Search Documents

By Merlyn B. Buhle

The value of the earth resistivity method in groundwater studies in Illinois has long been recognized. Owing to the sharp electrical contrasts between sand and gravel deposits and glacial till, alluvial silt or underlying shale, much of the earth resistivity prospecting has been of a relatively elementary nature and has been highly successful. Approximately 90 pct of earth resistivity interpretations by the State Geological Survey have been accurate for practical purposes. Four studies involving fairly simple geologic situations are presented in this paper as typical cases. FOR the past 20 years electrical earth resistivity exploration has been used in Illinois in many phases of study undertaken by the State Geological Survey, chiefly in locating and outlining deposits of water-bearing sand and gravel from which to obtain ground water for municipal and industrial supplies. At least 43 municipalities in the state derive their total water supply from deposits of sand and gravel discovered by resistivity methods. These deposits occur in both Quaternary and preglacial valleys and within much of the glacial drift which covers a large portion of the state. In recent years there has been much demand from rapidly growing municipalities for help from the Illinois Geological Survey to extend existing well fields. Water supplies for many and varied industries constitute a considerable portion of the Survey's studies. The diminishing need of water supplies for railroads has 'been accompanied by an increasing demand by the oil industry for water for secondary recovery programs. The instruments used by the Illinois Geological Survey follow closely the commutated direct current circuits developed by O. H. Gish and W. J. Rooney' using the Wenner2 electrode configuration. More recently replacement of the hand-driven commutator by a synchronous vibrator has led to increased ease of operation and accuracy. Continuing improvement of equipment and technique has led to many changes in the instruments, but the operating theory remains the same. In the field operation at a selected station, four electrodes are set at equal distances in the ground 6 to 10 in. deep, in a straight line. A 16 to 20-cycle current is applied to the two outside steel electrodes

Jan 1, 1954

By Harold M. Mooney

WHEN apparent resistivity data are taken with the symmetrical Wenner 4-electrode spread, a fixed center position is used and readings are taken for values of electrode separation. Basic data consist of apparent resistivity plotted against separation of adjacent electrodes . The interpreter attempts to infer geologic structure, such as the depth to discontinuities and the nature of subsurface earth materials. An earlier paper' described methods for interpreting resistivity data. All of these involve a severe assumption, namely that the earth in the region of interest consists of horizontal layers, electrically homogeneous and isotropic. The actual earth never satisfies this assumption exactly and may deviate from it so much that none of the above methods can be applied. Attempts in three directions have been made to modify the assumption so that it approaches known geologic complexity more closely. First, curves have been calculated for dipping discontinuities. Stern' and Aldredge hose a few widely separated dip angles. Trudu confined his attention to small dips. Berel'kovskiy and Zubanov computed gradient curves for widely separated dip angles. Unz as given the most complete solution, with a brief attempt to treat the three-layer case. Second, anisotropy can be taken into account. It seems geologically probable that layered materials have different vertical and horizontal conductivities. Cagniard, Maillet, and Pirson et up methods for finding an equivalent hypothetical isotropic medium. Standard interpretation methods can be applied to this, and the actual medium can then be deduced. Belluigi'" discounts the practical importance of anisotropy; Geneslay and Rouget do not agree with his conclusion. Third, the effect of variable resistivity in a layer can be considered. Keck and Colby" examine the mathematics of an exponential increase in a surface layer. Several authors, for example, Stevenson,'' consider a continuous variation of resistivity with depth. The present paper deals with a linear variation of resistivity in a surface layer. Geologically, surface variations should be expected. Unconsolidated materials such as glacial drift show marked irregularities over short distances. The effects of weathering change with depth. The moisture content of material above the water table may vary from a dry sand to a saturated clay, and both of these will be changed by rainfall. Figs. 1 to 6 present apparent resistivity curves to show the effect of a variable surface layer. In all cases resistivity varies linearly with depth down to a depth of one unit. Material beneath this depth has constant resistivity. Electrode separation is plotted in depth units. Insets on each figure show the corresponding cross-sections, plotting true resistivity against depth. To illustrate, consider curve A of Fig. 1. The true resistivity of material at the surface of the earth is taken as 0.4 units. Resistivity increases with depth, reaching a value of 1.0 at 0.5 depth units and 1.6 at 1.0 depth units. Below a depth of 1.0, all the material has very low resistivity (zero, for purposes of calculation). Curve A in the main part of Fig. 1 shows how apparent resistivity varies for this case as the electrode spacing is increased. To illustrate further, curve E of Fig. 4 corresponds to true resistivity of 1.2 units at the surface, 1.0 at a depth of 0.5 units, 0.8 at a depth of 1.0, and 1.5 for all depths greater than 1.0. Apparent resistivity curves have been plotted logarithmically so that the shape of the curves becomes independent of the units, giving the curves wide validity. A certain drift-covered area, for example, shows a gradual decrease of resistivity from 230 ohm-meters at the surface to 150 ohm-meters at the bedrock surface, 275 ft down; bedrock resistivity is 800 ohm-meters. Curve E of Fig. 5 indicates that true resistivity decreases from 1.2 units at the surface to 0.8 at a depth of 1.0, then increases abruptly to a constant value of 4.0 units. Since resistivity and depth ratios are the same, this can be used to predict the field curve. For Fig. 5, multiply true resistivity and apparent resistivity by

