Search Documents

By C J. de Beer

The Kwaggashoek East pit is one of the four production areas of Thabazimbi Iron Ore Mine. The Kwaggashoek East Open pit mines through the abandoned sublevel caving operations of the Kwaggashoek East underground workings. A risk assessment indicated that the primary risk is the occurrence of surface subsidence. Based on local knowledge, a hypothesis, that most of the cavities were filled with broken rock as a result of roof collapse and bulking of failed material was formulated. To test the hypothesis a number of geophysical methods as well as probe drilling was utilized. The results of the resistivity, gravity and ground penetrating radar surveys were inconclusive in determining the position of voids. Either there were no voids present or the resolution of the surveys was not high enough to pick it up. It is accepted that only small voids remained, and that the supported roof hypothesis is valid. As a precautionary measure all the production blast holes within the caving area were over-drilled by forty percent. This would collapse the roof of any small voids or tunnels immediately below the block. This operation proved to be successful as two of the three underground levels have been mined out with no subsidence occurring in the pit floor.

Jan 1, 2006

By David C. Kraft

A major manufacturer and user of machine tools had the need to install a screw press machine at its plant site with the following design load requirements: (1) Vertical Compression Live Load = 2000 kip (8896 kN) and Dead Load = 1000 kip (4448 kN), (2) Rotational Moment = 6600 ft-kip (8950 kN'm). The screw press machine was to be located within an existing manufacturing building. The bottom of the footing base was located 15 ft (4.6 m) below existing floor slab. A geotechnical investigation of the site indicated a 17 ft (5.2 m) thick initial stratum of stiff to very stiff clay underlain by a 14 ft (4.3 m) thick stratum of loose to medium dense sand. Beneath the sand stratum was soft rock described as weathered shale. Obvious concern was raised on the possible effects of the dynamic motion of the screw press and potential resulting settlement within the loose sand stratum. This combination of large loads and dynamic motion resulted in the selection of a helical pile and tieback system to support the concrete foundation. The helical pile foundation system consisted of a group of vertical helical piles installed into the shale rock and a group of inclined helical tiebacks set into the remaining portion of the clay stratum. Four load tests were conducted on the vertical helical piles in order to establish compression load capacity. The results of these load tests as reported herein, led to the addition of a limited number of tubular steel push piles in order to meet the project required Factor of Safety on the design loads. All of the helical piles, push piles and inclined helical tiebacks were successfully installed and the screw press is now installed and operational.

Jan 1, 2003

By O. Knacke, H. Barth, W. Gans

The rate of cementation was determined by measuring the time required to consume a thin electrodeposited layer of the cementating metal as indicated by a sudden increase in the electrical potential. The diffusion controlled cathodic current of the more positive metal was measured by conventional electrochemical techniques and compared with the cementation rate under the same experimental conditions. Micrographs revealed different types of crystal growth in different surroundings e.g. dendritic growth in acidic solutions.

Jan 1, 1973

Jan 1, 1944

1910, hundreds of thousands of dollars of work and equipment in a 1500-foot shaft, crosscuts and pumping had found only copper-lean pyrite in two cross- cuts, and nothing in a third. Going aimlessly along the third crosscut one day, after looking at the barren face I happened to notice a dark spot in the white limestone, near the floor on one side. I picked, and found it was a little triangle of rich chalcopyrite. Next day I took Bill Gohring, then mine superintendent, in to see it. He said nothing else had succeeded so we might as well try that. The new drift broke into a full face of high grade copper ore in the first round, and continued in rich ore for 2200 feel broken only by a couple of short stretches of lean pyrite. The earlier crosscuts had happened to cut these lean areas. Q: Was there any single thing that called your attention to that little dark spot in the side of the Briggs crosscut, rather than to any other discolored spot? Joralemon: Nothing very definite. Maybe luck, maybe that indefinable subconscious thinking that

