Search Documents

To develop and design a bit that will rapidly drill smooth and precise instrumentation holes in soft rock. Approach Use a one-piece bit made by combining a drag bit and a diamond bit. Because a smooth-walled borehole with a precise diameter is needed for borehole pressure cells (BPC) and other borehole instruments, a diamond bit is usually used. However, diamond bit drilling is slow, and the bit will tend to bind when squeezing ground is encountered. On the other hand, the drag bit will cut faster, but the walls of the drill hole will be rough and the diameter will not be as precise. The combination will provide a bit which penetrates as rapidly as a drag bit, but retains the smooth-wall and precise borehole diameter of a diamond bit. How It Works A three-foot-length of EW-size drill rod is centered in a diamond bit by welding it to three equally-positioned spacers at each end of the bit. A drag bit is attached to the EW rod with a standard EW-to-drag bit adapter as shown in the diagram. Three equally-spaced diamond inserts are set to the desired hole size and welded to the diamond bit barrel behind the crown. These inserts increase the smoothness and precision of the hole by cut-ting away any hole closure. Three equally-spaced shims are set approximately 0.020-inch under the overall insert diameter size and welded to the rear of the diamond bit barrel. The combination bit should be used on a diamond drill with either water, mist or air as the coolant.

Jan 1, 1982

Historic mining across the Bendigo goldfield reached an average mining depth of 750 m over an area of about 16 km by 4 km, with two shafts exceeding 1400 m. Mining ceased in the mid 1900s due in part to increased dewatering and ventilation demands. Water extraction technology of the day, combined with multiple mine ownership, did not allow uninterrupted and thus economic mining activity to prosper. Today Bendigo Mining Limited (BML) is targeting gold-bearing reefs beneath the water-filled historic mine workings. To ensure mining activity can proceed without the risk of water inrush, historic workings are being dewatered by submersible pumps in historic shafts and through a series of underground drain holes intersecting old workings. Due to the high heads involved, individual drain hole development requires rigorous safety control implementation and assessment prior to drilling. Water extracted via drain holes is pumped to the surface through a series of pipe lines and rising mains in conjunction with two staged pumping stations. Both stations are equipped with high-speed centrifugal pumps, each capable of pumping 40 L/s at a static head of approximately 300 m. BML, which operates beneath and within a large city, is confronted with unusual environmental and social challenges compared to many within the mining industry. The raw mine water, which contains elevated salt levels, is piped through residential areas and must comply with strict controls to prevent impacts on the surrounding environment. The final delivery point is BMLÆs water treatment plant at the north end of the city. The water treatment plant utilises chemical pretreatment and reverse osmosis. It is able to process 7 ML of mine water per day at full production. The product is approximately 5 ML of reusable irrigation quality water, which is made available to the Bendigo community for public gardens, sporting facilities and rural irrigation. The 2 ML of brine is directed to a purpose-built evaporation pond facility located 7 km north of the water treatment facility.

Jan 1, 2008

By K. N. Han, X. Xie

The dissolution behavior of palladium powder in thiourea solutions was investigated. The variables studied were temperature, stirring speed and the concentrations of thiourea, acid and ferric ion. Palladium was found to be soluble in thiourea solutions in the presence of an oxidant such as ferric ion. The dissolution of palladium in thiourea solutions was believed to be chemical-reaction controlled, with an apparent activation energy of about 25.3 kJ/mol.

Jan 1, 1997

By Kevin Malone

Mercury, or quicksilver as it is often called, has many applications in modern technology. Used principally in electrical apparatus, industrial contol instruments, insecticides and fungicides, electrolytic preparation of chlorine and caustic soda, chemical processes, pharmaceuticals, and dental preparations, the liquid metal has unusual properties that make it a preferred material for many industrial uses. United States consumption of mercury during the past 40 years shows a rising trend. In all except 4 years, U.S. production has been less than the domestic requirement, and imports, principally from Spain, Italy, and Mexico, have supplied most of the deficit. After World War II, domestic output decreased rapidly until 1950, when it was the lowest in the 100 years covered by production records. Higher mercury prices since 1950 have reversed the decline in domestic output and reduced the gap between U.S. production and consumption. Domestic output in 1958 was the highest in peacetime since 1883; however, the nation still imported 28 percent of its mercury requirements from 1950 to 1960 the price of mercury was high as a result of industrial applications of the mercury cell, the impact of the cold war and the Korean war, and the Government stockpiling program. The stockpiling program, in effect, put a floor under mercury prices even though only 9,428 flasks of domestic mercury went into the stockpile under the original program which ran from July 1954 to December 31, 1957. Under an extension of the program, an additional 17,463 flasks was purchased.

