Search Documents

By Brunella Recinto

Pile loading tests are carried out with two main objectives: 1) evaluating the ultimate resistance; 2) checking the behaviour of the pile under live load. In the first case and particularly for large diameter bored piles the cost of a loading test may be very high. In the late '80s, a new method to perform static loading tests was proposed. It is based on the use of a sacrificial hydraulic jack placed at the pile toe. The device, internally pressurized, expanding applies an upward force on the pile shaft and an equal but opposite downward force on the soil beneath the pile toe. This device is well known as Osterberg's load cell, shortly O-cell. The obtained results are typically summarized in two separate load-movement curves: one for the shaft side shear resistance and another for the toe resistance. The two curves are used to build what is generally named the "equivalent head load-movement curve" relying upon two hypotheses: - the pile is rigid; - the load movement relationship for the shaft is not affected by the direction of movement. The former assumption can be easily removed, while it is not possible to remove the latter. On the validity of this latter hypothesis, comparisons between conventional head loading tests and toe loading tests could be very helpful. Unfortunately in the literature there are only a few case histories and most of them are also poorly documented. In order to explore limitations and potentialities of the new testing method, a finite element model has been set up. Results of simulations of conventional head loading tests and of O-cell tests are analyzed, discussed and compared.

Jan 1, 2003

By Ronald D. Hill, Elmore C. Grim

Coal-haul and mine access roads are defined as any road constructed, improved or used by the operator (except public roads) that ends at the pit or bench. These roads constitute approximately 10% of the total area directly disturbed by the surface mining operation(l). In some cases, the land disturbed by haul roads exceeds the area included in the mining operation. Studies (2 and 3) of the U. S. Forest Service in eastern Kentucky show that typical contour mining roads exhibit poor alignment, excessive grades, insufficient strength and durability, and poor drainage. Mine roads in other Appalachian- States, particularly where contour mining is practiced, appear much the same as those in Kentucky. Access roads(4) were also found to be a large source of sediment. It is possible that of the sediment that finds its way into the streams as much (or even more) originates from the haul roads as from the mining operation. Most roads are built as cheaply as possible, and good road-building design and practice are ignored. Maintenance schedules are generally inadequate, and upon completion of mining, haul roads are usually abandoned, with little or no attempt made to bed them down(5 ) . Such roads deteriorate very rapidly (Figure 68). Area mining, which is practiced in flat to gently rolling terrain, presents fewer haul road related environmental problems. These roads through necessity are generally well engineered because of the heavy equipment using them, such as 240 ton (217 metric ton) haul trucks. They must have wide beds, good alignment, and adequate drainage to permit coal haulers to run at top speed during all seasons of the year. Excessive dust can be a public nuisance and a driving hazard, and it is hard on equipment. Calcium chloride and sodium chloride have proven to be effective materials for controlling dust. Two applications during the summer when the ground surface is moist at the rate of 1/2 pound per square yard (.26 kilograms per square meter) (3 1 have been suggested. Th4 most common procedure is to keep the roads wet by using water trucks. Sediment that reaches the streams can be traced to one or more of the following five basic phases of haul-road life:

Jan 1, 1974

A numerical method for discriminating between replacement and sedimentary processes is applied to a folded stratiform sulphide occurrence. It is shown that numerical treatment of chemical analyses from a single diamond drill hole allowed a rapid assignment of the ore to the syngenetic sedimentary class and thereby enabled a revision of the evaluation program concerned with consequent reduction in costs.

Jan 1, 1973

By Greg Partington, Darryl Thorburn, Charlene Wildman, Elisa Puccioni, Connie Payne, Campbell McKenzie

