Search Documents

By D. D. Todd, W. A. Oates

THERMODYNAMIC data for solutions are best derived from a combination of equilibrium and calorimetric studies. However, the accurate measurement of heats of mixing of metallic solutions at high temperatures presents considerable experimental difficulties, simple calorimeters1-3 giving

Jan 1, 1964

By N. Hanief

This research involves the investigation of phase transformations in the platinum-chromium coated system. Single-layer 0.1 µm platinum coatings were deposited via electron beam deposition on 99.98 percent pure chromium substrates. Specimens were subjected to systematic heat treatment in a vacuum furnace at 900°C for up to 20 hours. Phase formation and the changes in surface morphology were investigated by X-ray diffraction (XRD) and scanning electron microscopy (SEM).Both CrPt and Cr3Pt phases are formed during heat treatment for different times at 900°C. Significant changes in the morphology of this coated system were detected after heat treatment at 900°C for 20 hours.

Jan 1, 2012

By R. O. Williams

It is shown that Ni3Al precipitates homogeneously from nickel-rich alwminum alloys as plates on the (100) planes. Prior to actual precipitation a process occurs which is believed to be one of increasing short-range order. After precipitating the Ni3Al plates enlarge through competitive growth. Discontinuous precipitation can occur simultaneously with the above processes. Recent ideas of the origin of precipitation strengthening appear adequate to explain the hardness changes. REMARKABLY little appears to be known about the precipitation process in Ni-Al alloys in spite of their technical importance. This investigation originated to supply additional information about precipitation in general, this system in particular. Information on the structures and kinetics have been obtained through the use of hardness, X-rays, microscopy, calorimetry, and resistivity on high-purity alloys. PROCEDURES Six alloys, Table I, were prepared by melting carbonyl nickel and high-purity aluminum in alumina crucibles in vacuum and casting into 1-in. graphite molds. All rods were homogenized at least once at 1300°C for 24 hr prior to swaging and this was repeated on the first three alloys after 75 pct reduction. Alloy 4 could be reduced only 10 pct at 1000°C (probably in two-phase field) prior to fracture but 1/4-in. samples quenched from 1100°C were readily reduced cold. Alloy 5 was reduced 15 pct cold but failed on the next pass while alloy 6 of essentially the same aluminum content failed inter-granularly without apparent flow up to 1000°C. The alloys were heated in hydrogen at the elevated temperatures and formed thin, coherent aluminum oxide coatings which provided excellent oxidation resistance at lower temperatures. However, freshly prepared surfaces showed considerably less resistance at 500"to 700°C in air and apparently resulted in internal oxidation. As a consequence, low-temperature agings were carried out in evacuated tubes. RESULTS The isothermal hardening behavior of these alloys at 500"and 565C is given in Figs. 1 and 2. These results were obtained from samples cold worked 75 pct, recrystallized at 1000°C (1100°C for the 7.8 pct Al) and quenched in water. This recrystallization was used to give smaller grain sizes so as to obtain more uniform hardness values and the points represent an average of five readings. The electrical resistivity was measured on 1/16-in. wires quenched from 1000°C during aging at 495°C to give Fig. 3. The energy release and its rate are given in Fig. 4 for the 6.9 pct Al alloy during aging around 500°C. Inasmuch as this was a single run, its accuracy is not known but certainly the general shape and magnitudes are correct. The method used to obtain these results is described elsewhere.' Data for the aging at 600°, 700°, and 800°C of these alloys cold worked 50 pct are given in Fig. 5. Supplementary information from microscopy and X-ray diffraction have been included to indicate recrystallization, discontinuous precipitation and the appearance of superlattice lines from the Ni3Al. The hardness of these alloys as annealed, aged, cold worked, and cold worked and aged is given vs composition in Fig. 6. Those samples which were isothermally aged, Figs. 1 and 2, were reaged at 532°C and at successively higher temperatures for the indicated times to give the data of Fig. 7. These results as well as certain others, support the idea that the level of hardness reached for temperatures above 600°C are equilibrium values more or less independent of path. This being the case, the breaks in the curves would be the complete solution of the Ni,Al. The electrical resistivity versus temperatures for some of these alloys, both aged and unaged, is given in Fig. 8 along with those data from heating slowly (10 deg per day) to high temperatures. Interesting points include the lowering of the Curie temperature (the change in slope), the lack of any indications of a solubility limit and the large temperature coefficient for the Ni3Al. A slight break for Ni3Al around 100C shows up but this is not a Curie temperature as Ni3Al is not ferromagnetic down to -190°C. Metallographically both the nickel-rich solid solution and the Ni3Al appear very much like pure nickel. Profuse twin boundaries are present both

