Search Documents

By Hongli Wen, Guangkun Shen, Qiong Deng, Xuling Chen, Min Gan, Xiaohui Fan

"In this research, pyrite cinder which contains 53.51% Fe and 0.54% Pb was processed by magnetic roasting separation to obtain a concentrate with 64.62% Fe and 0.56% Pb. The concentrate was then leached with hydrochloric acid to remove lead. Several technological parameters which may influence the removal efficiency were investigated: the mass fraction of hydrochloric acid, pulp density, the leaching time and temperature. On the conditions that the mass fraction of hydrochloric acid of 5%, pulp density of 30%, the leaching time of 30 minutes and leaching temperature of20°C, the lead content in the concentrate was reduced to 0.19%. The product was suitable for agglomeration and pelletization. Through the analysis of the lead distribution and phase change during the whole process, the mechanism of lead separation from pyrite cinder was analyzed.IntroductionPyrite cinder is rich in iron, which defines its most extensive and effective use as raw materials for iron making. However, some pyrite cinders contain much non-ferrous metals, which is detrimental for the iron making process. Lead, one of the harmful elements, will destroy the blast furnace lining. Besides, it causes pollution of the environment[1]. Therefore it is necessary to remove excessive lead before entering the blast furnace. To separate the lead from pyrite cinder, much research was done, including flotation, high temperature evaporation and leaching. High temperature evaporation consumed too much energy. The flotation was difficult to obtain high- grade iron ore concentrate[2]. Majority of the leaching was direct leaching of pyrite cinder, which was also difficult to get high-grade iron ore concentrate[3]. This article explored the magnetic roasting method to get high-grade iron ore concentrate, acid leaching method of the concentrate to remove excessive lead, providing guidance for the efficient utilization of pyrite cinder."

Jan 1, 2013

By Alexander L. Holley

THE Pernot system of rotating and withdrawing the hearth of a Siemens regenerative gas furnace for the production of Martin or open-hearth steel, is, perhaps, the most conspicuous of the several improvements which have lately been made in the steel manufacture. These several improvements in the open-hearth plant are not combined in any existing works, but most of them will be combined in not less than three works now erecting in the United States; and it seems probable that their joint result will not only reduce the cost of products of ordinary grades to Bessemer rates, but that it will produce new and better grades of products. The open-hearth steel furnace and its operation are so generally understood that but a few words of general description are necessary. The ordinary furnace is not unlike the common reverberatory puddling furnace, except that an intense, uniform, and controllable temperature is maintained by the Siemens gas regenerative system. The materials. employed are various : melted or unmelted pig with ore, and with or without scrap; pig iron purified from silicon and phosphorus, with or without scrap; pig iron and scrap, melted together in a cupola, or charged hot or cold, together or separately, into the steel furnace; a pig-iron bath, and hot or cold steel or iron scrap, direct sponge or Catalan or puddled blooms charged into the bath. The operation is, to a greater or less extent, according to the nature of the materials used, a desiliconization and decarburization of the pig or other crude iron, and its dilution by already purified materials. Manganese is employed at the end of the operation to remove oxide of iron and silica, a regulated amount of manganese remaining in the product. Figs. 2 and 3, Plate IV, represent the hearth and roof of the Pernot furnace; Fig. 1 shows, in cross section, the general arrangeent of open-hearth plant with Pernot furnaces, as generally designed by the author, and now building at two works. The engrav-

Jan 1, 1879

By Robert C. Meaders, Arthur R. MacPherson

Many attempts have been made to eliminate most of the crushing plant and all the grinding plant in the process of ore beneficiation by substituting a combined crushing and grinding unit which could take coarsely crushed ore and reduce it to a fine size in one unit. This unit normally would have no other grinding media than the ore itself. This is true autogenous grinding, as we understand it today, and should be clearly distinguished from pebble mill grinding, where pebbles are substituted for steel balls to grind a ball mill size feed. To compete in efficiency with normal methods of crushing and grinding, the autogenous mill must use less labor and steel to produce an equivalent product at equal or lower power consumption. In general terms, a unit to perform these functions must have means to crush the ore to fine sizes and to then further reduce the crushed pieces by grinding. In other words, to do efficient autogenous grinding, there must be a proper balance established between crushing and grinding rates. There is not much point in crushing at too fast a rate if the grinding means are not present to reduce the small particles to the required product size. The crushing means used in an autogenous mill are impact forces of two kinds, namely, (1) the rock travelling at high speeds striking the shell, and (2) the lifters travelling at high speeds striking the rock. Grinding is probably effected in a manner equivalent to pebble milling.