"Mineral prospectivity modelling of polymetallic nodule deposits has been completed over the Cook Islands Exclusive Economic Zone (CIEEZ) using the GIS based Weights of Evidence modelling technique. Polymetallic nodules, also known as manganese nodules, have been explored as a possible resource for a number of metals including cobalt since the early 1970s. Recent data on the nodule composition and abundance in the CIEEZ has led to a renewed interest in the prospectivity for manganese nodules in the region. The predictive modelling has used the most recently accepted mineral model for polymetallic deep-sea nodule deposition to identify factors that are most likely to map the presence of this type of mineralisation in the CIEEZ.Manganese nodules form on the deep seafloor as concretions formed by concentric layering of iron and manganese hydroxides around a core and they grow at a very slow rate, on the order of millimeters per million years. The available data for the CIEEZ indicates a greater abundance in the area of nodules formed by hydrogenetic processes, which are the result of slow precipitation of metallic components from seawater. The environment in which the nodules are most abundant is at depths between 4,000 m and 6,000 m in areas of low sedimentation rate. Hydrogenous nodules commonly grow on siliceous and pelagic clay sediment, they are less common on other types of sediment."

Sep 1, 2014

By Daryl E. Radcliffe

Ninety-seven roof bolts were instrumented with strain gages and resin-grouted in three areas of the Bear coal mine, Somerset, Colo., by the Bureau of Mines. Measurements taken with these instruments indicate roof support is achieved through a combination of point suspension and resistance to vertical and horizontal stresses caused by localized shearing in the roof. The localized shearing results in bending of the bolts, yielding due to high vertical stresses, and the transfer of high loads to the bolt head or plate.

Jan 1, 1980

By G. J. Joy, J. P. Rider

"Technical advances in longwall mining over the last several years have resulted in much larger and faster shearers that have the capability of mining at speeds over 100 ft./min. This has resulted in a substantial increase in the amount of dust that is generated at the shearer and during shield advances. Meanwhile, increased underground coal production has put a greater demand on longwall dust control systems as some operators have had difficulty maintaining consistent compliance with federal dust standards. To address this need, the National Institute for Occupational Safety and Health [NIOSH] is investigating the effectiveness of a water spray manifold mounted on the tailgate end of the shearer body. The sprays are oriented parallel to the tailgate ranging arm, and these sprays create a water curtain confining the dust plume near the face, preventing the dust from drifting into the walkway. This redirection of dust provides a clean air envelope for the tailgate shearer operator and jacksetters working near the tailgate drum. Three different tailgate spray manifold designs were tested and evaluated at the Office of Mine Safety and Health Research [OMSHR] Pittsburgh Longwall Test Facility. Manifolds were equipped with hollow cone or flat fan water spray nozzles and evaluated at three face air velocities (500, 700, and 900 fpm) and at water pressures of 100, 150, and 200 psi. Reductions in dust concentrations were observed at six face sampling locations for all the tailgate manifold systems at each of the tested spray pressures and face velocities. Based on results from the laboratory tests showing reductions in dust concentrations at sampling locations downwind of the shearer a spray manifold was fabricated and evaluated at an underground operation. INTRODUCTION In 2012, underground coal mining in the United States produced a total of 342 million short tons, with longwall mining accounting for over 53% of this production [EIA 2013]. The longwall mining industry continues to see remarkable and significant improvements in longwall mining equipment and mining practices. Average shift production during compliance dust sampling has increased from 3,500 tons per shift in 1994 to approximately 6,000 tons per shift in 2012. A dramatic decrease in working longwall faces from 80 to 49 has occurred over the same period [Fiscor 2013]. Factors specific to longwall mines that supported productivity improvement include: higher capacity shearers, improved shield hydraulics and control, higher horsepower for equipment, wider face conveyors, and larger faces. Today, the average face width has increased to 1,188 ft., with one longwall operation reporting a face width of 1,650 ft. compared to an average of 750 ft. in 1994 [Fiscor 2009, 2014]. Panel lengths in 2013 averaged 11,307 ft. compared to 7,000 ft. in 1994. Overall production from U.S. longwalls has increased by nearly four percent from 2007 to 2012 with over 182 million tons mined annually [EIA 2013]. Given the volume and rate of coal produced on longwall faces, the potential to generate large quantities of respirable coal mine dust also exists."