Jan 1, 1955

By Robert G. Van Nostrand, John H. Henkel

TRANSIENT potentials obtained in resistivity prospecting can be separated into two classes. The first is electromagnetic, has a comparatively short time constant, and increases in relative amplitude as the electrode separation is increased. These electromagnetic transient potentials, of which an excellent theoretical treatment is given by Yost: are the result of changes in the current and can be classed as differentiated signals. The second class is electrochemical, has a comparatively long time constant, and decreases in relative amplitude as the electrode separation is increased. The electrochemical signals are generated by the current flow itself and can be classed as integrated signals. The transient potentials due to electrochemical factors are the subject of this article. The phenomenon is referred to as induced polarization. Schlumberger" was the first worker to observe induced polarization, but he was unsuccessful in attempts to apply the principles of induced polarization in electrochemical prospecting. Other workers, notably Bleil; have studied polarization and in some cases pointed out its possibilities, but no theory has been presented that describes polarization and its time dependence adequately. It is the purpose of this discussion to present the essence of a theory to geo-physicists and to show that it leads to results consistent with experimental evidence. The theory on which this analysis is based has existed in electrochemical circles since 1910."

Jan 1, 1958

By F. C. Canney

Geochemical prospecting seeks hidden mineral deposits by sampling for variations in the chemical composition of naturally occurring materials. Usually the samples are of soils and other products of weathering and erosion—surface materials extremely susceptible to contamination by human activities. Except when a survey is conducted well away from populated areas, contamination is an ever-present hazard. The program's success is particularly endangered when the contaminants are the elements sought; if these occur erratically throughout an area, spurious anomalies completely unrelated to mineralized areas can be formed. Evenly distributed contamination can be dangerous too, if it raises the background to such a level that true anomalies can no longer be easily detected. Suppose, for example, that in an area where the lead background is 20 parts per million the soil over a lead vein contains 1000 ppm of lead. Here the contrast would be 50 to 1, which is very satisfactory for geochemical surveying. Now if 1000 ppm of lead from some source were added evenly to the soil in this area, the contrast would be reduced to about 2 to 1, and the anomaly would no longer be readily detectable because a threshold of significance twice the value of the background is the minimum generally used for interpreting geochemical data. Of the many possible sources of contamination, probably most important are smelter fumes, which may distribute large quantities of metal contaminants over many square miles of ground. For several reasons, the investigation reported here was begun in the Coeur d'Alene district in northern Idaho: 1) a lead smelter has been operated in this district since 1917 and an electrolytic zinc plant since 1928, and presumably the contamination patterns are strongly developed; 2) to evaluate the usefulness of certain geochemical techniques, V. C. Kennedy and S. W. Hobbs of the USGS had already studied the distribution of copper, lead, and zinc in the soils (both in background areas and other veins) and in the water and plants, providing a criterion for measuring the magnitude and effect of soil contamination; 3) one of the economically important parts of the district lies south of the South Fork of Coeur d'Alene River and within a radius of five miles of the reduction plants near Smelterville (Fig. 1). In this area, and in the entire district, conventional methods of prospecting are hindered by heavy vegetation and thick soil cover, and the possibility of contamination by smelter fumes has discouraged geochemical prospecting. Should data reveal that geochemical prospecting could be done successfully in such an area, a particularly useful tool would be available to mining companies and prospectors searching for concealed orebodies in this economically important part of the district. The field work on which this report is based was done from July 28 to 31, 1955. It should be emphasized that this was reconnaissance study only, and therefore far from exhaustive. Previous Investigations in U. S. : The first geochemical survey known to have been affected by contamination was conducted in 1940—a geobotan-ical reconnaissance made in the Michigan copper district by a private company. Geologists found striking variations in the copper content of oak and maple leaves, but unfortunately the high copper isograds of the study seemed to be related more to the Calumet and Hecla copper smelter fall-out than to mineralized ground.' The leaves of one oak tree near the smelter contained 0.4 pct Cu. Similar contamination was reported by Clarke (Ref. 2, p. 41), who conducted experimental geochemical soil and botanical surveys at Ray, Ariz. He found that the leaves of oak trees growing in unmineralized ground near Superior, Ariz., contained more copper than the leaves of oak trees growing on the capping of the Ray orebody and attributed this fact to contamination from the fumes of the Magma smelter at Superior. According to H. E. Hawkes,3 soils and stream sediments in the Superior area are also severely contaminated. Hawkes' work there has shown a copper content averaging 0.5 pct in the surface horizons of soils within one mile of the smelter stack. Samples taken only a few inches below the anomalous surface samples showed only background copper values. In 1950 L. C. Huff' of the USGS made a geochemical survey in an area near Jerome, Ariz., and found considerable zinc and copper in the soils over unmineralized basalt close to Clarkedale, Ariz., and over limestone close to Jerome. As the amounts were notably greater than could reasonably be expected to be derived from the underlying rocks, Huff suspected airborne contamination from the smelter at Clarkedale. Description of Area: The area sampled in detail (Fig. 1) for the study presented here is one of strong relief. The dominant watercourse is the westward-flowing South Fork of the Coeur d'Alene River. East of Kellogg the South Fork flows in a rather narrow canyon, but its valley floor widens considerably to the west where much of the flood plain is covered by an extensive veneer of mining, milling, and smelting debris. South of the South Fork and between Big Creek and Pine Creek is a mountainous area where

