Search Documents

By A. Haines, O. Varaud, I. Baidoo

Abosso Goldfields Limited (AGL) is in the process of developing an expansion of their Damang Open Pit gold mine in Ghana. AGL acquired the Damang mine in January 2002, with SRK participating in the geotechnical investigation and design for the project since 2001. A deep resource drilling program, completed during 2004, intersected an extension of the orebody below the then planned final pit floor. A feasibility study has been completed to determine the economic extraction of this deep ore with an expanded pit shell. The Damang mine is in a stockwork sulphide deposit at the culmination of the Damang anticline. The deposit occurs as hydrothermal mineralisation associated with dominantly east dipping thrusts and sub-horizontal quartz veins. Primary gold mineralisation also occurs in the conglomerates of the Tarkwaian Formation. The geological units consist of steep easterly dipping dolerite, sandstone, siltstone and phyllite beds, with the weathering profile comprising saprolites overlying a relatively thin joint oxidized horizon. It is planned to deepen the current open pit to a final depth of up to 270 m, primarily by the development of a push-back of the eastern and western walls. The edge of the Eastern Tailings Storage Facility (ETSF) is currently located within 80 to 100 m of the crest of the existing pit. The geotechnical design focused on the optimization of the bench face angle and finally recommended a ?Steep Slope Strategy?, involving 24m high near vertical benches. Limiting bench stack heights of 96m at a maximum of 66° were derived from the influence of major structures and the variation in rock mass conditions. The overall slope angles in each pit sector were developed around the requirement for haulage ramps. One of the main design challenges was to optimise the standoff distance between the final pit crest and the ETSF. This process had to consider maximum access to the resource without undue influence on or from the nearby tailings dam. A planned increase to the height of the dam wall was an additional factor in the design. Dewatering of the pit walls was also a major consideration in this tropical environment.

Jan 1, 2006

By G. N. Carlson, C. H. Hazelroth, D. R. Dorrance

"Located on the north shore of the St. Lawrence River at Pointe Noire, Quebec are the agglomeration and ship-ping facilities of the Wabush Mines complex. Here, the specular hematite concentrate from the Scully Mine is received for further processing. Modern facilities for handling the ore, either to the 1plant or to stockpile, provide quick and efficient operation of the ore receiving station. Physical preparation of the ore for balling is accomplished with regrind ball mills, filters, bentonite crushing and drying facilities, pumps and related conveying circuits. Rotating table feeders deliver the reground and de-watered ore from storage bins to balling drums, where green ball or green pellet formation is achieved. The green balls are then conveyed to the indurating section. Three Dravo-Lurgi travelling grates, producing a total of 6,000,000 long dry tons of pellets per year, are used in the indurating phase of the operation. These grates, having 38 windboxes and firing at a temperature of 2,500°F, harden the pellets for shipment to various blast furnaces throughout the world."

Jan 1, 1969

By Jeffrey A. Gebhard

As part of the design and construction of the new St. Anthony Falls I-35W Bridge, a full-scale load test was conducted on a 6 1/2-foot diameter drilled shaft in the St. Peter Sandstone. This load test helped identify shaft-rock interaction properties, including end bearing and multiple zones of differing shaft resistance for design of the drilled shafts beneath the three piers adjacent the river. The load test was designed by Load Test, Inc., Braun Intertec and the design team of Figg Bridge Engineers/TKDA and constructed by Design Build Consortium of Flatiron/Manson. Oversight was provided by the Minnesota Department of Transportation. Based on these test results, the drilled shafts supporting the St. Anthony Falls I-35W Bridge were designed to reduce risk and maximize economy for the people of the State of Minnesota.

Jan 1, 2009

By S Q. Liu, E Kozan

This paper proposes a new multiresource multistage scheduling problem for optimising the open pit drilling, blasting and excavating operations under equipment capacity constraints. The flow process is analysed based on the real-life data from an Australian iron ore mine site. The objective of the model is to maximise the throughput and minimise the total idle times of equipment at each stage. The following comprehensive mining attributes and constraints have been considered: types of equipment; operating capacities of equipment; ready times of equipment; speeds of equipment; block-sequence-dependent movement times of equipment; equipment-assignment-dependent operation times of blocks; distances between each pair of blocks; due windows of blocks; material properties of blocks; swell factors of blocks; and slope requirements of blocks. It is formulated by mixed integer programming and solved by ILOG-CPLEX optimiser. The proposed model is validated with extensive computational experiments to improve mine production efficiency at the operational level. The model also provides an intelligent decision support tool to account for the availability and usage of equipment units for drilling, blasting and excavating stages.CITATION:Kozan, E and Liu, S Q, 2014. An Open pit multistage mine production scheduling model for drilling, blasting and excavating operations, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 329–334 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By Raymond F. Moran

