Search Documents

By D. Lee Petersen, Travis Davidsavor

The 2003-2004 expansion of a Duluth medical center required rock blasting adjacent to the existing structures, a Mn/DOT retaining wall and other urban structures. This case history describes the methods of a blast damage assessment, based on blast parameters, excavation locations, and critical vibration receptors (including surgical suites, a linear accelerator and a major retaining wall). The assessment concluded that blast vibrations could be controlled, by limiting charge weight, to eliminate impact at the critical receptors. Prior to construction, we conducted preconstruction surveys on structures susceptible to vibration damage. During construction, we reviewed submittals, observed test blasts, reviewed blasting logs and monitored blasting vibrations. Up to 13 seismographs were used simultaneously. Close coordination with medical center operations personnel was necessary to prevent impacts to critical medical procedures. Measured vibrations were clustered around the predicted values, and attenuated at the predicted rate. High-frequency blast induced ground vibrations induced low-frequency vibration of an adjacent MnDOT retaining wall. Medical center structures were observed to significantly attenuate the ground-borne vibrations. This paper was first published in the Proceedings of the 56th Annual Geotechnical Engineering Conference, 2008, at the University of Minnesota.

Jan 1, 2010

By P. Groleau, O. Tavchandjian, D. Marcotte

In open pit mining, each small mining unit (SMU) is selected for mill processing based on an estimate of its true grade. The estimation is usually done using analyses of cuttings from blast holes within that SMU. One common estimator used for selection is the arithmetic average of within-SMU samples. This estimator is conditionally biased. The effect of a conditional bias is to overestimate the profit really recovered from the deposit. For this reason, a conditionally unbiased estimator is preferable. Increasing the number of samples generally improves the accuracy of the estimation (and diminishes the conditional bias, if present, of most estimators). However, there exists a practical limit where an additional sample does not improve the estimation sufficiently to cover the expense of making the analysis. This limit is specific to each deposit and depends on geostatistical parameters, economic factors, and mining parameters. This study examines how the number of samples affects the recovered reserves and the resulting profit. Also, the effects on optimal profit of varying the different factors are examined. Globally, the number of samples required increases with the selectivity of the operation. For a given ore deposit, the greater the number of SMUs selected for processing, the fewer samples are required and vice-versa.

Jan 1, 1998

The formation and distribution of gold placers in active collisional mountain belts are directly related to the tectonic, topographic, climatic and erosional constraints prevailing on either side of the orogen at the time of placer formation. In the absence of pre-existing placer deposits, these factors combine to concentrate placer development on the side of the orogen facing the prevailing winds, where most of the erosion and uplift occurs. Drainage network changes and glaciation can significantly alter placer distribution with respect to source areas within the orogen. After collision stops, placer formation will proceed on both sides of the orogen as exhumation of the mountain belt ensues. Incorporation of pre-existing placers formed on ancient mountain belts into younger placers in subsequent orogens, may be recognised by anomalous placer distribution compared to the above model. Most of the relatively young giant placers such as those inNew Zealand, Chile, Bolivia and Columbia, exhibit these general patterns. Their character and mode of formation have important implications for the formation and distribution of much older placers, such as those in South Africa's Witwatersrand Basin.

Jan 1, 1996

Underground excavations are subjected to complex stress changes caused by nearby mining, but may also be affected by repeated dynamic loading from blasting and seismic events. In some cases, the combined, cumulative effects can lead to unforeseen damage, displacement and instability. Simulating dynamic loading of an underground excavation is a very complex task. The state of rock mass stress, damage and deformation must first be simulated sufficiently requiring small-scale structures to be explicitly modelled. Supporting elements must be represented with high similitude and then the dynamic event must be applied to the system in the case of blasts, or evolve as a consequence of rock mass instability for seismic events. A special case is for the effect of pit blasting on underground excavations - discontinuous rock phenomena at scales from mine, to bench, to pillar, to tunnel need to be captured and this represents one of the most computationally intensive tasks in mine simulation. Recent advances in computer power allow these tasks to be completed at a mine scale, incorporating discontinuities and geological detail matching the best practice for static Finite Element analyses. The results are a worthwhile contribution to mine decision-making, but require careful interpretation and thoughtful inputs - even more so than quasi-static analysis - as the cumulative effects of unfavourable modeling practices are greater. Some learnings from experiences with mine scale, discontinuum dynamic simulation are summarised, including a discussion of considerations of scale and similitude for this type of analysis.