Jan 1, 1960

By C. A. Heiland

THIS year's review of geophysical activities has a somewhat different complexion than usual. With the ending of the war, the time seems opportune to supplement the customary report on operations and discoveries in oil and mine exploration by a review out-lining the contributions of geophysicists to the. war effort. To give as much space as possible to the latter, presented as Part 2, some of the usual review features have been omitted from the statistical section, given as Part 1 immediately following.

Jan 1, 1946

By Rollyn P. Jacobson

THE town of Pacific, in Jefferson County, Mo., is 127 miles west of St. Louis. Since the area lies entirely on the flood plain of a cutoff meander of the Meramac River, it was considered a likely environment for accumulation of commercial quantities of sand and gravel. Excellent transportation facilities are afforded by two major railways to St. Louis, and ample water supply for washing and separation is assured by the proximity of the river. As a large washing and separation plant was planned, the property was evaluated in detail to justify the high initial expenditure. An intensive testing program using both geophysical and drilling methods was designed and carried out. The prospect was surveyed topographically and a 200-ft grid staked on which electrical resistivity depth profiles were observed at 130 points. The Wenner 4-electrode configuration and earth resistivity apparatus" were used. In all but a few cases, the electrode spacing, A, was increased in increments of 11/2 ft to a spread of 30 ft and in increments of 3 ft thereafter. Initial drilling was done with a rig designated as the California Earth Boring Machine, which uses a bucket-shaped bit and produces a hole 3 ft in diam. Because of excessive water conditions and lack of consolidation in the gravel there was considerable loss of hole with this type of equipment. A standard churn drill was employed, therefore, to penetrate to bedrock. Eighteen bucket-drill holes and eight churn-drill holes were drilled at widely scattered locations on the grill. The depth to bedrock and the configuration will not be discussed, as this parameter is not the primary concern. Thickness of overburden overlying the gravel beds or lenses became the important economic criterion of the prospect.** The wide variety and gradational character of the geologic conditions prevailing in this area are illustrated by sample sections on Fig. 2. Depth profiles at stations E-3 and J-7 are very similar in shape and numerical range, but as shown by drilling, they are measures of very different geologic sequences. At 5-7 the gravel is overlain by 15 ft of overburden, but at E-3 bedrock is overlain by about 5 ft of soil and mantle. Stations L-8 and H-18 are representative of areas where gravel lies within 10 ft of surface. In most profiles of this type it was very difficult to locate the resistivity breaks denoting the overburden-gravel interface. In a number of cases, as shown by stations M-4 and H-18, the anomaly produced by the water table or the moisture line often obscured the anomaly due to gravel or was mistaken for it. In any case, the precise determination of depth to gravel was prevented by the gradual transition from sand to sandy gravel to gravel. In spite of these difficulties, errors involved in the interpretation were not greatly out of order. However, results indicated that the prospect was very nearly marginal from an economic point of view, and to justify expenditures for plant facilities a more precise evaluation was undertaken. The most favorable sections of the property were tested with hand augers. The original grid was followed. In all, 46 hand auger holes were drilled to gravel or refusal and the results made available to the writer for further analysis and interpretation. When data for this survey was studied, it immediately became apparent that a very definite correlation existed between the numerical value of the apparent resistivity at some constant depth and the thickness of the overburden. Such a correlation is seldom regarded in interpretation in more than a very qualitative way, except in the various theoretical methods developed by Hummel, Tagg (Ref. 1, pp. 136-139), Roman (Ref. 2, pp. 6-12), Rosenzweig (Ref. 3, pp. 408-417), and Wilcox (Ref. 4, pp. 36-46). Various statistical procedures were used to place this relationship on a quantitative basis. The large amount of drilling information available made such an approach feasible. The thickness of overburden was plotted against the apparent resistivity at a constant depth less than the depth of bedrock for the 65 stations where drilling information was available. A curve of best fit was drawn through these points and the equation of the curve determined. For this relationship the curve was found to be of the form p = b D where p is the apparent resistivity, D the thickness of overburden, and b a constant. The equation is of the power type and plots as a straight line on log-log paper. The statistical validity of this equation was analyzed by computation of a parameter called Pearson's correlation coefficient for several different depths of measurements, see Ref. 5, pp. 196-241. In all but those measurements taken at relatively shallow depths, the correlation as given by this general equation was found to have a high order of validity on the basis of statistical theory.

