Search Documents

By Gealy W. Wallwork

INTRODUCTION The administrative processes of coal mines are becoming increasingly complex. As society evolves into a more complicated structure with greater emphasis on individuality, government regulations reach deeply into every activity in an effort to force individuals into a standardized mold. These contradictory pressures add an extra burden to the administration of a mining operation. Recent years have brought a substantial change in the skills needed by mine supervisors and managers. As a result, a better understanding of the administrative functions is necessary. The mine superintendent has the overall responsibility for the mine; for effective operation he must be sufficiently knowledgeable to oversee all the complex functions that make up the mine. This chapter does not cover all the administrative requirements because of the variation in mine operation and in company policies and organizational structure. It does attempt to identify the administrative functions that would be required at a large mine with a preparation plant. It is assumed that the mine operation is decentralized with very little duplication of functions at the organizational levels above the mine. Thus each function is assumed to be relatively complete at the mine and under the general supervision of the mine superintendent. EMPLOYMENT PROCEDURES Throughout the mining industry, in deep or surface mining, in union or nonunion companies, the success or failure of an organization is directly related to the caliber of employees who make up the organization. A company is nothing more than a group of people working together with

Jan 1, 1981

By Ian Townsend

A prerequisite for good filter performance is that the total filter installation has been well designed. In this sense, the filtration testwork will provide scale-up data, and an insight into the relationship between operating parameters that may then be optimised, and used in the development of a control strategy. A good understanding of the filter’s operating principles will ensure correct selection and sizing of ancillaries, allowing in particular for the difference between instantaneous and average flow rates.

Sep 13, 2001

By Peter Swanson, Collin Stewart, Wendell Koontz

A seismic monitoring network has recently been installed in the North Fork Valley coal mining region of western Colorado as part of a NIOSH mine safety technology transfer project with two longwall coal mine operators. Data recorded with this network will be used to characterize mining related and natural seismic activity in the vicinity of the mines and examine potential hazards due to ground shaking near critical structures such as impoundment dams, reservoirs, and steep slopes. Ten triaxial strong-motion accelerometers have been installed on the surface to form the core of a network that covers approximately 250 square kilometers (100 sq. miles) of rugged canyon-mesa terrain. Spread-spectrum radio networks are used to telemeter continuous streams of seismic waveform data to a central location where they are converted to IP data streams and ported to the Internet for processing, archiving, and analysis.

By Carle Hayward

AT THE February, 1916, meeting of the Institute, a paper presented by Hayward and Raymond gave the results of a study on the effect of time in tempering medium-carbon steel, when the following conclusions were reached: It is not fair to consider the question settled when only three specimens were used for each treatment, but the results obtained indicate that for reheating quenched medium-carbon steel to temperatures below 500° it is only necessary to heat it through. Longer heating has little or no effect on the tensile strength, ductility, or hardness. At temperatures above 500°, increasing the time of treatment causes a slight falling off in hardness and tensile strength with a corresponding increase in ductility. In the discussion of the paper these conclusions were attacked and evidence presented that seemed to throw doubt on their accuracy. The authors, however, showed that this evidence was based on high-carbon or alloy steels and no facts regarding medium-carbon steel were presented. During this study the heat treatment was carried out in a small electric resistance furnace. It held nine specimens, but when these were placed in the furnace the temperature was lowered to such an extent that 30 to 40 min. were required to reach the desired heat. The authors pointed to this as a weak point in the investigation and it seemed wise to supplement the research by work on similar steel but using a different method of heating. This has been done and the results are given in the present paper. The Rhode Island Tool Co. cooperated by furnishing the steel and turning the tensile specimens.

