Search Documents

By E. J. Gleim

In April 1932, the Bureau of Mines published Information Circular 6595, entitled "Data in Reference to Installation of Cables in Shafts and Boreholes", in which were described methods followed in various sections of the United States when electrical circuits are taken into mines by means of cables suspended in shafts and boreholes. In view of the present tendency to extend high-tension cables along entries and passageways from the bottom of the shaft, borehole, or other point of entrance to coal mines rather than over the surface, it is deemed that the various methods of installing such cables deserve careful consideration, particularly in mines in which gas and coal dust contribute to explosion hazards. This is especially true of localities where there is an inclination to restrict the extension of 2,300- and 4,000-volt circuits into the mines. Probably it is feared that accidental contact with the cables of such circuits may result in more serious shock than with lower voltages; also, it is possible that new circuits are regarded merely as explosion hazards additional to those already existing, regardless of the manner in which the new circuits may be installed. It is the firm belief of some engineers that the circuits can be installed so that they will not be damaged by wrecks or roof falls, thereby eliminating the hazard of explosion from this source while at the same time making the chance of accidental contact remote if not impossible. Moreover, some believe that fire hazards from direct-current systems can be reduced by keeping motor-generator sets close to load centers. Thus, although the alternating-current circuits would be lengthened, the size and extent of direct-current circuits would be kept to a minimum.

Jan 1, 1939

By L. R. Burdick

The Smokescope is an instrument recently developed for determining the density of smoke by shade comparison. The instrument is designed so that the smoke is seen adjacent to two shades of gray corresponding to Nos. 2 and 3 on the Ringelmann chart. Data on smoke density are important in the smoke-abatement field. The method that is specified and accepted as standard for smoke-density determination by the majority of city smoke regulations involves comparing the smoke shade with the four shades on the Ringelmann chart as published by the Bureau of Mines.2/ This investigation was made to determine the accuracy and convenience of the Smokescope. It was conducted as a part of the Bureau I s air-pollution work, which includes the study of techniques that will promote smoke abatement. The accuracy of the Smokescope was arbitrarily defined as the difference between the Smokescope determinations and the determinations by the accepted, standard method and was expressed as Smokescope correction. Although the corrections obtained were strictly correct only for the two observers and the Smokescope of the investigation, they indicate what might be expected from any observer who uses a Smokescope with reference shades that duplicate those of the test instrument. The report is devoted largely to the data on Smokescope correction, which were taken from a single stack under controlled smoke conditions. Field work, which was done at various locations with different stacks, is mentioned briefly in connection with the comparison of the convenience of the two methods. The data for estimating Smokescope correction were taken for the three variables that were expected to affect the results, namely, the density of the smoke, the amount of light, and the color of the sky behind the smoke.

Jan 1, 1955

By Alvin Kaufman

To aid industry and Government in planning water developments the Bureau of Mines in 1963 canvassed mineral producers to determine water use in 1962. Water use by the mineral industry comprises only 2 percent of the water withdrawn by industry as a whole. The major water-using mineral industries are natural gas processing, phosphate rock, sand and gravel, and iron ore. Analysis indicated the following conclusions: 1. Total water use and new water intake is dependent on the quantity of material processed and the process water requirements of the particular industry or commodity. 2. Recirculation is dependent on the processing requirements of a particular commodity, the manner in which the water is used, cooling and condensing requirements in certain large industries, the quality of new water intake, and the need to treat new and discharged water. 3. Consumed water is dependent on the quantity of water recirculated, the temperature and humidity in the area, and the proportion of water used for cooling and condensing. 4. A threefold increase in water use by the mineral industry by 1985 is forecast.

Jan 1, 1966

By R. Noriega, M. Suazo, V. Murariu

Current AG and SAG mill circuits have continued the trend to larger, fewer mills. These large mills place a significant additional load on the discharge systems and it has become imperative that the designs of these mill discharge systems are evaluated carefully to ensure maximum efficiency and have the capacity to be able to handle the increased mill discharge volumes. The current generation of multiphysics modeling tools allow a detailed analysis of AG and SAG mill discharge performance. The combination of Discrete Element Method modeling and Computational Fluid Dynamics allows the designer to model in detail all aspects of a mill discharge performance. This includes a detailed description of the build-up of solids and slurry in a mill discharge, the recycle of material back into the mill through the grates, the relative wear rates and the occurrence of overloading at the pinch points. These tools allow intelligent decisions to be made regarding the type of discharge arrangement, pan lifter geometry, and discharge cone design, so as to ensure that the discharge is capable of handling the duties required for a specific installation. This paper details the current state of the art in these modeling tools, and provides an overview of some recent applications.

