Search Documents

By B Belle

In a deep, gassy predrained coalmine, ventilation and goaf drainage systems act as critical controls to manage longwall (LW) panel return gas levels. The goaf capture efficiency of most LW panels ranges from 45 to 85 per cent based on the gas domain at respective workings. Recent operational experiences have indicated that 50 m goaf hole spacing is optimal for management of high production retreat gassy LW panels, where the probability of goaf hole failures are frequent. Due to the horizontal stress direction geotechnical issues, goaf hole failure just behind the LW face is a recurring challenge resulting in significant and immediate increases in LW panel return gas levels. This paper presents a successful implementation of an innovative LW tailgate (TG) road cut through seal goaf fan/venturi system. The system incorporated a 17' (400 mm cased) hole drilled to 320 m deep in a perimeter roadway on a retreating LW TG road drawing the working seam horizon goaf gas behind the perimeter of seals. The surface goaf fan/venturi system was aimed to safely exhaust the LW deep goaf gas and thus withhold the goaf stream spillage to TG drive area and reduce the panel gas load by controlled operation of the system using continuous monitoring of CH4, CO and O2 levels. This control philosophy was made operational without impacting the use of the perimeter inbye ventilation shaft used for mine cooling and providing additional ventilation dilution capacity. The instantaneous reduction in TG gas levels of up to 0.3 per cent was observed even when the LW was 300 m away from the c/t seal goaf hole. Success of this concept TG seal goaf gas control system used even when the LW was 1300 m outbye has become an inventory of additional control for future deep and long LW blocks. This paper attempts to share the design process in addressing other risks and desired outcomes in managing the LW gas levels.CITATION:Belle, B, 2015. Innovative tailgate mobile goaf gas management in two gate road longwall panels – concept to implementation, in Proceedings The Australian Mine Ventilation Conference, pp 31–40 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By C Bie, S Li, P Xiao, P Zhao, H Lin

"Based on solid simulation material research, the simulation conditions for methane and coal solid-gas coupling were obtained using solid-fluid coupling theory. Using sand as the aggregate and paraffin and oil as the cementing agents, a material suitable for solid-gas coupling simulation was developed. A permeability testing instrument was also developed, and the compressive strength, brittleness parameters and seepage velocity of material were tested with different aggregates. The results showed that as the paraffin content increased, the compressive strength of the material increased but the permeability decreased. The oil removed the drawback of intensely changing material compressive strength. By setting a different ratio of aggregate to cementing agent, it can simulate rocks with different strengths and permeability. Applying the material to a mining simulation experiment revealed a relationship between methane seepage velocity and overlying strata movement. By extracting pressure relief gas from Shanxi Tianchi coalmine drainage, the authors found that the mining fissure zone was a storage area of pressure relief gas, and a gas drainage system can be placed to achieve good results. CITATION: Li, S, Zhao, P, Lin, H, Bie, C, Pan, H and Xiao, P, 2015. Character of simulation material of coal – rock and gas solid-gas coupling and engineering application, in Proceedings The Australian Mine Ventilation Conference, pp 105–110 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 31, 2015