Jan 1, 1956

By H. W. Fleming, R. R. Brooks

The Clearwater Deposit, a small occurrence of massive-sulphide mineralization enclosed in an envelope of disseminated-sulphide mineralization, was discovered as a result of an aeroelectromagnetic survey in New Brunswick in 1955. Subsequently, additional flights were made over the deposit and various ground follow-up methods were employed to ascertain the nature of their response. All methods proved to be capable of indicating the occurrence with varying degrees of precision. This paper is a presentation and a discussion of the magnetic and electromagnetic data, both airborne and ground, and the self-potential data obtained over this deposit. The attention of Canadian mining exploration companies was initially focussed on New Brunswick by the discovery, in 1953, of the Brunswick ore body. Ground electromagnetic surveys were of considerable assistance in locating and developing this deposit. In the following year, 1954, the Heath Steele base-metal deposits were discovered by employing an airborne electromagnetic device and ground electromagnetic surveys to follow-up the airborne indications. These discoveries demonstrated clearly that both airborne and ground electromagnetic techniques were applicable for locating the near-surface deposits of massive sulphides present in this region. Airborne electromagnetic equipment became available on a contract basis through Aeromagnetic Surveys Limited early in 1955 and was used extensively thereafter throughout a large portion of northern New Brunswick. It was as a result of one of these surveys with Aeromagnetic Surveys Limited equipment in the summer of 1955 that the Clearwater Deposit was detected. The airborne anomaly was located on the ground by means of an electromagnetic survey using a Swedish Slingram unit. During 1956, the region was investigated more thoroughly- in the hope that other sulphide bodies might be located. Airborne electromagnetic coverage was extended and the Clearwater Deposit itself was used as a testing ground for the various methods and types of equipment currently in use in New Brunswick. In this paper com prative data are presented for the airborne magnetic, airborne electromagnetic, ground magnetic and ground electromagnetic surveys over this deposit. The ground electromagnetic instruments used were the McPhar vertical-loop unit and the Slingram and Boliden horizontal-loop units. Self-potential surveys were carried out with a McPhar unit. From the geophysical point of view, all ground electrical methods employed indicated the presence and the extent of the massive-sulphide mineralization with a good degree of accuracy. The horizontal-loop methods however, defined the contacts more precisely as is to be expected when dealing with a flatly-dipping

Jan 1, 1961

By Carl Tolman, LeRoy Scharon, Harold Powers

THIS paper presents geophysical and subsurface data observed in the vicinity of Shafts No. 1 and and 5 of the National Lead Co. lead mines at Fred-ericktown, Madison County, Missouri, see Fig. 1. The area selected is an excellent example to illustrate the close correlation between geophysical data and geological facts as revealed by drilling and mining. Such close correlations make geophysical applications appropriate to the development of known ore-bodies as well as the exploration for new orebodies. In the past, magnetic and shallow electrical resistivity observations were made over limited areas in the Fredericktown lead district by the Missouri Geological Survey, with favorable results. The first extensive magnetic and electrical resistivity surveys were started by the U. S. Bureau of Mines in May 1945 in two areas located northwest and southwest of Fredericktown, as shown in Fig. 1. The results of these surveys were reported in April 1948 at Denver, spontaneous-polarization surveys were made over the property of the St. Louis Smelting and Refining Co. at Fredericktown by Sherwin F. Kelly Geophysical Services, Inc. Aeromagnetic surveys were completed in 1948 over the Fredericktown quadrangle by the U. S. Geological Survey. Since 1945 geophysical surveys have been an important part of exploration programs in the Fred- ericktown district. Such methods, magnetic and electrical resistivity, are now serving as guides in the further development of known orebodies. On an irregular pre-Cambrian igneous erosion surface Lamotte sandstone of upper Cambrian age was deposited, partially filling the topographic basins, see Fig. 2. Above and conformable with the Lamotte sandstone lies the Bonneterre formation, a dolomite with locally interbedded thin dolomitic limestones and shales at its base. This formation also only partially filled the topographic basins. The Bonneterre was overlain by the Davis, Derby, Doe Run, and Potosi formations, which are principally dolomite. Uplift, tilt, and slight warping has allowed erosion and weathering to remove most of the sediments overlying the Bonneterre, and in many places, not far from the mine, the Lamotte sandstone is exposed. This erosion has also exposed areas of pre-Cambrian igneous rock. The Lamotte sandstone, having been deposited on an irregular pre-Cambrian surface, is extremely variable in thickness and ranges from zero where it laps the pre-Cambrian rocks to 250 ft thick in the deeper basins. In the vicinity of the mines the Bonneterre dolomite ranges from zero where it wedges out against the pre-Cambrian igneous rocks to 400 ft thick. The ore deposits occur as a bedded disseminated type1 and are chiefly composed of galena and pyrite with minor amounts of chalcopyrite and siegenite. Heavy pyrite and marcasite mineralization may be found throughout the Bonneterre formation. However, there is little or no apparent association of these iron sulphide bodies lying above the ore hori-