Jan 1, 2012

By A Remes, A Dennis, M Talikka, T Kotiranta, S Horn

A mine project combines vast amounts of information from various disciplines including but not limited to geology, mining, metallurgy, technology, environment and economics. In many cases, all relevant information is not fully shared between all disciplines. Thus, project performance (technical, economical and sustainability) may be evaluated on basis of insufficient information resulting in non-optimal decisions, project execution and risk management. Advances in computing power and simulation software enable various data sets to be incorporated in a single digital platform enabling more efficient and transparent data sharing. In addition, linked data sets and simulation can support assessment and optimization of the project as a whole rather than focusing on optimization of individual events. CITATION:Horn, S, Remes, A, Kotiranta, T, Talikka, M and Dennis, A, 2018. Evaluation of sustainability of copper production value chain from ore to metal using advanced simulation, in Proceedings Life-of-Mine 2018, pp 87–89 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By J. D. Miller

Contact time during bubble/particle collision is calculated by taking into considera¬tion the effect of bubble and particle motion, buoyant force, bubble size, and particle size and specific gravity density for different cases of collision. From this motion analysis approach for the prediction of contact times and from bubble attachment-time measurements,, fundamental aspects of flotation such as flotability, kinetics, and separation can be explained and are discussed with respect to the effects of bubble/particle motion, bubble size, particle size, and attachment time.

Jan 1, 1987

By David C. Oyler, Gregory Hasenfus, Gregory M. Molinda

Few studies have specifically measured and documented the large-scale loading behavior and durability of ventilation stoppings to mining induced movements, particularly from longwalls. Ventilation stoppings are more commonly the concern of ventilation engineers, and ventilation stopping response to ground movement has only been documented in an incidental manner. This paper presents the investigations of underground measurements that have been conducted to determine the loading response of stoppings constructed from lightweight aggregate concrete masonry units (CMU). These investigations have produced some interesting results that may prove beneficial, not only for developing and assessing alternative stopping construction techniques, but also for designing and selecting standard construction methods for use in varying mining conditions. For instance, the interface friction that results from wedging a CMU stopping during construction plays a substantial role in its ability to resist both lateral and vertical loads. Although they are not intended for ground support, the study showed that block stoppings can resist vertical loads of at least 2,700 to 3,000 kN. Asymmetric loading of a stopping may result in localized failure of blocks within a stopping, which, depending on the severity, can be a precursor of impending stopping failure. In addition to measurement results and implications, the paper will also present details of field measurement methods used to assess stopping response. Stopping stiffness and material strength characteristics will also be presented.

By M. Paricheh, M. Rahmanpour

"The cost efficiency and high reliability of semi-mobile or combined in-pit crushing-conveying (IPCC) and truck systems, compared to conventional truck-shovel systems alone, make them more attractive for use in modern mining operations. Semi-mobile systems, which are the most common systems in open-pit mining, combine the advantages of both systems such that fewer trucks are required, operating costs are lowered, and the operation is environmentally sound. One major aspect of utilizing this system is determining the location of the in-pit crusher and the timing of relocations. Facility location models are rarely used in the mining sector, but these models may be used for solving the in-pit crusher location problem. To this end, the main parameters affecting the IPCC location in open pit mines are reviewed and examples given of how they are applied to a dynamic location-relocation problem. Subsequently, the model is implemented for Sungun copper mine in Iran and the number and the exact time of relocations of the IPCC units determined. IntroductionNowadays, compared to the last century, metal prices are more volatile, average and cut-off grades have decreased, and stripping ratios increased. From a mining engineering point of view, many ore deposits with simple access and low capital and operating costs have been exhausted. The remaining deposits are located at depth, with no easy access, which requires high initial capital costs (Osanloo, 2012). Mining at great depths and high tonnages is possible only through open pit mining. Today, more than 80% of open pit mines in the world use a shovel-truck system for loading-hauling operations (Osanloo, 2010).With increasing depth, haulage distances increase and the number of loads per truck decreases. As a result, fuel, tyre, and depreciation costs per ton increase. Owing to these factors, open pit mining at great depth (300 to 1000 m) using shovel-truck systems faces some technical and economic problems. In-pit crushing-conveying (IPCC) systems have been known in the mining industry for many decades. The idea was introduced in 1956 in Germany. Today, the cost efficiency and high reliability of IPCC make it more appealing than conventional shovel-truck operation, especially in longer life projects with lengthy transportation distances and high production rates (Koehler, 2003). Since 1956, different aspects of this system have been reviewed by many researchers. Barua and Lanergan (1985) developed a computer program that compares the tonnage aspects of various conveyor layouts. They believed that to maximize the economic benefit of lower haulage costs associated with in-pit conveying, one must first minimize the cost of the flatter slope, which is expressed in terms of additional stripping or tied-up ore. Dos Santos and Stanisic (1987) evaluated the design of a high-angle conveyor at the Majdanpek copper mine. Then, Sturgul (1987) applied GPSS (general purpose simulation system) to find the best location of an in-pit crusher."