Jan 1, 1922

By R. J. Cornelius

Gold with minor associated copper mineralization in the area of what is now the Bougainville porphyry copper deposit has been known since the 1920s and was probably known in German colonial times, pre- 19 14, although no records persist other than a reference by Stanley (1922) to copper specimens from Kieta that he saw in Rabaul. Stanley did not at the time believe that they came from Kieta. Gold was first discovered at Kupei by Jack Comb in 1929 and the Kieta Goldfield was proclaimed in May 1930. In December 1932, the Tapu Reward Claim at Moroni - the site of the Bougainville Copper concentrator, was pegged by C.W.M. Evans who prospected up river from the West Coast. The Pumkuna (Panguna) Reward Claim on the site of the subsequent porphyry copper deposit was granted in February 1934 to G.A. Myers. n May 193 1, the Kupei Reward Claim was transferred to Bou- gainville Gold Options NL and later reverted to Jack Comb and then the Bougainville Syndicate, as did the Pumkuna and Moroni claims. Most of the interested parties had come from the Edie Creek rush on the New Guinea mainland. In 1935, N.H. Fisher, the geologist in Rabaul for the New Guinea administration who later became director of the Australian Bureau of Mineral Resources in Canberra, reported on the three gold areas. Norm Fisher described the gold and copper mineralization and its habit in great detail and this report had a major influence on the events leading to the discovery in the 1960s. Gold production up to the Japanese invasion probably did not exceed $50,000 in value. Half a ton of copper-gold ore from Kupei was sent to O.T. Lempriere's in Sydney for assay in the early 1930s.

Jan 1, 1991

By J. Lyndon Rosenblad

The strength of a jointed-rock mass is not well-understood. It is believed, however, that the behavior of a rock mass is governed by both the intact rock properties and the properties of the discontinuities. Rock research in the past has been concentrated on the determination of intact rock properties. Several studies are presently underway which should provide more insight into the properties of the discontinuities. Few research programs, however, have been undertaken with the intent of studying the composite rock mass behavior where either the intact rock strength or the properties of the discontinuities may control failure. There are three approaches available for studying the behavior of a rock mass, namely, field studies, mathematical models (finite element), and geomechanical models. A geomechanical model has been developed in this study where the strength and failure modes of a model rock mass are studied as a function of intact block geometry, joint orientation, joint properties, and confining pressure. The objective of this study is to gain some insight into the parameters that govern the behavior of a rock mass, which parameters are most important, and when these parameters control. This chapter describes only one phase of the study, the development of equipment for use with the rock-blocks model. The models being tested are approximately 22 x 22 x 6-in. The size varies slightly depending upon the joint orientation used. The equipment developed includes model material molds, reaction frames, loading apparatus, measuring and recording instrumentation, and other accessory equipment pertinent to the operation of a successful study. The usual problems in equipment development, such as uniformity of load application, loading capabilities, and reaction capacities are all

Jan 1, 1970

Natural gas is a comparatively new fuel in Australia. It was first used in small quantities in Queensland in 1965, but it was not until 1969 that natural gas reached the capital cities Brisbane, Melbourne, and Adelaide in that order; then in 1971 it reached Perth. By the mid seventies, natural gas had secured a significant proportion of the energy markets in Queensland, Victoria, South Australia and Western Australia and in 1976 supply commenced in Sydney. In that year - 1976 - gas supplied about 12.5% of the total demand for primary energy in Australia excluding transport. In the current financial year - 1981/82 - natural gas is expected to supply nearly 19% of the market and forecasts for 1990 range up to 25%. From a starting point in the late 1960's when manufactured gas supplied a small but important proportion of the non-transport energy market - less than 3% - we have exper- ienced an average growth of nearly 24% per annum up to the present time.

Jan 1, 1982

Abouleid,A.F.327 Ajdic, I.451 Albert, L.F. 221,307 Alem, A. 525 Asama, T. 431 Avgherinos, P. J. 373 Baker Jr, C.N. 331 Balossi Restelli, A. 171 Beckwith,G.H.33 Bellini, A. 469 Bermingham, P. 481 Bertero,M. 171,535 Beyer, M. 503 Bottiau, M.41 Botto, G. 205 Bruskeland, O. 337 Budhu, M. 349 Bullivant, R.A. 181 Bustamante, M.G. 185, 475, 535

