deposits. Written for the Bureau by the Science Applications International Corporation (SAIC) in 1988, the generic design manual also contains a computerized cost model for evaluating the economic feasibility of in situ leach mining for any specific copper oxide deposit. The cost model is to be used with Volume II of the contract report. But because of certain complexities associated with running it, the Bureau found that the model could be improved by making it more user friendly. Approach The approach taken by Bureau researchers to make the original model more user friendly was to incorporate a HELP function to define input parameters, and to enable the display of output on the monitor. An accompanying handbook, U.S. Bureau of Mines Information Circular (IC) 9284, contains further details on running, the 1990 model.

Jan 1, 1991

By P. Perruzza, R. Grandori, A. De Biase, A. Ciamei, A. Busillo

The Turin metro alluvium soil is mainly made of large boulders, cobbles and gravel , few sand and almost no fines. This grain size curve is out of the range of application for EPB and Slurry TBMs. In order to bore 5 of the total 7,5 kms of Line 1 tunnel, two specially designed Lovat EPB TBMs were utilised in combination with a systematic non structural pre-grouting of a small volume rectangular slab just above the tunnel section. The same pre-grouting was not however applicable for lack of access on surface in some sections of the remaining 2,5 km of tunnel that had to be bored below important buildings/structures, with under ground water pressure up to 1,5 bar, with curves radius of 180 m only. For these more critical sections it was necessary to study and implement a new technical solution and improve the capacity of the TBM to work efficiently in EPB mode even in this unsuitable ground and overall conditions. After months of studies the selected and adopted solution has been to inject inside the cutterhead chamber, in addition to the almost standard foams & polymers additive mixes, a suspension of limestone powders. This with the scope of compensating the lack of fines of the natural ground with rock powders.

Jan 1, 2005

Planning for a surface coal mine includes selecting the best means and equipment for uncovering the coal, loading it, and transporting it to the preparation plant. The machines and methods that will ensure optimum production will depend upon the location and characteristics of the seam to be mined. Stripping Techniques The choice of stripping units is influenced primarily by the system of mining, such as contour or out-crop mining as contrasted to mining in a region of rolling terrain with relatively flat upland surfaces. Factors such as the life of the mining operations production requirements, types of overburden, local and regional dip of coal, and land reclamation are other important considerations.

Jan 10, 1967

By Takashi Sasaoka

Indonesia is the second largest coal exporter to Japan, accounting for about 30 M tons annually. They produced about 150 M tons in 2005, over 99% of which being from open-cut mines [1]. However, the conditions of surface mining are becoming worse each year: the stripping ratio is increasing, approaching the economic ratio and the infrastructure for coal transportation from inland mining areas is insufficient for such intense mining operations. To meet the demand for coal in Indonesia and the rest of the world, underground mines have to be developed. At present, there are only five small underground mines, three of which are old and the other two have only recently begun mining operations [2]. However, severe ground control problems have been occurring regularly, roof falls in particular. At a new mine developed from the highwall, a large bolted roof fall occurred at the heading face, killing two miners. Unfortunately, mining engineers and/or miners in this mine do not have a lot of experiences, expertise and know-how concerning the operations of underground coal mines. Since 2001, Japan has started a ?five-year plan for coal technology transfer? to fill Japan?s moral obligation as the largest coal importer in the world. The research team for this accident was organized and the on-site investigation was conducted in order to find the cause of this accident and make the solution. This paper describes the roof fall accident at the mine, discusses its causes and mechanism and suggests the introduction of some techniques for improving the current support system considering the strata and stress conditions by means of field observation and finite element modeling.

Jan 1, 2007

By L. Lacerda

Spray-on ground support membranes (GSM) or thin support liners hold today perhaps as much potential to impact underground (u/g) ground support operations as dry and later wet-mix shotcrete when introduced to mining in the latter part of the 20th century. This emerging technology has come a long way from the time the first single component experimental coatings were tested in the mid-1980s. Due to a number of factors, including occupational health risk and mine safety regulations, it has taken quite some time for the development of non-hazardous membrane products. However, at this junction most existing u/g mines that employ more conventional forms of ground support could benefit from evaluating GSM technology as a means of improving safety and the bottom line. The same is especially true for future mine developments. This paper describes Master Builders Inc.’s CS1251 GSM product and its implementation. It discusses the situations in which GSM may replace other forms of ground support. Furthermore, it evaluates GSM costs & safety issues and looks at present applications and the potentially bright future of this technology.

Jan 1, 2002

This paper presents a rationale for selecting appropriate support elements which combine to form a support system to maintain stability in mines subjected to both strainburst and the shaking that occurs from fault slip. The overall approach was developed during the 'case for safety' study undertaken to allow the then Beaconsfield Gold mine (now Tasmania mine) to resume development and production after the 25 April 2006 ground-fall and fatality that received worldwide publicity. Issues of the sometimes competing requirements of support element performance during dynamic loading are discussed and the need for support flexibility is contrasted with the usual high support element stiffness required when these are used to reinforce rock masses. An example is presented to show the steps and technical details required to design each component of a support system to counter the de-stabilising effects of seismicity.

