Search Documents

By Walter Miller

During no similar period in the development of petroleum refining technology has so much progress been made in methods and equipment for the economical utilization of heat. Drastically severe commercial and economical conditions controlling the refining industry during 1927 gave a great impetus to improved efficiency and more economical operation in all departments. I think it is fair to say, however, that more progress has been made in the department of heat utilization than in other branches. I use the word utilization advisedly in the dual sense of better primary generation and application of heat and of saving by recovery methods. It was because of this trend that the subject, "Economical Application of Heat," was made the keynote of the refinery engineering sessions just completed. No new, outstanding elemental discoveries can be claimed for the year along this line. Some of the progress made has been in the development of better furnaces and distilling equipment embodying the more modern principles of boiler practice in obtaining complete combustion of the fuel, low excess air requirements and high transfer rates through the heating surface. Transfer rates of 3000 to 6000 B. t. u. per sq. ft. per hr. were considered good some time ago in the older type of equipment. Today a transfer rate of 25,000 to 35,000 B. t. u. is an actual accomplishment in commercial installations and engineers are talking of the feasibility of 50,000, 75,000, even 100,000 R. t. u. per sq. ft. per hr. Contributing most to bringing this about have been the rational use of the velocity factor on both the oil and firing side of the heating surface, and the study and application of the principles of radiant heat in furnace design. Vapor Heat Economy The principle of heat exchange, especially against oil vapors, has been applied to a greater extent than ever before. The recovery of heat from oil vapors is not new. This was practiced 20 years ago or more in Europe,

Jan 1, 1928

By María Virginia Ramírez, Alejandro Alarcón, Alea Reyes

Reactive grounds (presence of FeS2, CuFeS2) can create hazards in a mine; misfires to premature deflagration or detonation of loaded blast holes. This occurs because some minerals can react to ANFObased explosives. Due to a high potential event that occurred in The Mine in 2013, The Mine and the Explosive Provider (“The Company”) are conducting a soil characterization of the areas containing reactive sulfides. This study was planned along with The Mine and it is being developed by a multidisciplinary team.

Jan 1, 2018

By A. Ignatieff

This is the first in a series of Coal Technology Reviews being prepared in accordance with a recommendation voted by the Coal Division in session at the Jubilee Meeting, Vancouver, April, 1948, that the Department of Mines and Resources be requested to arrange for publication by the proper Government authority of a Quarterly Review' of Coal Technology, for distribution among those concerned in the production and use of coal in Canada. This recommendation was subsequently endorsed both by the Council of the Institute and by the Dominion Coal Board. Further reviews (or digests) will appear at intervals in the Bulletin, or will be published and distributed by the Board which, meanwhile, has undertaken to distribute reprints of Mr. Ignatieff's review.-En. * * * The fields in coal mining technology which are considered to demand most attention and study at the present time are reviewed under the headings appearing below. Mechanization In the light of the growing shortage of skilled miners and the necessity of mitigating constantly increasing mining costs, interest continues to centre in mining methods and applications of mechanization chat will produce the maximum reduction of man power. The growth of strip or open-cut mining, also, is a consequence of this trend. Mechanization at the face attracts most attention and the trend is toward developing and adopting machines capable of cutting and loading the coal in one operation instead of having the separate operations of cutting, drilling, blasting, and loading. In Great Britain, where longwall mining is? the general practice, the A.B. Meco-Moore machine still receives much attention, and accounts describing its performance over reasonably long periods have appeared in the technical press.

Jan 1, 1948

By J. A. Brierley, C. L. Brierley

The history, current applications and future of biotechnical developments in the metals' extraction industry are reviewed. Bioleaching of copper minerals continues to be the most significant application. Uranium bioleaching was successfully demonstrated at industrial scale. Developments are now being made in biooxidative pretreatment of refractory gold concentrates, ores and low-grade materials. Advancements are forthcoming in water and solid mine waste bioreclamation, including metals' biosorption, wetland treatment of acid mine drainage, and biodegradation of cyanide in spent, heap-leach operations. Better understanding of the types and functions of microorganisms involved in metal interactions could advance genetic engineering applications in bioleaching and bioreclamation.

