Search Documents

Joseph K. Stone, Jr. (Kaiser Engineers, Oakland, Calif.)—I would like to compliment the authors on their clear presentation of the results of their study of the pneumatic processes. We hope that the Inland Management decision to make this information available to all will induce others to release additional valuable fundamental data which they have accumulated in the field. There are two points upon which we would like to comment. In the discussion of Table VII it was indicated that the "oxygen consumptions were about the same as has been reported for other oxygen steelmaking processes". This conclusion is apparently based upon the consumption of 2100 cu ft per ton shown in Table VII. The data in Table IV also permits calculation of 2520, 2280, 2250 and 2700 cu ft per ton in heats 1 to 4, respectively. These figures are in the same general range as those reported for the Kal-Do and Rotor Processes using Thomas iron, but considerably above the following figures for four of the operating L-D Process Plants while using iron which is similar to American basic iron: Donawitz 1760 cu ft per ton Adapted from Cuscoleca' LinZ 1900 cu ft per ton Trenkler & Hauttmann2 Dofasco 1850 cu ft per ton D. O. Davis:3 In addition to the differences between the consumption of gaseous oxygen in the Inland operation and in the L-D Process, there is another closely related difference. The L-D plants for which data are cited are using approximately 1 pct ore while the authors' process used about 7 pct of sinter. Assuming 65 pct Fe in the sinter, the difference amounts to 400 to 500 cu ft

Jan 1, 1959

By Kenneth S. Ritchie

The natural emulsion samples used in this study were shipped directly from twelve California oil fields, through the courtesy of the superintendents of the main producing companies in those fields. Representative parts of each sample were chosen for the slides. Preparation of the slides was generally made in less than two minutes, including time of exposure; in a few cases, about five minutes was required. The short time was intended to minirmize the changes in conditions. Whenever comparison was of value, standard conditions were established. Spreading by gravity was adopted instead of smearing. Cover glasses were not allowed to rest on the films. General Characteristics of Emulsions The main purpose of the general views (Figs. 1-16) is to illustrate the general characteristics of the dispersed droplets together with any other constituent or impurity that may be found in each emulsion. The magnification is given so that dimensions could be measured from the plates. The slides used for these views had spherical recesses; they gave the best light. Where crystals were intended to be shown in the picture a filter (green was the best') was usually used. Emulsions that showed a tendency to move by concentrated light were pictured without a condenser.

Jan 1, 1931

By G. Heinrichs

This paper is intended to provide information for one to be able to determine the slurry system head curve for pump applications. The slurry characteristics are the basis for what the size, material of construction, and critical carrying velocity of the pipe will be. The system head curve is adjusted by use of the pipe friction coefficient factor and slurry derate factors. An example using multi-staging of slurry pump curves is presented to compare the wear life relationship of pump parts for a tailing pipeline system head curve.

Jan 1, 1996

By K. P. V. Lei

The Bureau of Mines as part of its research effort to minimize the generation of hydrometallurgical waste, investigated a sodium sulfide leaching-electrolysis procedure for treating hydrometallurgical residues for elemental sulfur and base-metals recovery. Research was conducted on a leaching residue from a lead concentrate. The following procedure was developed. 1. The elemental sulfur was dissolved as polysulfide with an Na2S solution. 2. The resultant metal sulfide bearing residue was oxidatively acid leached in a cationic membrane electrolysis cell; the metals were solu¬bilized at the anode, and a base was generated at the cathode. 3. The elemental sulfur was recovered from the polysulfide solution by neutralizing with the acid in the anolyte. Byproducts of the neutralization were H2S and a sodium salt solution. 4. Sodium sulfide was regenerated by reacting the H2S byproduct with the base in the catholyte. 5. Lead as PbCL2 was recovered from the anode residue by brine leaching, and the other metals were recovered from the sodium salt solution as metal sulfides. 6. The barren filtrate from the metal sulfide precipitation constituted the recycled electrolyte. Ninety-eight percent of the elemental sulfur, 98 pct of the lead, and up to 80 pct of other accessory metals were recovered from a residue obtained from the FeCl3-NaCl leaching of a lead concentrate.