By J Sargeant, T Levi, J Theiler, B Beamish

Two coal samples (810 Panel and Area 900) collected from Clarence Colliery have been tested under a controlled heating procedure to evaluate the gas evolution trends corresponding to increasing temperature. Gas evolution data are normally used to identify key gas indicators and validate the trigger action response plan settings for the mine as part of the Principal Hazard Management Plan for Spontaneous Combustion. The samples were located some 6 km apart and there is a significant coal-type difference between them. At low temperatures (<100°C), the Graham’s ratio (GR) values for the two samples are almost identical. However, at elevated temperatures, there is a significant difference, with the 810 Panel coal having higher GR values than the Area 900 coal. This is most likely due to a difference in the coal reactivity. The 810 Panel coal does not evolve ethylene until temperatures in excess of 140°C are reached, whereas Area 900 coal evolves ethylene once temperatures in excess of 120°C are reached. The 810 Panel coal also produces significant ethane evolution (200 ppm) at low temperatures (50°C) due to the presence of retained ethane seam gas, which decreases as the temperature increases due to desorption from the coal. Once the coal temperature exceeds 130°C, the ethane evolution increases again due to coal oxidation reactions, reaching levels of 50 ppm. In contrast, the Area 900 coal has no significant low-temperature ethane evolution, and ethane evolution only increases once the coal temperature exceeds 120°C. There are also noticeable differences in the trends of other gases evolved from the coal. These findings have implications for the interpretation of gas monitoring results from the two different areas of the mine. They also illustrate the need for obtaining results from each new area of a mine as it develops so that changing gas evolution trends can be identified in advance of mining.CITATION:Beamish, B, Sargeant, J, Levi, T and Theiler, J, 2015. Gas evolution trends for coal from two different areas at Clarence Colliery, in Proceedings The Australian Mine Ventilation Conference, pp 273–278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By D J. Brake

Most mine ventilation engineers are involved in ventilation planning and design in some capacity. Ventilation modelling software used by a competent experienced ventilation engineer is extremely useful in developing good ventilation designs by allowing assessment of a wide range of potential options. Unfortunately, ventilation modelling undertaken by persons who do not have sufficient experience or knowledge usually results in a façade that covers up a fundamentally unsatisfactory design. Ventilation models are produced for a wide variety of purposes including: fault-finding of a problem area in a mine and options analysis for resolution of such problems; a complete review or optimisation exercise of an entire mine’s ventilation system; or a much longer life-of-mine type of study. Models can be intended as the basis for studies with diverse purposes such as primary shaft or airway sizing, primary fan specification, examining re-entry times after blasting, resolving leakage or recirculation, or investigating the impact of fires or underground climate or cooling requirements. The concepts of ‘materiality’ and ‘fitness for purpose’ are essential to developing or using a ventilation model and serious mistakes have been made in wrongly using a ventilation model for purposes for which it was never intended, often because it is simply the most recent model on the mine site. Mistakes at this level often translate into faulty ventilation strategies and inefficient or ineffective use of scarce capital for ventilation projects. Validating a ventilation model is a time-consuming and expensive process and not every model must (or even should) be fully validated to meet the objectives at that time. This paper discusses the application of quality assurance in ventilation planning with particular respect to the ‘basis of design’ (BOD) as well as the standards for validating a ventilation model. It also provides a recommended way of dealing with non-conformances in measured versus modelled values of critical parameters in the model.CITATION:Brake, D J, 2015. Quality assurance standards for mine ventilation models and ventilation planning, in Proceedings The Australian Mine Ventilation Conference, pp 221–228 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By M Brady, O Salisbury, C Claassen, B Beamish, H Baxter

Monitoring for signs of elevated spontaneous combustion in the active goaf behind the longwall face is crucial for early intervention of any potential heating incidents. Typically, trigger action response plans (TARPs) are established at the start of longwall mining and often are only reviewed when triggers are activated frequently and become ‘nuisance alarms’, or in the worst case scenario after a heating event. Narrabri Mine has adopted a proactive approach of reviewing the longwall active goaf spontaneous combustion monitoring TARP at the commencement of each longwall block and prior to reaching a known ‘mylonite zone’ of crushed coal, which is associated with increased coal oxidation. The review is based on information recorded from the monitoring data of the previous longwall blocks as well as interpretation of relevant spontaneous combustion propensity results for the coal. This has resulted in the mine implementing a zoned TARP approach for each longwall block covering both the longwall retreat through normal undisturbed coal and the zone where the goaf is influenced by the increased coal oxidation associated with the mylonite coal. The consequence of this approach is that it has removed the issue of having nuisance triggers being activated during mining through a known increased oxidation zone, while maintaining a high awareness of indicators of spontaneous combustion.CITATION:Baxter, H, Claassen, C, Salisbury, O, Brady, M and Beamish, B, 2015. Implementation of a zoned trigger action response plan associated with changing mine conditions at Narrabri Mine, in Proceedings The Australian Mine Ventilation Conference, pp 113–120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By D Piason