Jan 1, 1993

By T. R. Ley

"INTRODUCTION Brutally honest mining executives will tell you that “safety is job #1 but.. dollars are also extremely important”. When economic times are tough, as they are now in mining, it can feel like you need to choose between safety and cost control. Leading edge companies know that it is excellence at both that provides the best performance. FLUID POWER SYSTEMS Fluid power systems are ubiquitous in mining – longwall systems, continuous miners, drills, haul trucks and excavators, etc. And fluid power systems are getting more powerful and using higher pressures to move greater volumes and achieve higher productivity. Average operating pressures in mobile equipment has been rising to 450 bar (6,500 psi) over the last decade. With increased system pressure comes ever increasing levels of stored energy. Stored energy that, if released in an uncontrolled fashion, can do tremendous harm to people and things.Fluid power systems are composed of pipe, flexible hoses, pumps, valves and actuators. They are filled with fluid (mineral oil or fire-resistant) to transmit power to where it’s needed for performing work. With time and use fittings can loosen, component performance diminishes and hoses wear and tear. In hostile environments, like coal mining, hydraulic hoses can fail in as little as 2 years according to DGUV (umbrella association of German Accident Insurers), maybe sooner in some particularly challenging environments. FLUID POWER SYSTEM SAFETY While appearing simple and benign on the surface, fluid power systems, particularly such systems on mobile equipment, have many potential hazards. Hazards that most workers aren’t aware of – particularly young, new hires. And those hazards that can quickly turn deadly. During the past couple of years, including at last year’s SME Conference, I talked to a wide variety of mining people about high pressure fluid injection injuries. Some people, often with little or no field experience, never heard of it. But, people with mine operations / maintenance experience were almost always aware of such injuries.Some had even seen it happen right in front of them. But most claimed it didn’t happen all that often. It just wasn’t seen as a problem!"

Jan 1, 2016

Jan 1, 1908

By M E. Trim, J J. Johnson, W Cranston

The Brightwater conveyance system is located near Seattle, Washington in the north-western United States. The East Contract portion of the system consists of a 4.3 km long, 5.9 m diameter tunnel in soft ground and two large shafts constructed in challenging soil conditions. The two shafts are situated side-by-side in an urban valley. One will house an influent structure to direct incoming sewage and outgoing treated effluent, while the other will house a 645 megalitre per day (ML/d) influent pump station. The tunnel contains four pipelines: two force mains to convey untreated wastewater eastward from the new pump station to a new treatment plant, one gravity-pressure pipeline to convey treated effluent westward to a new outfall in Puget Sound, and one high-pressure pipeline to convey reclaimed water from the treatment plant to downstream distribution points. The shafts and the tunnel presented many design challenges. Groundwater is near the surface in the area surrounding the shafts, and compressible peat and clay soils preclude dewatering during construction. These and other challenges were encountered during design of the pump station shaft and multiple-pipe tunnel. The challenges were addressed by a design that includes a dual intersecting circular cell shaft (referred to as æthe peanutÆ) and a single tunnel into which stacked pipes will be æstuffedÆ. This paper discusses the design approach and design details for both elements.

Jan 1, 2008

By Chenggang W, Junhua D

Fragmentation variation laws in loading and non-loading areas are obtained by cement block model blasting experiments under various stemming lengths. A reasonable ratio between loading length and stemming length is worked out according to minimum average fragment size. The present continuous loading structure, for its very long length to be stemmed, leads to insufficient fragmentation in the upper part of bench. So a new loading structure with bottom air cushion is put forward. The author analyzes blasting effects and processes of two loading structures' and proves that there exists a optimal length of air cushion.\

Jan 1, 1990

For some years MINING ENGINEERING has published abstracts of the articles appearing in each issue and also of the Transactions papers published in the Quarterly. Beginning this month, a list of key words is being given with each abstract as an aid to indexing the articles for ease in retrieving them when they are needed. The value of a home or office system of indexing and retrieving technical articles is hard to over-estimate. How often is it that a technical problem comes up and someone says: "Oh yes, I've read something about that." Many hours can be expended tracing down that nebulous source. A modest indexing and retrieval system will save those tedious hours, and the person who is able to produce technical documents when they are needed will achieve an enviable status for being on the ball.