Nov 25, 2010

The JORC Code contains a mandatory classification system for Mineral Resource and Ore Reserve estimates for public reporting. The classification is a statement of the Competent PersonÆs confidence in the estimate and an attempt to convey that confidence to the various users of the resource estimate. In general the classification process is either largely subjective, relying on the Competent PersonÆs experience, or relies on statistical measures derived from the estimation process, or is derived from an estimated level of confidence in the outcome. However, the statistical measures may not necessarily relate to the overall confidence in the resource or reserve which must take account of the confidence in the geological inputs to the estimation.In addition to the traditional deterministic interpretation and estimations adopted by geologists, semi-quantitative techniques are now available to improve the estimation of confidence while continuing to involve the Competent PersonÆs experience in the process. Methods for quantifying confidence in mineral resource estimates for advanced projects and operating mines have also been developed.Classification is undertaken primarily as a communication tool between the estimators and the other stakeholders in the process. A brief examination of the stakeholdersÆ requirements is included.

Sep 26, 2011

By Andreas Orth

Outokumpu Lurgi Metallurgie has developed a process for the calcination and reduction of laterite nickel ore tines where the reduction of iron and nickel to the wustite/metallic states respectively, is performed in a fluidized bed reactor using reduction gas generated very cost effectively from natural gas in an autothermal catalytic reactor. As an option coal can be used as reductant as well as additional fuel. The process of reduction and calcination is very energy optimized. It uses the off gas from the fluidized bed reduction reactor, which still contains energy, to dry and calcine the nickel ore fines in a primary stage circulating fluidized bed (CFB) reactor. The product shows high metallisation of nickel and iron oxides reduced to the wustite stage. This results in considerable energy savings in smelting the prereduced product to ferro-nickel. Alternatively the product can be leached to produce nickel. Laboratory tests showed very high recovery of nickel and cobalt. Keywords: Fluidized Bed, Prereduction, Calcination, Ferro-Nickel

Jan 1, 2004

By E. A. Beck

(New York Meeting. February, 1913.) For a number of years many attempts have been made to use thermit in order to do away with piping in ingots. Some of these attempts were successful, while others did not give the expected results. Nearly every plant had its own method of using the thermit, and no special care was taken to study, the results or to find the causes for lack of success. Formerly the principle of the process was to decrease the piping by introducing a can filled with thermit, attached to an iron rod, into the head of the ingot directly after it bad been poured. In this case the thermit reaction took place in the upper part of the ingot, and it was thought that through the heat produced the head would keep liquid longer and piping thus be reduced. In other words, the aim was to keep the head of the ingot open by making use of the heat of the thermit reaction, which would thereby give the gases in the steel sufficient time to escape. This result can be attained by the application of a large enough quantity of thermit, but it would not be economical in general practice, and could only be used for high-grade material. Many steel-makers abroad and in this country have had this experience. The Th. Goldschmidt A. G., Germany, has, therefore, made a special study of this question with the co-operation of a well-known steel company, and has worked out a new method for. the application of thermit for this purpose. The results obtained have been most satisfactory and reliable, and this- process is now used in Germany on a large scale in many prominent steel-works.

Jan 4, 1913

By J. N. Van der Merwe, M. Mathey

"The development and mechanical characterization of coal-crete, a composite material generated from coal fragments and some binder material, is described in this paper. Coal debris was obtained from a colliery in South Africa. The binder used in the study basically consists of cement and water, and further ingredients are added to the mixtures, such as sand, fly ash and polymers, in order to investigate alterations of the mechanical properties of coal-crete.Results from over 220 mechanical tests on coal-cretes with various binder mixtures give consistent trends for the material’s behaviour. Linear relationships are suggested between the uniaxial compressive strength, Young’s Modulus and the indirect tensile strength of the coal-crete.It is shown that mechanical properties comparable to coal can be achieved. Coal-crete is therefore suitable for physical modelling of mining situations in experimental studies and for use as backfill in underground coal mines. The latter application is particularly attractive when refuse coal is used as aggregate material. The indicated trends in this study may be used as a guideline for individual coal-crete design needs. However, some uncertainty remains as to the influence of particle shape, size and gradation, coal rank and age of the coal-crete. These aspects are recommended for further research."