Jan 1, 2017

By Milton Manrique

The thermal decomposition of zircon concentrates in a non-transferred arc thermal plasma flow reactor was investigated. The plasma torch was operated using argon-helium and argon-nitrogen mixtures as plasma gases. The effect of power, feed rate and zircon particle size was studied. Products were characterized by XRD, SEM, TEM and chemical analytical techniques. The average size of the product was in the submicron range. Free energy minimization plots were used to predict the behavior of the system under different operating conditions. A kinetic model to describe the different stages of the thermal decomposition process is proposed. The results of this investigation showed a significant segregation process where the zirconia-rich product is collected in the reactor while the silica-rich product is collected in the filter. TEM analysis indicated that silica vapor is condensed on the surface of the zirconia particles.

Jan 1, 1996

By Enguang Zhu, Kangning Zhang, Yang Li

"Due to the use of outdated mining technology or room and pillar mining process in small coal mines, the coal recovery ratio is only 10% - 25%. In many regions of China: the damage area caused by the small coal mines amounted to nearly one hundred square kilometers. Therefore, special mining techniques must be taken to reclaim the wasted resource in disturbed coal areas. This paper focuses on the different mining methods by analyzing the longwall panel layout and abandoned gateroad (AG) distribution in in the abandoned area of Cui Jiazhai Coal Mine in northwestern China. On the basis of three-dimensional geological model, FLAC- 3D numerical simulation was employed. The abutment pressure distribution was simulated when the panel face passed through the disturbed areas. The proper angle of the inclined face was analyzed when the panel face passed through the abandoned gateroads. The results show that the head end of the face should be 13-20m ahead of the tail end. The pillars on both sides of abandoned gateroads had not been damaged at the same time, and no large-area stress concentration occurred above the main roof. Therefore, the coal reserves of disturbed areas can be successfully recovered by using underground longwall mining. INTRODUCTIONDuring the 70-90's, there were a lot of small coal mines in China. Due to their disordered mining, most of the small coal mines left a great many abandoned gateroads (defined as AG in this paper) and a large area of damage coal seam. In these type of coalfields, there exist many mining risk issues, including nonuniform stress in the overburden, flooding and hazardous gases accumulated in the gob. So how to lay out a longwall panel and successfully mining under this type of abandoned small mines is a big issue nowadays in China.As mentioned above, longwall panel is being performed in the damaged coal seams in order to increase recovery of coal reserves (Wang, 2009). However, the abandoned geteroads intersect to each other all around the area. So a series of production issues arose while the panel face is passing through these AG. Gang and Gong (2015) analyzed the roof stability and abutment pressure distribution during the face was passing those AG that were parallel and inclined to the faceline. Xie, et al. (2015) proposed the ground control mechanism by passing the AG in top-coal caving longwall mining. He recommended to stop the face advance until the roof is over, using high strength bolts and cable bolts, and grouting consolidation. This paper studies the different mining methods by analyzing the longwall panel layout and AG distribution in damage coal seams. Theoretical analysis and field observation were conducted to determine the overburden movement when the face was advancing under the AG. The pillar between face and parallel AG changes from elastic to plastic and eventually to the residual supporting status. All these three status was combined with the roof structure to establish the theoretical model to calculate the shield support capacity. Numerical modeling was employed to simulate the pillar stability and determine the abutment pressure distribution as the face inclined to the AG during longwall mining."

