Search Documents

By Shahriar Vandani, Andy Herlache, Andrew Bro, Wei-Yu Chen

"The Presidio Parkway Project will reconstruct approximately 1.6 miles (2.6 km) of highway, including seven new bridges, three new cut-and-cover tunnels, and a new undercrossing connecting the Golden Gate Bridge to the City of San Francisco, California. The project site is approximately 5.6 miles (9 km) from the San Andreas Fault, capable of producing magnitude 8 earthquakes. Seismic hazards include strong ground shaking, soil liquefaction, ground settlement, and lateral spreading. The Main Post Tunnels (MPT) are two parallel cut-and-cover concrete tunnels approximately 1100 feet (335 m) long. The MPT site underlain by loose sandy soils susceptible to liquefaction and lateral spreading. Excessive racking and permanent displacement due to lateral spreading are identified as the main seismic vulnerabilities. Analyses showed that without ground improvement, tunnel racking of over 5 inches (13 cm) and permanent lateral tunnel displacement of up to 15 feet (4.6 m) could be anticipated. Cement Deep Soil Mixing (CDSM) is proposed to mitigate slope displacements and increase lateral stiffness of the foundation materials to reduce tunnel racking. A series of 2-D fully dynamic time domain analyses were performed to evaluate the performance of CDSM, confirm that performance criteria are met, and optimize the CDSM geometry and replacement ratio. The use of CDSM reduced the permanent tunnel displacement from over 15 feet (4.6 m) to less than 1 inch (2.5 cm). Tunnel racking was also reduced significantly. The adopted analytical approach presented herein can be considered for future tunnel design projects in seismically active areas.Introduction The Main Post Tunnels (MPT) are an integral component of the Presidio Parkway project which will replace the existing facility with a new multi-lane roadway between the Golden Gate Bridge and the City of San Francisco. The MPT are two parallel cut-and-cover concrete tunnels approximately 1100 feet (335 m) in length. As shown on Figure 1, the project site is located in a seismically active area, about 5.6 miles (9 km) east of the San Andreas Fault and 12.5 miles (20 km) west of the Hayward Fault. The San Andreas Fault can generate magnitude 8 earthquakes while the Hayward Fault is capable of producing magnitude 7.3 earthquakes. The design Peak Bedrock Acceleration (PBA) is 0.46g for the upper level design earthquake. The project alignment is shown on Figure 2."

Jan 1, 2014

By Rafal Misa

In order to prevent the formation of mining damage or to reduce its reach, it is advisable to look for technical solutions which would enable effective protection of construction sites from the impacts of underground mining. So far, other authors have mainly focused on developing methods of securing construction sites in order to minimize the damage resulting from underground mining; the issue of geotechnical methods for protecting buildings against mining damage has not been thoroughly covered in those articles. It should be noted that there are relatively few publications directly related to this issue, nor are there practical examples of geotechnical protection. In this paper, a geotechnical solution available for securing building structures is discussed. Trenches presented in this research reduce the size and range of mining deformation. The results of numerical modelling for sample protective solutions, aimed at reducing the impact of mining activity on the terrain surface under various conditions, are presented. The calculations were performed with the aid of the Abaqus 6.10-2 software, based on the Finite Element Method.

Jan 1, 2014

By Agne Rustan

This paper is intended to give a summary of the first ten Symposia on Rock Fragmentation by Blasting where the symposia activities were governed by a Steering Committee replaced at Fragblast 2 by an International Organizing Committee (IOC). At Fragblast 9 the name was changed to Fragblast International Organizing Committee (FIOC). Eighty four pages of statistical data about Fragblast 1-10 is documented on the Fragblast Website (ISEE.org).

Jan 1, 2014

By X. -G. Chen, A. M. Nabawy

A novel manufacturing technique for Al-TiB2 nanocomposites has been developed, in which TiB2 nanoparticles were incorporated into liquid aluminum under mechanical stirring and in the presence of a K2ZrF6 flux-wetting agent. The microstructure of the Al-TiB2 nanocomposites was studied using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The microhardness test was conducted to investigate the strengthening effect of TiB2 on the aluminum matrix. The TiB2 nanoparticles were successfully incorporated and dispersed into the aluminum melt in the presence of the K2ZrF6 flux during mechanical stirring. In the as-cast microstructure, most nanoparticles segregated in the interdendritic regions as a result of particle redistribution during solidification. The addition of 2, 5 and 10 wt% TiB2 nanoparticles increased the composite hardness by 60, 90 and 150% respectively when compared to commercial purity aluminum, indicating that the TiB2 nanoparticles imposed a significant strengthening effect on the aluminum matrix. The role of K2ZrF6 flux agent on the incorporation of nanoparticles into aluminum melt was discussed.