Jan 1, 1982

New York Holds monthly meetings, except June, July and August JOHN A CHURCH, JR, Chairman JOSEPH E POGUE, Vice-chairman SIDNEY ROLLF, Vice-chairman EDWARD C MEAGHER Secretary, Texas Gulf Sulphur Co, 41 E 42nd St, New York M H MERRISS, Treasurer, 42 Broadway, New York ARTHUR NOTMAN T T READ Boston Meets first Monday of each winter month EDWARD C GEITHER, Chairman WILLIAMS BLACK, Vice-chairman DONALD H MCLAUGHLIN, Secretary-treasurer, Rotch Bldg, Harvard Univ, Cambridge, Mass J L GILLSON A G WAITD

Jan 1, 1923

By C. W. Crispell

The four nomograms presented in this article were designed to simplify and make more rapid the calculations connected with the compression and transmission of air. The formulae involved are rather complicated, but the graphic solutions are simple; their use requires an ability to follow explicit directions and to interpolate values on a logarithmic sca1e. † For the sake of convenience, the nomograms will be divided into two classes, and the purpose and accuracy of each will be discussed. Power foR CompREssion It is frequently desirable to determine the horsepower necessary to compress a given amount of free air from atmospheric pressure to a certain final pressure. The nomograms in Fig. 1 and 2 present a rapid method of calculating the horsepower required to compress 1 cu. ft. of free air per minute by single or two-stage compression. The general formula for the horsepower required to compress air adiabatically is: S X 144 PVn [(P')n-1/sn -1 (1) where: P = absolute atmospheric pressure at compressor, in pounds per square inch. P' = final absolute pressure of compressed air, -in pounds per square inch. V = volume of free air compressed per minute, in cubic feet. S = number of stages. n = exponent of the compression curve.

Jan 1, 1918

By P Myers, T Elkington, S Wonday

Sierra Rutile LimitedÆs (SRL) heavy mineral sand mining operation in Sierra Leone, West Africa, is embarking on a new phase of its life. After confronting many challenges during the 1990s and 2000s, SRL is embarking on a strategy of growth to recover maximum value from the mine over the rest of its life. Sophisticated linear programming techniques have been used to develop an optimum strategy for extracting SRLÆs many known deposits of economic grade, while considering options for expansion and for a variety of mining and processing methods and combinations. CITATION:Myers, P, Elkington, T and Wonday, S, 2012. Strategic optimisation at Sierra Rutile - A case study in maximising project value, in Proceedings Project Evaluation 2012 , pp 59-66 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By T. A. Oberhellmann

The Wobbler Feeder is a comparatively new materials handling and separating device. It is essentially a materials separating or scalping machine, particularly adaptable to separation of oversize particles from mine-run ore and to the separation of oversize materials from overburden, where the removal of oversize materials is necessary, as is the case in conveyor stripping. In construction, the Wobbler Feeder is simply a set of transverse bars of manganese steel, or other wear-resisting alloy steel, each having an elliptical cross-section with the major axes of adjacent bars displaced by ninety degrees so when rotating in unison, the pre-determined space between the bars remains constant.

Jan 1, 1959

By Lev Filippov, Saeed Farrokhpay

"Flotation process has had less success to recover nickel from laterite ores. Nickel in laterite ores is often finely disseminated in various minerals in very fine size. Therefore, fine grinding should be used to liberate nickel containing particles. Particles resulted from fine grinding are often very fine, and recovery of such particles is generally low using conventional flotation methods. One option to overcome this problem is enhancing the particle-bubble interaction by increasing the particle size and forming flocs. Selective flocculation of fine particle can be therefore the key to enhance the flotation performance of low grade laterite ores.INTRODUCTIONThe majority of the world’s nickel resources occur as laterite ores which are complex, low grade and expensive to treat using conventional smelting and high temperature and/or high pressure autoclave methods (Xu et al., 2013). While about 70% of the nickel resources are contained in laterites, only 40% of the world’s nickel production comes from these ores. Researchers have tried to improve the nickel laterite flotation recovery by using a number of feed preparation techniques. For example, in a study on a laterite ore sample from Australia, flotation tests on a narrow sized fraction of 38-75 µm resulted in only a small increase in the nickel content, from 1.0% to 1.4% (Quast et al., 2015a). In fact, no physical separation technique (including flotation) has been able to dramatically upgrade nickel in laterite ores (Quast et al., 2015b). Thus the challenge of processing low grade nickel laterite ores still exists. This paper aims to explore the possibility of applying selective aggregation in pre-concentrating of valuable minerals in nickel laterite ores."