Jan 1, 2016

By Matthews SM, Gooding JE

N Longhole Open Stope at The Zinc Corporation Mine was developed in an area with large and continuous tension cracks. These cracks resulted fran widespread block subsidence into previously mined areas. The practical problems encountered and their solutions are discussed together with an outline of a new method of stope wall support using large diameter dowels installed sub-parallel to the stope wall.

Jan 1, 1985

By Gheorghe Vieru

Security and safety due to environmental impact as well as the radiological consequences during the uranium mining operations, tailings management, uranium processing, disposal of waste in conventional landfill sites are matters of great importance. The Uranium National Company (CNU) from Romania is responsible for all aspects belonging to the management of the entire Romanian uranium industry- the uranium ore extraction, transport and processing of uranium ore, concentrates processing, as well as disposal of sterile ore and waste. The paper will presents specific safety problems related to the identification and evaluation of potential environmental risks, as well as possible radiological consequences associated with the disposal of sterile and the uranium processing waste resulting from processing of the uranium ore. Computer codes will be used, such as IAEA INTERTRAN II and RADTRAN 5. It is also to be noted that this paper considers the main results of the scientific research carried out by the main author as CSI (Chief Scientific Investigator) for Romanian Research Contract on NORM concluded with IAEA Vienna.

Aug 1, 2010

By R. W. Raymond

I DESIRE to call the attention of the Institute briefly, and by no means in the way of an exhaustive description, to the interesting developments recently made on the east bank of the Hudson River, in the mining of spathic iron ores. The mines to which I refer are those of the Hudson River Spathic Iron Ore Company, situated at Oakhill on Hudson, Columbia County, N. Y., five or six miles from the city of Hudson, and opposite the town of Catskill. The ore occurs in beds, constituting apparently members of the stratified series of rocks on that side of the river, coursing nearly north and south, parallel with the river, and dipping east. The principal outcrops are presented in a range of low hills, about one mile from the river, along the crest, on the western face of which the stratum of spathic ore is more or less exposed. The length of the line in this range, along which, at various openings the ore has been discovered in profitable quantity, is about two miles. To the northward, the hills are somewhat higher, and the stratification may possibly be disturbed, though the rapid examination of the locality which I made in November last did not, include any determination of this

The leaching characteristics of a number of Australian uranium ores were determined under acid and alkaline conditions. Ores from the Ranger, Nabarlek and Koongarra deposits in the Northern Territory were readily leached in dilute sulphuric acid. Suitable processing conditions were: leaching at 35-40°C, pH 1·52·0 and redox potential -475 mV for periods of 16-24h with ore ground to 50 per cent -200 mesh CB.S.S.). Ore from the Roxby Downs deposit in South Australia required leaching at 55°C and a redox potential of -650 mV to achieve a satisfactory recovery. All ores contained refractory minerals which were not leached under conventional conditions, limiting uranium extraction to 86-96 per cent.Carbonate leaching of carnotite in calcrete ores from Yeelirrie and Lake Way in Western Australia yielded uranium extractions of at least 98 per cent. Leaching rates were considerably faster than those reported for other applications of alkaline leaching as the slow oxidation step was not required.

Jan 1, 1979

By Francisco Tapia

El presente trabajo describe la importancia de la seguridad minera a lo largo del tiempo y cuál es su visión a partir del tercer milenio. Para ello, revisa los costos y pérdidas en la minería peruana -en tanto afecta la imagen de calidad de nuestro producto por los índices de accidentabilidad que guardan, así como plantea una análisis de la efectividad de los programas de seguridad a futuro. En este sentido, el concepto de "seguridad" con visión para el tercer milenio, implica un control predictivo a los "cuasi incidentes", donde se identifique y evalúe los riesgos antes de que se origine la pérdida, así como resalta la función de la ergonomía de los factores humanos en la administración del control de pérdidas.