Jan 1, 2015

By Maria Thornhill, Rolf Arne Kleiv

INTRODUCTION The last decade has given rise to an increasing number of deep-sea mining concepts (DSMCs) outlining technical solutions for the production chain from seafloor mining to mineral or metal extraction. The vast technological and logistical challenges coupled with immature but rapidly evolving technology has spawned a great variety in proposed concepts, and the exact implications of the phrase ‘best available technology’ is very much an open question. DSMCs differ significantly with respect to choice of technology, technological readiness level, degree of resource utilization, logistics, OPEX and CAPEX requirements, overall profitability, legal and political implications, not to mention environmental impact. Hence, a system for classifying concepts could provide a useful identification and structuring tool when performing economic, judicial or environmental assessments of DSMCs, as well as offering a general terminology to describe concepts sharing fundamental traits. This abstract proposes a DSMC classification system based on how a concept makes use of mineral separation at the different stages in the ore’s journey from the deposit to the ocean surface and ultimately to onshore facilities. Mineral separation, as a process step, is the key factor in determining both the state and mass flow of materials along the production chain and has, as such, a decisive effect on economy and environmental impact of any deep-sea mining project. A DSMC that is based on bringing the entire volume of broken ore to onshore facilities for processing will look very different from a concept based on pre-concentration (i.e. mineral separation) at the seafloor. Whereas the latter offers savings in the form of reduced energy cost for vertical transport, it also represents a substantial additional technological challenge. Furthermore, whether or not a concept relies on mineral processing at the seafloor or on a floating facility at the ocean surface above the deposit also determines the point at which mineral separation waste (i.e. tailings) must be managed. Different concepts offer different opportunities for tailings deposition, and are at the same time bound by different requirements.

Jan 1, 2018

By D. Papacharalampos

A combination of decision- theoretic and knowledge-based methods can be used to classify rock-types from satellite data both efficiently and accurately. An expert system utilizes knowledge-based rules, as a field geologist does, to produce results that make geological sense. Our expert system (GEMS), first processes background information from preexisting knowledge and develops a plan, then classifies individual pixels, and finally generalizes the results using geological rules and plots a map. The system is implemented on a microcomputer and is inexpensive enough to be a part of the standard equipment of any geologist who prepares reconnaissance maps.

Jan 1, 1986

By Hideki Yamamoto, Junji Shibata

"The chemical reactions of fluoride and chloride gases with metal chloride or metal oxide are utilized as an effective treatment for harmless disposal. These chemical reactions can be adopted in the temperature range of 80°C~400°C, which is lower than that in the combustion treatment (800°C). Reaction products are metal fluoride or metal chloride which are a harmless and a valuable chemical material as one of new resources. This paper, concerns with a new harmless disposal treatment of toxic global warming gases.IntroductionNew technology to make fluoride and chloride gases such as NF3, CF4, SF6 BF3, Cl2 and BCl3 harmless has been developed and a new concept on the removing toxic gas to be used in the advanced process of materials has been established. The fluoride gases ~re toxic and special type of gases to be used in the process of manufacturing semiconductors and their specific applications include the dry etching of semiconductors, cleaning of CVD systems, an oxidation agent for rocket fuel etc. Especially, NF3 is also attracting an attention as a high-energy source for chemical laser systems. As a fluoride gas like NF3 is, however; toxic and highly stable chemically, if discharged into the atmosphere, it is liable to cause far-reaching adverse influences on global warming in the same manner as carbon dioxide gas and feron gas.Up till now, the combustion treatment method has been adopted for the disposal of the gas, and when treating the gas by high-temperature combustion (800""C), the generation of nitrogen oxides (NOx), sulfur oxides (SOx) and hydrogen fluoride (HF) have been confirmed: These chemical substances are not only linked with an intense c0rrosion of the combustion systems but also create the generation of atmospheric pollution and acid rains, and therefore, constitute a serious social issue."