Jan 1, 2015

By S. Litke

Elemental sulfur was stockpiled at the Mount Polley Mine for use as a source of sulfuric acid as part of research into leaching copper from oxide ores, but the project did not proceed beyond an initial pilot- scale evaluation. Since placement, the sulfur has oxidized and some sulfuric acid leached into the underlying rock. The reaction of the acid with these underlying materials has been studied as part of an evaluation of the effects of leachate from the pile. The rock underneath the sulfur pile is composed dominantly of primary and secondary alumino-silicates with less than 1% carbonate (calcite) and iron sulfide (pyrite). In its unaltered condition, the rock is classified as non-acid generating. Conceptually, it was expected the sulfuric acid would be neutralized by the rock to varying degrees resulting in a series of pH-controlled weathering fronts progressing from leached near the contact with the sulfur pile (pH <3), to active neutralization by silicates (pH 4–5), to active neutralization by carbonates (pH >7). The rocks underneath the pile were sampled to determine the extent to which the rocks had reacted and their long-term stability after removal of the acid source. INTRODUCTION When rock is blasted and excavated to facilitate mining ore, it is typically placed and stored on the surface in piles. The resulting drainage may have a neutral to basic pH (i.e., non-acidic drainage) or a low pH (i.e., acid rock drainage, ARD) depending on the mineralogy of the rock being stored in the piles. Acid- base accounting (ABA) can be used to characterise the two types of rock: potentially acidic drainage generating (PAG) and not potentially acidic drainage generating (NAG) (Price, 2009). According to Price (2009), NAG is defined as having an excess of neutralization potential (NP) in the rock in the form of calcium carbonate-like minerals when compared to acid potential (AP), i.e., a Neutralization Potential Ratio (NP/AP = NPR) greater than 2.0, whereas PAG is classified as having an excess of AP (i.e., an NPR less than 1.0). This is a conservative estimate and may be slightly modified depending on the mineralogy at specific mine sites. Rock with an NPR of 1–2 is also capable of generating acid (Price, 2009) and, depending on the mineralogy, may also be classified as PAG. Drainage from PAG material can generate acid immediately, or many years after it has been exposed to surface conditions. Disposal techniques depend on the category (i.e., NAG or PAG) and reactivity of the rock stored in the piles.

Jan 1, 2019

Phase equilibria studies have been carried out on the "FeO"-Si02-MgO-A120rCr203 system in equilibrium with iron in the range of compositions and temperatures directly relevant to the nickel laterite deposits being investigated by Xstrata Nickel within the Araguaia belt in Para State, Brazil. Liquidus temperatures and primary phase fields have been measured as a function of composition using equilibration, quenching and electron probe X-ray microanalysis measurements. The results are presented in the form of pseudo-ternary sections. It was found that in the composition range investigated, olivine (Mg,Fe)2Si04 and pyroxene (Mg,Fe)Si03 are major primary phases. In addition, tridymite Si02 and spinel (Mg,Fe2+)O?(Al,Cr,Fe3+h03 are also present in the higher Si02 and lower Si02 regions respectively. The results of the phase equilibria studies were validated in a subsequent pilot smelting test.