The history and development of the FMC Coke process has been reported in numerous presentations over the past 10 years (1, 2, 3, 4, 5, 6) but a short review is desirable, especially regarding the aspects that are influenced by the coal to be used. F'MC has been developing this process in pilot facilities since 1956 and in a modest sized plant in Kemmerer, Wyoming since 1960 (Figure I). This plant produces strong uniformly sized coke briquettes from a completely non-coking coal, namely Elkol, a sub-bituminous coal of the Adaville seam. Since operating commercially, over 300,000 tons have been produced, 90% of which has been used in electric phosphorus furnaces and some 10% of which went for trials in iron blast furnaces. We believe that this commercial use of non-coking coals is a unique experience in the history of coke manufacture.

Jan 1, 1975

By D. Brady

There are many examples, historical and recent, from the underground coal mining industry where during emergency response the response and ultimately the outcomes, could have been significantly improved if adequate systems had been in place for the collection and management of relevant information preceding the incident, the acquisition of information during the incident and the use of the information for risk mitigation and decision making purposes. The subject and process of knowledge management is possibly the most critical for would be rescuers of endangered coal mine workers, as it has been demonstrated at numerous coal mine incidents that a lack of or mismanagement of crucial information can be fatal for both the rescuer and/or the endangered coal mine worker. This paper will underline the scope and importance of robust knowledge management systems for emergency response within the underground coal mining industry and the process by which it is being achieved within the Queensland Mines Rescue Service and the NSW Mines Rescue Service.

Jan 1, 2012

By Brian Hester

Many Third World African countries are well-endowed with minerals - especially gold and diamonds - while only a few have important base metal deposits. For decades since colonial rule, political and economic conditions discouraged interest by Western capital. Influence from Soviet Bloc countries, however, has declined with the move toward multi-party rule. And the left wing orientation, once widely favored by Third World African countries, has almost disappeared. With International Monetary Fund (IMF) encouragement, these Third World African countries now encourage representational government and solicit western finance to expand their industries. Mining is especially encouraged. The North American mining industry is following the same trail as other capital intensive industries and looking abroad for opportunities. The Prospectors and Developers Association of Canada released figures that show exploration expenditures in that country were halved between 1987 and 1990. Figures for the United States are not so easily found but every indication points to a downward trend. While total annual expenditures on US exploration by corporations as a group are either declining or remaining constant, expenditures away from North America is increasing. Gold exploration expenditures in 1991 by the major companies tracked by Minerals Economics Group were less in the United States than for Latin America and the Southwest Pacific combined. The same study showed as much was spent in the Republic of South Africa and "Other" areas combined as in the United States. Expenditures by major corporations in these "Other" areas amount to only 5.2% of their total budget. Third World Africa is a major component of these "Other" areas.

Jan 1, 1993

By Scott Hean

"Environment and the economy are interwoven irrevocably. They need to be publicly discussed, and discussed often so that new approaches can be understood and developed - approaches which are complimentary, not confrontational.Discussion on the environment is timely, from the perspective of mining engineers and developers, from that of bankers and from their shared perspective as people concerned with enhancing the quality of life, the environment and the economy.This paper will touch on how what is called the ""environmental economy "" that has evolved has become entangled with regulatory and financial issues in a way that is dangerous for all of us. It will also look at some of the promising possibilities that a world-wide and continuing concern for the environment holds out for us.For many decades, British Columbia has provided some of the key examples of the intertwining of environmental and economic issues, and, very importantly, providing the people prepared to do something about them.Canada's first environment minister, the late Jack Davis, came from British Columbia. He led this country's delegation to the Stockholm Environment Conference in 1972, a conference that laid the groundwork of principles necessary to establish some international certainty as to the legal liability for causing trans-national environmental damage.Another British Columbian who was also a national environment minister, John Fraser - now the Speaker of the House of Commons - was one of the first to dramatize the importance of acid rain and force it into the international public arena.Some 20 years ago, British Columbians made Vancouver and their province one of the major centres of opposition to the Alaska Pipeline and Tanker System - with some justification, it now seems.That a British Columbian , then MP David Anderson, was given legal recognition to sue in a United States' court against a system that was either in U.S. territory or international waters was an important precedent in, and of, itself in terms of environmental law. That old controversy is now a very current case study - in terms of dealing with the question of liability.-"