Newstan Mine commenced mining operations in 1887 and has since undertaken extensive mining within the Young Wallsend, Great Northern, Fassifern, Borehole and West Borehole coal seams using a range of mining methods including board and pillar mining and longwall mining.Newstan Mine is planning to extend the existing mine workings using longwall and miniwall mining methods to produce up to 4.5 Mt/a of run-of-mine (ROM) coal for at least 25 years. The planned extension in the Main East and South West sections will involve developing new longwall panels and related mains headings. The new area contains higher specific gas emissions (SGE) than previously experienced at Newstan Mine. To achieve the optimum ventilation requirements for the longwall operation in this new area, a new ventilation shaft was designed to be constructed using the blind boring method in the South West Headings section.This paper presents the shaft design parameters and selection criteria for the construction of the new ventilation shaft, including the construction phase and the holing process to connect the shaft to the underground workings. The paper also discusses future ventilation requirements for Newstan Mine.CITATION:Piason, D, 2015. South-west ventilation shaft project at Newstan Mine, in Proceedings The Australian Mine Ventilation Conference, pp 229–238 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By V S. Mutton, M J. Shearer

"The current economic challenges faced by the mining industry led to a review of options for reducing the cost of ventilation control devices (VCDs). The VCDs at the Mount Isa Mines site operated by Glencore in Queensland typically experienced significant damage on the operating levels and required expensive replacements. Ventilation controls can become damaged by the effects of stope firings. This paper discusses the nature of blast wave effects, giving consideration to distance from the firing and changes in mine geometry. The time taken to adjust the airflow on the operating levels with the current VCDs resulted in the loss of productivity opportunities. The mine site engaged an equipment supplier to collaborate on the development of a high-strength regulator to control the required airflows within its underground workings.The strengthened regulator proved to be cost-effective and provided additional benefits, including ease of use, simplicity of installation and speed of change in the control of available ventilating airflow. An added advantage of the re-engineered regulator compared to contemporary VCDs is its flexibility, which includes the ability to easily move mobile equipment into different ventilation districts where required without the need to remove the VCD from its location. This paper describes both the innovation and environmental sustainability approaches followed when developing the new regulator for its implementation at the site.CITATION:Shearer, M J and Mutton, V S, 2015. Advanced ventilation control – an analysis of innovation and environmental sustainability, in Proceedings The Australian Mine Ventilation Conference, pp 55–62 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 31, 2015

By H Wang, D Wang

Mine dust is the most serious occupation hazard in coalmines. And many coal workers suffer from pneumoconiosis because of long-term inhalation of respirable dust. Reducing the dust concentration of workplaces by effective technical means is an important way to prevent coal worker’s pneumoconiosis (CWP). In order to overcome deficiencies in existing dust control technology for underground mining, especially the disadvantage of water spray technology mounted on roadheaders or continuous miners, the authors developed an integrated dust suppression technology utilising foam for fully mechanised heading faces. This paper presents an overview of the principles, materials, equipment and application of this technology. Among these, a jet type foaming device and a green foaming agent were developed, which can realise the goal of efficient preparation of foam. In addition, an arc fan nozzle used for foam spraying was invented, which can effectively cover and enwrap the dust produced by the roadheader at the cutting point and achieve the goal of efficient utilisation of foam. This dust suppression application of the proposed foam technology was investigated on fully mechanised heading faces. The results show that the dust concentration was cut down significantly with a dust suppression efficiency of greater than 85 per cent, an increase of over 30 percentage points compared to the water spray system. This study demonstrates that this foam technology can play an important role in dust suppression on fully mechanised heading faces, which provides an important method to improve the working environment and protect coal workers’ health.CITATION:Wang, D and Wang, H, 2015. Technology of dust suppression by foam for fully mechanised heading face, in Proceedings The Australian Mine Ventilation Conference, pp 177–182 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By E Corpuz, J Weissman, S Winter, R Evans