Jan 9, 1964

By A. L. Field

Previous Publications THE first report on the slag viscosity work of the Bureau of Mines was made by one of the authors 1 in 1916. It was concerned chiefly with, the method of measurement. A paper 2 on this phase of the work was presented to the Institute in February, 1917, and a similar paper 3 was communicated to the Faraday Society. Purpose and Scope of the Slag Viscosity Tables Following the development of a suitable method, the next step in the investigation was the measurement of slag viscosity over a wide range of temperature and composition, and the arrangement of this experimental data in the form of tables for the use of the blast-furnace operator. It is believed that this information, if used intelligently, should help the operator to reduce losses in production caused by off-grade pig iron, to improve fuel economy, to promote operating efficiency, and to extend present-day practice to meet the increasing need of smelting lean and complex ores. In the experimental part of the work it was early observed that the temperature-viscosity relations of a slag were determined, for practical purposes, by the relative proportions of the three major constituents, lime (CaO), alumina (Al203), and silica (Si02), provided the percentage

Jan 12, 1917

The main factors which influence disposal of mine waste under New Zealand conditions are identified and discussed: namely, geological conditions which produce soft weather-sensitive waste, wet and cold winters which affect productivity in such waste, elevated seismicity which affects stability and the need for water rights which involve public participation. The waste disposal scheme for the Martha Hill Project is described, thereby illustrating how these factors influence the planning of a current mine strippings and tailings disposal scheme.

Jan 1, 1986

By B J. Andrew, M R. Daley

Mount Isa Copper Mines is a world-class mining operation producing approximately six million tonnes of ore per annum. With over 50 years of mining history and over 76 million tonnes of underground resource remaining there are many challenges facing the mine technical team today and into the future. The mine consists of nine distinct areas: the Hangingwall Lens, Footwall Lens, 1100, 1900, N1100, N1900, 3000, 3500 and N3500 orebodies. Each of these areas have different characteristics, requiring varying methods of mine design and ground control for safe and efficient orebody extraction. Each of the areas operate with an independent sequence whilst interacting with the entire underground operation. Within the first five years after graduating mining engineers tend to orient their careers in either a technical or operations direction. Engineers working towards a specialised technical career will often be working as mine planning engineers, whilst others more focused in the operations stream occupy roles such as operations or project engineers. At this stage of a mining engineerÆs career they are not yet categorised into one stream or another, but career decisions made now can generally focus their ultimate career path in one direction or the other. Due to the size of the Mount Isa operations there are many opportunities for engineers pursuing both career path and plenty of room for growth forthose as yet unsure.

Jan 1, 2005

By Jerold Bishop

The application of the ?electro-hydrodynamic effect? (EHDE) to civil engineering has been made in the construction of drilled piles. Equipment for the commercial application of this process was developed in Russia in the late 1980's. The process is approved for general use by the Russian Federation building code and numerous projects have been successfully completed with this technique. EHDE is a process by which a moderately powerful shockwave is released in the bottom of a drill hole filled wet concrete slurry. The energy is carried outward through the fluid with minimal loss because it is an incompressible medium. Repetitive discharges provides a series of energy pulses which will compact the soil along the pile shaft and at base of the pile. The process is analogous to repeated applications of low energy blast densification or to dynamic compaction. In general, the process is not depth dependent. Repeated application of this treatment in a drilled pile hole can increase soil density at the base and along the shaft of the pile, as desired. The overall result is that the geotechnical capacity can be improved significantly. Test results documenting improvements are presented and other applications considered.

Jan 1, 2007

By E. h. Erwin Gaertner

Before dealing with the technical equipment of this paper a short survey of the Rhenish Brown Coal Area is given in order to illustrate the special geologic and environmental conditions in this region, which led to the development of the mining technics, used today.