Jan 1, 2000

By George Burnhart

"Sonic drilling is a relatively new technology even though it has been in development since the late 1940s. It was initially funded by the U.S. petroleum industry and then, in the late 40s, Russian scientists worked on developing sonic drilling, their interest based on drilling rates 3 to 20 times that of conventional methods. In the early 1960s, the Shell Oil Company backed research that resulted in a down-hole device with a series of eccentric weights driven by drilling fluid to generate vibration. Hawker Sidley, in the early 1980s, developed the first modern prototype sonic drills in Vancouver B.C. and the North Star Drilling Company in Minnesota became the first contractor in the U.S. to operate sonic equipment in 1985. In 1994, North Star became a division of Boart Longyear, headquartered in Salt Lake City, Utah.What’s Unique about a Sonic DrillA sonic drill rig appears and operates very much like any conventional top-drive rotary rig. The key difference is that a sonic drill has a specially designed hydraulically powered drill head, containing oscillators, that generates adjustable high-frequency vibratory forces. The sonic head is attached directly to the drill pipe or outer casing, sending the high frequency vibrations down through the drill steel to the face of the drill bit. This creates displacement, fracturing or shearing action depending on the material being drilled. The oscillator uses two eccentric, counter-rotating balance weights or rollers that are timed to direct 100% of the vibration at 0 degrees and 180 degrees. An air spring houses the oscillators and separates the vibration from the drill rig itself. The vibratory frequency is controlled to suit operating conditions and to achieve optimum drilling rates.When the vibrations coincide with the natural resonant frequency of the steel drill rod or casing, a natural phenomenon called “resonance” occurs. It allows the rig to transfer timed vibratory energy into the top of the drill string, utilizing the natural stored energy of the steel. This causes the drill string to use inertia and act like a flywheel delivering tremendous amounts of energy directly to the bit face. In friendly overburden formations, a sonic drill rig can achieve penetration rates of one ft per second."

Jan 1, 2008

By George T. Faust, S. R. B. Cooke

"The Southern Experiment Station of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama, is investigating the preparation of pulverized coal for fuel. In this study the relative amount of surface in various products and samples had to be assessed. Because of the familiarity with screens and because of the simplicity of using the inverse ratio of the opening for ascertaining the amount of relative surface in the respective sizes, screens down to and including 270-mesh were used. This choice was made in full cognizance of the irregularity of screens, but it seemed that if the same screens were used throughout all the tests the relative values would be satisfactory.In dealing with the subsieve sizes, pneumatic elutriation was used to make several fractions to extend the sizing analysis into the range of hypothetical screens. This kind of a sizing analysis was thought necessary because it is familiar to all operators, and, furthermore, it is amenable to several ways of plotting curves that bring out the characteristics of various coals and various methods of grinding.The method of obtaining the data from which to set up the hypothetical screen scale is the subject of this paper. It consists in determining the average projected area of the particles in the respective elutriated products. By extending the ""area method"" to sieve sizes, a factor is found that may be applied to the subsieve sizes, and thus the scale is projected in a regular manner. This method avoids contentions about specific surface and steers clear of ""average diameter"" except as material sized on screens may be said to have an average diameter."

Aug 1, 1939

By G. Chahal, L. C. So, S. Faucher, S. Mostaghel, S. -Y. Oh, S. K. Lee

Slag dumping and water granulation are the most commonly used slag treatment methods in the metallurgical industries. In both processes, water is present (by desire for cooling and dispersion or as a result of rain accumulation) and thus equipment and operations are designed to minimize and mitigate the risk of steam explosions resulting from the inappropriate contact of slag with water. Slag handling practices have, therefore, never been inherently safe; even good design, operation, and maintenance are not sufficient to prevent explosions or other related injuries from occurring. For slag handling to become inherently safe, our industry must eliminate the potential contact of water with molten slag. This is today feasible with the advent of dry granulation technologies, a review of which is presented, and it thus falls to us, in the metallurgical sector, to lead the way in their final stages of development and adoption. Furthermore, while slag dumping and water granulation offer some metallurgists the means of valorizing their slag as a by-product, for most, this is not the case. The energy in slag is lost through dumping and water granulation processes, and where slag is sold as a by-product, it is for its chemical content only. Here, dry granulation processes also offer advantages including the production of by-products which hold value in both their chemical content and physical properties and heat recovery. Dry granulation, therefore, augments the methods by which slag may be valorized over traditional processing methods.