Jan 1, 1962

By William J. Kohan

Milling has traditionally been considered more art than science. In the last 10 years, significant improvements in process equipment have been made and we are finally taking significant steps toward approaching grinding as a science. Two machines have been at the center of this development. These are the roll press and the high efficiency separator. The former can be considered as a new technology or adaptation of existing i.e. roller mill. The latter is clearly an improvement of existing technology. Other machines have been introduced to a lesser degree and later. Among these are the CKP and Horomill. The purpose of this paper is to provide an over- view of the currently available modifications for operating systems and options for new milling circuits with some comments on their application and history.

Jan 1, 1997

By M. Soleimanifar

With more and more industrial construction projects implementing RFID and other sensor-based technologies on fabrication and project sites, new innovative processes are needed to help automatically read and re-position RFID tags while reducing the cost to deploy RFID infrastructure over large areas. RFID tags are being used on construction sites to help identify the location of materials, equipment and personnel to aid in finding project critical materials and equipment required to construct the industrial facility on time and on budget. This research provides a cost-effective process for reading tens of thousands of RFID tags over large project sites from outdoor laydown yards, to warehouses to the workface where the materials and tagged equipment are installed. Based on the collected RFID and sensor data, localization mechanisms determine the most recent coordinates of the tagged components. The paper will cover analysis of RFID collected data and key lessons learned from a commercial deployment of the SiteSense® system with one Alberta-based industrial contractor, JV Driver Fabricators, at an 80-Acre module, pipe spool and structural steel fabrication site.

Aug 1, 2013

By General Meigs

I do not know that I can do any more than to express my entire concurrence in the views which have. been already expressed by Mr. Macdonald. It appears to me that he has we over the wholz subject. I might add in regard to appealing to the Govern-

Jan 1, 1882

By G. W. Brock

Experiments in the form of aging of overstrained tension specimens and elevated temperature tension testing, have been carried out on recrystallized arc-cast molybdenum. The aging behavior of molybdenum was found to be strongly dependent on the degree of plastic strain present in the lattice: the reason for this being the low solid solubility for the common interstitial elements in molybdenum. GEORGE W. BROCK, formerly Research Associate, Department of Theoretical and Applied Mechanics, University of Illinois, Urbana, III., is Research Associate, Department of Engineering Sciences, IBM Research Center, Yorktown Heights, N. Y. Manuscript submitted January 19, 1961. IMD THE term strain aging is familiar in connection with the recovery of the yield point in mild steel after tensile overstraining, and there are other instances where it is known to exert an appreciable effect on mechanical properties. For example, steel exhibits a greater tensile strength at mildly elevated temperatures than at room temperature and serrated stress-strain flow curves occur under certain conditions. It has been known for a number of years that the phenomenon of strain aging is directly connected with the presence of carbon and nitrogen in the lattice; and extremely small amounts of either element are sufficient to produce the effect. In this study, the aging behavior of overstrained tensile specimens of recrystallized molybdenum has

Jan 1, 1962

By Wallace W. Roepke

Four bit designs, two conical and two radial, were tested in coal against a 60° conical reference bit to obtain data on orthogonal cutting forces and primary respirable dust generation. One conical and one radial design were modified by the Bureau of Mines for these tests. Results were mixed: One radial bit used substantially lower overall cutting forces and specific energy than the other bits and was the only cutter lower on energy and most forces than the standard 60° bit. How-ever, it generated more specific and total dust than any other bit. The four bits were also tested for incendivity, with a 90° plumb-bob bit as the reference. The frictional ignition tests were designed to simulate both trimming top rock and cutting such rock during advance on-sump. Results of these tests were also mixed. The radial bits were substantially less incendive than the reference bit and caused no ignitions in either top trimming or sump modes. Only the modified mushroom-tipped conical bit caused ignitions. Bits similar to this modified design should not be used on drum-type miners in gassy mine areas; in-stead, the other types of bits tested should be used to reduce ignition potential to a minimum.

Jan 1, 1983

By Larry R. Fletcher, Virgil J. Stachural, Matthew N. Plis

The Bureau of Mines is conducting research on blasting methods that reduce highwall overbreak and the associated rockfall hazards. This paper presents the results of a series of tests to improve presplitting at a western surface coal mine. Reductions in overbreak were achieved by decoupling and/or repositioning the main explosive charge in the 10-5/8 inch presplit blastholes that formed the highwall. Blast designs are presented by the authors for 1) repositioning the explosive charge from a weak rock layer to a stronger rock layer, 2) decoupling with cardboard tubes in the toe region, and 3) suspending bagged powder at intervals along the length of the blasthole. About the same total quantity of explosives was used in all three test designs. It was readily apparent from periodic visual examination and photographic surveys of the highwalls that the amount of rockfall was reduced, and with a longer delay before rockfalls began, in all test areas.