Jan 1, 1994

By Miller D. R

The mineral exploration and extraction industries have gained major cost and efficiency benefits from the use of computers. However these industries are now at a cross-roads with two seemingly disparate developments - that of an increasing number of complex geoscience databases and, at the same time, the merging of all known data for the particular regions at minimal cost. These two developments can be managed by the development and of an industry accepted geoscience data model and dictionary. This will provide a common basis of understanding for geoscience data through a common language and a common structure for geoscience information. Integration of specialist systems and databases can then proceed efficiently. The development of a data model is going ahead with consensus from the mining industry. This is a joint government and industry funded project and managed through the Australian Mineral Industries Research Association, AMIRA. AMIRA is a well known research broker to the Australian mining industry obtaining sponsorship for projects both from private and government groups. The AMIRA project, P431, called the Geoscience Data Model, is to be the Australian standard data model for geoscience disciplines. The requirement for a standard geoscience data model has been recognised in Australia for some time. In October 1991, the Australian Government Geoscience Database Policy Advisory Committee (GGDPAC) established a Geoscience Data Standards Working Group which drafted a comprehensive list of data categories of the geoscience area. An AMIRA project called AMDEX was established to develop a transfer standard for the mining industry data at about the same time as this committee was in operation. The first AMDEX sponsors meeting was held in May 1991. It was proposed to use the US Spatial Data Transfer Standard (SDTS) as the basis to transfer mining data in AMDEX. A limited data model of mining data to be transferred was developed for the AMDEX standard under SDTS. The Australian Geological Survey Organisation (AGSO) saw the need to extend this and develop a complete data model for the geosciences and proposed this as a new project to AMIRA. This was strongly supported by GGDPAC which lead to sponsorship of the project from most state geological surveys. The Geoscience Data Model can be broken down into separate data models for a number of geoscience themes and sponsorship obtained so far will enable models to be developed for a comprehensive set of themes selected by the project sponsors. Further sponsorship is required to enable a more complete coverage of the geoscience area to be developed. Sponsorship for the Geoscience Data Model has been strong from the geological surveys and there was some effort by GGDPAC to promote the project in these organisations. An Australian geoscience data model is of immediate use to the geological surveys in assisting the standardising of huge quantities of geoscience data held by government agencies and it is preferable that this be an Australia-wide standard.

Jan 1, 1995

By Hans Ruge

The El Soldado copper mineralization occurs as relatively high-grade irregular ore bodies with assay contacts and with frequent inclusions of barren rock. The sampling method must be timely for production grade control purposes, as well as accurate and inexpensive. Sampling techniques evolved from sampling dump cars at the haulage level to sampling scooptrams at the loading pockets. These were abandoned in favor of sampling production blast holes. Several sampling alternatives are discussed. These involve the selection of optimum volumes and sampling frequencies while taking into consideration geological parameters and statistical analyses of sampling data.

Jan 1, 1984

By Agne Rustan

Most of the mines in Sweden are metal ore mines in hard rock and none of these mines are classed gassy because there is no methane emission. The risk of methane explosions in Swedish mines is therefore very small. Since the 1960?s, in Swedish mines, there has been a change from electric and pneumatic loaders and transport machines to diesel. Today in almost all Swedish underground mines diesels are used. One of the most common complaint from the underground mine- workers is the exhaust gases from the diesel-vehicles. This is a strong motive for attempts to assure a more comfortable environment. Another motive for a better efficiency of ventilation under ground is the increasing cost of energy for fans and for heating the air during winter. For the largest mine in Sweden, the Kiirunavaara Mine, 36% of the energy for ventilation is used for preheating the air during the seven months when the temperature is below zero. The air quantities used for ventilation are large. In table 1 a comparison of the ratio between yearly produced ore and waste rock and installed fresh 'air capacity is shown. [ ]

Jan 1, 1980

By S. Joshi, E. Asselin

An electrochemical quartz crystal microbalance (EQCM) was used to study the leaching of pure gold in deaerated 1 M Na2S solution. Multiple cyclic voltammograms were measured between -0.76 and 1.242 V (SHE) at 20 mV/sec and 2 mV/sec and the frequency shift of the quartz crystal was simultaneously measured. Both the forward and reverse scans showed oxidation occurred between -0.40 to 0.20V. The frequency shift increased during both the forward and reverse scans in the potential range of -0.40 to -0.06 V indicating electrode mass decreased. Since at -0.40 to 0.20 V oxidation peaks were also observed, part of the oxidation was due to oxidation of gold. Eh-pH diagrams were constructed and showed soluble Au(I)-S(IV) species formed between -0.30 and 0.10 V (SHE). Atomic absorption spectroscopy of the test solutions and the mass change recorded by EQCM both showed about 0.015 mg of gold leached. Since the majority of the frequency shift increase corresponding to gold oxidation occurred at -0.40 to -0.06 V during multiple cyclic voltammogram measurement, the total leaching of gold could be approximated to occur at this potential interval to give a leaching rate of ca. 6.4x10-5 mg/s-cm2.