The surface-to-inseam (SIS) directional drilling technique has been utilised at Oaky Creek Coal for more than a decade to predrain both the Oaky No 1 and Oaky North mining areas. The cumulative drilling program constitutes a total of 140 lateral and 200 vertical holes, and 405 km of lateral drilling.The use of SIS gas drainage has been successful with the following site-specific benefits being recognised:ability to drain German Creek seam gas contents to residual gas levels of new mining areas within an 18-month period from commencement of well productionstructural geological verification of the mine design well in advance of development mining occurring in an areaability to conduct successful predrainage of the overlying Aquila seam to reduce subsequent goaf emissions.Appropriate and up-to-date geological knowledge during the design and drilling process is a significant influence to achieving success. Vertical production wells need to be located in a position that is most effective to remove water from hole. The lateral hole should not include intersections with significant geological structure.SIS drilling provides continuous seam roof/floor data to help define seam geometry and locate geological hazards with high accuracy. In faulted ground and with variable seam gradients, SIS data can resolve geological ambiguities from seismic sections and enhance seam correlation that would otherwise be available only from discrete and closely-spaced infill vertical exploration drilling.Here, we review some examples of SIS configurations and practice to highlight key learnings in drilling long inseam holes (up to 1900 m per arm) ahead of development and mining. Aspects on prerequisites, evolution of network design, tolerances and drainage outcomes in a variety of geological situations are discussed as technical basis towards a viable and effective SIS drilling program.CITATION:Corpuz, E, Evans, R, Weissman, J and Winter, S, 2015. Surface-to-inseam (SIS) drilling at Oaky Creek coal mine – SIS design aspects and drilling environment, in Proceedings The Australian Mine Ventilation Conference, pp 93–104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By J J. L du Plessis, S Viviers, G Ratner

Escalating electricity costs are one of the biggest operational cost drivers in mining. The trend to use high-powered auxiliary fans delivering increased airflow to meet the dilution requirements of diesel equipment, together with the reliance on ducted systems rather than traditional flow-through systems to ventilate areas, increases the overall energy requirements of ventilation systems. To manage and reduce electricity costs energy management systems can be implemented, inefficient operating units can be replaced and the operation of energy-consuming components of ventilation systems can be optimised.This paper describes the process followed to design and develop an energy-efficient axial flow auxiliary fan. The fan-targeted design was based on static pressure and volume flow rate requirements incorporating higher overall fan efficiencies. A brief overview of the results is given, including the aerodynamic design procedure using computational fluid dynamic (CFD) analysis. The mechanical design criteria used, including stress analysis on the rotor and designs to improve the vibration levels of the fan, are also presented. Through this study it was demonstrated that the aerodynamically designed rotors using profiled and twisted blades improve the total fan efficiency considerably when compared with some of the older-generation fans using cambered plates. The latter were typical in the mining sector in South Africa at the time of the study where average overall fan efficiencies of standard cambered fans less than 63 per cent and some of the older-generation cast aluminium blades have peak overall fan efficiencies of about 65 per cent. Peak overall fan efficiency of more than 80 per cent was achieved by using the described design and development process. Additional benefits are that the fans are quieter due to the better aerodynamic design and have a longer operating life due to reduced vibration levels.In conclusion, the use of CFD to develop fans to deliver the required volume flow at the required pressure allows quicker design turnaround time. It furthermore allows the ventilation engineer the option to specify a specific fan and is not limited to an off-the-shelf catalogue fan. It thus allows engineers to purchase a fit-for-purpose energy-efficient fan. The introduction of reliable fan control systems may, however, still result in the biggest cost benefit for underground mines.CITATION:du Plessis, J J L, Ratner, G and Viviers, S, 2015. Design and development of energy-efficient secondary axial flow fans, in Proceedings The Australian Mine Ventilation Conference, pp 337–344 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By F Wu, H Wang, W Chen