Jan 1, 2014

By P. K. Rozakeas

It has been experimentally demonstrated that the application of electrokinetic techniques in the continuous flow of coal-water suspensions within a helical anode-cathode pipe geometry effectively causes a significant reduction in the wall shear stress. This reduction in the frictional force at the cathodic pipe wall surface is attributed to a decrease in the concentration of coal particles in this flow region caused by the migration of negatively charged coal particles towards the anodic surface(s). The disadvantage of flow-intrusive geometries is the reduction in effective flow area as well as an increase in frictional surface area caused by the placement of the anode(s) within the flow region. Experimental data is presented for a non-intrusive helical anode-cathode geometry embedded in the pipe wall which shows that a reduction in pumping energy of approximately an order of magnitude is possible. A sample of sub-bituminous black coal fines having a mean particle size of approximately 17 microns was used to prepare coal-water suspensions with a solids concentration of 50%(w/w). The practical and economic implications of this work relate to an enhanced method of long distance transportation of slurries in pipes as well as an alternative technique for continuously separating solid-liquid suspensions.

Jan 1, 2014

By Michel Brissette, Shaheer Sanuri, Veroljub Mihajlovic

"The main purpose of geometallurgy is to improve the mine planning by mapping hardness and throughput into the mine block model using geostatistics to eliminate the large production fluctuations caused by the ore hardness variability coming from different parts of the pit. However, not all grinding testwork available commercially can be applied to geometallurgy because of large amount of sample required and the associated cost per test. Geometallurgy is now being used in designing grinding mill but as the mining project progress, the accuracy of engineering must improve from 30-35% during the scoping study to 10-15% at the bankable feasibility stage and less than 5% for Engineering Procurement and Construction Management. For SAG milling, the SAG Variability Test (SVT) is an abbreviated version of the standard SAGDesign test developed for this geometallurgical need. The same amount of ore than the original test is ground for three cycles into an open batch SAG test and then the SAG pinion energy is predicted to the standard end point of 80% passing 1.7 mm. For ball milling, a Bond Variability Test (BVT) was also developed using the SAG ground ore from the SVT. The Bond ball mill grindability (Gpb), corresponding to the average of the net grams per revolution from the last three cycles of the Bond test, is also predicted from the third cycle. The relative error for both the predicted SAG ore hardness (WSVT) and Bond Work Index on SAG Variability ground ore (Sv-BVI), in kWh/t, averaged 5.5% and 3.8% respectively compared to the SAGDesign testwork values and are within 7% and 10% respectively from plant benchmark and within 7% from the samples sent to all partner laboratories. Both tests can be continued to measure the true hardness necessary for mill sizing. This article discusses the development of these two new tests, SVT and BVT, their potential use and accuracies in any geometallurgical program."

Jan 1, 2014

By Robert Hopler

After the disbanding of the Gunpowder Trust Association in 1904, the Association of Independent Powder and Dynamite Manufacturers was formed, followed in May of 1906 by the formation of the Association of Manufacturers of Powder and High Explosives. Due to a lack of success in attracting all manufacturers to membership, these organizations did not survive.

Jan 1, 2014

By Kirsten Corin, Margreth Tadie, Michael Nicol, Cyril O’Connor, Jenny Wiese

"The recovery of base metal sulfides has been emphasized in the study of the flotation of platinum group minerals (PGMs). However, in some ore bodies such as the Platreef of the Bushveld Complex, sulfide minerals do not make up the majority of the more significant PGM mineralization. It is therefore important to develop a fundamental understanding of how non-sulfide and sulfide PGMs respond respectively to the current reagents being used in the flotation of these minerals. The interactions between platinum and palladium sulfides and tellurides with the thiol collectors, ethyl xanthate and diethyl dithiophosphate, have been studied using the electrochemical techniques of mineral rest potential and voltammetry measurements. The differences in the interaction between the two types of minerals with these reagents were of key interest. Rest potential measurements indicated stronger electrochemical interactions of the minerals with ethyl xanthate than diethyl dithiophosphate. These measurements also indicated that there are different forms of oxidized collector present on the mineral surfaces after interaction with ethyl xanthates. Voltammetry measurements support these observations and suggest differences of adsorption on Pt and Pd sulfides than on Pt and Pd tellurides. Voltammetry also showed that there was minimal electrochemical interaction between the Pt and Pd minerals and diethyl dithiophosphate."