Jan 1, 1960

By P. Rosario

The application of high pressure grinding rolls (HPGR) has been growing in the mining industry for the last 10 to 15 years. The major benefits supporting this trend are better energy efficiency, improved grinding capacity, and higher metal recovery in downstream processes such as heap leaching and flotation. In general there is limited quantitative knowledge on the true benefits of HPGRs relative to SAG mills in comminution, and about which situations one deals with better than the other. This paper will present a structure for comparison of the energy requirements for HPGR versus SAG mill considering complete circuits for comminution of precious and base metals hard ores. The work presented is from the design of four complete circuits based on ore data from two sites.

Jan 1, 2010

By M. A. Vergara, J. A. Botín

"The decline of the “super cycle” has placed an end to a decade of production-focused strategies, with operating cost growing at rates higher than production. Today, the sector is placed on a tough ride and forced to shift focus to cash preservation and efficient cost management. However, most cost management systems in the minerals industry are not conceived as value driving tools but to meet financial accounting and reporting needs. This research draws from a the development of an innovative cost management methodology that applies Activity-Based Bottom-Up cost budgeting and continuous improvement tools to develop a value-driven cost management system for sustainable improvement of operational efficiency and cost reduction. The methodology was successfully tested in the Andina underground mine III Panel sector of Corporation del Cobre (CODELCO), in Chile. INTRODUCTION Cost management is fundamental to profitability of any industrial project. Even more essential in mining, an industry that deals with commodities, which prices are dictated by the market and are beyond the management capacity of the company. The end of the mining “super cycle” and the advent in 2008 of the Global Financial Crisis (GFC), placed an end to a decade of production focused strategies, with operating cost growing at rates higher than production. The sector was placed on a tough ride and forced to shift focus to cash preservation and efficient cost management. Many mining companies have seen themselves into the urgent need of cost management systems capable of achieving sustainable productivity gains and consistent profitability. Cost management is composed of three main processes: estimation, budgeting and control [1]. A number of conventional techniques have been used for cost estimation and budgeting for many years. However, most cost control systems in the minerals industry cannot be referred to as “cost management” since they are conceived to fulfil accounting and reporting needs, rather than to improve operational efficiency [2]. In general, conventional cost budgeting and control systems in mining use a “top-down” methodology, which lacks of necessary details, and fail as a management tool leading to undesirable results [3]."