Oct 6, 1999

By Arthur Wade

During the year 1938, there was some drilling in Queensland, New South Wales and Victoria, as follows: Queens1and.—At Hutton Creek, lat. (approx.) 25° 45' S.; long (approx.) 149°, drilling was done by Drillers limited (subsidiary Oil Search) to a depth of 4688 ft., to the Lower Permian(?). There were small gas showings. The hole mas abandoned. At Mt. Bassett, lat (approx.) 26" 20' S.; long. (approx.) 149", Roma Blocks Oil Co. No Liability drilled to a depth of 4033 ft. The hole bottomed in granite. There were small showings of' oil and gas above bedrock in what may be Permian but is not yet determined. The company intends to run a formation tester. New South Wales.—At Kulnura, lat. (approx.) 33" S., long (approx.) 151°, the Kamilaroi Oil Company Ltd. (subsidiary of Oil Search Ltd.) drilled to a depth of 6293 ft. The Permian, probably Upper Marine Series, was reached. Drilling is to continue. Victoria.—At Romawi, lat. (approx) 37" 50' S., long. (approx.) 147" 45', a dry hole 3246 ft. deep bottomed in the Jurassic and was abandoned. It was drilled by the Governments of the Commonwealth and the State of Victoria. At Lakes Entrance, 1st. (approx.) 37" 50' S.; long. (approx) 748", a small showing of' oil (a few pints a day) was obtained from a well drilled 1275 It., to the Upper Oligocene-Glaucnnitc series, by the Austral Oil Drilling Syndicate, No Liability. Future Drilling Preparations is are being made by companies fur further test drilling in 1939, and the Governments of the Common wealth and the State of Victoria are continuing test holes for information only in the Gippsland district of Victoria. In Papua and New Guinea, no test drilling was done in 1938, but several companies are carrying on geological investigation and it is expected that, some test holes will be drilled during 1939.

Jan 1, 1939

By Michael Olmsted

Inspection of boreholes prior to blasting can result in cost reductions as well as increases in efficiency and safety. Until recently, borehole inspection was performed in two manners. For simple inspections, a flashlight was used to view the upper part of the hole. More thorough inspections were performed with long tool strings developed for oil field applications. Borehole inspection tools developed specifically for mining and blasting applications have now been developed. Video Cameras developed for borehole inspection have been in service for several years. Now measurement tools are available, developed specifically for mining.

Jan 1, 2000

By L. L. M. Kadnuck

The U. S. Bureau of Mines studied the suitability of using flexible tendon cable supports as secondary roof supports at a western coal mine. The supports were installed in longwall tailgate entries and grouted into the mine roof. This paper quantifies how the use of cable supports can improve ventilation in underground airways. A mine ventilation simulator was used to model the changes in airway resistance and airflow and show potential for further ventilation improvements when cable supports are used. Model results indicated that cable support use translated to savings in air pressure around the longwall panel and increased airflow at the longwall face.

Jan 1, 1994

By N. A. White

Whereas the ultimate world supply of energy minerals-defined as fossil fuels and fissile materials - is controlled by geological factors, the actual supply at any particular time is controlled by economic feasibility, technological innovations and /or political decisions. This paper identifies and discusses the principal uncertainties surrounding the international availability of energy minerals from now until the end of the century. A brief comparison is also made between energy and non-energy minerals. Genuine shortage s of energy minerals are now of a very long-term nature, whereas artificial ones may occur at any time and have a serious effect on the world economy due to the dependence of most OECD countries on imports of energy mineral . This paper argues that events over the last decade, such as the demand for a New International Economic Order, the OPEC increase in crude oil prices and the growing international lobby on environmental issues especially relating to nuclear safety - will progressively lead to a major, long-lasting transformation of the energy scene world wide. This transformation will encompass demand, in terms of conservation and efficiency, the supply mix of the various energy minerals , the supply system and the structure of the different energy industries . It is already affecting the role of governments and reaching into the question of national sovereignty both of developed countries, such as the U.K., Norway and Australia, and the developing countries, thereby making energy minerals a key area of international relations.

Jan 1, 1978

A three day international mining convention was held At the city hall of Nelson, B. C., June 19-21. It was held under the auspices of the Nelson-Slocan and British Columbia Mining Men's Club, the Northwest Mining Association of Spokane, the Kootenay Mine Owners' Association, assisted by the Spokane Chamber of Commerce, the Vancouver, Chamber of Mines, the City of Nelson, the Associated Boards of Trade of Eastern British Columbia and the Nelson Board of Trade. The technical program was in charge of Columbia Section, American Institute of Mining and Metallurgical Engineers and Western Branch and Kootenay-Boundary Branch, The Canadian Mining Institute. The first day was given over to the judging of mining exhibits and manufacturer's displays; the organization of a branch of the Canadian Mining Institute, and the reception of visitors from Spokane. On Friday afternoon a joint session of the Canadian Mining Institute and the American Institute of Mining and Metallurgical Engineers was held.

Jan 8, 1919