Jan 1, 1991

By Juan B. Cabezas

"The favorable characteristics and workability of plastics as a replacement of wood, lead, stainless steel, asphalt and other materials are described. Various types of plastic have proven to be the most favorable choice for handling a variety of acidic, alkaline and organic solutions, as well as pulps, chemical wastes, slurries or tailings for impoundments. The material origin of various plastics, methods of manufacturing and specifications applied to leaching solutions are discussed, including availability and costs. Examples of select plastics are considered for use as alternatives of other materials under severe environmental requirements.IntroductionHydrometallurgical processes applied to gold recovery, as well as other metals, require the use of strong solutions of alkaline, acidic or organic nature, and may also include a variety of materials with extraneous characteristics and complications for handling in storage.The technology of leaching has been in use for more than 100 years, but the applications of leaching processes in metallurgy have become more commonly used in the last 15 years. Suitable materials for the construction of containers, launders, piping, and various accessories, to be used in the handling of leach solutions or slurries, have become a serious problem. Various metals such as brass, lead, stainless steel, etc., and non metallics including wood, clays, glass, rubber, ooncrete, tars or miscellaneous compounds have been tried in the past with serious limitations in workability and resistance to wear and corrosion. For example, the use of metallic, wooden or glass piping systems would require extraordinary shop maintenance to keep such systems in operation"

Jan 1, 1997

By Mark Abernathy

When most people think of a motor vehicle accident, the direct costs resulting from that accident, such as vehicle repair or towing charges, are generally easy to quantify. However, the indirect costs associated with an accident are often overlooked. These indirect costs can take a tremendous toll on a company in more ways than you might think.

Jan 1, 2006

By J. Paraszczak

Application of teleoperated and automated (or ?autonomous?) mobile equipment in underground metal mines represents a promising avenue for overcoming some of the challenges facing the industry. This paper addresses the overall effectiveness of autonomous loading and haulage equipment compared with conventional human-operated machines. Factors affecting availability, utilization, and production rate are explored, and an emphasis is placed on some problems and risks not present in conventional human-operated systems, as well as on the character and criticality of autonomous equipment. The need for a more in-depth analysis of factors affecting overall autonomous equipment effectiveness is stressed; these factors should be taken into consideration at the stage of feasibility studies. The paper concludes with recommendations and directions for future research.

Aug 1, 2010

By V. J. Sikora, T. S. Hutchinson

This paper presents a method for making a water-rlrive ana1gsis without prior knowledge of aquifer geometry and uniformity using a standard desk calculator. Although it is necessary to know the initial oil in place to use this method, this is a minor limitation to the scope of (he method since in most reservoirs it is possible to obtain reasonably accurate volumetric oil-in-place estimates. An equation is developed which relates pressure at the water-oil contact to the water influx rate as a function of time by a factor called the resistance function. The resistance function introduces the composite effect of the aquifer geometry and flow resistance disrribution. It is pointed out that the characteristic shape of this function makes it possible to start with on approximation of the function and successively improve the approximation until the correct resistance function curve is obtained. In this fashion water-drive estimates can be made without the limitation of assuming simplifed aquifer shapes and flow distributions. This is the novel feature of this development. Methods are given for extrapolating the final curve to calculate future aquifer behavior. Equations are developed for adjusting the pressures and water influx rates where it appears that possible errors in these quantities make it difficult or impossible to obtain a useuble resistance function curve without this adjustment. Application of the pressure build-up analysis techiiique to estimate. some of the aquifer properties is also presented INTRODUCTION A great many oil pools are the result of oil accumulation in some type of trap in an otherwise large and continuous porous stratum. The void space of this stratum outside of the oil pool itself is filled with water or brine. In analyzing performance of the oil pool surrounded by this water aquifer, it is quite necessary. in most cases, to include behavior of the water. When the pressure at any point in a fluid system is lowered, such as by opening a well in an oil sand, fluids in the immediate neighborhood of this point will begin flowing towards this lower pressure sink. As pressure in this area drops due to flow towards the sink, fluids from farther out will start to flow towards the lower pressure. As more and more fluid is removed from the system, the distance from the sink or well within which flow is occurring will continually increase; that is, thc region of disturbance will grow. If some rigid boundary such as a fault is reached by the disturbance, this area will cease to grow; but if some movable boundary is reached, such as a water-oil contact, the area will grow on out into the water, although rate of growth may and almost always does change. The relation between amount of pressure drop and amount of fluid flowing at any point and at any time in an aquifer depends on such factors as compressibility and viscosity of the fluids, the porosity and permeability of the rock, geometry of the whole system and withdrawal rate or pressure drop. With these factors known, it is theoretically possible to calculate the pressure-flow behavior of the system, However, in practice true solutions to the problem are next to impossible due to complexity of reservoir systems. A number of approximate methods of solution have been developed based on various simplifying assumptions. One frequent assumption is that the water-oil contact can be located and equations defining oil reservoir and aquifer solved separately by assigning values to various parameters so as to match past pressure and production history. Usually the properties of the aquifer are not known, since few, if any, wells are drilled through the aquifer; but the water influx and the pressure at the reservoir boundary are known over some time. If it can now be assumed that the aquifer is circular, pie-shaped, or linear, and that it has uniform properties, it is possible to fit a theoretical dimensionless curve to the past aquifer performance history and therefore calculate future water drive. These theoretical curves are available in the literature,1,2,3 Of course, the assumption of uniform aquifer properties is almost always somewhat in error. Fortunately, however, moderate variations from the average have little effect on behavior of the system; and, hence, the best fit of a theoretical curve is frequently satisfactory. In other cases variations in aquifer properties and geometry are large enough that none of the available theoretical curves will give an acceptable fit of the data. In these cases, methods of fitting the data with various electrical analyzers have been developed.1,2' It is the purpose of this paper to present an approach