Jan 1, 2009

By Martin Rubenstein

CdS crystals have been grown from a number of metallic solvents such as bismuth, tin, lead, and cadmium. Etching studies have shown that plastic deformation occurs if the crystals are not removed from the solvent prior to the solidification of the solvent, on cooling. The deformed crystals show a umique exciton fluorescence as a function of edge dislocation density. If one grows the CdS in the eutectic alloy of the above four metals (commonly called Wood&apos;s metal) the crystals can be removed from the solvent with hot water and no plastic deformation occurs. In this paper, the liquidus solubility measurements of CdS, as a function of temperature, are presented. The data were obtained using a high -temperature filtration technique. CADMIUM-SULFIDE crystals have been grown from a number of metallic solvents1 such as cadmium, bismuth, tin, and lead. Liquidus solubilities of CdS in cadmium,2 bismuth,3 and tin4 have already been measured. Crystals of CdS, in all four metals, have been grown by solution growth: 1) by cooling a saturated solution and 2) by a solution transport method.1&apos;"1 CdS crystals grown in these four solvents have a few characteristics in common: 1) 1.8°K photolumines-cent emission consisted mainly of the radiative recombination of the bound exciton commonly known as I,, 2) slip lines which could easily be seen by the naked eye, and 3) edge dislocation densities in the order of l05 per cu cm.1 It was decided that these slip lines and the high edge dislocation densities were caused by a plastic deformation of the CdS crystals. It was felt that this plastic deformation did not occur during the growth of the crystals nor during the cooling of the solution, but did occur when the solvent which was in contact with the crystals froze. If these assumptions were valid, the slip lines and the high number of dislocations could be reduced or eliminated by removing the crystals from the solvent before the solvent froze. Since crystals of CdS had already been grown separately in such solvents as bismuth, lead, tin, and cadmium, it was felt that crystals could be grown in a eutectic mixture of these four metals. In this work a eutectic (or near eutectic) mixture of bismuth, lead, tin and cadmium in the proportion 50, 26.5, 13.5, and 10 wt pct, respectively, was used to grow CdS crystals. Such a mixture has a melting point of about 70°C and is close in composition to the alloy commonly known as Wood&apos;s metals. If the crystals could be grown from this mixture of solvents, and if hot water (>75°C) could be used to separate the crystals of CdS from the metallic solvent, it was hoped that CdS crystals could be grown with little or no plastic deformation which had been ob- served when crystals were grown from these solvents uncombined. CdS crystals were grown from this low melting eutectic mixture of bismuth, lead, tin, and cadmium using the solvent transport method. CdS powder and the appropriate amount of metals were sealed in a quartz tube under a pressure of about 5 X 10-6 torr. This ampule was then placed in a vertical position in a furnace. The temperature was raised to about 900°C. The furnace was designed so that the top of the liquid column within the ampule was between 10° to 40°C higher than the bottom of the liquid column. These temperatures were measured on the outside of the quartz ampule. The ampule was maintained at temperature for 7 to 14 days (depending on the temperature at which transport was taking place) and then the furnace temperature was lowered until the temperature was about 125°C. The ampule was then removed from the furnace, placed in water maintained at about 90°C, and opened in this 90°C environment. The crystals could then be removed from this two-phase liquid (Wood&apos;s metal and water) by mechanically picking them out. Alternatively, the crystals could be quantitatively removed by adding an excess of mercury to the mixture of metals, crystals, and hot water. The hot solution of metals and the hot water could be evacuated using a small diameter tube connected to a vacuum. Small amounts of mercury and water could be removed by heating the crystals in vacuum. Crystals prepared using this technique showed no evidence of slip. However, some of these crystals did show edge dislocation densities as high as l04 per cu cm. Some few selected crystals showed no dislocations. Single crystals of CdS were grown as large as 5 by 5 by 0.5 mm. The ampules for the growth of these crystals were 13 mm O.D., 11 mm I.D., 150 mm! LIQUIDUS SOLUBILITY MEASUREMENTS The CdS starting materials was G.E. 118-8-2 powder which was fired in H2S at 1000°C, and then a vapor transport technique5 was applied to produce a "sound" mass of CdS. The Wood&apos;s metal was prepared by weighing out bismuth, lead, tin, and cadmium in the proportions of 50, 26.5, 13.5, and 10 wt pct, respectively. The bismuth, cadmium, and lead were from the American Smelting and Refining Co. (ASARCO) and all had purities of 99.999+ pct. The tin was 99.9999 pct spectroscopic grade from the Vulcan Materials Co. The appropriate mixture was placed in a quartz tube, evacuated to a pressure of 5 X 10-6 torr, melted to a liquid, cooled to room temperature under this same vacuum. This ingot was then placed in another quartz tube, evacuated to 5 x l0-6 torr, and sealed off under vacuum. The ampule was then horizontally placed in a furnace. The temperature was raised to 600°C, and over a period of several hours the ampule was vigorously shaken several times. The ampule was then removed from the furnace, and the metallic liquid was

Jan 1, 1970

By Zara Hosseini

?Microseismicity ?Seismic Systems ?Intrinsically Safe and Explosion Proof Seismic System ?Case studies: ?Gas Drainage Optimization ?Fault Identification ?Conclusion Seismic Event ?Occurrences in which energy is released in the rockmass creating a series of seismic waves propagating throughout the rockmass ?Can cause a Fall of Ground or CoalBurst Factors creating Seismicity: ?Mining at Depth ?High stress zones ?Major geological structures ?Mining practices and strategies ?Mining activities i.e. drilling and blasting