Jan 1, 2016

By Kerry M. Masson

Perhaps the hottest item on the agendas of most state legislators this year is the state budget. The main question: Where will all the dollars come from to finance health care programs, state jobs, unemployment compensation programs, and on and on? This is especially so since people are out of work, business bankruptcies are up, sales are down, and incoming revenues from some sources have decreased or dried up. A sure bet is that state taxes will be increased in some form or another. The mining industry could face increased income taxes, property taxes, severance taxes, or even a host of new taxes (if the state does not already have them) like a gross receipts tax, investment tax, or tax on revenues made outside state borders. That's bad news for an already depressed industry, even though increased taxes may be the least of the industry's worries in the current economic climate. While reopening existing mines and developing most new mineral projects depends primarily on higher commodity prices, new taxes still could pose long term concerns for mine project development. Just how mineral tax law impacts a project is not easy to figure. It involves a complex set of calculations based on interpretations of numerous federal, state, and local tax laws that change almost annually. At best, projections of tax effects for the life of a mine are educated guesses. At the same time, projections are necessary to evaluate the economic feasibility of a mineral project. At a recent Technology Transfer Seminar, the US Bureau of Mines introduced a computer software program designed to evaluate the feasibility of a mineral project and to determine the tax effects on the project's discounted cash flow rate of return (DCFROR). The program, called MINSIM, began in 1967 as a 200-statement FORTRAN II program for evaluating a hypothetical large-scale open-pit gold mine. This single-commodity oriented program employed discrete simulation techniques and a continuous DCFROR was used to measure the effect of changes in revenues and costs. Over the past 15 years, MINSIM has developed into a program 70 to 100 times larger than the original. Basically, it will analyze costs and parameters specific to an identified deposit, then determine the DCFROR. Or by using a specified DCFROR, it will determine the primary commodity price required to attain that specified rate of return. MINSIM, which is explained in detail in this article, is available from the Division of Minerals Availability, USBM free of charge. Written in FORTRAN IV, it comes on punch cards or magnetic tape and is compatible with most major computer systems. The MINSIM Program The main objective of any freeenterprise mining venture is to make a profit. To determine profitability of a given project, alternate methods of operating and financing must be evaluated. That is the purpose of MINSIM. While there are a number of methods of evaluating the economic profitability of a mining project, MINSIM uses the Discounted Cash Flow Rate of Return (DCFROR) method as its major criterion because DCFROR considers the time value of money and gives the truest measure of profitability. One disadvantage is that the calculations are deposit oriented. In other words, MINSIM analyzes only those costs and parameters specific to the deposit. It cannot be used to evaluate the overall corporate picture. The program is designed to simultaneously handle five different commodities and a leach operation for any type of mining project. For example, analysis of a coal project would include only one commodity-coal at the mine mouth. Analysis of a copper operation might include numerous commodities-from the raw material to the refined product. Input MINSIM considers capital investment-recoverable exploration, acquisition, and development costs; depreciable capital investments such as mine plant and equipment, mill plant and equipment, and infrastructure costs; all general and commodity specific operating costs; and the cost of alternate financing methods. The program has the capacity to incorporate different types of depletion allowances, numerous commodity-dependent severance taxes, variations of property taxes, and many methods for calculating state or provincial taxes. There are even many different ways to calculate federal and national taxes. The capacity to handle tax variations is generated from an internal subroutine in the program called the "open file." The user can reconstruct, customize, or evaluate any kind of tax desired. Outputs Given this kind of capacity for numerous input parameters, MINSIM is capable of the follow¬ing major outputs:

Jan 3, 1983

By Scott L. Ewart, William M. Bryden, Donald E. Wakefield

"Osler, Hoskin & Harcourt develops commentaries from time to time on topics of legal interest. These may deal with new legislation, changes or developments in government policy or recent judicial decisions of importance to its clients. The commentaries are, of necessity, general in nature. Because the law which they deal with is often new and untested, it is hard to arrive at precise statements of the way in which the principle s discussed in a commentary might be applied in specific circumstances. When further guidance is needed , consult a solicitor.The purpose of the Bill is to simplify, modernize and standardize the regulation of mineral exploration and development in Ontario. Many of the changes proposed by the Bill are of an administrative nature and move much of the detail with respect to staking, assessment work, prospecting work, surveys, quarry permits and leases contained in the existing Mining Act to the Regulations contemplated under the Bill.The Bill will undergo revision and be re-introduced and therefore it is not the intention of this present article to detail the specific changes contemplated by the Bill; however , its more significant changes are as follows:1. Provision is made for a lifetime prospector's licence with the elimination of annual renewals;2. Perimeter staking of a block o f claims is permitted to reduce the cost of staking;3. Assessment work requirements are expressed in term s of dollars spent rather than days worked;4. Persons doing exploratory work are required to furnish notice to owners of surface rights of intention to perform assessment work;5. Annual work summaries will be available to the industry to lessen duplication in exploration work;6. The option of continuing assessment work rather than applying for a lease is provided;"