Jan 1, 2015

By J. M. Mitchell

Kuala Lumpur, Malaysia is underlain by karstic limestone. Firm clays, mudstones and siltstoncs of the Kenny Hill Formation overlie the limestone for about two thirds of the city. The remaining third has deep deposits of very soft alluvium, or tin mining slimes, overlying the limestone. It is only recently that large buildings have been constructed in the area. Arup Jururunding have been concerned with several projects located on the limestone, although space here only permits the description of four sites in detail. The experience has allowed the development of a design approach for the foundations. The aim is to make the architectural scheme compatible with the geology. This is not always possible, and examples are given of both situations. The case histories give examples of compensated foundations, and piled foundations include steel H-piles, precast concrete piles, micropiles, bored piles with rock sockets, and barrettes up to 90m deep.

Jan 1, 2010

By J. B. Gayle

During the past several decades, there has been a steady increase in the number and size of experimental ovens used for carbonization research. Although many were originally intended principally for studies of coal expansion, current practice usually includes determinations of the properties of the experimental cokes. With respect to size and shatter characteristics, the cokes from the larger experimental ovens closely approximate those from duplicate charges carbonized in commercial ovens; however, they are consistently lighter and frequently less resistant to degradation by abrasive forces. To minimize these differences, some operators dry the experimental charges before carbonization. The resulting higher dry coal charge densities do, in fact, yield cokes with gravities closely approximating those produced commercially from the same coal or blend but without drying. The drying of the experimental charges may be criticized on the grounds that it represents a departure from commercial practice and may result in oxidation of the samples; for these reasons, the practice has not been universally adopted.

Jan 1, 1961

By L E. Krause

This paper discusses the considerations for optimum maintenance of critical ore handling infrastructure in order to minimise the cost to the business of maintenance periods. As maintenance periods are a direct interruption to production, time is of the essence and careful management of shutdown periods is essential. The ore pass systems currently in use at Xstrata Copper û Mount Isa Copper Operations are up to 30 years old and have had significant wear over the years. The maintenance of these passes and their brows and chutes in a production situation is a challenge as it can potentially expose personnel to high risk situations in addition to the production interruptions. Some alternatives for mitigating the risk of working in ore passes including plugging and ballooning are described. Criteria are included for selecting a method for the safe entry into a given ore pass. Experience in adapting the method of ore pass plugs and some lessons learnt in the process are also discussed.

Jan 1, 2005

By Jack Washburn, E. R. Parker

Kinking in zinc single-crystal tension specimens was observed under conditions of low stress and high temperature. Kinking is discussed in relation to other plastic bending phenomena on the basis of dislocation theory. Experiments on the stress-induced motion of small angle boundaries are reported. KINKING was first reported by Orowan1 as a new deformation mechanism. He observed the phenomenon in cadmium single crystals loaded in compression. Glide lamellae in a local region of the rod were observed to snap over suddenly to a tilted position, resulting in a sudden shortening of the specimen. Between the tilted portion and the rest of the crystal there were fairly sharp boundaries, with the slip plane assuming approximately mirror image positions on opposite sides of these boundaries. Orowan considered the boundaries to be regions where dislocations had concentrated. Hess and Barrett' observed the formation of kinks in critically oriented zinc compression specimens. It was found that the sudden snapping over of the tilted region was not an essential part of the kinking phenomenon but rather was associated with the method of loading. Kinking was explained on the basis of the accepted mechanisms of slip and flexural glide. It was also suggested that a kink can be considered as a special type of deformation band. During a recent investigation of the effect of surface condition on creep of zinc single crystals," a similar phenomenon was observed in crystals which were loaded in tension. The specimens were 0.4 in. diam cylindrical rods with a free length of 4 in. between end connections. All of the crystals were tested at a constant load. adjusted to give an extension rate of approximately 0.05 pct per hr. Kinking, as shown in Fig. 1, occurred in some of the tests performed at temperatures above 200°C. Kinking was observed in specimens varying widely in initial orientation, scattering about a 45" angle between the slip plane and the specimen axis. The condition leading to kinking in tension appeared to be non-uniform distribution of flow along the gage length combined with the restraint imposed by the tensile load. At low temperatures and fast strain rates, the distribution of strain throughout the midsection of tension specimens was generally quite uniform; therefore, bend planes developed only near the ends as described by Miller.4 However, at high temperatures under creep conditions it was difficult to obtain specimens in which the distribution of flow was uniform. Some of the factors which may have caused differences in flow stress along the length of the crystals are: Nonuniform distribution of impurities, accidents of growth (lineage structure), slight bending or other damage during handling, surface conditions, and strain-aging characteristics due to dissolved nitrogen." Plastic flow, once started in a local region, often continued to a relatively large strain before other parts of the gage length became active. Under these conditions a series of kinks, such as those in Fig. 1, were produced. Fig. 2 illustrates how a nonuniform distribution of slip produces bending moments which- are responsible for kink formation. If no plastic bending were to occur while the rod extended by pure slip in two separate sections of the rod, it would assume a shape such as that in Fig. 2a. A specimen having this shape and being subjected to a tension load would have concentrations of stress at the concave surfaces C and lower than average stress would exist at the convex surfaces D. Therefore a bending moment is superimposed on the average stress in the regions between C and D. The positions of potential bend planes under these conditions are shown as dotted lines. Actually no such shape as Fig. 2a develops because plastic bending in the region C-D occurs simultaneously with pure slip in the intervening regions. The observed structure of a tension kink is indicated by Fig. 2b. Perhaps the best approach to an understanding of kinking as well as other related plastic bending phenomena, such as the bend planes discussed by Miller,' cell formation studied by Wood et al.,6 and polygonization,7 is consideration of the dislocation model of a bent lattice. Current theories of the slip process postulate generation or multiplication of dislocations at certain lattice imperfections. The mechanism proposed by Frank and Read8 results in continuous generation of concentric dislocation loops which spread out