Aug 1, 2013

By M. A. T. Cocquerel, J. G. Eacott

"Simulation techniques may be used to optimize existing processes and plant operations, and in plant design at the engineering study stage of a project . This paper describes the latter application, using a computer, to optimize the concentrate stockpile requirements of a modern copper smelter.A large open-pit mining operation is envisaged and it is assumed that copper concentrate is smelted in two flash furnaces. The proposed mining plan gives rise to metaffurgical considerations in smelting which dictate that concentrate blending is carried out in the early years of operation in order to eliminate wide variations in the grade of concentrate charged to the furnaces . Stockpiling facilities are therefore necessary for blending purposes and also to provide a strategic reserve of concentrate to ensure continuity of concentrator and smelting operations.The objective of the study is to determine the optimum size of concentrate stockpile required to take account of both metaffurgical and strategic considerations. Two separate simulation models are developed to achieve this objective. The first model is used to determine the minimum size of stockpile necessary for blending purposes to smooth out variations in concentrate grade between 15 - 60% Cu, with associated 34 6% Fe, respectively, and ensure that the concentrate fed to the furnaces does not faff below 12% Fe, which is considered a minimum for good smeltability.The second simulation model covers a projected three-year operating period and indicates the maximum size of stockpile which is likely to develop during scheduled and unscheduled shutdown periods in the concentrator and smelter.Covered storage volume and conveying facilities for the optimum size of concentrate stockpile can be designed based on the results generated by the simulation models."

Jan 1, 1980

By K. Getsos

Western Greece is a favorable site for exploration and discovery of oil fields. The most important potential source rocks seem to be all the rocks deposited before middle Jurassic under special circumstances, such as reducing conditions, which allowed preservation and maturation of the organic material. In general all the rocks of middle Jurassic to Paleogene are not favorite source rocks. The porosity type was studied on fifty samples using scanning electron microscopy (SEM). Potential reservoir rocks are the porous Paleogene wackestones-packstones with boring, channel and vuggy porosity type. Finally seal rocks are the impermeable mud-stones and wackestones of Jurassic, Cretaceous and Paleogene age. These rocks consist of micrite and whole sells of foraminiferas and the porosity type is mainly intercrystal/interparticle. A Total Organic Carbon (TOC) analysis, conducted on seventy samples using a wet oxidation method, has revealed an extremely low TOC content (less than 0.05 %). This amount is by far less than the minimum organic content amount, required for source rock characterization and characterizes all the rocks of middle Jurassic to Paleogene age. Additionally, 18O and 13C stable isotope analysis was contacted and the results are given in d values. All the rocks within the studied time interval have much lower d values than petroleum source rocks. Clay mineral content was studied in almost seventy samples. As is indicated by the clay mineral content the studied rocks have reached up to the Middle Diagenesis and the temperature during diagenesis was rather low.