Jan 1, 1991

By John Mathews

DURING the prosecution of the aircraft-production program in 1917 and 1918, the writer visited many plants engaged in the manufacture of motors, planes and parts, in carrying out his duties as chairman of the Committee on Aircraft-engine Forgings. On several occasions, when the question of expansion was discussed, it was noted that there was confusion in the use of the terms: the true coefficient of expansion, a physical constant, and distortion in hardening. One engineer, referring to a steel shown in the accompanying table; stated that he could not consider it for crankshafts because of its excessive coefficient of expansion, while another steel, also listed in the table, as said to be especially good because it had no coefficient of expansion, since it came out of the oil bath perfectly straight. Many years ago one of our employees designed anew oil furnace; when asked what became of the products of combustion, he replied: "There ain't any, we burn them all up." While the coefficient of expansion is not without its effect in volume changes in hardened steel, it is not a determining factor in the matter of distortion and going out of shape. Irregular heating, uneven furnace bottoms, and carelessness in withdrawing the part from the furnace, as well as the manner in which the part enters the quenching bath are of greater moment. Generally speaking, also, steels of relatively low hardening temperature will distort less than those requiring higher hardening heats. The coefficient of expansion must be considered in engineering design most frequently when different metals or alloys are used in the same construction. For example, the difference of expansion between a steel crankshaft and an aluminum crank-case might be of real importance and a steel with no coefficient of expansion would be much less desirable than one with the normal coefficient. About 15 years ago, the writer made many determinations of the coefficient of expansion at low temperature ranges, usually between 20° and 100° C. Among the materials tested were: Pure forged electrolytic iron, 11.73 parts per million for 1° C.; cast aluminum (99.93 per cent. Al.),

Jan 2, 1920

By Hamid Maleki

A new failure criteria is proposed for assessment of roof stability in underground sedimentary rocks. Unlike other stability assessment techniques, this method is simple and practical, having improved mine safety and productivity in several mines. It is shown that roof movements accelerate to a critical rate prior to actual roof collapse. Critical rates vary between 0.025 inches per day to 0.2 inches per minute depending on rock mass - pillar mechanical properties. Specific critical rates are determined for three rock mass - pillar categories which are common to mining in sedimentary rocks. Time-to-caving varies from one minute to ten days on rock structural controls and type of primary support utilized.

Jan 1, 1990

By W. K. C. Boemer, G. A. Davies

Vanadium slag production in the shaking ladles started in April 1968, steelmaking was begun in July 1968 and the first continuously cast blocks were produced soon after on the 29th July, 1968. Nominal monthly production of over 20 000 tons was reached in seven months and by December 1970 about 12 000 heats were cast and a monthly production of 35000 tons has been achieved.

By Simon D. Strauss

COPPER In terms of mining activity, copper is the leading nonferrous metal. It is true that in recent years the volume of aluminum consumption in the non-Communist world has exceeded the volume of copper consumption, but virtually the entire primary aluminum supply is derived from bauxite. On the average, only four tons of bauxite need be mined to produce a ton of aluminum. By contrast, the highest-grade, large-scale copper mines now in operation (those in the Congo) must mine at least 20 tons of ore to produce a ton of copper. In the United States an average of 150 tons of ore must be mined to produce a ton of copper. This does not take into account the huge amounts of waste overburden that must be stripped from the open-pit mines to account for their steadily rising share of the world's copper output. Copper epitomizes the economic problems of the mining industry in many ways. Its price is highly volatile, considering its great economic importance. It has been a tool of mankind longer than any other of the base metals-the dawn of history has been classified as "The Bronze Age." World Copper Production Although copper is mined in many countries, in recent years 70% of the non-Communist world production has come from six countries. Two of these are industrialized countries and are large consumers-United States and Canada. The other four are developing countries with very small domestic requirements-Chile, Zambia, Zaire, and Peru. Heavily dependent on copper exports to sustain their domestic economies, these countries find themselves oscillating between prosperity and depression with the changing levels of copper prices. In an effort to control their own destiny, in 1968 they formed an organization of copper exporting countries (CIPEC) which was designed to study copper markets and possibly to intervene actively in these markets. (When this chapter was being prepared, no actual steps along such lines had been taken.) Many of the leading industrialized nations are wholly dependent on imports for their primary copper supplies. These include West Germany, the United Kingdom, France, Italy, and many others. Japan, now the non-Communist world's second largest copper consumer, produces only 10 to 15% of its requirements from domestic mines. Although the bulk of the copper output is smelted in the country where it is mined, there is a limited international trade in copper concentrates. Canada, the Philippines, Australia, and Papua-New Guinea are significant exporters of copper concentrates; Japan, Germany, the United States, and Sweden are importers. However, this trade accounted for only about 10% of the non-Communist world production of copper during the decade of the 1960s.