Jan 1, 2014

By H. Zhu, Y. Sato, O. Takeda, K. Nakano

Recycling of rare earth magnet wastes is essential to insure the stable supply of rare earth resources. For the development of a novel recycling process, the removal of rare earth oxide from an off-spec alloy magnet was investigated by melting the alloy magnet at 1503 K together with fluoride flux, LiF-50 mol% NdF3 and LiF-?25 mol% NdF3-25 mol% DyF3. After melting, the separation of magnet alloy from the fluoride flux was achieved, and neither suspension of alloy in the flux nor suspension of flux in the alloy was observed. Oxygen concentration in the alloy decreased from 5000 mass-ppm to 160 mass-ppm by utilizing 1.5 times of equivalent amount of flux needed to completely dissolve the oxide. The investigated process is suitable for mildly contaminated waste such as a used (end-of-life) magnet because of its simplicity, low energy consumption and small limitation on location for operation.

Jan 1, 2014

By K. Trybalski

Facing the optimization activities, which purpose is to minimize the copper processing costs, the main sources of their occurring were presented. In this purpose, the costs analysis was performed, divided to individual standings, for one of the polish copper beneficiation plants. It was proved, that the main component of the copper beneficiation costs is energy consumption, generated mainly in grinding and classification node, particularly by operating mills. The technological system ? grinding and classification node ? in KGHM Polska Miedz S.A., ZWR region Lubin was then selected to investigation. To evaluate the grinding and classification node, the energetic factors W were proposed, calculated on the basis of the energetic-technological data of process, given by node monitoring system. The correctness of the energetic factors selection to evaluate the work of this node and their practical application in industrial conditions was experimentally proved in other technological object. The selected technological object ? grinding and classification node ? was then mathematically modeled and optimized. The calculated energetic factors were the basis to build mathematical models, identifying industrial copper grinding and classification process. The models described correlation and character of dependency between factors and energetic-technical data of the process. These were regressive and neural networks models. On the basis of factors models, the optimization tasks were determined, which purpose was to select the optimal points of grinding and classification node work. Also, the estimated economical effect, possible to achieve after introduction of given monitoring values to grinding and classification node optimization system, was presented.

Jan 1, 2014

By J. A. Maritz

Since the dawn of mining, pillars have been used as primary support to ensure stable workings. Early designs were based on trial and error, after which more scientific means developed over time. A vast amount of progress has been made, especially in soft-rock room-and-pillar design methodologies, from which hard-rock design theories developed with minor changes to constant parameter values. The commonly used Hedley and Grant method for hard rock and Salamon and Munro methodology for soft rock draw on the tributary area associated with the pillar, the width-toheight ratio of the pillar, and a back-analysed strength reduction factor. In these methods, only the vertical stress, or stress normal to the pillar influences the load applied to the pillar. This investigation considers the possible influence of shear stresses on pillars in a room-and-pillar layout in single reef planes and multi-reef environments, based on elastic numerical modelling methods. The possible shear stress poses a safety and financial risk to the design process, whereby an undersized pillar would lead to unstable working conditions, whereas oversized pillars could lead to an under-utilized ore resource.