Jan 1, 1954

By G. E. Frantti

UNDER the auspices of the Geophysical Committee of Michigan College of Mining and Technology, an investigation was made in Michigan's Upper Peninsula to obtain geophysical data" related to the regional subsurface geology in the area covered by Paleozoic sediments. The area surveyed includes that portion of the Upper Peninsula which lies between R18W to R26W and T41N and T49N, covering approximately 1300 square miles. On the index map, Fig. 1, it is represented by the cross-hatched zone west of Munising. Four of the five sites of detailed investigation are indicated by the letters A, B, C, and D. A detailed gravity and magnetic survey had previously been conducted by J. G. Wilsonz near Perkins, 8 miles north of Rapid River, on a local anomalous area. Results of his work, which showed a large positive magnetic anomaly associated with a gravity anomaly, aroused interest in the possible economic significance of the formations underlying the Paleozoic sediments in this part of the Upper Peninsula. Early in the 1900's the Michigan Geological Survey, as well as many private companies, had done a considerable amount of dip needle work near the southwest corner of the area discussed in this paper. Most of the information available to the writer was obtained from indicated magnetic anomalies on the geological map of the northern peninsula of Michigan. Results of the geophysical activities of mining companies in the vicinity of the Marquette range and Gwinn district were unavailable to the author. Physiography and Geography: The region under consideration has low to moderate relief. About half the area is comprised of swampy lowlands, and because of the swamps and forests much of the land is almost inaccessible. The major drainage system is dendritic, with streams flowing into Lake Michigan on the south and Lake Superior on the north. The general geology, shown in Fig. 2, indicates an overlay of Paleozoic sediments on pre-Cambrian formations along a line running approximately south from Marquette (not shown on the geological map). Actual contact between pre-Cambrian and Paleozoic sediments is not known because most of the area is covered with glacial till, and outcrops are very scarce. Exposures of the Paleozoic sediments show that these beds in the northern areas dip gently under Lake Superior and that in the southern areas they 'dip gently to the southeast. Outcroppings of the pre-Cambrian formations occur primarily to the west of the surveyed area except in the northwest corner where the Laurentian series outcrop as far east as the Gwinn district and also in T46N, R24W. Instrumentation: Gravity measurements were made with the Worden portable gravity meter. Since this was chiefly a reconnaissance regional survey, both the large and small dials were used. The instrument used had a constant of 0.0035 milligals per scale division, a working range of about 25 milligals.

Jan 1, 1957

By H. LeRoy Scharon, A. B. Cleaves

THE application of geophysical techniques in the A engineering surveys of the Philadelphia and Western Extensions of the Pennsylvania Turnpike System is unique inasmuch as this is the first time, (to the authors' knowledge), that such studies have been employed on a large scale on a major highway system. These investigations were confined to specific areas along the center line of the proposed Philadelphia Extension between Carlisle and King of Prussia, and the Western Extension between Irwin and the State line near Youngstown, Ohio, as shown in Fig. 1. Along the 100 miles of the philadelphia Extension, the geophysical surveys were confined to 137 individual cuts and comprised a total length of 37.4 miles of line. The Western Extension, 66 miles in length, has 108 individual cuts. The accumulated length covered by electrical resistivity studies was 17.3 miles. The depth of the cuts varied from a minimum of 10 ft to a maximum of 62 ft. The geophysical investigations were made for the purpose of determining depths to bedrock in the 245 proposed cuts and at the sites of various structures. The 'data also served as a basis for geological interpretations of the condition of bedrock, contact zones, rock types, water table, and other factors significant in highway construction. The geophysical method of investigation employed the use of the electrical resistivity principle using the Gish-Rooney type electrical resistivity meter and the Wenner electrode configuration.* Apparent resistiv- ities were determined for constant intervals to various depths and were correlated with surface geological observations and subsurface geological conditions revealed by key diamond drill holes situated within a given cut interval. From these correlations, depths to bedrock were postulated with notations on other geological features that might be pertinent to modern highway construction. Geology The bedrock underlying the areas of the extensions of the Turnpike afford an excellent academic study of the electrical resistivity depth method as well as a practical application to modern highway engineering. The rocks encountered on the Philadelphia Extension vary in age from pre-Cambrian to Triassic and Quaternary, whereas in the Western Extension, bedrock is confined to relatively flat-lying strata in the Allegheny, Conemaugh, and Monongahela formations of the Upper Paleozoic, Pennsylvanian. Glacial and Recent stream, valley, and terrace deposits are common. Philadelphia Extension The oldest bedrock encountered in this extension are igneous and metamorphic. These, encountered chiefly in Chester County, consist of the strongly