Jan 1, 1975

By W. Sondermann

"AbstractWith the increasing demand in reuse of inner city areas and the urgent need for deeper foundation pits under cramped circumstances, adjacent structures close to and high ground water level, the well-known established technologies especially with small to mid-sized dimensions are often too time consuming and occasionally not economic to install lateral support systems. The alternatives for these specific cases could be the usage of the deep mixing technology to create lateral support systems in reinforcing the deep mixing elements additionally to transfer the horizontal loads from earth – and water-pressure.With increasing demand in depth and water tightness, verticality and overlapping of single column solutions are becoming the key in execution. In addition, for some applications subsoil-conditions were not ideal for wet deep mixing technologies. The tubular soil mixing system (TSM) as a combination of mechanical mixing and support of hydraulic cutting by jet grouting can provide solutions toovercome these challenges.1. Current market conditions and trendsThe present financial crisis and the efforts not only to consolidate national budgets, but also to rescue certain banks, have not left the building industry unaffected either. Some drastic cutbacks to public budgets, along with the increasingly restrictive granting of credit for the financing of construction projects, have led to enormous over-capacities in the building sector, with purely negative impact. As a consequence of these negative developments, many companies are experiencing the pressure to restructure more quickly and to reduce costs but at the same time to keep the consequences of all activities, both externally and internally, within limits acceptable to employees, owners and finance institutions and last but not least consumers."

Jan 1, 2014

By Paul Soros

There has been a steady increase in shiploading capacities in the last 20 years. One of the reasons has been the general increase in ship sizes, with the largest vessels currently around 280,000 DWT in the bulk trades. Obviously, the large vessels can accept loads faster and their economic utilization justifies higher loading rates, up to a point. The high capacity facilities have loading rates far beyond this point. The economic logic of these facilities is based on the fact that for a given annual throughput the capital and operating cost of a single high capacity system is less than that of two smaller systems. Thus, where the projected throughputs are large, there is a great incentive to reduce capital costs by maximizing capacity. Tubarao, in Brazil, designed for a 100 million ton per year throughput with one finger pier and one high capacity berth is a successful demonstration of this approach. In the current state of the art, the high capacity systems have shiploading capacities in the range of 10,000 - 16,000 TPH, for annual throughputs of 20 million tons and larger per loading berth.

Jan 1, 1982

Experimentation which measures differences in pressure across the interfaces of immiscible fluids in the interstitial spaces of porous media may be termed "capillary pressure experimentation". In the literature of petroleum technology since 1941 there have appeared twelve papers popularizing capillary pressure concepts and developing applications of these concepts for the solution of problems of practical reservoir engineering importance, such as the determination of connate water, fluid distribution. in transition zones, reservoir rock textural properties, and oil recovery from petroleum reservoirs.' Although a review of the literature would be justified at this time in order to reconcile the conflicting viewpoints which are contained in the cited papers, the object of this note will be of more limited scope. It is believed that the recent paper of Muskat alls sufficient attention to many of the uncertainties which arise upon examination of the published literature. such that until satisfactory counter-proposals can be made it will serve our purpose only to mention some other like uncertainties. This will emphasize further the need confronting petroleum technologists to re. consider and reformulate the application possibilities of capillary pressure experimentation. In particular, I sug- gest that we examine the thesis that capillary pressure experimentation as above defined can lead to measurements reflecting the recovery of oil from petroleum reservoirs, as was proposed first" by Amyx and Yuster" and was first reduced to practice by the experimentation of Welge. In fact. I shall deal exclusively with the Welge papers since it is the principle one on this subject which has appeared to date. I shall attempt to show that the possibility of describing oil recovery features in terms of capillary pressure phenomena has not been established entirely. The Welge paper was a pioneering effort to evaluate this recovery application possibility. P. P. Reichertz' comments on the Welge paper state that non-wetting phase discontinuities are developed occasionally in the Welge experiment, and restate Muskat's argument that discontinuous fluid elements (partially saturating the interstices of porous media which are elsewhere saturated with some other immiscible phase or phases) are not subject to the requirements of hydrostatic equilibrium. It is the purpose of my comment to show that it is unnecessary to make Reichertz' postulation regarding non-wetting phase discontinuities (however valid) when it is desired to criticize welge's theoretical treatment of his problem. It can be shown that Welge's method of measuring values for ''capillary pressure" is invalid in many instances of application, such that his reported curves of capillary pressure Versus fluid saturation often have no physical meaning, even throughout the interval of fluid saturation where it might be otherwise suspected that no phase discontinuities occur. By considering established principles of capillary pressure experimentation it can be shown that the pressure difference experimentally observed between wetting and non-wetting fluid Phases which are contained in external reservoirs will reflect on the capillary pressure difference at the interfaces of contact between these phases only when the following conditions are satisfied: (a) There shall be a balance between the opposing forces of gravity and capillarity, as obtains under conditions of hydrostatic equilibrium when the positions of the interfaces of contact become fixed in pore spaces of certain geometry (b) The wetting and non-wetting fluids within the interstitial spaces shall everywhere be continuous with the external wetting phase reservoir and the external non-wetting phase reservoir, respectively. It will become apparent immediately that in any instance when a greater pressure is recorded in the external wetting phase reservoir than in the external non-wetting phase reservoir, one may establish either that static equilibrium has not been attained or that discontinuities in one or more of the fluids have been developed. This is because the pressure otherwiee is always ereatest in the non-wetting phase at each static interstitial interface of contact with the wetting phase. such that the externally measured pressure in the non-wetting phase likewise must be greatest if the above conditions are to be satisfied.