Jan 1, 1964

By S. Konetschnik, Lux Degel, R. Degel, T. Haslinger

UrbanGold and its partners from Mettop and SMS group have developed a novel technology for the recovery of valuables from all non-ferrous metals’ fractions of WEEE (Waste Electrical and Electronic Equipment), with a special focus on low qualities which are commonly landfilled or incinerated. The technology is marketed under the brand name “UrbanGold Flex” to illustrate the high flexibility in respect of plant design and raw material portfolio, allowing also the processing of low grade material and materials with high caloric values. The process of the technology’s centrepiece, a modified and enhanced bath smelting furnace called “HENRI”, was investigated in numerous pyrometallurgical trials as basis for a scale-up towards a capacity of up to 100,000 tons of WEEE-concentrates per year. All relevant facility components have been evaluated in respect of references, fall-back options, as well as exit strategies (alternatives) to minimize risks when establishing a novel technology. A spin-off within the development is the “UrbanGold Compact” technology which can be seen as optimization of state-of-the-art smelters by using an optimized TBRC as primary processing unit. As an UrbanGold Compact plant will be the first industrial scale reference of UrbanGold’s technologies, it is also explained in the publication. As precious metals recovery is of major (economical) importance when recycling WEEE, major attention has been given to minimize the losses of these valuables. These measures, as well as a sophisticated way of utilizing waste heat as far as possible, result in interesting business cases with gross profits of up to 20% or even more. INTRODUCTION Over the past years, the demand of electrical and electronic equipment has increased dramatically with technological progress. Innovations on the technology of electronic devices led to a shorter usage and lifespan and thus boosted the generation of Waste Electrical and Electronic Equipment (WEEE). WEEE is one of the fastest growing waste streams, growing at 3 to 4% per year worldwide and is expected to reach more than 52 million tons per year by 2021. Currently, about 45 Mt of these wastes are estimated to arise worldwide, and the trend is rising (Baldé et al., 2017).

Jan 1, 2019

Jan 1, 1931

By Patrick R. Taylor

A kinetic study of the fluosilicic acid leaching of galena was performed under the presence of different oxidants. Fluosilicic acid concentration, agitation speed, concentration of solids and particle size, type and concentration of oxidant, and temperature were the variables studied. Hydrogen peroxide was found to be the most effective oxidant, its effectiveness being proportional to its concentration. As expected, an increase of leaching temperature increased the overall extraction and extraction rate. The same was found by decreasing the galena particle size. It is thought that leaching using hydrogen peroxide is controlled by fluid film mass transfer due to the calculated apparent activation energy. Reaction by-products such as sulfur and sulfur compounds retard the leaching rate. A mathematical model is proposed and compared to experimental results.

Jan 1, 2003

By W. C. Winegard, W. J. Bratina

Internal friction characteristics and temperature dependence of the torsion modulus for iodide zirconium containing 2.4 pct Hf were investigated, using a low frequency pendulum technique. The internal friction curve consists of a background which increases as the temperature increases, a maximum at 860°C apparently a background due to the al-lotropic transformation, a maximum due to grain boundary relaxation with an associated heat of activation of 58,000 cal per mol, and an anomaly below 350°C which may be associated with a precipitation perphenomenon, Oxygen in below small amounts reduces the grain boundary maximum substantially. The variation of the torsion modulus at 20°C was found to be 3450 Kg per mm2 for the zirconium used in the present work. IT is well known that small amounts of certain solutes materially affect the ductility of zirconium. Lely and Hamburger,&apos; as early as 1914, found that high purity zirconium exhibited a remarkable ductility, while Fast&apos; has shown that oxygen and nitrogen can cause substantia1 embrittlement. Treco" has recently demonstrated that the ductility decreases sharply with the oxygen content, and that 2 atomic pct O2 embrittles zirconium to such an extent that cold working is impossible. The marked decrease in ductility is difficult to understand in view of the fact that Domagala and McPherson4 report the solid solubility of oxygen in zirconium to be 29 atomic pct at 500 °C. Another metal which behaves much the same as zirconium in this respect is titanium. Pratt et al." investigated the internal friction characteristics of titanium and the effect of oxygen on the internal friction values. It is evident that internal friction measurements are of value for studying grain boundary segregation, as shown by Pratt et al. for oxygen in titanium, by Pearson for oxygen in copper, and by Maringer and Schwope for oxygen in molybdenum. With this in view, the internal friction characteristics of zirconium and the qualitative effect of oxygen on the grain boundary relaxation phenomenon were investigated. Materials and Experimental Procedure The zirconium used in the present work was supplied by the Foote Mineral Co. in the form of wire 0.05 in. diam. The analysis supplied by the manufacturer indicates the amount of hafnium as 2.4 pct, less than 0.01 pct O less than 0.01 pct N,, less than 0.02 pct H,, and less than 0.001 pct C. Additional spectro-graphic analysis indicates the other main impurities as follows: 0.01 pct Fe, 0.05 pct Si, 0.008 pct Cu, <0.005 pct W, <0.001 pct Al, <0.05 pct Mg, <0.001 pct Ni, <0.02 pct Ca, and <0.01 pct Ti. Microscopic examination of the material in the as received condition revealed very fine grains with numerous twins. Specimens were annealed either in situ in the internal friction apparatus or in evacuated silica tubes in an auxiliary furnace. When the specimens were annealed in the auxiliary furnace, they were wrapped in identical zirconium wire to prevent contamination by the container. Metallographic sections were taken in all cases. Some were taken from the specimens used for internal friction measurements after completion of the experiments, while others were taken from control specimens at intermediate stages of the experiments. lnternal friction values were obtained by measuring the free decay of a low frequency torsion pendulum (1 cycle per sec), the suspension of which was