Jan 1, 1952

By D. O. Wyble, L. O. Bacon

THERE has been considerable speculation among mining geologists and mining men in general as to the relative merits of gravity methods in iron-ore exploration. Most of the investigations which have been carried out in recent years have been done by mining companies, and few if any of the results have been published. Three gravity surveys have been made in the Iron River-Crystal Falls area,' " one by the U. S. Bureau of Mines, with inconclusive results, and the other two by Radar Exploration Co. for the Cleveland-Cliffs and the M. A. Hanna companies, with results not known to the writers. Both the last-mentioned surveys were detailed investigations, the stations being spaced as close as 10 ft along traverses,' and were made to determine the feasibility of locating iron ore by gravitational methods. Because of the presence of a large body of ore already extensively drilled, Dr. Harold L. James of the U. S. Geological Survey, Iron River, Mich., suggested that a further test of gravitational methods of exploration be made in the Round Lake area of Iron County, see Figs. 1 and 2. This survey indicated a considerable regional gradient and led to a study of the surrounding gravity field and its relation to the major structural features of the syncline within which the iron formation lies. The southwestern part of Iron County presents a series of hills and hollows elongated in a roughly north-south direction. The bedrock topography is of pre-glacial origin. Relief is moderate; a maximum elevation difference of approximately 350 ft was observed during the survey. Major drainage is dendritic with the larger streams: the Brule to the south, the Paint to the north, and the Iron in the central part. Hills are thickly grown with hard- woods, and lowland areas, not under cultivation, are usually covered by second-growth softwoods. The area covered in this paper includes the southern half of Iron County, Mich., with a deep synclinal basin occupying the central part of the area, and the southeast corner of Gogebic County, immediately to the west of Iron County. The upper Huronian iron formation, slates, and graywackes which form the synclinal basin rest upon a greenstone basement. The basin has not been completely outlined by exposures, drill records or other means, as outcrops are scarce and the thick mantle of glacial drift makes geological investigations extremely difficult. Glacial drift varies in depth up to 300 ft or more. The drift is usually thickest under the hills and is thinnest in the depressions and along drainage courses where most of the bedrock exposures occur. The area over which gravity investigations were made is almost, entirely covered by glacial material. Bedrock of the basin consists of a complexly folded series of iron formation, slates, and graywackes. One of the series of slates has a high magnetic susceptibility due to the fine-grained magnetite it contains. This formation can be detected readily. by magnetic methods and provides a marker horizon which can be easily followed. The magnetic slates are stratigraphically above the iron formation, and much of the geological interpretation of the area is based upon the magnetic anomalies they produce.

Jan 1, 1953

By L. O. Bacon, D. O. Wyble

THERE has been considerable speculation among mining geologists and mining men in general as to the relative merits of gravity methods in iron-ore exploration. Most of the investigations which have been carried out in recent years have been done by mining companies, and few if any of the results have been published. Three gravity surveys have been made in the Iron River-Crystal Falls area,' " one by the U. S. Bureau of Mines, with inconclusive results, and the other two by Radar Exploration Co. for the Cleveland-Cliffs and the M. A. Hanna companies, with results not known to the writers. Both the last-mentioned surveys were detailed investigations, the stations being spaced as close as 10 ft along traverses,' and were made to determine the feasibility of locating iron ore by gravitational methods. Because of the presence of a large body of ore already extensively drilled, Dr. Harold L. James of the U. S. Geological Survey, Iron River, Mich., suggested that a further test of gravitational methods of exploration be made in the Round Lake area of Iron County, see Figs. 1 and 2. This survey indicated a considerable regional gradient and led to a study of the surrounding gravity field and its relation to the major structural features of the syncline within which the iron formation lies. The southwestern part of Iron County presents a series of hills and hollows elongated in a roughly north-south direction. The bedrock topography is of pre-glacial origin. Relief is moderate; a maximum elevation difference of approximately 350 ft was observed during the survey. Major drainage is dendritic with the larger streams: the Brule to the south, the Paint to the north, and the Iron in the central part. Hills are thickly grown with hard- woods, and lowland areas, not under cultivation, are usually covered by second-growth softwoods. The area covered in this paper includes the southern half of Iron County, Mich., with a deep synclinal basin occupying the central part of the area, and the southeast corner of Gogebic County, immediately to the west of Iron County. The upper Huronian iron formation, slates, and graywackes which form the synclinal basin rest upon a greenstone basement. The basin has not been completely outlined by exposures, drill records or other means, as outcrops are scarce and the thick mantle of glacial drift makes geological investigations extremely difficult. Glacial drift varies in depth up to 300 ft or more. The drift is usually thickest under the hills and is thinnest in the depressions and along drainage courses where most of the bedrock exposures occur. The area over which gravity investigations were made is almost, entirely covered by glacial material. Bedrock of the basin consists of a complexly folded series of iron formation, slates, and graywackes. One of the series of slates has a high magnetic susceptibility due to the fine-grained magnetite it contains. This formation can be detected readily. by magnetic methods and provides a marker horizon which can be easily followed. The magnetic slates are stratigraphically above the iron formation, and much of the geological interpretation of the area is based upon the magnetic anomalies they produce.

Jan 1, 1953

By LeRoy Scharon, P. Uhley

TEST gravity surveys were made in the Washington County barite district of Missouri on properly owned by the Baroid Sales Division of the National Lead Co. This property is located just northeast of Richwoods in the northeastern corner of Washington County, Fig. 1. The area to which the surveys were confined comprised approximately 5000 acres, of which some 525 acres were surveyed gravitationally. Gravity observations were made at 2600 points within the area, observations being confined to relatively clear and gently sloping ground. Part of the area was heavily wooded, and the terrain too rugged for either the occurrence of a commercial barite deposit or a feasible gravity survey. The relief along the central drainage, Ditch Creek, was about 140 ft, the maximum difference in elevation being 400 ft in a distance of 3½ miles. The purpose of the test gravity survey was to determine whether the gravity method of geophysical prospecting might be applied in the exploration for barite deposits in the Washington County barite district, since a satisfactory systematic procedure had not been devised to explore and ultimately determine barite ore reserves with desired accuracy. No previous geophysical work with respect to barite is known to have been done in this area. Stratigraphy: The formations over which the barite deposits occur' are Paleozoic in age, representing rocks involving sandstones and dolomites unconformably underlain by pre-Cambrain granites and rhyolite porphyries. The areas covered by the granite survey were directly underlain by almost