Jan 1, 1984

By H. J. Roorda

With an increasing need to obtain metals by processing complex fine intergrown ores, the use of electron-optical techniques will become more important as a tool for mineralogical studies. Electron images enable a higher spacial resolution than can be obtained by optical microscopy and thus provide a powerful and necessary aid for the examination of small grains and finely locked particles. In this paper the mineralogy of Meggen ore was investigated. Both light-optical and electron-optical techniques were used to evaluate the mill feed and products of the concentrator. Detailed examination by reflected-light microscopy to assess the comportment of galena in the complex pyritic ore was inconclusive in establishing the cause for low lead recovery of only forty percent of the ore's lead content. Electron microprobe analyses indicated that the majority of the lead lost to the tailings was accounted for by extreme fine (often smaller than one micron) and complex intergrowths of galena in pyrite. The remainder was lost as fine free galena grains.

Jan 1, 1987

By Will Mitchell, T. G. Kirkland, C. L. Sollenberger

BENEFICIATION of a Korean scheelite ore has been studied during the past year in the Basic Industries Laboratory at Allis-Chalmers Manufacturing Co. A flowsheet has been recommended including flotation, gravity separation, and a final cleaning by a magnetic separator. The investigation was continued in the field of flotation in order to establish the effect of certain variables on recovery and grade of rougher concentrates. The results of this investigation are recorded here. Mineralogy The scheelite ore was obtained from Korea and was mined from the Sang Dong deposit. This deposit is described as lying in gently dipping metamorphosed sedimentary beds of Cambrian age.' The metamorphism was probably either metasomatic replacement or recrystallization, or both, with subsequent hydrothermal deposition. Igneous bodies in the form of granite porphyry have been found within 7 km of the main shaft and are considered to be a possible source of the mineralizing solutions. The Myobong formation, the host for the Sang Dong deposit, was laid down in middle Cambrian times and consists of series of mudstone, siltstone, shale, and marl, with local stratification of mica schists, hornfels, and tactites. The scheelite is found in quartz bands in the tactites. Although there are six of these bands, only one, the "main bed" averaging 1.75 pct WOs, has been mined to any extent. The ore sample as received in the laboratory was the product of a cone crusher and was all —2 in. The rock appeared to be even textured, medium to fine grained, and gray green in color. No scheelite could be recognized by the unaided eye. However, under ultraviolet light of 2537 A, the scheelite fluoresced and could be distinguished from the gangue. Under the black light, the scheelite showed no definite vein structure but was disseminated throughout the specimen. The raw ore had a specific gravity of 2.96 and weighed about 125 lb per cu ft at —20-mesh Tyler. The —2-in. material was stage crushed through 20-mesh, and samples were cut for mineralogical, chemical, and spectrochemical analyses. Several polished sections were cut from hand specimens. Figs. 1 and 2 show quartz to be the matrix for scheelite. It was reported by Kim2 that the greatest scheelite concentration in the mine is found with a high concentration of quartz and a decrease in the abundance of garnet. Diameters of scheelite particles ranged from 1.2 mm down to less than 50 microns. Spectrochemical analysis showed the ore to be high in aluminum, bismuth, calcium, iron, magnesium, manganese, silicon, tungsten, and with lesser amounts of beryllium, chromium, lithium, sodium, and titanium. Chemical assays showed the —20-

Jan 1, 1952

By Roger Favreau, Patrice Favreau

The article reviews the aspects which contribute to the quality of the results from a blast with explosives, namely a good floor, no large blocks, easy mucking, and explains the mechanisms of the blasting process which decide on the quality of these aspects for a given blast method, and how these mechanisms can be simulated from basic principles. It proposes that good fragmentation size distribution can also be important if the rock is going to a crusher, e. g. for the ore in a mine and for the rock excavated in a quarry.