Jan 1, 2006

By L. I. Gonzalez de Vallejo

SRC rockmass classification have been applied to 25 tunnels in Spain and Italy, for which it was found that much heavier supports than those estimated by the RMR index were required. SRC and RMR indices and other relevant geomechanical data were obtained during the site investigation and construction stages. Data corresponding to in situ stress measurements, analysis of tectonic structures, and instability problems arising during construction were used to asses the state of stress. The relationship between tunnel section convergence and the SRC and RMR indices was also analysed. Support measurements based on SRC and RMR classification were compared with those actually used during construction. These analyses indicate that for most of the tunnels examined, supports estimated using the SRC were much closer to those actually installed than those predicted by the RMR index. Bei der Verwendung des SRC-Systems zur Klassifizierung des Gesteins als Baugrund für 25 Tunnel in Spanien und Italien wurde festgestellt, dass viel schwerere Abstützungen benötigt wurden, als wenn die Beurteilung anhand des RMR-Systems angefertigt würde. Die Klassifizierung anhand des SRC- und des RMR-Systems, sowohl als auch andere wichtige geomechanische Daten wurden während des Ablaufs der Erkundungen und der Bauausführung gewonnen. Die Resultate der Messungen der Spannungen vor Ort, die Analyse der tektonischen Struktur und die Stabilitätsprobleme während der Bauausführung wurden dazu verwendet, um den im Felsgrund vorherrschenden Spannungszustand zu definieren. Das Verhältnis der Messungen der Tunnelkonvergenz zu dem SRC- und RMR-Index wurde auch analysiert. Die durch das SRC- und RMR-System vorhergesagte Grösse der Abstützung wurde mit der Grösse der Abstützungen verglichen, die am Bau letztlich verwandt wurden. Diese Vergleiche zeigen, dass für die meisten der studierten Tunnel die Vorhersage der Abstützungen, die anhand des SRC-Systems angefertigt wurden, viel näher der wirklich verwendeten waren als die Vorhersage anhand des RMR-Systems. SRC rockmass la classification ont été appliqué à 25 tunnels en Espagne et l&apos;Italie, pour laquelle il a été trouvé que des appuis beaucoup plus lourds que ceux évalués par l&apos;index RMR ont été exigés. SRC et des index RMR et d&apos;autres données geomechanical appropriées ont été obtenu pendant l&apos;enquête de site et les étapes(scènes) de construction. Les données correspondant aux mesures de stress(d&apos;accent) in situ, l&apos;analyse de structures tectoniques et des problèmes d&apos;instabilité surgissant pendant la construction ont été utilisées aux ânes(culs) l&apos;état de stress(d&apos;accent). Le rapport entre la convergence de section de tunnel et le SRC et les index RMR a été aussi analysé. Les mesures d&apos;appui basées sur SRC et la classification RMR ont été comparées avec ceux en réalité utilisés pendant la construction. Ces analyses indiquent que pour la plupart des tunnels examinés, les appuis évalués utilisant le SRC étaient beaucoup plus proches de ceux en réalité installés que ceux prévus par l&apos;index RMR.

Jan 1, 2003

By W. K. Katoto

The Tailings Leach Plant (TLP) of the Zambia Consolidated Copper Mines Ltd at Nchanga was commissioned in 1974 as the world&apos;s first largest successfully operated agitation leach SX-EW plant for copper production. The design, development and operation of the plant soon after commissioning termed as TLP stage II has been described by Holmes et al (1). In the initial phase the plant was designed to treat approximately 25,000 tonnes per day of current flotation tailings from the Nchanga Concentrator operations, and had a design capacity to produce 75,000 tonnes per annum of copper. Further expansion took place in 1986, and TLP stage III was successfully commissioned to treat an additional 20,000 -25,000 tonnes per day of large reserves (over 135m tonnes) of reclaimed tailings stockpiled since the early 1930&apos;s in four paddock type tailings dams (T01 to T04). The salient feature of TLP stage III expansion described by S K Mwenechanya et al (2 -3) was the installation of the world&apos;s largest Horizontal Belt Filter Plant with 26 filters each of 80 m2 filtration area.

Jan 1, 1996

By Zuoren Huang

The flowsheet of the hyd.rametallurgical zinc plant which is in use at Zhuzhou Smelters is described. The principal features of the process are fluid bed roasting, continuous calcine leaching, solution purification, zinc electrolysis, electrolyte cooling, and finally, the melting and casting of zinc forms. The Zhuzhou process for the flotation of silver from the leach residue collected on the Moor filters is described. The technical details of the process are outlined and the operating data are analyzed. The flotation facilities are described in detail and concentrate grades and recoveries are presented. The waelz process is used to concentrate In, Ge and Ga remaining in the leach residue after silver flotation. These elements subsequently are recovered by selective leaching in sulphuric acid, and details of this operation also are presented.