Jan 1, 1949

By Maria Kuttig, Christian Ruback, Gerhard Tober, Petra Maier

"It has been demonstrated that there is a strong relationship between work hardening with various post heat treatment and cyclic deformation behavior of structural steel S275. This study contributes to a project developing a process for the complex forming of steel, which combines rolling and bending. Due to the complex geometry of the final work piece, the deformation degree varies greatly. The forming temperature, as well as post heat treatruent, influences recrystallization processes in dependence of the local deformation degree, resulting in inhomogeneous microstructure of the work piece, which affects the quasi-static and dynamic properties. Cyclic creep and hardening or softening has been monitored during constant amplitude loading at stresses near fatigue strength in normalized condition. Work hardening, stress relief or recrystallization influence the cyclic deformation behavior and produces cyclic creep effects. Cyclic softening or hardening and creep were observed to occur in parallel. To what extent these properties are noted depends on the deformation degree.IntroductionThis work is part of a research project developing a new process for the three dimensional forming of steel. For the final product the fatigue strength influenced by the forming parameters is very important. Due to its complex geometry, the formed final plate has different deformation degrees. This leads to different recrystallization behavior and heat treatruent will have different effects on the microstructure. The peak deformation degree cp of the plate will be around -0.5 what leads to the analysis using rolling from 22 mm to 13 mm of thickness. The quasi-static material properties are very important for calculating the preliminary design. However, work pieces which are cyclic loaded need fatigue tests to describe the in-service material behavior. [l] For the prediction and to guarantee the wanted life-time of the part cyclic deformation tests are important. [2, p.23-32] When it is assumed that the work piece will only loaded in cyclic tension, fatigue testing will be done from zero to a maximum force value. In preliminary tests this value is the tensile fatigue strength from a Smith diagram. During processing, here forming, work hardening takes place resulting in strengthening. Therefore, in further tests maximum load can be increased to monitor cyclic deformation mechanism in more detail. However, to study cyclic creep and hardening and softening data should be evaluate over sufficient life time and should not fracture too soon."

Jan 1, 2013

By Jhon F. Chávez

"El presente texto describe las técnicas de análisis, diseño y optimización de las mallas de sostenimiento activo, de forma que optimiza las condiciones de seguridad y reducción de costos de sostenimiento en las labores de la minera Iscaycruz, así como los sobrecostos por daños a instalaciones y equipos por accidentes relacionados a falla en el sostenimiento activo."

Jan 1, 2016

By Fathi Habashi

Poland has a unique copper industry. Copper sulphide concentrates are smelted in six shaft furnaces to produce matte and in a flash furnace directly to blister copper. Anodic slimes from electrorefining are treated by a modern technology to recover the precious metals. INTRODUCTION Poland's copper industry began in 1950 when the old and relatively small mines Lena and Konrad, located in Lower Silesia, were drained and recommenced production. In 1957 the industry entered a period of rapid development with the discovery of a rich ore body in the vicinity of Lubin and Polkowice which was the basis for the establishment, in 1961, of the Copper Mining and Smelting Combine (KGHM). In 1991 the Combine was restructured into a state-owned, joint-stock company under the new name of KGHM ?Polska Miedz? (KGHM ?Polish Copper?). It consists of three mines, three smelting and refining plants, and one rolling mill, and produces about 4% of the world?s copper and about 7% of the world?s silver.