A pressurisation method with multiparallel fans has been adopted at HongLiuLin Coalmine to control the significant external air leakage through the goaf area of coalface 15207. Potential damaging effects of large external air leakage on a coalmine’s ventilation system are analysed according to the current air leakage status caused by the exploitation of shallow-covered coal seams. The use of pressure balanced ventilation to prevent external air leakage through goaf areas is introduced. The calculation of ventilation network of HongLiuLin Coalmine shows that the air resistance of an external air leakage branch through a goaf area and the air pressure drops from the intake slope to the working face can be adopted to determine the values of pressure to be increased by regulating fans and airflow controlling parameters of regulators. By investigating airflow requirements of the pressure-balanced area as well as the performances of the auxiliary fans currently used in the coalmine, the number of pressurisation fans needed is fixed. The expected result is achieved after the pressurisation method has been carried out, which can be helpful for other coalmines to handle similar problems.CITATION:Wu, F, Chen, W and Wang, H, 2015. Multiparallel fan method to prevent significant external air leakages through a goaf area of a shallow covered coalmine, in Proceedings The Australian Mine Ventilation Conference, pp 267–270 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By T J. Laing, A B. Richards, A J. Moore

Blastholes fired in a pattern with a constant initiation delay create a frequency in the ground vibration similar to that from a percussion instrument, such as a drum, in the air. A constant firing delay generates a prime or forcing frequency into the ground motion. The forcing frequency may then be modified by ground transmission characteristics into subharmonics of the forcing frequency. The moving vibration source between blastholes also creates a frequency shift because of a Doppler effect. Other wave interactions may form beats. The effects are exacerbated by the accurate firing times of electronic detonators. This paper demonstrates how observations of wavetraces and frequency spectral analysis were used to recognise:Doppler effect and frequency ellipsoidssubharmonics (and sub-subharmonics) of the forcing frequencybeat formation that may double or triple peak particle velocity (PPV) levels.Recognition of beats permitted techniques to be used to control ground vibration from coal overburden blasting to limits deemed to cause no further instability in a slip failure. An understanding of the science involved has practical application elsewhere that has been successfully applied to initiation timings to reduce PPV and adverse human and structure response from other blasting operations.CITATION:Moore, A J, Richards, A B and Laing, T J, 2015. Blasting harmonics and controlling peak particle velocity, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 527–532 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Y M. Wang, W Z. Liu, L F. Li, X L. Zhang

Based on the blasting crater theory, the equation between k under typical cases and burden line, charge height was obtained by open pit bench blasting analysis model. The model was calculated with mine production blasting. The blastability coefficient k and the best range of blasting burden line were specially emphasised on determination of lateral crater tests.CITATION:Wang, Y M, Liu, W Z, Zhang, X L and Li, L F, 2015. Application of lateral crater test in open pit blasting parameters optimisation, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 463–468 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By H S. Mitri, A Sainoki