Jan 1, 2012

By Chen Song

Cobalt basic carbonate particles were precipitated from 1.0mol cobalt nitrate or cobalt sulfate solution with ammonia carbonate. By controlling the zeta-potential of the particles and the ionic strength of the solution, the uniform particles with ellipsoid or rod shapes were obtained. During the precipitation process, the interface tension was diminished to the minimum and therefore the Ostwald ripening and secondary nucleation were both inhibited. The morphology and the size control by zeta-potential seem to be the result of thermodynamics rather than classical crystalline kinetics. The particle sizes were in the range of 0.4-0.6, 0.3-0.4 micrometer. After thermolysis, the spinel-type C0304 particles were produced. The morphologies of C0304 particles were similar to that of their precursors.

Jan 1, 2003

By Paul M. Tyler, Oliver Bowles

The extensive employment of nonmetallic minerals antedates the use of metals, but only within the last two decades has the production of nonmetals begun actually to keep pace with the complicated activities which characterize the so-called Machine Age. The economic changes ushered in by the Industrial Revolution were reflected first in an increased demand for metals and for fuels. In the modern sense, therefore, the nonmetallic mineral industries are new and afford new opportunities for engineer and economist alike. A certain amount of caution is indicated, therefore, before attempting to apply ready-made formulas to the problems of these industries. Economics is not an exact science. In the field of production technology where the number of variables is fairly well known, the principles of economics are readily applicable, but as the student proceeds through the province of marketing into the unexplored regions of psychology and sociology he must distinguish carefully between scientific reasoning and purely metaphysical speculation, even when the latter masquerades as economics. The present paper attempts to prove no preconceived theorems and is designed primarily to stimulate careful thinking on sundry neglected phases of these industries. An attempt is made to differentiate the general problems into single aspects which afford promise of being comprehended separately; also, some fundamental statistical data are presented, but merely to indicate a method of scientific approach applicable to more intensive studies. Definition Before discussing the economics of the nonmetallic mineral industries, it is appropriate to consider what we mean when we say "nonmetallic minerals." This term, inasmuch as it is merely a negative description, is somewhat loose and ambiguous and gives rise to questions in regard to minerals that, like chromite or bauxite, are alternatively classed either as nonmetallic or as metallic minerals (or ores). The chrome ore used to make ferrochrome for steel manufacture is undoubtedly metallic in character; similar material destined for use as a refractory in the same

Jan 1, 1934

The design and construction of a 2.5 million tonne per annum ship unloading system at the PWCS export coal terminal in Newcastle, NSW, has further increased the flexibility and sophistication of Australia's largest coal export facility. The system comprises a new unloading wharf serviced by a self unloading vessel, conveyor stream and multi compartment ground level storage shed. Coal is reclaimed from this shed by the largest portal scraper ever installed under cover. The system also provides additional flexibility by receiving coal from the existing PWCS road receival to improve scheduling. The PWCS can now simultaneously handle 11 coal types and receive from rail, road and sea at almost 15000 tonnes per hour.