Jan 1, 1976

By Robert W. Zimmerman

POROUS SOLID COMPRESSIBILITIES There are four different compressibilities associated with porous solids, each relating the fractional change in either bulk volume or pore volume with the change in either pore pressure or confining pressure. These will be referred to as Cbc, Cbp, Cpc, and Cpp, with the first subscript denoting the relevant volume, and the second subscript denoting the relevant pressure. They are defined as: [ ] Note that minus signs are included in two of the definitions so that each of the compressibilities will always have a positive value. In general, each compressibility depends on the elastic moduli of the matrix material, the porosity, and the exact geometry of the pores. Taking the latter factor into account calls for separate analysis for each different pore shape, which of course can only be attempted for a few relatively simple cases. But lower bounds for each of the four compressibilities can be found, independant of pore structure, in terms of only the porosity (0) and the elastic moduli of the matrix material (any pair chosen from K, E, G and V). The first step is to find relationships between the four compressibilities, starting with the following observation: If a porous solid made of a linear elastic, isotropic and homogeneous matrix material is subjected to uniform hydrostatic pressure of magnitude P on its external and all of its internal (pore) surfaces, the state of stress in the solid will be exactly the same as that which would occur

Jan 1, 1982

By Josh Swank

Albert Einstein once said, ?the important thing is not to stop questioning.? In the mining industry, a lack of inquisitiveness may lead to a blissful ignorance but it certainly will not increase efficiencies. While one may claim necessity is the mother of invention, questioning and analyzing how methods and systems can be improved is the catalyst to discovering necessities. Understandably, when working in the middle of Canada?s oil sands, where trucks operate around the clock every day of the year, it is nearly impossible to pull the nose from the grindstone long enough to provide thorough analysis. But, fortunately, some manufacturers/inventors have assisted by examining the process and the ensuing headaches within this application.

Jan 1, 2013

By R. Blickensderfer

The sparking and gas-igniting tendency of steels and alloys were evaluated my measuring the radiance of spark showers produced by grinding a sample on an abrasive wheel in air, the time required for a spark shower generated on an abrasive wheel to produce an ignition in an explosive gas mixture, and the energy and speed required for impacts between various materials to ignite an explosive gas mixture. Mixtures of air-methane were found quite resistant to ignition by showers of sparks. A mixture of air-9.S pct hydrogen was used to increase the sensitivity of the tests and to thereby extend the range of materials that could be evaluated. The results of the spark-shower tests indicate that carbon steels and the alloy steels found in coal-cutter tools are among the most sparking and most incendive of any materials tested. Stainless steels, nickel alloys, and tungsten carbide are among the least sparking and least incendive. The brightness of the spark showers depended upon the degree of oxidation of the abraded particles. Impact tests against hard rocks such as solid quartz and sandstone, showed that high-carbon steel was more inc endive in the hydrogen mixture than were the softer steels or the alloy steels found in coal cutters. Ignitions were found much less likely to occur at speeds somewhat lower than the speeds currently in use in continuous mining machines.