By L. A. Neumeier

A refinement of the tungsten-cobalt phase diagram is presented for compositions to 85 at. pct cobalt and for temperatures to the solidus. Preparation of alloys by powder metallurgy methods is described, and the results of studies made by a combination of techniques involving microscopy, X-ray diffraction, thermal analysis, and dilatometry are discussed. The existence of u-W6Co7 is confirmed (rhombohedral D85 structure). The W6Co7 phase forms periectically at 1,685'115° C by reaction of liquid with primary W; the peritectic melt is at 71 at. pct cobalt. The homogeneity range of u-W6Co7 extends to both sides of the ideal stoichiometric ratio, through a compositional range of about 5 at. pct. The compositional limits for u-W6Co7 vary slightly below 1,471°±5° C, the temperature of the eutectic reaction forming u-W6Co7 plus a. The eutectic composition is at 79 at, pct cobalt. The existence of WCo3 is confirmed (hexagonal D019 structure). WCo3 forms peritectoidally at 1,093°±5° C by reaction between a and u-W6Co7 and exists over a narrow homogeneity range of 0.5 to 0.6 at. pct. The solid solubility of cobalt in tungsten is low (maximum 0,9 at, pct cobalt) and results in contraction of the tungsten lattice. Tungsten is extensively soluble in a-Co at higher temperatures; the a-Co lattice is expanded by the presence of tungsten in solid solution. There was no indication of the formation of a o-phase nor of any intermediate phases other than WeCo7 and WCo3. The WeCo7 and WCo3 phases are compared with similar phases in other systems.

Jan 1, 1967

By Charles L. Kimbell

The estimated value of world crude mineral production in 1990 exceeded $1,501.5 billion in terms of current (1990) dollars, or almost $1,160 billion in terms of constant 1983 dollars. This latter figure was 0.3% below the 1989 level and about 3.9% below the record high to date of $1,207.1 billion 1983 dollars set in 1980. Table 1 provides the latest available revised time series of the estimated value of world crude mineral production both in terms of 1983 constant dollars and in terms of current dollars. It also provides one of the two statistical bases for this estimation, this being the data on the value of production of a group of key commodities that was compiled for and published in the authoritative French language mineral industry periodical, Annales des Mines, for selected years up to 1983.1 It should be stressed that the values just discussed and those presented in the tabulation are for crude minerals only, and by no means reflect adequately the role of the entire mineral industry in the world economy. These figures represent only the value of mineral materials as they are mined or otherwise extracted from the earth. They do not reflect the value added to these materials through downstream processing within the facilities commonly accepted as mineral industry plants. That is, value added through beneficiation of ores, smelting, refining, and similar processing is not included in these figures. Comprehensive world data on the value added by such processing are not available; however, a conservative estimate of the total value of pro-cessed output from mineral industry plants derived wholly from primary (newly mined) materials would be on the order of about $2,780 billion constant 1983 dollars or $3,600 billion in terms of 1990 dollars.