Jan 1, 1987

By M. Muskat, R. D. Wyckoff, H. G. Botset

The flow of liquids through porous media is known to follow Darcy's law which states that the velocity of flow is proportional to the pressure gradient. This law is but a statement of the facts obtained from experimental studies and is, therefore, uncontroversial. It should be men-tioned, however, that it applies only when the flow is viscous in nature and that at excessive velocities which tend to produce turbulence, the velocity is proportional to some power of the pressure gradient, the exponent ranging from 1 to 0.5 as the degree of turbulence increases. However., experiments with media having permeabilities corresponding to those of actual producing horizons show conclusively that the actual flow of liquids in a producing horizon must be viscous except perhaps in the immediate vicinity of a well producing at a high rate. Therefore, one is justified in assuming Darcy's law to hold for cases of practical interest, as will be implicitly assumed in this discussion Given this basic law of flow it is possible, theoretically to obtain solutions to any problem of viscous flow of dead liquids1 by the usual methods of potential theory. However, problems of practical interest often present such complex geometrical configurations of sources and sinks (driving sources and output wells) as to make the analytical solutions extremely difficult or even impossible. It is useful, therefore, to note that Darcy's law is precisely equivalent to the law of electrical conduction, so that the pressure distribution in steady state porous flow of liquids is exactly the same as the potential distribution in an electrical conducting medium.2 This analogy permits the use of electrical models wherein the potential distributions may be measured with far greater facility and accuracy than is possible in actual fluid-sand models. Such electrical models were used in determining the pressure distribution about complex arrays of wells, an example of which will be shown later in the discussion of the 5-spot flood. One phase of the porous flow problems which is of considerable practical interest involves the tracing of an advancing fluid front. Thus,

Jan 1, 1933

By W. P. C. Duyvesteyn, B. J. Sabacky

Reprinted with revisions from Extractive metallurgy of copper, nickel and cobalt, volume I: Fundamental aspects. ed. Reddy R.G., Weizenbach R.N. Warrendale, Pennsylvania: The Minerals, Metals and Materials Society, 1993. Development work on the Escondida process, concluding with the successful operation of an integrated leach-SX-EW pilot plant and a pilot flotation plant for the upgrading of leach residues, demonstrated that all major process objectives could be achieved. Extraction of 40% of copper in concentrates containing monovalent copper was achieved with essentially no oxidation of sulphide sulphur. The Cu contents of leach residues from four different types of concentrate were successfully upgraded to the original feed grades, giving a product that has potential as a high-quality concentrate for the smelter market. A compact solvent extraction section effectively recovered the ammonia lixiviant for recycling to leaching and selectively transferred Cu into a conventional acid sulphate electrowinning system. High-quality "six-nines" copper cathode was produced on commercial-scale stainless steel blanks, demonstrating that the process will be able to compete effectively in the premium cathode market

Dec 1, 1995

By Brian Heer, David Young, Randall Essex

The Manapouri Power Station is New Zealand’s largest hydroelectric facility located on the South Island of New Zealand. Constructed in the 1960’s, it includes a 700 MW under-ground power station and a 9.8 km (6.1 mile), 9.2 m (30 ft) diameter tailrace tunnel. The output of the power station is currently limited due to excessive head losses in the tailrace tunnel. To remedy this situation, the Electricity Corporation of New Zealand (ECNZ) retained Woodward-Clyde to design a second tailrace tunnel and appurtenant facilities and prepare Contract Documents for construction. The Project will involve the construction of a 9.8 km(6.1 miles), 10 m (33 ft) diameter, TBM-mined tunnel, hydraulic control structures at the upstream and downstream ends of the tunnel, an underground dewatering shaft and station, and tailrace channel improvements. This paper summarizes the key design and construction issues addressed during the planning and design phases, outlines the risk management provisions incorporated in the Contract, and overviews the Interactive Tender Process (ITP)that was implemented during the pre-tendering and tendering periods.

Jan 1, 1997

By George A. Savanick

An experimental hydraulic jetting device intended to operate in a 16-in-diam borehole was designed, fabricated, and used to cut coal and simulated coal samples. This device consisted of two 0.107-in-diam nozzles that rotated in a plane perpendicuIar to a 50-inch length of high-pressure tubing. Experi¬ments were also conducted with stationary jets issuing from a single 0.142-in-diam nozzle. Numerous experiments were performed using systematic variations of jet parameters coupled with assessments of cutting rates. These Bureau of Mines tests showed that when operated at 4,000 psi pressure and a 40-gpm flow rate (1) the device can fragment coal up to a distance of 8 feet from the nozzle, (2) 4,000-psi jets cut more effectively than lower pressure jets with the same nozzle diameter, (3) stationary jets do not cut as effectively as moving jets, (4) interkerf breaking occurs when the kerf spacing is less than 2 inches, and (5) if the kerfs are spaced <1/2 inch, the jet is deflected and thereby reduces cutting effectiveness.