Jan 1, 2014

By Danny Chan, Shahram Tafazoli, Nicholas Himmelman, Edmond Chow

"While wearable technology has been garnering attention in the consumer market, enterprise and industry have just begun exploring its potential applications. Since February 2014, Motion Metrics International has been working in collaboration with Vandrico Solutions Inc. to apply wearable technology to improve productivity and safety in the mining industry.This article discusses the value proposition of using wearable technology to deliver critical notifications in mining. The advantages and disadvantages of various form factors are explored. The challenges, both specific to mining and in general to wearable technology, are defined. Finally, the concept of MetricsGear, the first wearable technology platform developed for mining by Motion Metrics International in collaboration with Vandrico Solutions Inc., is described. MetricsGear is designed to notify the user with minimal distraction to keep the user focused on his or her primary task and aware of mission-critical events. This focus and awareness allows the user to work more efficiently and safely. The mining process consists of a series of intricate stages, where certain events or conditions in one stage can have a huge impact on other stages. The notification of these critical events or conditions is vital for ensuring the overall efficiency of the mining process. Critical notifications can be classified as two types: timecritical events and contextual information. Time-critical events are situations where a timely response from a responder can have a significant impact on seizing an opportunity or mitigating cost. Some human-computer interaction (HCI) experts classify notification types based on the interruption, reaction and comprehension (IRC) framework. Time-critical events are classified to have high interruption, high reaction and low comprehension due to their urgency. The responder should have just enough information to identify the crisis and react as soon as possible (Chow, 2014). For example, when a tooth is lost during shovel operation, it is necessary to recover the missing tooth before it jams the primary crusher. The consequence of missing this critical time period is a jammed crusher that can cause the mine to be out of production until the jammed tooth is extracted (Baumann, 2013). In this case, the responder only needs to see an image to confirm if the tooth is missing and information to identify which equipment and when the tooth went missing (Fig. 1)."

Jan 1, 2014

By M. McWha

Laboratory bias is a universal problem in all branches of analytical science. It results from differences in methods, techniques, equipment, and calibrations between laboratories. Notwithstanding that it is a property that can be measured by the use of standards or by inter-laboratory testing, laboratory bias remains a material issue for the mining industry. There is extensive literature and clear guidelines on measurement from the International Organization for Standardization (ISO) and its worldwide federation of national standards bodies (ISO member bodies) and from the science of metrology. ISO guides cover the manufacture and use of standards. An accessible source of literature covering laboratory quality control comes from the public health sector, particularly pathology. There is little doubt in financial reporting rules about the meaning of materiality. Public reporting guidelines are clear that material matters need to be disclosed for investors. Unfortunately there is currently no clear guidance what to do about biased assay results in mineral industry public reporting guidelines. This paper reviews the requirements for the manufacture and use of reference materials, public reporting requirements in the mining industry, and presents proposals to improve management and reporting of laboratory biases. Keywords laboratory bias, reference materials, ISO Guides, financial reporting, materiality.

Jan 1, 2014

By X. Q. Chen

According to the different characters of the middle-low grade bauxite, based on the normal flotation & reverse flotation technology, the author innovates the new technology which is named bi-flotation, it integrates the advantages of normal flotation & reverse flotation, while avoids their disadvantages. Take Henan middle-low grade bauxite as research object, according to the pilot experiment of bi-flotation technology, the concentrate A/S is 9.37 and the recovery of alumina is 80.18% by flotation separate the raw ore which A/S is only 4.19.

Jan 1, 2014

By G. J. McTeer, D. J. Rioux

Teck Metals Ltd operates an integrated zinc-lead complex at Trail, British Columbia, Canada. Since 1997, KIVCETTM flash smelting technology has been utilized for the treatment of zinc plant residues and lead concentrates. Trail Operations’ furnace uses four water-cooled jackets for bullion tapping. This paper provides an overview of KIVCET bullion tapping for the past 16 years, and discusses successes and challenges encountered with respect to operations, training, and monitoring.

Jan 1, 2014

By Nicolás Caussade

"The IMPC 2014 slogan "Optimizing Water and Energy Usage for Sustainable Mining" refers to the ever decreasing availability of fresh water and energy, which has turned out to be a crucial aspect in assuring the competitiveness of the mining sector in Chile and the Andes region in general. The concern for sustainability and the supply of water and energy is nowadays part of the top priorities of mining countries and communities. This is also the case for Antofagasta Minerals. Several years ago its mining group implemented an energy policy based on intelligent, strategic and sustainable management, in order to successfully face the challenges imposed by the market. It is called an intelligent policy because it intends to provide energy through a diversified range of sources, which includes the development of in-house alternatives. It is also a policy focused on efficient energy consumption and one that is strategic. Because it is in line with the characteristics of the mining activity, it is developed for the long term. Finally, what makes the policy sustainable is that it gives priority to energy usage from renewable resources and as such, the required capacities have been developed to generate innovative solutions that respond to the restrictions that characterize the industry today."