Jan 9, 1964

By Kenton E. McElhattan

Financial analysts have often called National Mine Service Co. the only "pure play" company to the mining industry, meaning that an investment in NMS is an investment in the mining industry. As a leading manufacturer and supplier to the industry, National Mine Service does enjoy a close and direct relationship with mining. It is the only independent company that offers products and services that include mining machinery, health, safety, instrumentation, mine supplies, and reconditioning services for hydraulics, electronics, and machinery. But what is a positive relationship in periods of economic upturn can be eauallv as negative during the downturns. In fact, National Mine Service has felt the resounding blows of the current recession in the mining industry. Two-Fold Strategy Rising unemployment, corporate losses, bankruptcies, and mine closings in particular have directly affected NMS. But the company embarked on a strategy several years ago that included a two-fold approach to becoming less dependent upon the vagaries of the US coal industry. One strategy was to develop additional products and services for other mineral industries such as potash, trona, and salt and, where possible, apply the technology developed for the mining industry to industrial markets. The other strategy was to become a more international company. The objective was to make export sales a minimum of 10% of total corporate sales. Even today, NMS believes this is a good strategy as opposed to diversifying because its expertise is in mining, not in other areas. A review of NMS's fiscal 1982 annual report indicates that the company's strategy did begin to pay off. 1982 was a turnaround

Jan 2, 1983

By V. T. McLemore

"Production of industrial minerals remains important to the rural economy of New Mexico. In 2014, some 240 mines were registered in New Mexico, including 25 industrial mineral operations and 189 aggregate operations. New Mexico leads domestic production of potash, perlite, zeolite, and travertine. Other production includes aggregate, humate, pumice, gypsum, salt, common and fire clay, scoria, limestone, fly ash, cement, magnetite, silica, and decorative stone. New Mexico has potential for additional production of industrial minerals. One company is exploring for garnet. Cretaceous black sandstones in the San Juan Basin have drawn interest for titanium, rare earth elements (REE), and zircon. Other REE deposits are being explored. REE-Th-U veins are found in the Gallinas, Capitan, and Cornudas Mountains and Laughlin Peak-Chico Hills. Recent exploration has occurred for beryllium in the San Mateo Mountains, Iron Mountain, and Victorio districts. Companies also are examining High-Ca limestone and High-Mg dolomite for potential development. Aggregate continues to be important in urban areas and along highways. INTRODUCTION Industrial minerals and rocks are literally the building blocks of our way of life and they are an exceptionally diverse and vital group of raw materials that underpin almost all aspects of human activity, infrastructure, and standard of living. Industrial minerals and rocks are used in the manufacture of many products, from ceramics to plastics and refractories to paper. Although industrial minerals permeate every aspect of daily life, their presence and their role are typically invisible. A widely used definition of industrial minerals and rocks is “any rock, mineral, or other naturally occurring substance of economic value, exclusive of metal ores, mineral fuels, and gemstones: one of the non-metallics” (Bates, 1975). This definition includes the important construction materials sector as well as specialized industrial minerals, but complex interactions between consumer industries produce a number of apparent anomalies to this definition. Some metals are included as industrial minerals because their use is industrial rather than as a metal. Sulfur is now predominantly extracted as a by-product of cleaning natural gas, one of the world's major energy fuels. Production of industrial minerals has been and remains important to the rural economy of New Mexico. Industrial minerals constitute nearly 40% of the more than $2.8 billion generated by mineral production in New Mexico in 2013 (Table 1, see APPENDIX). In 2015, some 240 mines were registered in New Mexico. This total includes 25 industrial mineral operations and 189 aggregate operations. New Mexico leads domestic production in potash, perlite, zeolite, and travertine. Other industrial minerals production from New Mexico includes aggregate, humate, pumice, gypsum, salt, common and fire clay, scoria, limestone, fly ash, cement, magnetite, silica, and decorative stone. Additional production statistics are in Harben et al. (2008). Major industrial mineral districts are shown in Figure 1."