Jan 1, 2011

By Gustave E. Behr

The peculiar and changing conditions of a wartime market and the necessary governmental restrictions have resulted in an accumulation of a large amount of certain secondary metals in the tin-lead alloy class. With certain of these metals this accumulation has reached such proportions that it has been proposed that government agencies finance the creation of stockpiles of these secondaries just as stockpiles of primary metals have been created. The purpose of such financing would be to keep the secondary metal dealers engaged in collecting these metals, which they might

Jan 1, 1943

Slovenliness is as reprehensible in words as in clothes. Much writing that we recognize as poor in style is merely sloppy. Just as some students postpone the necessary shave or forget to change their collars, so young engineers in writing drop their articles, definite and indefinite, or omit prepositions where they are required, possibly to compensate for those they use unnecessarily The work will begin [on] Saturday. Influenza seriously affected many mines [during] the last three months. Flotation in America [during] the last two years has made tremendous strides. Construction of the mill started [on] August 12, 1915, at which time 75% of the excavation was completed. The idea I wish to convey is [that] there are mineral deposits to which the present law applies badly. For this reason, if there was [for] no other, the ownership of the ore below and [of] the surface above should go together. When a unit of mapping is furnished, be the unit a claim or [a] group of claims, it is necessary . . . A fully stocked store was started in Park City and all employees [were] sold merchandise on a strictly cost basis. The word "merchandise" is left without government or agreement. 'I suggest: ". . . and merchandise was sold to all the employees on a strictly cash basis." The verb 'be' is serving concurrently both as a principal and as an auxiliary in the following: At first the work was interesting and [was] liked by most of the men. The sulphide ore was more complex or [was] milled at an increased cost. The failure to repeat the auxiliary verb in successive clauses is a common error, as in The filter is filled with liquid allowed to empty, and then ignited.

Jan 1, 1931

By K. Law

"The Hatch Product Transport (HPT) system is a highly flexible and configurable route selection and sequencing system for controlling large bulk material handling facilities. The system has a generic control algorithm that can be configured to suit any material handling facility. It can also be easily reconfigured to cater to plant expansion or modifications without incurring significant disruption to the existing production, costs in testing, and re-commissioning, thus achieving cost savings throughout a facility’s lifecycle.This new material handling control system has been installed at BHP Billiton’s Port Hedland iron ore terminal to facilitate its expansion to beyond 100 Mt output capacity."

Jan 1, 2006

By Lane White

Environmental regulations have become a decisive factor for many minerals industry operations. Managers face new liabilities as a result of environmental laws, and restrictive permitting requirements for new projects make mine development an increasingly difficult proposition. An abundance of federal, state and local environmental laws and regulations already confront on-going minerals operations, and complex new legislation and rule-making is always in progress. Acronyms and initials like RCRA, CERCLA, SARA and EIS become as familiar as reserves, tons, grades and recoveries. The growth of such regulation has created a new category of professional employees - environmental scientists and engineers-whose presence will influence minerals production activity from now on. The disciplines of environmental science and engineering are still being defined. While these definitions are being worked out, companies in the minerals industry have responded by hiring people with professional experience in existing disciplines and training them to their special needs. An environmental consulting industry of substantial proportions has developed to offer expertise where producing companies may not find it economic to hire full-time professionals. The mining schools have responded by introducing environmental course work, but these programs have yet to supply a significant number of environmental professionals to the minerals industry. To gain some perspective on where minerals producers now stand in their hiring of environmental professionals, ME recently surveyed 20 companies, with questions about how they go about the business of managing environmental compliance. Twelve companies re¬sponded to the survey, and the results

Jan 1, 1991

By Mazandarani M, Chabot L, Vichion K

Pitch-steering models have been developed for discretely advanced mining machines (such as heading machines and coal shearers) using small-angle geometry and there are illustrative examples of simulator predicted performance. Although simple linear models result from the analysis of open-based machines, sledge mounted machines require execution of a Linear Programming energy minimisation to determine the attitude of the machine base at each advance over the previously cut floor steps. An analytical approach is based on elastic beam concepts developed for such applications as longwall face conveyors, caterpillar tracked machines such as continuous miners and longhole drills. Simulation results for longhole drills show the expected performance of an automatic guidance system and the destabilizing effects of sensing deviation too far behind the drill bit. Certain drill bit boundary conditions are expected to assist TBM. steering studies in three dimensions.There is a real role in mining machine steering for the mathematical models used in flight simulators.