Jan 1, 2016

By Yasuhiko Ito

"This talk is concentrated on the topics of compound film formation on the substrate electrode by interdiffusion of substrate element and electrochemically deposited species and/or by direct electrochemical implantation of the component element of the film into the substrate. As a typical example, electrochemical implantation of nitrogen atom into Ti metal to form TiN surface film is described. Another example is the formation of various kinds of intermetallic compound films including Ni2Y, Ni2Dy and Pd3 Y by the electrochemical implantation of lanthanoid elements into transition metal electrodes. By combining these two methods, Sm-Fe-N ternary material film also could be formed. The principle and application of the ""electrochemical implantation"" are discussed in detail.IntroductionGenerally speaking, surface film formation by molten salt electrochemical process can be divided into the following three categories:(i) single element film formation on the electrode by electrodeposition,(ii) compound film formation on the electrode by electrocodepostion of more than two elements, and(iii) compound film formation on the substrate electrode by interdiffusion of substrate element and electrochemically deposited species and/or by direct electrochemical implantation of the component element of the film into the substrate.This talk is .concentrated on the topics of category (iii), especially on the electrochemical implantation. Typical example can be seen in the electrochemical implantation of nitrogen atom into Ti metal to form TiN surface film. Another example is the formation of various kinds of intermetallic compound films including Ni2 Y, Ni2Dy and Pd3 Y by the electrochemical implantation of lanthanoid elements into transition metal electrodes. By combining these two methods, Sm-Fe-N ternary material film also could be formed. The principle and application of the ""electrochemical implantation"" are discussed in detail with examples above as well as other experimental results also obtained very recently in the author's laboratory."

Jan 1, 2000

By D K, S Freij, A Rossiter, X Han, B Feng

In mining operations, the removal of overburden to expose the ores is achieved by rock blasting using ammonium nitrate based explosives, eg ammonium nitrate-fuel oil mixtures, commonly known as ANFO. However, ammonium nitrate can react with pyritic shales that are often found in many mines, leading to premature detonation or spontaneous explosion. In order to minimise the occurrence of spontaneous explosion, the reactivity of the shale in a mine must be assessed. This will provide a better understanding of blasting risks and thus will improve the safety and the cost efficiency of blasting through the selection of appropriate explosives. In this study, shale samples were collected from different locations in Western AustraliaÆs Mt Whaleback iron ore mine and geochemically characterised. The reactivity of the shale samples towards ammonium nitrate and ANFO was investigated using a combination of large-scale firing range tests and laboratory isothermal reactor tests. Results of the firing range tests show that the reactive ingredients of the shale are the limiting factor for the reactions between shale and ANFO. Based on the firing range test results, further isothermal reactor tests were conducted to investigate the reactivity of shale samples towards ammonium nitrate under controlled conditions. Analysis of the results from the firing range tests and the isothermal reactor tests shows that there are correlations between the reactivity of shale samples and several geochemical characteristics such as sulfate, sulfur, ferrous and zinc content.

Jan 1, 2005

By Mirabediny H, Whitchurch K

A computerised simulation model has been developed to select the most suitable digging method of a dragline operation for a given geological condition. The developed procedure uses a geological ore body model as the basis for the geologic database. The simulation selects the most cost effective dragline digging method from a database of various dragline digging methods The database consists of common and innovative dragline methods currently used in Australian open cut mines. A generalised computer package, DSLX, was extensively used to simulate various dragline digging methods. The DSLX software uses predefined functions to build strip geometry, working benches, blast profiles and spoil piles. The outputs from DSLX in form of volumetric, swing angles and hoist distances data are then aggregated with dragline specifications and site time study data to compare productivity of selected digging methods. The result of a case study showed that this procedure lends itself to the 'optimum' selection a dragline digging method for a given coal deposit.