Jan 1, 2016

By B. J. Scheiner

The Bureau of Mines, U.S. Department of the Interior, has investigated the use of rheology to provide insight into the mechanism of flocculation. A technique developed by Tattersall has been modified and used to explain the flocculation of calcium montmorillonite with polyethylene oxide. The results indicated that there are two types of bond systems operating during the flocculation sequence. Also, flocculation results are highly dependent on the shear rate and the amount of polymer added.

Jan 1, 1989

By D. J. Carney, R. L. Stephenson

M. O. Holowaty (Inland Steel Co., Chicago)—Messrs. Stephenson and Carney should be commended on the presentation of this very interesting paper. They have introduced new ideas on sampling of sinter and have thereby made a valuable contribution to the qualitative evaluation of sinter. The paper undoubtedly presents a novel approach to the problem of sinter sampling and this is to be regarded as its main value. Sampling of sinter from the pallets prior to the discharge is by no means new. This sampling procedure was used in the past by Philbrook; Hamilton and Ameen and others. The sampling basket used by the authors of this paper, however, permits one actually to obtain a good sample of the sintering mixture. The basket which can also be described as a removable pallet goes then through the entire process of sintering and thus offers a sample which is positively representative of the batch in question. The authors' method of evaluating physical properties of sinter seems to be not altogether clear, however. It is felt that the following points should be clarified: I—In the section describing the shatter test the authors state that a 5-lb sample was used in the actual tests. There is no mention of the initial size of sinter particles used and the method of obtaining this 5-lb sample from the sinter cake weighing about 100 to 120 lb. It is also surprising that the sample was dropped from a height of 3 ft instead of the conventionally used 6 ft. Unfortunately there is no mention of the number of drops to which the sample was subjected. 2—The tumbler test used by Messrs. Stephenson and Carney in testing the samples of iron ore sinter was performed in a standard ASTM coke tumbling drum. The drum measures 3 ft in diam and is equipped with two 3-in. lifter bars. The distance of fall in this testing drum is identical with the distance used in the previously described shatter test. The number of drops in the tumbling drum is approximately double the number of revolutions. The basic difference then between the drop-shatter test used by Stephenson and Carney and the tumbling test seems to be the number of drops to which the sample is subjected and the abrasive action to which the sinter particles are exposed in the rotating drum. In any case, the choice between the shatter test and the tumbler test seems to be only a matter of taste and convenience. 3—The authors of the paper state that "in order to insure getting results that were representative . . . the entire sample obtained by means of the sampling basket was used as the starting material for the tumbler test. If the sample broke in pieces, all the pieces were used regardless of their size." The initial size of the material is known to be a very important factor, influencing seriously the final size of the particles. This should be particularly important in case of hard sinters. It seems also very troublesome and inconvenient to charge 12-in. cubes of sinter weighing about 100 lb into the testing drum. This could be eliminated by taking a standard fraction of somewhat smaller particles.

Jan 1, 1954

By A. P. E. Dirige

In order to maximize the recovery of ore and to save on costs in undercut mining, backfill of low cement content is used to fill the mined out excavations. This backfill mass is supported by a sillmat structure cast from cemented backfill of very high strength. The stability design of sillmats must be carefully studied to provide very effective, safe and economic mining operations. This paper presents a methodology and procedures for sillmat design based on three engineering modeling approaches: analytical, numerical and centrifuge modeling. Application of the design approach is demonstrated from a design study conducted for an underground gold mine, aimed at minimizing backfill binder content and at producing cost efficient paste fill recipes for sillmat construction. Application of the engineering design recommendations was projected to result in substantial annual cost savings to the mine operation.