Jan 1, 1972

By C. Hays, R. E. Swift, E. G. Kendall

Investigations of the Zr-Pt system, by metallography, incipient melting, and X-ray diffraction, determined the phase relationshifis from 0 to 50 at. pct Pt. Phase fields in the Pt-~ich region were outlined, and three intermetallics (ZrPt, Zr2Pt, and ZrPtd were located. A eutectic between Zr and Zr2Pt, and a eutectoid veaction between Zr and a Zr + Zr2Pt, were established. The maximum solubility of Pt in P Zr was approximately 13.5 wt pct, as opposed to less than 1 wt pct solubility in a Zr. EARLIER work on the Zr-Pt system was limited to an X-ray study on the intermetallic compound, ZrPt3, by H. J. Wallbaum,1 It was reported that ZrPt3 existed at 86.52 wt pct Pt, and had a hexagonal structure, isomorphous with TiNi3. Wallbaum's data revealed the following structural particulars: a = 5.633A, c = 9.21A, and c/a = 1.635A. Other studies allied to Zr-Pt alloys concerned only 1) Pt-rich alloys (0.05 to 5.0 pct Zr) for corrosion resistance,2 2) a Zr-base alloy with 5 pct Pt and 0.124 pct C for oxidation resistance,3 and 3) electroclad-ding of Zr with Pt for in-pile corrosion resistance of Zr to uranyl sulphate. 4 Metallographic, incipient melting, and X-ray diffraction techniques were applied to accurately resolve the phase relationships in the 0 to 50 at. pct (68.2 wt pct) Pt region, and to outline the phase fields in the Pt-rich area. Three intermediate phases: Zr2Pt, ZrPt, and ZrPt3, were also established by the same methods. PROCEDURE Melting stock for this program was of the highest purity obtainable. The Zr was iodide crystal bar with a low hafnium content of about 0.05 wt pct (Westinghouse "Grade 3"). The as-received Zr was treated to remove the surface film of corrosion product that resulted from a standard autoclave grade designation test. Next, the bars were processed to yield material suitable for arc melting and free of contaminants. Sheet platinum metal (Baker and Co. "Grade 2") was used for alloying additions. This material con-

Jan 1, 1962

By A. A. Tytko, T. S. Golosinski

"The paper discusses the accuracy of magnetic inspections of corroded hoist ropes. It quantifies the error of measured LMA (loss of metallic area) caused by presence in the rope of ferromagnetic products of corrosion. The paper concludes that in mining practice this error is not significant. Hoist Rope Corrosion and its AssessmentCorrosion is one of the most common forms of wire rope wear. For ropes working in wet mine shafts, ropes used by the fishing industry and, in general, ropes working in humid and chemically active environments, corrosion wear is usually the prime reason for rope discard. In most mining applications, rope corrosion is accompanied by fatigue cracking of wires, abrasion of external wires, internal nicking and other forms of wear.Quantification of corrosion damage in ropes using standard inspection procedures and examination methods is very difficult. Qualitative comparisons are sometimes used to describe the degree of rope corrosion to compensate for the lack of quantitative measures (SABS 0293, 1996). If available, the results of magnetic examinations of ropes may be of help in assessing their corrosion weakening.Magnetic rope examination requires that the rope first be magnetized. After that, the rope magnetic flux and the leakage flux along the rope are measured. The first is assumed to be directly proportional to rope metallic area (LMA) and its changes are indicative of the rope’s loss of breaking strength (LBS). Existence of the second indicates existence of local faults (LF) in the inspected rope. As the corrosion of rope results in development of corrosion cracks and in loss of rope metallic area, both the LF and the LMA should be used to quantify the level of rope corrosion. More specifically, the changes to the amplitude of the LF signal are considered to provide qualitative information on rope corrosion (Hansel et al., 1990), while those of the LMA signal are believed to provide quantitative information (Geller and Rousseau, 1990; Golosinski, 1996)."

Jan 1, 1999

By Ana E. Bohé, Fabiola J. Alvarez

"The separation of nickel from the aluminum present in spent catalysts and different metallic industrial residues, is proposed in the following systems: alloy Al2Ni and the mixtures 50 wt% Ni + 50 wt% Al, 10 wt% Ni + 90 wt% Al2O3 and 12 wt% NiO + 88 wt% Al2O3. The experiments were carried out in a tubular reactor with a flow of 2 l/h of gaseous chlorine and from 200 ° to 800 °C. The final products of the reaction, extracted from the hottest zones of the reactor where characterized by XRD, SEM, EDS, AA and XRF, as NiCl2 y NiCl2.6H2O while in the coldest regions AlCl3 was deposited in the first two cases and in the other there was a residue of ?, a- Al2O3, sometimes mixed with some remainder of Ni and NiO. The procedure attained different separation factors which showed the optimun conditions for the recovery of both metals. Introduction Some studies of nickel corrosion were carried out in chlorine gas at temperatures above 950ºC, and suggested that nickel is not corroded below 538ºC. [1] However, in a previous work it was shown that the chlorination allows the separation of nickel from aluminum and the formation of NiCl2 was detected from 200ºC in binary mixtures Ni-Al 50 wt%, for isothermal conditions in chlorine flux. [2] Other researchers obtained selective chlorination above 650ºC of a fly ash containing 1.4 wt% of Ni and other metals (V, Mg, Al and Fe). The Ni was separated from the Mg and NiCl2 started to vaporize at 550ºC and was after condensed in a zone of the reactor above 380ºC with 90% of purity. [3]"

Jan 1, 2008