Jan 1, 1995

Some crystal chemical properties of several apatites from Brazilian deposits and occurrences were determined; the samples had different origins (igneous, metamorphic and sedimentary). The aim was to establish relationships to their froth flotabilities behaviour. Detailed X-ray diffraction studies were carried out, to determine precisely the unit cell parameters and the degrees of crystallinity of the apatite samples. A thorough chemical analysis of these minerals was also conducted. Microflotation studies were carried out, using sodium oleate and dodecylammonium chloride as collectors. The crystallinity levels were determined for all samples studied, with the establishment of a crystallinity index, which varied from 10.0 to 4.5, on a normalised scale. A marked dependence was observed between this crystallinity sequence and flotability; for both collectors, flotability dropped drastically for crystallinity indices lower than 8.0. Also, the low crystallinity apatites showed a decrease in floatability, for longer conditioning times.

Jan 1, 1993

By L. M. Cumming

"The contact between dolomite of the St. George formation (Cambro-Ordovician) and limestone of the overlying Table Head formation (Middle Ordovician) is a regional disconformity. This is best illustrated from exposures on Pointe Riche Peninsula, near Table Point, and along Port au Port Bay. The contact occurs along 180 miles of the west coast of Newfoundland from St. John Island in the north to the western part of Port au Port Peninsula in the south. A disconformity of the same age occurs between the Romaine and Mingan formations on the north side of the Gulf of St. Lawrence.Dolomitic beds beneath the disconformity locally contain concentrations of base-metal sulphides. Sphalerite occurs in dolomite pseudobreccias of the St. George formation at Zinc Lake, 7 miles northeast of Daniels Harbour. The 'Western Newfoundland Lower-Middle Ordovician regional disconformity is interpreted as having originated on and near the edge of a broad platform, and to have provided an important regional geological control in the localization of zinc mineralization."

Jan 1, 1968

By Archie Richardson

The trona mines in the Green River Basin, commonly known as the "trona patch," present an interesting set of rock mechanics issues stemming from mining in a unique underground environment. Like other minerals occurring in tabular deposits, trona is mined using high-productivity room-and-pillar and longwall methods. However, trona does not behave quite like other evaporites and behaves far differently than coal. In this paper, the following key issues in trona patch rock mechanics are discussed: material properties, in situ stress field, water and gas pressure effects, creep characteristics, pillar behavior, roof span stability, floor stability, underground tailings storage, longwall mining, two-seam mining. and solution mining. Many of the existing trona producers are entering potentially more difficult mining conditions, and much consideration is being given to "new" technologies such as longwall mining and solution mining. In analyzing 20 years of experience with trona patch rock mechanics issues the authors have identified key comparisons and contrasts with conventional tabular deposit rock mechanics that will help illuminate what has been learned as the trona patch enters the 21" century.

Jan 1, 1999

By Ralph Bernstein

The processing of earth observation sensor data by digital technology is almost two decades old. Only recently, however, has this technology become practical and economical. The reasons for this are interesting to analyze, and they provide some insight into what the future may bring. Some of the earlier activities and their limitations, current systems and their applications, and future technology direction are summarized.

Jan 1, 1979

By Duk-Won Park, Syd S. Peng

For an adequate design of the shortwall face support, it is necessary to understand fully the support- roof interaction. A series of studies has been carried out at a shortwall panel to develop the methods of monitoring support resistance and determining load density of the chocks. Various aspects of applications, for improvement of chock design and understanding of roof conditions, are discussed.

Jan 1, 1981

By M, C Silveira, C Ellice, D Christensen

Peak Gold Mines (PGM), a member of the Rio Tinto Group, is an underground and open cut gold mining operation located near Cobar, NSW. A multi-phase study was initiated in 2001 in support of developing a dry æmoisture store and releaseÆ cover system design for the PGM tailings dam, which contains potentially acid-forming tailings material. The first phase consisted of characterising the tailings and potential cover material (waste rock from an open cut operation) as well as soil-atmosphere cover design modelling. The second phase involved construction of two cover system field trials on the tailings dam and installation of a variety of field instruments to monitor the hydraulic performance of the test covers during all seasons of the year. Field performance monitoring commenced in April 2002 and will continue for a minimum of two wet-dry climate cycles (third phase), prior to using the field data for calibration and subsequent validation of numerical models developed for the cover system trials (fourth phase). This paper describes the work completed for the first two project phases and also discusses the initial performance of the cover system trials.