Jan 1, 1993

By J. Peterson, P. G. McKneight, R. W. Riggle

"In today’s tough mining environment, the key difference between surviving and thriving is how effectively miners optimize their mining operations. This paper explores the compounding effects material fragmentation has on mining costs and productivity. Starting with Drilling & Blasting and moving through Loading, Hauling and Crushing, we will illustrate the opportunities to improve operating costs and thus reduce the Total Cost of Ownership (TCO) of the total mining system. Material size and volume requirements are defined by the needs of the mill or plant, and drive the rest of the mining operation from the bench through the primary crusher. At the start of the cycle, where the rock mass is drilled and blasted, the degree of fragmentation and the muck pile configuration is determined, as are the effects on cost and productivity of all subsequent operations. The cost of managing oversize material, including secondary handling, overloading, reduced diggability, higher load factors, extra pass loading, increased wear factors and reduced throughput rates are all opportunities for improvement. INTRODUCTION Having visited many mine sites, customers are asking about the end to end mining value stream from loading to the crusher and how to measure the cumulative effects on each part of the mining value chain. All too often improvements with the drilling and blasting may impact fragmentation but do not improve the diggability so the net change on cycle times or fill ratios is perceived to be negative at the point of loading but they may have a measured improvement going through the primary crusher. This makes it imperative to measure performance at each segment of the overall cycle and not just to the crusher but thru it. The mine material process originates with solid rock, in-situ, and progresses to the output of the primary crusher. Once the material has passed the primary crusher the fragmentation size will be fairly consistent and promote consistent throughput of the plant or mill. In late 2015 a team was conducting a reassessment visit to a mining site where we had conducted the original assessment the previous year. Though many recommendations had been implemented some had been so recent they had not resulted in the expected improvements. Several of our discussions kept returning to the impact fragmentation has to both the individual components of the mining cycle but also the effects compounded throughout the end to end process. Let’s move on to the big picture before we zoom in on any specific operation. To get from native solid rock in the ground to a concentrate or a saleable rock product we have the same steps from one end of the chain to the other. We start with a good geological understanding of the rock type, characteristics and structure to design a program to drill and blast the rock. The height of the bench is relevant to the annual production requirements and the specific digging equipment models best sized to make that production possible. The equipment selection influences the bench height which has a minimum and maximum hole diameter to maintain a safe blasting operation. The diameter of hole burden and spacing all contribute to a good distribution of explosives in the rock mass that maximize the fragmentation and preconditioning of the rock when blasted. The timing and sequencing of hole initiation will yield a fragmentation ratio and diggability factor. Fragmentation size adjustments will change the meters drilled per cube and the explosives consumption will change accordingly. Drill cost is measured by meter drilled so a direct relationship exists between cost and fragmentation sized achieved."

Jan 1, 2017

By Dianne M. Lapierre

Mining firms in Canada are increasingly incorporating the social and environmental interests of their stakeholders into their projects in an effort to become more sustainable. Such initiatives have included negotiating Impact and Benefit Agreements (IBAs) directly with would-be impacted, often aboriginal, communities near resource developments in the Canadian north. Why does a mining firm take on this extra time-and cost-intensive initiative when governments and regulatory measures are in place to address social and environmental issues? Past research has paid little attention to the corporate rationales for IBAs. Based on document review and interviews with mining executives, this study investigates the rationales of mining firms that ?over-comply? with legislative requirements by negotiating IBAs or similar types of agreements with communities. The results indicate that mining firms increasingly recognize IBAs as an intrinsic part of the permitting process. When queried, executives regularly identified the negotiation of agreements as ?the right thing to do?. While this response could be read in ethical terms, a commercial rationale is also clearly present. By building strong relationships with nearby communities, addressing community concerns, and directing benefits to local people, all of which are explicitly achieved with an IBA, mining firms are maintaining their long-term financial viability, thus their sustainability, within an evolving industry.