May 1, 2001

By Christopher Bambridge

The Washington State Department of Transportation (WSDOT) is constructing a new tunneled route under Seattle to replace the existing State Route 99, Alaskan Way Viaduct (AWV), which follows the historic waterfront for several miles. The viaduct separates the businesses that rely upon the tourist trade from the down-town area. The reconnection of the city to the waterfront areas will occur following the completion of the SR99 Re-placement program that replaces the aging structure that was severely impacted by the 2001 Nisqually earthquake, with a state-of-the-art, twin-deck highway with a world record-breaking 17.4-m (57.3-ft) bored tunnel. Constructed in the 1950s, the double-tiered viaduct is nearly 3.2 km (2 miles) long and runs parallel to city?s waterfront. The viaduct, which is partially supported by the seawall, is a vital local and regional transportation link and carries about 110,000 vehicles each day. The seawall, built from concrete and timber in the 1930s, extends along Seattle?s waterfront and supports the soil behind it. Studies in the 1990s showed that the viaduct was nearing the end of its useful life, apparent by its exposed rebar and weakened columns. The 2001 Nisqually earth-quake further damaged the viaduct, forcing WSDOT to temporarily close it for inspection and limited repairs. The viaduct and nearby seawall are vulnerable to an-other earthquake and continue to show signs of age and deterioration. Following a collaborative process, WSDOT developed the following guiding principles to the viaduct replace-ment:

Sep 1, 2013

This paper deals with innovative techniques that have enabled personal computers to be used on the mine site to define, develop and manage an ore body resource, while being aware of the consequences to the environment. The same set of personal computer tools that are used for resource estimation, once the province of expensive workstations, can also be used by geologists, mining engineers, surveyors and environmentalists, in managing the whole mining process, including production, grade control, monthly reconciliation and stockpile management through to tailings the management, mine rehabilitation and the due diligence process of mine closure.

Jan 1, 1996

In-pit crushing and conveying (IPCC) is being increasingly considered as an alternative to traditional truck-shovel mining methods. The move towards IPCC is driven by a number of factors including the potential to reduce greenhouse gas emissions, the availability of skilled labour and the need to increase extraction rates to levels that present significant challenges to traditional methods.When considering the relative performance of IPCC and truck-shovel methods, the outcome can be inadvertently impacted by either the use of different simulation approaches, or techniques that do not adequately model the processes in sufficient detail.A simulation approach is proposed that models both IPCC and truck-shovel using the same software platform and is capable of functioning at a wide range of resolutions from life-of-mine scale through to second-by-second asset tracking level. The simulation framework also holds models of processing equipment and hence the mining simulations can be extended to gauge the impact on downstream plant.The approach, known as mine-process operational simulation (MPOS), can be tailored to the level of information available and hence the type of study required, ie order of magnitude, prefeasibility, feasibility, or detailed design.Using information from block models and a range of detailed equipment and process models, MPOS can span major system discontinuities, typified by the mine-plant interface, to allow the estimation of final mine and plant product specifications.

Dec 6, 2010

By C. H. Jr. Herty

THE elimination of metalloids in the open-hearth process depends on oxidation of the metal by diffusion of FeO from the slag (or absorption of FeO by the metal), with subsequent reaction between dissolved iron oxide and the metalloids carbon, manganese, phosphorus, and silicon. During an investigation on deoxidation with silicon, data on rate of oxidation of the metal were obtained, and these combined with certain other information, are presented here in an attempt to show the fundamental principles governing the diffusion of FeO from slag to metal. Inasmuch as the aim of the investigation was not a study of diffusion, certain data are lacking and it has been necessary to make assumptions on metal viscosity and effect of temperature on diffusion. These factors are known to exert a considerable effect on diffusional processes. Overoxidation, or supersaturation of the metal with iron oxide, is not taken up in this paper. Overoxidation has little effect on diffusion except under a few special conditions, and the discussion has therefore been limited to diffusional processes. Though the results given in this paper should be regarded as preliminary, certain of the conclusions drawn are definitely applicable to any steelmaking process.

Jan 1, 1929