Jan 1, 1955

By W. B. Agocs

IN August 1954 a low altitude test geophysical survey was made in the Green Pond area of Morris County, New Jersey, with a Gulf Research and Development Co. Model II total magnetic field variation magnetometer mounted in a Sikorsky S-55 helicopter. The test was made in this area to compare the results of a high precision, very low altitude magnetometer survey with an existing ground magnetic survey in this area having known magnetite concentrations, so that the method could be used in areas of difficult access for the detailing of airborne magnetometer anomalies of interest in place of ground surveys. The load capacity of the Sikorsky S-55 permitted installation of a recording scintillation counter so that a radioactivity survey would be made simultaneously with the magnetometer survey. The area surveyed is located at approximately 41°00'N and 74o28'W, just south and east of the town of Green Pond, N. J. The outstanding topographic feature of the region is Copperas Mountain, a well defined ridge, maximum elevation 1222 ft, which runs the entire length of the survey. The lowest point in the survey, 810 ft, is in the extreme eastern corner. Topography of the area is shown in Fig. 1. The three major rock units outcropping in the area are all metamorphic: the Pochuck gneiss, which has been divided into two metamorphic facies; the Byram gneiss; and the Green Pond conglomerate. The relative ages of the Pochuck and Byram formations, both pre-Cambrian, are in doubt, but it is believed that the Pochuck is the older of the two.' The Green Pond conglomerate is Silurian.' Distribution of the outcrops and mine locations is shown in Fig. 1. Two facies of the Pochuck gneiss can be distinguished locally—the Copperas Mountain and Kitchell members. The Copperas Mountain member is a hornblende gneiss, and all the mines and prospects in the area are in this unit. The Kitchell is a quartz-plagioclase feldspar gneiss. The Byram gneiss is a relatively nonresistant valley formation which is high in the potash feldspar. The Green Pond conglomerate is a well indurated quartzite-conglomerate which forms the Copperas Mountain and the Green Pond Mountain's ridge to the north. It overlies the gneisses with a strong angular discordance that may be a fault. The geologic structure of the Green Pond area is relatively uncomplicated. The foliation planes of the gneisses dip steeply to the southeast, and the Green Pond conglomerate dips steeply to the northwest. Additional faulting in the area is indicated at the contact between the Kitchell member of the Pochuck and the Byram along the base of the topographic spur extending to the southeast from Copperas Mountain. The magnetite mines of Pardee, Winter, Davenport, Green Pond, Copperas, and the Bancroft shaft are described by Bayleyl and Stampe2.' The ore is in the Copperas Mountain member of the Pochuck gneiss. The magnetite veins are 10 to 50 ft wide and up to 300 ft long, dipping to the southeast at angles ranging from 40" to 75". The locations of these mines are shown in Fig. 1. Dip Needle Survey: The dip needle survey shown in Fig. 2 was taken from a U. S. Bureau of Mines Report of Investigations." The figure numbers below the local, individual map area outlines refer to the figures in the aforementioned reports which were not contoured. The area of the dip needle survey was confined almost exclusively to the outcrops of the Pochuck gneiss. The separation between survey profiles was 100 ft and the distance between stations on the profiles was 25 ft in highly anomalous zones to 100 ft in magnetically flat areas. A total of 16 1/2 miles of traverse was surveyed over an area of approximately 1/2 sq mile with 2050 stations. The magnitude of the magnetic anomalies is difficult to determine due to the lack of information concerning the type of dip needle used and the procedure followed in making the dip needle survey. This latter would include the method of "zeroing" the dip needle and the procedure of reading at the stations, whether on the swing or statically. Calibrations made of the Gurley dip needle, Lake Superior type, show a static sensitivity of 385 gamma per degree in the range from —25" to +35o, corresponding to a variation in the total field of —9600 gamma to +13500 gamma in a total field of 57000 gamma, inclination 72". The sensitivity increases to 16 gamma per degree from a deflection of 60" to 76", and from 76" to 172" the sensitivity decreases continuously to a low of 260 gamma per degree. From the above it may be seen that it is difficult to assign an arbitrary sensitivity for the dip needle used on this survey. However, an estimated value of 100 gamma per degree may be assigned. On this basis, the majority of the magnetic anomalies, whose deviation is +20°, would be 2000 gamma. Locally, west and northwest of the Pardee mine the magnetic anomaly is +50°, or 5000 gamma; in the Green Pond mine area deviations of +75" are observed that would correspond to anomalies of 7500 gamma. The areal extent and width of the dip needle magnetic anomalies is comparable to profile and station spacing. Hence it is concluded that part of the detail may be due to control, and the probable cause of the magnetic anomalies is at or near surface exposures of magnetite concentrations in the form of veinlets and disseminations whose locations correspond to the local magnetic anomalies. On the basis of the magnetics, none of the magnetite concentra-