Jan 1, 1957

By F. D. Mahone

Much crude oil, as produced from the well, carries varying amounts of water, which may be present as free water in globules sufficiently large to settle out, in time, if the fluid is allowed to stand, or as an emulsion formed by myriads of minute water particles, each surrounded and entrapped by a film of oil through which it cannot break under the action of gravity alone. Such an emulsified mixture of oil and water is commonly termed "cut oil." When such an emulsion is subjected, under proper conditions, to the influence of a high-potential alternating-current field, the minute water particles rupture the enveloping oil films and coalesce into larger water droplets this procedure continuing until all the water is freed into drops of such size that they readily settle out. This action has been photographed by the micro-moving-picture camera; under the microscope, the breaking-up of the emulsion, as described, is seen to be accomplished in a few seconds. The low power requirements of the process, from records of commercial plants, substantiate the theory that the action is that of a multitude of electrical condensers in series, rather than that of a number of conducting paths. The minute water particles serve as the metallic elements, or plates, of the condensers and the separating oil acts as the dielectric. Such surface charges as the particles may have are removed, and the intervening oil is broken, probably electrically by the voltage and mechanically by the attractive force between adjacent oppositely electrified particles. The principle of breaking up an emulsion under the influence of an alternating electric field was discovered by F. G. Cottrell and Buckner Speed, through experiments conducted, at the University of California, which resulted in a plant being installed on the property of the Lucile Oil Co. in the Coalinga field, California, early in 1909. This plant was able to reduce 14-per cent. emulsion to less than Pper cent. with commercial success. Standard Cottrell Apparatus The present standard Cottrell apparatus consists essentially of the electric treater and a settling or trap tank. The treater is a galvanized-iron tank approximately 3 ft. in diameter and 10 ft. high, which con-

Jan 1, 1924

By M. R. Henzen, J. W. Funke, G. J. Stander

SYNOPSIS The adverse effect of acidic mine drainage derived from gold and coal mining operations on the quality of receiving waters is described, together with measures to be taken to counteract this pollution. The mineral load and the toxic effects from metallurgical and metal finishing industries are also considered. Attention is drawn to water conservation aspects.

By M. G. Magnuson, H. O. Hofman

When dry chlorine gas is made to act in the cold upon fiuely-divided gold,&apos; it converts the latter with evolution of heat into auro-auric chloride, Au4 Cl4, a hard, dark-red, hygroscopic salt. Moisture splits this salt into aurous and auric chloride, Au²C14 = AuCl + AuCl³; treatment with water converts it into auric chloride and gold, 3 Au²CI4 = 4 AuC1³ + Au². Aurous chloride, when stirred with water, undergoes a similar decomposition, 3 AuCl = AuCI, + Au,. These decompositions of auro-auric chloride and of aurons chloride furnish the explanation for the practice of moistening an ore before it is treated by the Plattner chlorination-process; practical experience having shown that gaseous chlorine gave an unsatisfactory extraction with dry ore. According to Rose12 fine gold is acted upon more slowly by chlorine than gold containing some base metal, e.g., copper. He also says that small quantities of silver increase the rate of solution, but adds that the coating of silver chloride formed, checks, and finally stops, further action, if the percentage of Silver be increased beyond a certain undetermined amount. Bromine3 acts upon finely-divided gold in a manuer similar to chlorine; the auro-auric bromide, Au²,Br4,, however, is not hygroscopic. Upon treatment with water it is decomposed as is the corresponding chlorine salt. It is generally believed that bromine does not act as energetically upon gold as does chlorine. This seems to be borne out by the results in the leach- +1MASSACHUSETTS INSTITUTE OF TECHNOLOGY, BOSTON, MASS.