Jan 1, 1990

By Manuel Gomez

Bituminous coals having maximum fluidity values in the 40- to 25,400-dial-divisions-per-minute (ddpm) range were carbonized in a continuous, entrained-bed reactor. Carbonization was conducted in an 8-inch diameter, vertical reactor at temperatures from 955° to 1,345° F and at air-to-coal ratios ranging from 4.63 to 16.12 scf/lb of moisture-and ash-free coal charged. Carbonization rates from about 118 to 360 lb/hr, as-carbonized basis, were examined. It was demonstrated that carbonization temperature and air-to-coal ratio must exceed minimum values for continuous operation. Within the operating conditions discussed, highly fluid bituminous coal was carbonized to produce tar and nonagglomerated char. The yield of tar ranged from 21.3 to 38.9 gallons per ton and the char yield ranged from 1,109 to 1,563 pounds per ton, all units expressed on a moisture-and ash-free basis. It was demonstrated that the maximum fluidity and the average size of the coal along with the air-to-coal ratio and the carbonization temperature act together to influence the carbonization product yields and certain properties of the products. Prediction equations were developed from the data for product yields and selected properties of the char, tar, and gas.

Jan 1, 1968

By J F. Seale

The design of the settling pond for the Malvern Hills opencast coal project was based on a primary requirement to control runoff and sediment generated from the immediate 6 ha mine catchment, which included two seepages from old underground workings. The pond has been particularly effective in controlling turbidity in the outflow water, with the consent limit of 50 NTU being met on all but one occasion and normal levels of discharge less than 10 NTU. Water quality testing carried out at the time of consenting indicated that there were no acid-generation issues with the proposed mine site in dominant mudstone strata of the Broken River Formation, and that water from the old mine workings was near-neutral in terms of pH and well-buffered. However, it became apparent over the very dry summer of 2003 - 2004 that slaking of the exposed mudrocks in the mine batters was resulting in significant acidity generation, and outflow pH levels were well below the consent limit of 6.5 during and following periods of rainfall. Although these acidity problems have been remediated in the short-term by the use of lime products, it is clear that a programme of lithotype characterisation for AMD should have been undertaken and this has now been implemented. Design of long-term acid drainage control measures is being carried out, and will probably be based around the use of hydrated lime for pH control with enhancement of natural wetlands.

Jan 1, 2004

By S. D. Bearden

The world&apos;s barite reserve base is adequate for at least 100 years at the current consumption rate. China, India and the United States are expected to remain the leading producing countries, and the United States will continue to be the largest consumer. None of the known substitutes for barium sulfate are expected to impact existing applications. World production in 1995 was 4.41 Mt (4.86 million st), which is about 50% of capacity. Consumption is directly proportional to hydrocarbon well installation activity. Imports are expected to continue to supply more than half of the US requirements.

Jan 1, 1998

By R. Candia

The use of industrial wastes, such as quarry fines of crushed stone, should represent a basic component of sustainable development indicators. Therefore, increasing investments should be foreseen in techniques of treatment and recycling of residues in mining, as well as by-product attainment that generate jobs and income. The standards of identification and discarding of industrial wastes vary significantly between countries. However, practically all nations have started becoming more restrictive regarding environmental legislation, especially concerning production, transport, treatment, recycling and final discarding of industrial wastes. Under an environmental point of view, solid wastes produced by a system (such as a quarry) can be handled in two ways: a) they can be discarded in piles or b) they can be internally or externally recycled and reused. This second practice is translated to an additional economic consequence such as an increase of income as well as a decreased environmental impact. This option is more advanced and should be included in company policy. This paper presents cases where this practice is used, i.e. diminishing the environmental liabilities through the use of the quarry fines in the manufacture of industrial devices, incorporating such wastes in the productive chain, instead of storing them in piles.

Jan 1, 2007

By Murray Jacobson

Facts obtained by the Bureau of Mines on the dust-explosion hazard in air of materials used in the plastics industry are presented for 313 samples studied in the laboratory. Information is given on ignition temperature of dust clouds and layers, minimum explosive concentration, minimum energy required for ignition, explosion pressure and rates of pressure rise, amount of inert dust required to prevent ignition and flame propagation, and, in some instances, on the limiting oxygen concentration in an atmosphere to prevent ignition by spark and by heated surface. The effects of particle shape, additives, and resin structure on explosibility are discussed. Relative explosibility of the materials is related to the ignition sensitivity and explosion severity and is denoted by an empirical index. Recognition of the degree of hazard will facilitate adoption of adequate measures for preventing ignition and explosion during manufacturing or processing.

Jan 1, 1962