Jan 1, 2003

By Faruk Oksuz, Dave Schiemann, Matt Trotter, Mike Padilla, Miguel Sanchez, Carmen Scalise

"Chicago’s Tunnel and Reservoir Plan (TARP) is a nearly $4.0 billion and over 30 years long program and arguably the largest and longest combined sewer tunnel and reservoir system in the world. Recently, a massive tunnel construction is underway for connection of the McCook Reservoir to the existing TARP tunnel system. Once completed in two stages in 2017 and 2019, the reservoir will hold 38 billion-liters (10 billion-gallons) of combined sewer overflows (CSO) and flood waters from the city of Chicago and over 20 communities in Cook County, Illinois. McCook Main Tunnel will connect Chicago TARP’s Mainstream Tunnel to the McCook Reservoir. Connecting two 10-meter (33-ft) diameter tunnels at 92 meters (300 feet) underground has not been a simple task for the McCook Tunnel Project participants, the project owner U.S. Army Corps of Engineers (USACE), local sponsor Metropolitan Water Reclamation District (MWRD) of Greater Chicago, designer Black & Veatch, and the contractor, Kiewit Infrastructure Company (Kiewit). Yet alone excavating and lining massive size tunnels, the team is also challenged with live tunnel conditions in TARP Mainstream Tunnel that carries CSO and flood flows from city of Chicago which runs full during rain events and must remain in service at all times. The project is a noteworthy feat for engineering and construction with the upcoming installation of world’s largest underground wheel gates for flow control within the tunnel. In this paper, we describe one of its kind elements of this major tunnel system along with key design and construction considerations, specifically for the live tunnel connection which is a rare occurrence in the tunneling industry. INTRODUCTION The McCook Main Tunnel system consists of a 10 m (33 ft) finished diameter and 490 m (1,600 ft) long hard rock tunnel constructed from a 27.5 m (90 ft) diameter and 92 m (300 ft) deep main gate and tunnel construction access shaft. The gate shaft houses six high head 4.4 m by 9 m (14.5 ft by 29.5 ft) wheel gates to be installed in the bifurcated and steel lined section of the tunnel. The tunnel also includes portal and energy dissipation structures as it daylights into the reservoir."

Jan 1, 2016

By Monique Pharand, Jeet Basi, Simon Hille

"High quality activated carbon is essential in the recovery of gold in Carbon-in-Leach (CIL), Carbon-in-Pulp (CIP), and Carbon-in-Column (CIC) circuits. Goldcorp’s Campbell complex at Red Lake Gold Mines (RLGM) experienced a period of low soluble gold (Au) recoveries during Q3 2013, during which time the processing plant saw higher than typical Au grades in the CIP tails solution stream. A technical review identified that the CIP circuit may be experiencing a carbon-fouling issue. To further understand the degree of fouling, and to troubleshoot the low recovery problem, samples of carbon were collected from the CIP, elution, acid wash, and regeneration circuits, and submitted for characterization test work. This paper summarizes the steps taken to remedy the carbon-fouling problem at RLGM resulting in increased overall Au recovery.Overview of Red Lake Gold MinesRed Lake Gold Mines is located approximately 450 kilometres northeast of Winnipeg, Manitoba, in Ontario’s western boundary region.All mining is carried out through underground operations, utilizing overhand cut and fill, underhand cut and fill, and long-hole mining methods. Ore types include: silica-replaced carbonate veins with free milling gold, siliceous replacement-type mineralization (rich with arsenopyrite) marginal to veins, broad disseminated sulphide mineralization along major shears, and some minor sulphidized chemical sediment-hosted ore. The operation is supported by two milling complexes: Red Lake, and Campbell.Process DescriptionThe Campbell processing plant's main unit operations consist of grinding, gravity concentrating, flotation, autoclaving, leaching, carbon-in-pulp (CIP), carbon elution and reactivation, electro-winning, bullion smelting/refining and cyanide destruction, and concentrate handling. A schematic of the plant flowsheet is shown in the figure below.BackgroundHigh quality activated carbon is essential in the recovery of gold at many CIP/CIL/CIC processing plants. At RLGM, gold-bearing ore is milled and cyanide is added to leach the gold from the solids into solution. The dissolved gold then comes into contact with activated carbon, and adsorbs onto its highly porous surfaces. Gold is then recovered by separating the activated carbon from the main slurry for further refining. As such, the characteristics and quality of the activated carbon have a significant and direct impact on overall gold recovery."

Jan 1, 2016