Destress blasting techniques have been widely employed in underground mines for the purpose of preconditioning highly stressed rock mass. Appropriate applications of the technique successfully contribute to increasing mine safety (eg mitigating the risks for rock bursts). This paper presents a simulation technique to estimate the extent of damage zones induced by destress blasting. A 3D numerical model with a single blasthole is constructed with FLAC3D code, whereby static analysis is carried out in which horizontal and vertical stresses are applied to the model in order to simulate stress conditions in a deep underground mine. Afterwards, dynamic analysis is performed whilst applying time-varying blast pressure along the blasthole. The blast pressure profile takes into consideration an instantaneous increase and gradual decrease in blast pressure as well as the propagation of detonation along the blasthole. In this paper, constitutive models allowing for shear and tensile strengths of rock mass that are dependent upon strain rate are newly implemented into FLAC3D code with C++ programming language, whereby blast-induced damage is assessed by the extent of tensile and shear failure zones. The results obtained from the dynamic analysis show significant decrease in the extent of yielding zones induced by destress blasting with increasing the magnitude of in situ stress. They indicate that considering in situ stress state is indispensable in order to propose proper blast design for each level in underground mines. Based on these results, the relationship between the extent of the damage zone and depth at which destress blasting is performed is established. Furthermore, stress dissipation induced by destress blasting is examined with static analyses, in which the modulus of elasticity is decreased according to a rock fragmentation factor, a, only for the area where tensile and shear failures takes place during the dynamic analyses. A model parametrical study with respect to a is undertaken. The relationship between the rock fragmentation factor and the stress dissipation in the yielding zones is developed from the parametrical study. The developed relationship can be useful when destress blasting is designed for massive rock masses.CITATION:Sainoki, A and Mitri, H S, 2015. Simulation of damage zones induced by destress blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 245–256 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By D Deb, R Pramanik

This paper presents a generalised methodology in smoothed particle hydrodynamics (SPH) framework to analyse dynamic failure process of rock mass having natural joint under blast-induced stress wave and expansion, and penetration of high pressure gaseous product. The necessary interactions of gas-rock are incorporated in the model which describes features of coupling between damage and plasticity in tension and compression respectively. A Drucker-Prager formulation of plasticity is used to model the behaviour of aggregate field and the Grady-Kipp damage model is employed for tensile strain. These two material behaviours are then brought together within the framework of interacting continua. The model relies on the Drucker-Prager plasticity surface to predict the dilatancy aspect of the material response and to account change of strength according to the strain rate effect. Three numerical examples are presented with rock joint and multiple blastholes.CITATION:Deb, D and Pramanik, R, 2015. Smoothed particle hydrodynamics modelling of blast-induced fracture processes in naturally jointed rock medium, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 65–70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By D Johansson, C Yi, U Nyberg

Emulsion explosives are a common industrial explosive and have a non-ideal detonation behaviour. The detonation performance for a given product changes with the charge diameter, ground conditions, con?nement and density. The burning process of an emulsion explosive has been modelled with an ignition and growth model in the LS-DYNA code. The parameters in the burning rate function are calibrated by the detonation velocities and the detonation front curvature radii from emulsion explosive tests. A Perl program was developed for an efficient estimation of the parameters, and the results show that the calibrated parameters can predict both detonation velocities and the detonation front curvatures.CITATION:Yi, C, Nyberg, U and Johansson, D, 2015. Parameter determination of an ignition and growth model from emulsion explosive tests, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 585–590 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

This paper will review some of the work conducted in the past at the Dynamic Effects Laboratory to examine the use of stress waves and fracture mechanics in understanding dynamic fracture and fragmentation in blasting applications. Along the way, we will use photoelasticity and high-speed photography to better understand the mechanisms of fracture and fragmentation.CITATION:Fourney, W L, 2015. The role of stress waves and fracture mechanics in fragmentation, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 27–40 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By G Gopinath, R Balachander, H S. Venkatesh