Jan 1, 1991

By D. R. Hanson

The acoustic vibrational spectra of impacted rock slabs were examined at the Denver Research Center, US Bureau of Mines, in an attempt to characterize the behavior of partially detached mine roof rocks. The ultimate goal of this study was to develop a technique or instrument that could provide a quick, accurate, quantifiable measure of mine roof stability. The power spectra of unstable rock slabs were found to contain more energy in the range of 200 to 1000 Hz than solid rock. Comparison of the power contained between 500 and 1000 Hz with that between 3000 and 3500 Hz provided a quantitative measure of rock stability. A lightweight prototype field instrument was designed, constructed, and field tested. This battery-powered instrument computes the power contained in the two frequency bands, compares their magnitude, and displays a number related to the stability of the block tested. Field tests showed the instrument provided reliable measurements of block stability even under conditions of noise that would have seriously degraded the accuracy of the standard methods of roof sounding.

Jan 1, 1986

By A. Lubinski, C. R. Stewart, K. A. Blenkarn

Storage porosity has been considered one of the important pore geometry characteristics of heterogeneous-porosity limestones. Storage pores are only containers for fluids, in contrast to flow channel pores which both contain fluids and provide continuity for fluid flow. The concept of another geometry characteristic, "poro-striction", is presented as a second pertinent variable in describing limestone pore space. In simple terms, poro-striction is a measure of the flow resistance between storage and flow channel pores. Alternating-flow core-testing theory provides flow relationships which can be used to divide the pore space of heterogeneous-porosity media into flow channel and storage pores and to measure the "porostriction" of the latter. Experimental application of this theory to naturally occurring heterogeneous limestones shows that "porostriction" and the ratio of storage to flow channel pores can be estimated. Porostriction and porosity ratio are microscopic characteristics which should influence oil-recovery efficiencies during certain types of displacement processes. A knowledge of pore geometry should be valuable in designing or selecting the most effective oil-recovery process for heterogeneous limestones containing storage porosity. INTRODUCTION The primary and secondary recovery of oil from limestone (carbonate) reservoirs has been and will continue to be a major source of the world's supply of petroleum. Oil recovery from this type of formation is strongly influenced by the size, shape and arrangement of the pore spaces which hold the formation fluids. Therefore, it is expected that better knowledge of pore geometry would lead to design of more effective recovery processes. The concept of storage and flow channel pores has been presented as an important characteristic of limestone porosity.1 In this concept, storage pores are only containers for fluids, whereas flow channel pores are those pores which both contain and transmit the fluids. The work reported herein involves the concept of an additional pore characteristic called "porostriction". This characteristic can be visualized as the flow resistance between the storage and flow channel pores. This resistance is an important pore geometry characteristic because it determines how easily gas and oil can replenish fluids removed from the flow channel pores. Fatt and co-workers at the U. of California have studied the effect of storage porosity and a factor similar to porostriction on transient-flow response of models of porous media during a pressure build-up or drawdown test.55 These models consisted of porous sandstone cores with artificially simulated storage pores. It is the purpose of this paper to describe tests which permit the storage porosity and porostriction of actual reservoir core samples to be estimated. The tests used for this purpose involved not transient tests but, rather, an alternating-flow technique in which pressure and flow are varied according to a sine-wave relationship. This technique may offer advantages over transient methods. THE POROSTRICTION CONCEPT Before discussing alternating-flow (A.F.) tests in core samples, it is necessary to define the porostriction parameter. For this purpose attention is focused upon an elemental volume v representative of a porous medium having both flow channel pores and restricted-access storage pores. For such an elemental volume, it is considered that the storage porosity is combined to form a single pore and that the access into the storage porosity may be represented by a single capillary tube connecting the single pore to the flow channels of the elemental volume. Let the radius of the capillary tube be designated as Rc and its length as L,. When fluid flows into or out of the pore, the following equation (Poiseuille's law) relates flow rate q to pressure drop p, and the physical characteristics of the tube and the fluid of viscosity jx.

By F. F. Aplan

Estimations have been made of the tonnage of raw ores and coal treated by various beneficiation processes. The amount treated by gravity concentration is substantially greater than that treated by flotation, with coal representing the bulk of the material treated by gravity means. A discussion is given of the trends and anticipated improvements in gravity methods. Except for the concentration of iron ores, magnetic and elec- trostatic separation processes find their greatest use in the beneficiation of non-sulfide ores. Exciting new developments in magnetic materials and separation process (and, to a lesser extent, in the electrostatic process) indicate a substantial increase in the application of such processes to ores and a broad variety of non-ore uses.

Jan 1, 1989