Jan 1, 1905

The Institute was founded in 1894 as the Chemical and Metallurgical Society of South Africa. In 1904 it was reconstituted as the Chemical Metallurgical and Mining Society of South Africa and in 1956 it became the South African Institute of Mining and Metallurgy. The objects of the Institute are to advance the science and practice of mining and metallurgy, to afford opportunities for the interchange and recording of knowledge of mining and metallurgy and to ensure high standards of professional conduct and competence. Membership benefits include monthly issues of the Journal of the Institute, monthly General Meetings at which papers are read, symposia, excursions to mining and industrial concerns and the use of club facilities at Kelvin House. Technical journals received on an exchange basis are available to members at the Johannesburg Public Library. The current membership of the Institute is over 1,600. Membership applications are accepted from suitably qualified persons and the requirements for entrance to the various grades of membership are summarised below. Fellows shall not be less than 30 years of age, shall be university graduates in pure or applied science or shall produce evidence to the satisfaction of the Council that they have successfully completed a co-ordinated course of study in pure or applied science of at least three years&apos; duration at an approved university or institution deemed by the Council to be of equivalent status. Members shall have been employed in senior technical positions in important mining or metallurgical undertakings for at least five years or they shall have practised as mining or metallurgical consultants for at least five years. They shall be practising their profession at the time of application. Entrance fee R10.00, Annual subscription R17.00. Letters of designation: F.S.A.I.M.M. Members shall be not less than 25 years of age and shall be university graduates in pure or applied science, or shall have successfully completed co-ordinated courses of study in pure or applied science of at least three years&apos; duration. They shall have been engaged in work of an approved technical character in the mining or metallurgical industries, of which not less than two years shall have been in positions of responsibility. A candidate shall be practising his profession at the time of his application. Entrance fee R8.00, Annual subscription R15.00. Letters of designation: M.S.A.I.M.M. Associates shall be not less than twenty-five years of age, and shall have been engaged in positions of responsibility in, or associated with, the mining or metallurgical industries for periods of not less than three years. If, however, the candidate for admission to the higher grade of Associate, is at the time of his application, already a Student, he need satisfy the Council only that he is, at the time of his application, engaged in a position of responsibility in or associated with the mining or metallurgical industries. In all cases the applicants shall satisfy the Council that they are fit and proper persons to become Associates. Entrance fee R8.00, Annual subscription R15.00. Graduates shall be not less than 21 years of age and shall be university graduates in pure or applied science, or have completed co-ordinated courses of study in pure or applied science of at least three years&apos; duration at an approved university or institution. They shall not remain Graduate members after attaining the age of 30 years without the permission of Council. Entrance fee R2.00, Annual subscription R10.00. Students shall be persons not less than 18 years of age who are being educated or trained in a manner approved by the Council, to occupy a technical position in or associated with the mining or metallurgical industries and who, furthermore, shall not have attained the qualification required for a higher grade of membership. They may remain Students until they have obtained the necessary qualifications for transfer to a higher grade of membership, but not after the end of the Institute&apos;s financial year in which they attain the age of 28 (twenty-eight) years. They shall then transfer to a higher grade to retain membership of the Institute. The Council may relax the provisions of this clause in such cases as it considers appropriate. Entrance fee nil; Annual subscription R3.00. Other. The Council has the power to elect to the grade of Fellow or Member, candidates who may not fulfil all the requirements for entrance to these grades but whose status, professional achievements and practical experience in mining or metallurgy justify such election. Applications. Requests for membership application forms should be addressed on the attached form to the Secretary, South African Institute of Mining and Metallurgy, P.O. Box 61019, Marshalltown, Transvaal.

By Arthur Knapp

OIL-WELL depletion curves, to be of value, should show when a well or lease may no longer be operated at a profit. The difference, at any time, between the total expenditures and the total income of a lease or well may be called the lease status. Plotting this lease status against time will give a curve subject to more accurate and different interpretations than the barrels-time curves. According to the hypothetical barrels-time curves shown in Fig. 1, well A, at the end of 16 mo., is producing twice as much oil as well B and will continue to produce for another year whereas well B will cease producing in about 6 months. DATA FOR LEASE STATUS-TIME OR DOLLARS-TIME CURVE TIME LEASE MONTHS STATUS Lease purchased for $3000 0 -$ 3,000 No expenses chargeable to lease for 3 mo 2 - 3,000 Well A is started; cost of drilling for month is $16,000 3 - 19,000 Well is completed at additional cost of $10,000 4 - 29,000 Well A is brought in and flows 10,000 bbl. first month (see Fig. 1). Necessary to invest in tanks, boilers, pipe lines, etc.: difference between expenditures and receipts gives profit for month of $5,000 5 - 24,000 Investment is small, cost of operating well A is small, so profits are $15,000 6 - 9,000 Well ceases to flow so there is additional investment for pumping equipment and additional operating expense; net earnings from 6,000 bbl. of oil produced is $4,000.... 7 - 5,000 Lease operation now becomes normal and curve becomes smooth 8 - 500 9 2,000 10 4,500 11 6,000 12 7,700 13 8,700 14 9,000 15 9,500 16 10,000