May 1, 2007

By Feng Ningchuan, Guo Xueyi, Tian qinghua, Liang Sha

"In this study, copper adsorption by orange peel which was chemically treated with sodium hydroxide was investigated. The morphological and chemical characteristics of the adsorbent were evaluated by spectroscopy and N2-adsorption techniques. Equilibrium isotherms and kinetics were obtained and the effects of solutions pH, adsorbent concentrations and temperature were studied in batch experiments. Equilibrium was well described by Langmuir and Freundlich isotherms and kinetics was found to fit pseudo-second order type adsorptions kinetics. According to the Langmuir equation, the maximum adsorption capacities (qm) for Cu(II) was 50.25 mg·g-1 at pH 5.3. With the temperature increased from 16 to 60°C, copper removal decreased. The loaded adsorbent was regenerated using HCl solution and could be used repeatedly at five cycles with little loss of adsorption capacity. The results show additional chemical treatment of the adsorbent by NaOH, is favor of improving the adsorption capacity. Introduction Increased use of metals and chemicals in manufacture industries has resulted in generation of large quantities of effluent that contains high level of toxic heavy metals and it poses environmental-disposal problems due to its non-degradable, persistence nature and accumulation throughout the food chain [1, 2]. Copper is known to be a commonly used heavy metal. This metal, which found many useful applications in our life, is very harmful if charged into natural water resources and may pose finally a serious health hazard. Many methods, such as chemical precipitation, ion exchange, reverse osmosis and adsorption, etc., have been used for heavy metal ions removal from various aqueous solutions. In recent years, there has been considerable interests in use of biological materials including algae, bacteria, fungi, agricultural by-products and residues as adsorbents to remove toxic metals from aqueous solutions by adsorption [3-8]. Adsorption process has been extensively used to remove copper from aquatic medium using low cost adsorbents such as peanut husks [9], plant materials [10] and cellulose materials [11]. Among them, agricultural by-products and biomass are relatively cheap and show very high adsorption capacities. However, to apply untreated agricultural by-products as adsorbents has the disadvantages such as low adsorption capacity, high chemical oxygen demand (COD) and biological chemical demand (BOD) as well as total organic carbon (TOC), due to the release of soluble organic compounds contained in the plant materials such as lignin, tannin, pectin and cellulose, into the solutions [12-14]."

Jan 1, 2008

By L. A. Vermeulen, D. D. Howat

The use of pebbles as the medium in the grinding of quartz gravel in a laboratory mil provided experimental data that were used to quantify the relationships between the feed rate of ore to the mil, the fineness of grind of the product, and the wear rate and consumption of the grinding medium. Fineness of grind is expressed as the inverse of the harmonic mean size, a quantity that is calculated from data obtained by sieve analyses. The commonly used criterion for fineness of grind (the percentage of material smaller than 75 µm in the mil product) is shown to corelate approximately linearly with the inverse of the harmonic mean size. An increase in the feed rate was found to cause the harmonic mean size of the product to increase linearly, Le. the relationship previously found for metalic grinding media is applicable to al grinding media, irespective of shape or composition. Simple expressions for the consumption and wear rate of pebbles are derived from the experimental data, and are shown to be functions of the feed rate. The expression for wear rate is a monotonicaly increasing function, while that for consumption is a hyperbolicaly decreasing function of the feed rate. In contrast, a linear relationship was found between the rate of wear of the grinding medium and the rate production of fines. The expressions that were previously developed in relation to the use of metalic grinding media are shown to be equally applicable to pebble milling.

Jan 1, 1988

By T. P. Meloy

Media mills operate by having energy transferred to the media which in turn grinds the feed material in a packed bed. Regardless of the mill type, the media energy density per unit surface area is constant. Since for optimum grinding conditions, both peak pressures and particle number of the bed depth are constant, the frequency of energy input is inversely proportional to feed size. As the particle size decreases the voles energy density increases linearly necessitating cooling in stirred mills. Grinding finer particles therefore, requires moving from rotary to vibratory mills, and the finest, the stirred mills.

Jan 1, 1987

By B. T. Mirabile, D. Tang, Y. Luo, S. S. Peng, C. T. Holland

Knowledge of local coal mine roof geology is critical to the design of a safe and suitable mine structure. An automated drill control and data collection system has been designed for a J.H. Fletcher twin-head roof bolter. Drilling parameters collected during the drilling process can be used to interpret geologic features intercepted in the mine roof. The drill and data collection system have been tested in both laboratory and underground settings. Visualization of certain drilling data has shown good correlation with geology drilled. A quantitative prediction model was developed using drilling parameters examined with data visualization. The quantitative model was tested using laboratory drilling data.