Nov 25, 2010

On April 1, 1982, the Bureau of Mines and the Department of Energy entered into an Interagency Agreement to develop an enhanced computer cost model for uranium in situ leach mining. The original computer cost model contained data base information related to two regions; the Wyoming basin region and the South Texas trend area. The enhanced cost model contains additional information on San Juan Basin type deposits. This addition is significant because it expands the model's capabilites to include one of the largest uranium producing areas in the United States and developes costs related to uranium production from in situ leach mining. The data base was expanded and modified to include changes necessary for San Juan basin type deposits. These changes included, but were not limited to, state and local taxes, royalty payments, depth of deposits, drilling costs, and electrical costs. Also site visits were taken to verify many of the base case parameters. Consequently, the data base has been incorporated into the computer program and existing software was modified to provide for the additional data. Information was obtained on drilling coats and therefore the current program more accurately reflects these costs to depths of 2500 feet. This depth parameter has been expanded to include Wyoming Basin and South Texas scenarios also. Verbal communications were held with one operator in the Crownpoint, New Mexico area as well as the state regulatory agencies to help validate the expanded model. As a result of these changes, several tables have been included, summarizing changes in the new default parameters and the overall range of input parameters.

Jan 1, 1982

By Tumilty JA, Schmidt CG

Sulphide ion is a powerful poison in gold cyanidation, however, the detrimental effect is less severe in plant practice. This is thought to be due to the presence of depassivating elements in the ore, mainly lead. Trace amounts of lead can counteract the poisonous effect of considerable amounts of sulphide. The reaction is instantaneous and is likely to be a direct involvement in the electrochemical surface reaction. Lead addition cannot be regarded as an all-round cure when experiencing poor leach efficiencies. A possible beneficial effect depends on the mineralogy of the ore and has to be determined individually for every material.

Jan 1, 1989

Please note all Proceedings of the Institute were taken verbatim by stenotypists from Hyatt & Associates of Denver and editing has been minimal. MR. MORTENSEN: On behalf of the Rocky Mountain Coal Mining Institute, I take great plea¬sure in saying good morning to you at Vail. With a few clouds in the sky, at least we won't get sunburned. We won't have to worry about our kids in the swimming pool, perhaps. It is delightful for me to have been able to have represented the Rocky Mountain Coal Mining Institute for the year 1982-1983. This has been our 71st year and this is our 79th meeting. In recognizing the attendance here, that dinner we had last night, and some of our entertainment must have gotten to some of us, or it is a little early. But I'm sure as the day goes on, and with the speakers outlined, it will be very beneficial for those who do attend. We do appreciate your attendance. I'd first like to make an introduction of our head table. Doris Finnie, she is our executive secretary. As most of you are aware, Gussie Whiteside retired as secretary. This will be the first time since the Institute started that there has not been a Whiteside present at one of our conventions. I'm sure Gussie would appreciate any calls or letters that any of you would care to make to her. Doris, I might add, has been a great help to me and all of the people who have been working on the program for the Institute this past year. There's been lots of reorganization and we are very pleased with Doris's ability to take hold from Gussie without any waves. Much credit must be given to you Doris for this and we do appreciate the help you have given us and believe me she has kept us out of trouble. Next, we have Art Neill. He is our vice president of the Institute from Montana and he also works with Western Energy Company. We appreciate the help that all of these session leaders and chairmen give to us. We have other names on the head table, but they will fill in as the morning goes on, so we won't bother you with any of those at this time. To set the stage for business, first I would like to call on Doris for a motion to approve the minutes of last year. MS. FINNIE: Thank you, Vernal. Mr. President, I suggest that the reading of the minutes be dispensed with and that the members refer to pages 9 through 80 of the Proceedings for the 78th regular meeting of RMCMI, as published MR. MORTENSEN: Thank you, Doris. Do we have a motion to so approve? MR. LINVILLE: I so move. MR. MORTENSEN: Loren Linville so approved. Do we have a second? MR. GARR: Second. MR. MORTENSEN: All in favor say aye. (Audience responded affirmatively.) MR. MORTENSEN: Those opposed? Hearing none, the motion is carried. I'm sure glad we didn't have to read those 80 pages. Is Doug Hammer in the audience? He was going to give us a list of new members of the Coal Institute and ask for your approval. But because of his absence, the names will be listed so that you can read them at a later date, I will entertain a motion that we approve the new members who have joined the Institute. Do I so have a motion? MR. BERNSTROM: I would make that motion. MR. GARR: I second. MR. MORTENSEN: Do we have any questions? All in favor¬ (Audience responded affirmatively.) MR. MORTENSEN: Any opposed? Hearing none, the motion is carried. Next, we'd like to proceeed with our Nominating committee report from the chairman, George Nugent, and the election of next year's officers. George, would you please take the stand? MR. NUGENT: Mr. President, and members of the Institute, your Nominating committee consists of five past presidents of the Rocky Mountain Coal Mining Institute. From Colorado Roy Coulson; from New Mexico, Bob Wilson; from Utah, Bob

Jan 1, 1983