Jan 1, 1921

By M. A. Dayananda, R. E. Grace

Vapor-solid diffusion couples were employed in a study of ternary diffusion in the single-phase copper-rich corner of the Cu-Zn-Mn system Interdiffusion coefficients were measured at three different compositions corresponding to the intersections of diffusion paths determined at 850°C. Intrinsic diffusion coefficients were determined at two compositions by the Philibert-Guy method. New relations between the various intrinsic diffusion coefficients are also presented. MOST of the investigations of ternary diffusion have been made with "sandwich" couples formed by welding together two homogeneous solid solutions with or without markers placed at the interface. With such couples Kirkaldy and his coworkers1,2 have determined interdiffusion coefficients which describe ternary diffusion in the substitutional alloy systems, Cu-Mn-A1 and Zn-Cu-Al. Guy and Leroy3 have reported intrinsic diffusion coefficients for Co-Ni-Cr alloys as a function of composition using the analysis of Philibert and Guy.4 The use of semi-infinite diffusion couples, for example, vapor-solid couples, where the diffusing species are supplied from a vapor source in contact with a diffusion disk, has so far been confined to studies of binary diffusion. Balluffi et a1.5,6 have successfully determined the interdiffusion as well as the intrinsic diffusion coefficients in several binary metallic systems employing vapor-solid couples with markers initially placed at the vapor-solid interface. They have also discussed the general advantages and limitations of such couples. Vapor-solid diffusion couples can successfully be employed in ternary diffusion studies. The importance of such couples in ternary diffusion lies in the fact that inert markers lie close to the vapor-solid interface, and the composition of the marker plane is virtually known before experimentation begins. Another minor advantage is that the method of Philibert and Guy4 may be used with three alloys instead of four. Lastly, the diffusion paths need not be S-shaped, as pointed out by Meijering7 for "sandwich" couples. The Cu-Zn-Mn system is convenient for ternary diffusion studies because of the large single-phase field in the copper-rich corner. The vapor pressure of zinc above such alloys is known, and X-ray measurements indicate that the molar volume is nearly constant over a wide range of compositions.8,9 It is the purpose of this paper a) to extend the analysis of Balluffi and seigle5 to permit an evaluation of interdiffusion coefficients in ternary vapor-solid couples, b) to use the method of Philibert and Guy to determine intrinsic diffusion coefficients with such couples, and c) to present experimental data on both interdiffusion and intrinsic diffusion coefficients for the Cu-Zn-Mn system at 850°C. INTERDIFFUSION IN TERNARY VAPOR-SOLID COUPLES The analysis of Balluffi and seigle5 is extended in this section to a vapor-solid couple where two solutes diffuse from a vapor source into a ternary solid solution. To take into account the expansion of the diffusion disk caused by the absorption of mass from the vapor phase, the total fluxes are expressed on the basis of a coordinate system that moves with the velocity of the vapor-solid interface; thus. where D3ij are the intrinsic diffusion coefficients,4 v(x, t) is the local Kirkendall velocity of mass flow, and F(t) is the negative velocity of the vapor-solid interface (x = 0). Both these velocities are based on a fixed coordinate system far removed from the diffusion zone. Using the continuity relations and Darken&apos;s method1&apos; for a ternary system in which components 1 and 2 diffuse from the vapor phase into a solid of negligible vapor pressure, one obtains

Jan 1, 1965

Comparatively recent Tasmanian legisla tion established a series of rigid control standards for environmental protection just as ma spectacular expansion of the mining industry was nearing completion. Upgrading existing protection to obtain the necessary licence to operate under these new regulations required further major works and involved a considerable outlay of non- productive capital at a time when escalating costs and falling metal prices were straining economic efficiencies to the limit. Late in 1974 a major environmental protection scheme was commissioned by the Electrolytic Zinc Company of Australasia Limited at Rosebery on the West Coast of Tasmania. This 4 million dollar project was specifically developed by the Company ahead of and to meet the new standards for control of total effluents discharged from its zinc-lead -copper-pyrites mine and concentrator.

Jan 1, 1977