Jan 1, 2004

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

7.1 INTRODUCTION Subsidence measurements include surveys of surface and sub- surface movements and measurements and monitoring of surface structural damages. In this chapter the most commonly employed methods are discussed. 7.2 MEASUREMENT OF SURFACE MOVEMENT Surface movements involve two basic components, subsidence and displacement. The other five components (i.e., slope, curvature, strain, twisting, and shearing) are derived from the two basic components. Since all measurements are geometrical, they can be measured by common surveying techniques. 7.2.1 MONUMENTS The first step is to select the types of monuments or surveying stations. Various types of monuments have been employed. The simplest one is a paint mark on the pavement or concrete slab, although this should be discouraged because it is easily affected by artificial or environmental factors. Others use steel or wooden rods, 2 to 3 in. in diameter or square by 2 to 5 ft long, driven all the way down, flush with the ground. Both types of-monuments have no provision for frozen ground heave and both are tampered with easily. A more elaborate type is shown in Fig. 7.1 (O'Rourke et al., 1982). A rebar or iron pipe, 2 in. in diameter by 6 ft long is driven down to nearly flush with ground surface. The top 4-ft section of the hole around the pipe is enlarged to 1 ft in diameter and grouted with concrete. The most sophisticated type of monument is shown in Fig. 7.2 (Conroy and Gyannaty, 1983a). It consists of two hollow steel pipes. The inner I-in. pipe, 10 ft. long is enclosed by a 2-in. pipe at the upper 5-ft. interval. The gap between pipes is filled with foam to isolate the inner pipe from external environmental effects. The bottom of the inner pipe can either remain open or be sealed with a cap, depending on whether the ground is dry or wet. 7.2.2 MONUMENT ARRANGEMENT AND SURVEY LINES The monuments are installed strategically to form survey lines. Three basic types of monument arrangements are shown in Fig. 7.3. Figs. 7.3a and 7.3b are for single and multiple panels respectively; Fig. 7.3~ is mainly for research purposes with multiple survey lines both in longitudinal and transverse directions. This is extremely useful for defining the distributions of ground deformation, as shown in Figs. 2.10 and 2.11. Basically there are two types of survey lines: the whole basin survey line which extends across the panel width or length (e.g., lines R, R, in Fig. 7.3 a&b), and the half basin survey line which covers approximately half of the panel width or length (e.g., lines R, F in Fig. 7.3 &b). Survey lines are generally straight and linear. They should be located on the major crosssections of the subsidence basin. Survey lines must extend beyond the edge of the opening for a sufficient distance so that the edges of the subsidence basin can be determined accurately. The minimum distance from the edge of the opening must be [ ] where h = mining depth, [ ] = angle of draw, and [ ] = 5 to 7 times monument spacing for whole basin surveys, or 8 to 10 times the monument spacing for half basin surveys. There must be at least two controlling monuments at each end of each survey line. Controlling monuments must be located beyond the influence of underground mining. The spacing of the monuments ranges from 15 to 200 ft. The UK National Coal Board (NCB, 1975) recommended a spacing equivalent to 0.20 of the mining depth. Peng and Geng (1982) recommended that the maximum monument spacing be dependent on mining depths as follows:

Jan 1, 1992

By B. H. Wadia

El presente texto describe las propiedades físicas y químicas de la plata, el proceso de extracción y refinados, las dos etapas de conversión, copelación, refinación electrolítica, producción de la plata esterlina, métodos de cianuración, lixiviación clorurante y volumen de producción.

Jan 1, 1984

By Gustavo De la Torre Guzmán

En planta concentradora – Cerro lindo en su afán de consolidarse como una operación de categoría internacional, mantiene el enfoque de excelencia operacional gestionando de forma sistemática seguridad, salud ocupacional, medio ambiente, costos, productividad, calidad y confiabilidad además de nuestro proceso productivo. Para lograr el desempeño de categoría mundial y ser catalogados como tal, implica también usar la capacidad total del área (procesos, tecnología y talento humano) para implementar estrategias de optimización que garanticen la efectividad de las operaciones, para el éxito del proceso.