Jan 1, 2014

By Y. Kocaefe, D. Bhattacharyay, D. Kocaefe

The carbon anodes used in the electrolytic production of aluminum are made of petroleum coke, recycled anodes and butts, and coal tar pitch. Due to technological advances in the aluminum production technology, aimed at increasing production and decreasing energy consumption and greenhouse gas emissions, better quality anodes are required. Presently, the anode quality is evaluated by visual inspection and the analysis of a small core taken from 1.5-2% of the anodes produced. The visual inspection is susceptible to human error and limited to surface imperfections. The analysis of cores takes time, and therefore, it is difficult to determine the existence of a problem and intervene at the right time. In addition, the core does not represent the whole anode due to the non-homogeneity of anodes. A validated online anode quality control system can highly improve the situation. In this article, an electrical resistivity measurement method developed for this purpose is presented.

Jan 1, 2014

By F. Karakas

Organo-bentonite production enjoys important applications including solvent based paints and, more importantly, the production of polymer/bentonite nanocomposites. Quarternary ammonium salts in this regard are still considered as the most versatile reagents in the process of hydrophobization. In this study, a purified form of Resadiye region bentonites, which is one of the most significant sodium bentonite deposits in the world, was used. The raw Na-Bentonite was typically characterized by chemical analysis, XRD and DTA analysis and more importantly for its cation exchange capacity (CEC). Other technological properties such as swelling index, pH, apparent viscosity, water absorption, oil absorption were also conducted on the raw bentonite. The mineralogical analysis of the raw bentonite reveals that it contains about 80 % montmorillonite together with other associated gangue minerals including feldspar, quartz, calcite, dolomite, coloured impurities and other clay minerals. The raw bentonite was subjected to two stage processing involving a series of hydrocylones. Different apex and vortex diameters and different pressures were employed in order to produce a bentonite concentrate with 95 meq/100g CEC from a CEC of 71 meq/100 g. This high quality concentrate was used in the production of organo-bentontonite. The modification was performed with two different quaternary amines, i.e. Trimethyl Phenyl Ammonium Chloride (TPAC) and Hexadecyl Trimethyl Ammonium Bromide (HDTMA-Br). In the modification procedure, three parameters, i.e., adsorption density, zeta potential, swelling index and apparent viscosity were studied simultaneous-ly from the same suspension to identify both the mechanism of the process and also the degree of hydrophobicity. Adsorption measurements were made as a function of conditioning period, pH, and reagent concentration. Simultaneous examination of the adsorption density, zeta potential and apparent viscosity enabled us to pinpoint the optimum region of hydrophobicity which was subsequently tested by settling and critical coagulation concentration in both water as polar and toluene as nonpolar solvents. The results are analyzed in the light of experimental data.

Jan 1, 2014

By M. L. Cao

In this study, a montmorillonite organo-intercalation compound (MOIC) was synthesized by using a Na-modified bentonite (NaB) as a matrix and hexadecyltrimethylammonium (HDTMA) bromide as an intercalating reagent under microwave irradiation. The synthesized products were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), organic carbon content measurement, and adsorption density determination. The results show that, at 10% suspension concentration and 10 minutes irradiation in a 130-W microwave oven, the basal spacing d(001) of the synthesized MOIC increases to 2.209 nm from the original 1.218 nm of NaB. The MOIC has much higher adsorptive densities to nitrobenzene and aniline from aqueous solution than the NaB. The adsorption isotherm of nitrobenzene on the MOIC is linear, and the adsorption is mainly the result of nitrobenzene?s preferred partition in MOIC over aqueous solution due to MOIC?s hydrophobicity. The adsorption isotherm of aniline on MOIC follows the Freundlich equation and the increased adsorption is not only the result of aniline?s preferred partition in MOIC over aqueous solution but also that of the MOIC?s surface adsorptions.

Jan 1, 2014

By Peter Zhang

Room and pillar mining under shallow depth is usually conducted with a high extraction ratio, which leaves small pillars with a low safety factor in some old workings in abandoned mines. Pillar sloughage, squeezing or even collapse may have occurred in those old workings with small pillars, either at the time of mining or later. The conditions of the pillars in abandoned mines can affect mining above them. Subsidence fractures and abutment pressure are indications of multi-seam interaction caused by squeezing or collapse of small pillars. To mine over areas with potentially unstable small pillars, the panel layout in the upper seam should be such that multi-seam interaction can be minimized and proper roof and rib support should be installed in the influence zones. This case study presents an example of multi-seam mining above small pillars under a shallow depth of cover. Though the interburden is relatively thick and competent, interaction is still present over the influence zones. Pillar stability and multi-seam interaction analysis, numerical modeling and in-situ monitoring are presented to demonstrate how the upper seam can be mined safely over the small pillars.

Jan 1, 2014