Jan 1, 1975

By K. J. Sollman

As a class, silicate minerals have likely found the broadest, if not largest volume, use in combination with polymeric binders of all industrial minerals. Among the silicates, calcium metasilicate, wollastonite, enjoys a front runner position in a near universal sense. It is a viable and desirable part of composites ranging from thin films to large moldings; from a common filler/extender for paint for your garage to a reinforcement for the exterior surfaces of a luxury vehicle affordable to very few. This article is focused upon the variations in particle morphology and the surface characteristics which, by way of commercial examples and discussion of active research programs, make this environmentally benign mineral so unique.

Jan 1, 1993

By W. L. Saunders

WHEN work was begun in September, 1910, on the rock excavation for the foundation of the gigantic dam at Valhalla, N. Y., which is to convert Kensico lake into an important storage reservoir of the Catskill Aqueduct system, one of the first steps taken by the contractor, H. S. Kerbaugh, Inc., was the development of a quarry to supply the stone needed in the construction work.The importance of a bountiful supply of suitable rock in an accessible location is apparent when it is considered that nearly a million cubic yards of cyclopean masonry will be contained in the completed structure, not to mention dimension and facing stones, concrete blocks, and mass concrete. The dam structure will be over 1800 ft. long and about 170 ft. above the present river bed. However, for a distance of some 800 ft., it will be carried down to solid ledge rock, which will make the finished structure about 300 ft. in maximum height. It will be about 200 ft. thick at the base and directly beneath the coping it will be 28 ft. thick. This dam will raise the reservoir surface 110 ft. above old Kensico lake. The reservoir capacity will be 29,000,000,000 gal.-equal to New York&apos;s total needs for over two months. The contract price for this work is nearly $8,000,000 and is second only in amount to the cost, over $12,600,000, of the Ashokan Reservoir work. Fig. 1 is a view of the dam site.

Jan 2, 1914

By A. Rahimi

The smelting plant at Sarcheshmeh Copper complex commenced working with two reverbatory furnaces, four pierce smith converters, two anode furnace and one holding furnace having a known capacity of 420 metric tons of anodic copper according to the initial design in 1982 (1361 Iranian calendar). During the period from the commencement date up until now, the smelting plant has undergone changes for improvement and enhanced production by substituting holding furnace with another anode furnace, installing the fifth converter and utilizing oxyfuel burners on the ceiling of the reverberatory furnaces. According to the different operational processes in reverberatory, converter and anode furnaces different types of corrosion mechanisms and degradation can be observed in the refractories of copper smelting furnaces. In the case of reverberatory furnaces, the corrosion and degradation of refractories may be factors such as hot corrosion by melt, corrosion attack by the constituents of burning fuel, degradation of sidewalk exposed to mechanical stresses of the feed charge and the hydrostatic pressure exerted by the melt inside the furnace, all of which are due to the unique operational condition governing the reverberatory furnaces environment, i.e. burning fuel atmosphere, charge concentration and combination, furnace temperature, calm melt condition, etc. In the case of converter furnaces, the most likely corrosion and degradation of refractories may be due to the chemical reaction between the melt and degradation of tuyere zones due to sever movement of the melt and mechanical strikes of the punch rod. Also the most essential corrosion reaction occurs around the mouth of the converter because of the mechanical strikes by the cleaning device and thermal heat shock. Other parts inside the furnace are corroded due to the reactions between the fayalite slag and the furnace refractory. In anode furnaces the degradation mechanism is mostly related to the gaseous corrosion (penetration of natural gas or liquid gas inside the refractory structure due to the long period of reduction processes and refining stages. Finally another important factor responsible for destruction of refractories in these furnaces is the copper oxide slag together with the fume constituents of burning fuels.

Jan 1, 2004