Sep 1, 2017

By A. K. Mukhopadhyay

[The mechanical status of a mine ventilation fan can be monitored effectively through vibration analysis. An expert system can be an effective tool in fault diagnosis for a variety of equipment. Computers have made it possible to implement an expert system to analyze the data for correct and appropriate diagnosis. In addition, vibration analysis can provide important information oil the condition of the machine. This paper discusses an approach for an expert system to determine on vibration analysis, practical problems that can occur with a fan. The frequency of the vibration is the only characteristics considered in the analysis, although other variables are discussed in the paper. Finally, a simple computer program, written in Turbo Prolog, is presented. A friendly query system, menu operation and a disk-resident separate knowledge base are a few of the salient features of this system.]

Jan 1, 1997

By E. V. Lilford

The South African Minerals Development Act (?the Act?) has been promulgated and will come into full force and effect once it is gazetted. Thereafter, all Old Order mineral rights will have to be converted into New Order mineral rights within a 5-year period, probably by the end of 2008. The conversion of rights will be achieved only with the demonstrated inclusion of empowerment groups in the conversion applications. In addition to the Act, the first draft of the proposed Royalty Bill (?the Bill?) was released during the week beginning 17 March 2003. Comments on the Bill?s contents had to be submitted before 30 April 2003. The contents were to be considered in terms of applicability and acceptability to the South African minerals industry, where after proposed comments and suggested amendments were to be submitted to the relevant State Treasury office. Specifically referring to the Bill, the general response from the industry is one of concern. Since any royalty is tantamount to a tax, the general feeling is that the current mining taxation rates are already internationally competitive and to increase these effective rates, notably at differing rates depending on commodity type, will have an adverse impact on the South African mining industry. A number of these impacts can be mitigated to some degree, depending on the flexibility of the State to address the major concerns.

Jan 1, 2003

By Donald G. Foot, Jeffrey D. Mckay

Flotation columns have been readily accepted for use in most sulfide flotation plants: however, recently columns are being used in many other areas. Recent improvements in design methodologies have overcome many operating problems and led to improvements in metallurgy. In addition. Physical improvements in column design have simplified their operation while leading to better control. The Turbo-Air External Bubble Generator has provided a method for bubble size control and variation in air holdup and carrying capacity. These have enabled commercial operations to improve grades and recoveries by optimizing performance.

Jan 1, 1989

By Janice Zinck, Ian London

In recent years, the secure supply of critical and technology metals has become increasingly important tomajor industrialized economies that seek to sustain their industrial base and develop advanced technologies, such as clean energy. Canada, with its significant reserves of rare earth element (REE) and other metals, has an opportunity to supply some of the global demand for these materials. However, to transition from promising mineral deposits to marketable products, investment in strategic research and development (R&D) and expertise is needed to address the complex technological challenges around the production, separation and processing of these metals, and to better understand the global market for these key commodities. To this end, in its April 2015 budget, the Government of Canada committed to invest $23M over 5 years to accelerate production of REE and chromite/ferrochrome. The goal of this program, developed in close association with industry, is that Canada contributes a sustainable supply of REE to the global market. The research and development program will provide the technological capacity to establish a Canadian REE industry. This paper will discuss REE R&D advances achieved in the first year of the program in areas of mineral characterization, beneficiation, leaching, separation and environmental management and will highlight the Canadian model of collaboration where industry (e.g. prospective producers, technology companies), government, academia and other stakeholders work closely to ensure that the R&D is targeted, innovative and effectively deployed and commercialized.

Jan 1, 2016

By R. D. Ellison, D. K. Shukla, D. E. Stephenson

Seals for man-made penetrations into or nearby nuclear waste repositories require several unique capabilities not common to seals for conventional underground activities. Design criteria include long functional use, extremely low permeabilities of the seal zone (including adjacent disturbed rock), and the potential for retarding radionuclide travel. This paper summarizes comprehensive seal programs being conducted by D'Appolonia for the Office of Nuclear Waste Isolation (ONWI) at Battelle, Columbus. The program schedule requires the first detailed conceptual design for a bedded salt site to be completed in 1982. Conceptual designs for other host media will follow as site exploration data becomes available. The design program is supported by a variety of office, laboratory, and field activities being conducted by ONWI subcontractors. An example is provided to illustrate the variety of efforts directed toward determining the extent of disturbance adjacent to penetrations as a result of in-situ and excavation methods. Also, the current "working design" for the shaft and tunnel seal system at the candidate Los Medanos thick salt site in southeastern New Mexico is presented.

Jan 1, 1981