May 1, 2008

By Reino Kurppa

The Pyhäsalmi mine of the Outokumpu Co. is located in central Finland (Fig. 1). The deposit was discovered in the autumn of 1958. Construction of the mine was started a year later, and production began on Mar. 1, 1962 (Fig. 2). At present, 750,000 metric tons (mt) of ore and a nearly equal amount of country rock are mined annually. Slightly over one-half million tons of various concentrates are produced per year, of which 85% is pyrite concentrate, 10% zinc concentrate, and 5% copper concentrate. The pyrite concentrate is treated in the company's pyrite smelter,1 yielding elementary sulfur, sulfur dioxide, and iron-oxide cinders, as well as electric power. Thus all the sulfides, totaling 75% of the ore, are of economic value. This is a fact which had a bearing on the development of the stoping method. GEOLOGY The ore is of breccia type containing fragments of country rock of varying sizes. It is coarse-grained pyrite ore containing sphalerite and chalcopyrite as a matrix between the pyrite grains. Only small amounts of pyrrhotite have been observed in certain marginal parts of the orebody. The ore averages 0.85% Cu, 3.0% Zn, 38% S, and 33% Fe. The orebody extends from the surface down to at least 500 m, which is the lowest level from which present information has been obtained. Horizontally, the orebody is 650 m long. It is 75 m wide at its central part, narrowing towards the ends (Fig. 3). At a depth of 115 m, the orebody suddenly narrows down to a thickness of 25 to 30 m. In the northern part of the orebody, the dip is 50° to 70°, but elsewhere it is almost vertical (Fig. 3).

Jan 1, 1969

By E. Farrokh

CSM and NTNU models are among the most commonly used models in TBM performance evaluation. Due to increasing application of TBM in different tunneling conditions, modification became necessary for these models. Sensitivity analyses on these two models indicate that both models are very sensitive to machine characteristics. Analyses performed on CSM database for cutter load and penetration rate prediction indicate while the r-square of the CSM model is reasonably high for the predicted cutterload, the r-square value for the penetration is low. In order to increase prediction capability of CSM model for penetration rate the model was reevaluated using non-dimensional analysis and the original database of Colorado school of mines. NTNU model is evaluated using Monte Carlo simulation and regression analysis. The results of analyses indicate that the majority of the variation of the penetration in NTNU model can be explained by only three parameters. This might indicate that the effects of other factors are overshadowed and it is worthy to reevaluate NTNU model using original database and more updated statistical methods to avoid overlapping of different parameters correlations.

Feb 23, 2014

By Rayner B

Five wells have been drilled in the Basker/Manta Block of VIC/P19, Gippsland Basin, resulting in sub-economic Intra-Latrobe Group oil and gas discoveries at Basker-1 and Manta-1. A total of 21 individual hydrocarbon bearing sandstones were intersected by the two wells. These reservoir sand bodies were deposited by fluvial processes in a lower coastal plain environment. The modelling of sand body orientation and geometry is a critical component in the evaluation of the two accumulations. Seismic resolution of the thin (average 2 m to 5 m) sand bodies is inadequate for mapping their orientation and distribution. Dipmeter data has been successfully applied to the problem of orienting the sand bodies using FMS images acquired during the drilling of Gummy-1 and reprocessed HDT data from Basker-1 and Manta-1. Prediction of lateral extensiveness (geometry) of individual sand bodies has also been attempted. Interpreted palaeocurrent direction from all three wells is dominantly from the NW to the SE. Reservoirs in the Manta-1/Gummy-1 area are interpreted to be predominantly channel sands, deposited by relatively low sinuosity streams. As such they would tend to have a laterally extensive, elongate geometry. Sand bodies deposited in the Basker-1 area show a predominance of laterally accreted cycles deposited by meandering streams. Channel geometry may then be limited in the downstream/upstream direction by internal permeability barriers such as clay plugs.

Jan 1, 1992

By Fumiatsu Sato

In recent years, an increasing number of urban soil contamination cases have been found during redevelopment of former factory sites. Hydroclassification technique, separating heavily contaminated fine soil particles from contaminated sites, is one of the economical remediation techniques for contaminated soil by heavy metals, but the separated fine soil particles are generally landfilled because of the difficulty in removing strongly adsorbed heavy metals on them. In the previous study, the authors have investigated the mechanism and the optimum condition of chlorination-volatilization technique to eliminate heavy metals from inorganic waste and found it was needed to heat up around 1273K. In this paper, a new remediation technique for lead contaminated fine soil particles is proposed. This technique is composed of chlorination and subsequent warm water extraction. In the chlorination step, water-insoluble lead complex is chlorinated to be water-soluble lead chloride without volatilization, by heating the soils with MgCl2-CaCl2-KCl salt mixture at relatively low temperature. By subsequent warm water extraction, lead chloride is leached out. Effects of chlorination conditions, such as time, temperature, composition of the salt and added salt ratio, on lead behavior were investigated. It was proved that lead concentration could be reduced below Japanese environmental standard.

Jan 1, 2006