Jan 1, 1953

By J. J. McClellenand, R. A. Jankowski

Face ventilation and water sprays are the primary controls used on continuous miner sections to protect workers from respirable coal and silica (quartz) dust. Laboratory tests were conducted by the U.S. Bureau of Mines to determine the impact on respirable dust concentrations when increasing airflow from 3000 to 9000 cfm (1.42 to 4.25 m3/sec), water flow from 15 to 35 gpm (0.057 to 0.132 m3/min) , and water pressure from 80 to 200 psi (5.52 x105 to 1.38 x106 pa). The effective limits for each control and interactions between these controls were of particular interest. Initial analysis concentrated on defining the impact of the control parameters on the respirable fraction of the feed dust, which was a blend containing 90% coal and 10% quartz. Gravimetric sampling indicated that airflow had the most significant individual impact on respirable dust levels and resulted in reductions of 99% at the operator and 57% in the return. Regression modeling was used to predict dust concentrations at the operator and in the return. Significant interactions were observed between control parameters and often, defined the level for a control parameter where increases above that level did not significantly benefit dust control. Increasing airflow to 8400 cfm (3.96 m3/sec), water flow to 25 gpm (0.095 m3/min), and water pressure to 140 psi (9.65 x105 Pa) typically provided respirable dust reductions at both sampling locations, while optimizing use of control resources. After determining these relationships for the total respirable fraction, selected filters were analyzed for quartz content to define the impact on the quartz component of the feed dust. For the individual control parameters, airflow again had the most significant impact and resulted in reductions of 98% at the operator and 26% in the return. Regression modeling of the quartz concentrations indicated that no significant interactions between control parameters were present. At the operators location, airflow was the only parameter identified as having a statistically significant reduction for quartz dust. A reduction in quartz approaching 95% was observed for increasing airflow to 6000 cfm (2.83 m3/sec). Increases above 6000 cfm had little additional impact. In the return, a linear relationship between control parameters and quartz levels was observed with reductions of approximately 27% predicted for increasing any one control parameter to its maximum level. The synergistic impact of increasing all control parameters to maximum levels resulted in a maximum predicted reduction of 81%.

Jan 1, 1991

By V. M. Paretsky

Recent developments made in the Gintsvetmet Institute in the field of autogenous smelting processes have confirmed that autogenous smelting continues to be the main prospective technology for pyrometallurgical processing of sulfide raw materials. This technology ensures energy conservation and environmental safety conforming to the current world standards for production of heavy non-ferrous metals. Two alternative processes of single-stage autogenous smelting producing white metal as well as high-basic ferrite-calcium slags have been developed and can be recommended for technical modernization of Russian copper smelters.

Jan 1, 2002