This paper describes in detail the controlled blasting adopted and the measurements undertaken for the successful excavation of large twin tunnels under a shallow cover for a six-lane highway project in India. The tunnels are D-shaped, each 15 m in diameter, and the cover between the tunnels and the existing railway track was about 14 m. These twin tunnel tubes were characterised by two separate three-lane carriageways for each direction of traffic, and were planned with about 25 m of reinforced cement concrete (RCC) portals at the entrance and exit of the tunnels. The major challenge of the project was the blasting of tunnels in rock below an operating railway line. As the tunnels approached the area below the railway line, the ground vibrations were monitored vertically above the blasting faces and on the railway track sleepers. Vibration intensities between those generated from tunnel blasting and those from the movement of the trains were compared, and it was found that the vibrations from blasting were lower than those from the moving trains. Though the permissible level of ground vibration based on the Indian Standard (IS) code happens to be 70 mm/s, the maximum charge per delay was calculated restricting this limit to 50 mm/s. This ensured that the vibrations in the vicinity of the railway tracks never exceeded the prescribed limit of 70 mm/s. The surface ground settlement before and after the blasts were also measured using an optical levelling instrument, which confirmed that there was no significant impact on the surface movements due to blasting. Extensometer readings inside the tunnels showed that there was no deformation in the tunnel. These twin tunnels are now operational and are providing faster connectivity with safety.CITATION:Gopinath, G, Venkatesh, H S and Balachander, R, 2015. Controlled blasting for twin tunnels with a shallow cover under an operating railway line, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 801–808 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By C Parihar, R Garg, A Bhandari, S Bhandari

Blasting can impact the efficiency of entire downstream mining operation. Individual technology solutions for blasting have been available in the industry for many years but all of them only cater for certain aspects of blasting. Many of them are based on individual research and/or experiences. Some of the available software solutions are not suitable to be used in the field as that they need advanced skills or tools. Also, most do not take technology advancements like mobility, advanced data analytics, web solutions and integration into consideration. Hence, no technology platform is currently present in the industry that addresses all potential needs a blaster may need in an integrated manner.This paper presents an integrated solution that takes care of all aspects of blasting – design blasts according to mine plan; collect data after drilling has been carried out (as there is often difference in designed and actual drilled hole locations in the field); predict blast results in terms of fragmentation, flyrock, ground and air vibrations, wave front reinforcement and flyrock distance; and after assessment, allows changes in charging, delay timing and sequence. The technology solution is a secure, cloud-hosted, web-based software-as-a-service solution that can be accessed from anywhere. Also it has a mobile app, which is available for both Android and iPhone/iPad. The mobile app is also integrated with the web-based solution using application programming interface calls to the central data repository.Case studies for two limestone mines are presented where this solution is being used in its initial format. This software platform enabled analysis of the outcome from a previous blast pattern and then subsequently allowed optimisation of blasting operations based on historical data. Uses of this platform have resulted in improved key performance indicators in these two limestone mines. The mobile app as part of this platform enables extensive field blast data capture and analysis and also various predictions before a blast. Data collected include blast parameters, individual hole charging, initiation pattern, videos, photographs and vibration records for analysis/reporting. The key features of the solution are a blast designer, a detailed blast data collection/analysis and a series of environmental predictors. These predictors give blast results in terms of fragmentation, flyrock, ground and air vibrations and wave front reinforcement and take remedial steps before blasting to optimise and control adverse environmental impact. Many features, such as fragmentation predictor and mobility solution, are completely unique features that are not available elsewhere in such a field personnel-friendly manner.CITATION:Bhandari, S, Parihar, C, Garg, R and Bhandari, A, 2015. An integrated technology solution for optimised and environmentally-controlled blasts, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 393–400 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Q Yu, G Ren, Z-Y Chen, J Yang

The wedge shape theory of the rock fragmentation range in bench blasting is presented according to the dynamic characteristics of rock fragmentation by blasting in open pit under the condition of hole-by-hole initiation. The finite element software ABAQUS was used to analyse the rock fragmentation mechanism. The rock mass stress contours, crack propagation and damage evolution of different moments were obtained. The results showed that the wedge shape theory of blasting is closer to the rock fragmentation in hole-by-hole blasting and is useful to the design and calculation of charge weight.CITATION:Yang, J, Chen, Z-Y, Yu, Q and Ren, G, 2015. The wedge theory of borehole charge design for bench blasting and its numerical simulation, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 169–176 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015