Jan 1, 1956

By H. Bloom, H. E. Hawkes

STREAMS and rivers are the principal channels into which the weathering products of rocks and their contained ores are funneled. The inorganic load of a stream system is a crude sample of all the earth materials in the drainage basin of the stream, and the heavy mineral assemblage of sediments is one of the oldest and most successful guides to certain kinds of bedrock ore in unexplored terrain. Early application of this method was made possible by the ease of separation and identification of heavy minerals in the field with the simplest equipment. Water analysis for traces of base metals became a practical possibility about eight years ago with the development of rapid chemical tests that could be carried out at the field site.' , Since that time the water method has been widely used in mineral reconnaissance, and a substantial number of discoveries have been reported. Here again, the techniques developed for this work were relatively simple and could be performed easily at the field site. Sediment analysis by chemical methods, as distinguished from mineralogical, has received less at- tention. Some experimental work was done by Lovering and others," but to the authors' knowledge, chemical analysis of sediment samples has not been used in routine exploration programs until very recently. In spite of the obvious promise of this method, it was not pursued vigorously because of the lack of a simple and portable chemical test that could be used conveniently at the field site or in a field camp. Procedures that had been developed for trace analysis of soils all called for a rigorous chemical attack with hot acids—tests more conveniently applied in processing large volumes of routine soil samples at an established field headquarters. Recently an extremely rapid and simple test was developed by Bloom.4,5 The extractant used in this procedure is a cold solution of ammonium citrate. Elements measured are the heavy metals, principally zinc, lead, and copper. This method differs from the established procedures for soil analysis in that it measures only a small fraction, about 5 pct, of the total metal content of the sample. It has been found, however, that the significant pattern of metals in the sediments of streams below a base-metal deposit can be brought out as well and sometimes better by this simple cold-extraction procedure than by the more tedious methods requiring hot acids. To understand fully the significance of the relation between the readily extractable and the total

Jan 1, 1957

By R. D. Russell, R. M. Farquhar

SOTOPIC tracers have become an important aid in following the progress of chemical processes in the laboratory. It has recently been found possible to utilize a system of naturally existing iso-topic tracers to obtain information about the geological history of lead ores. Common lead, such as is found in lead deposits, is a mixture of four stable isotopes having atomic weights 204, 206, 207, and 208. Of these, the last three are identical with the lead isotopes produced as stable end products of the radioactive decays of uranium and thorium: the first, lead-204, is not known to be produced on the surface of the earth by any process. Since uranium and thorium Occur in the surface regions of the earth in amounts comparable with lead, and since the half-lives of uranium and thorium isotopes are of the same order as the age of the earth, they produce the radiogenic lead isotopes in amounts comparable to the amount of nonradiogenic lead present. Every significant exposure of a sample of lead to uranium and thorium will therefore lead to the permanent alteration of the lead isotope ratios in that sample. It is this unique property of lead that serves as a means of tracing the history of a lead sample in terms of its contacts with the radioactive elements. If lead from a lead mineral has been analyzed with a mass spectrometer, the measured isotope ratios are determined entirely by the isotope ratios of primeval lead, which are identical for all minerals, and by the particular history of the sample. It follows that for samples from any particular geological area, observed differences in the isotopic composition are enough to distinguish different geological histories. An illustration of the qualitative application of this statement is given in Table I by analyses of some galenas from the western Cordillera. Samples from deposits in Pre-Cambrian sediments have very different lead isotope ratios from those of the ores in the Paleozoic sediments. Although the two types are associated closely geographically, it is apparent that they have had quite different histories and have probably been emplaced at quite different times, as the ideas outlined in the following section suggest. Even when applied quantitatively, a lead isotope analysis can never indicate a unique history of any lead sample. However, it greatly restricts the choices available and combined with other geological and geochemical data can lead to a much better understanding of the genesis of lead ores. General Character of Lead Isotope Variations: Early isotopic analyses of common leads by Nierl showed that geologically younger leads were generally richer in isotopes of masses 206, 207, and 208, with respect to that of mass 204. This regularity of measured lead isotope ratios can be easily observed by plotting each of the ratios Pb207/Pbm and Pb205/ Pb204 against the ratio Pb206/Pb204. In both graphs the points lie scattered closely about a well defined mean curve. It was immediately supposed that this regularity resulted from the growth of all leads from a common primeval lead present at some time, To, early in the earth's history. Lead in the outer part of the earth would become continually enriched in the radiogenic isotopes as a result of the uranium and thorium intimately associated with it. The subsequent extraction of some of this lead and formation of a lead mineral free of the radioactive parents provide samples of lead existing in the earth at the time of mineralization, T. Younger leads in general will be richer in the radiogenic isotopes because they have been associated with uranium and thorium for a longer time. Then lead ratios would be given by the formulae: (Pb206/Pb204)YTPb^/Pb204) +f "(u201) kdt T (Pb207Pb204)r = (Pb208/Pb204)T0 + J (U295/Pb204) k' dt T (Pb208/Pb204) t = (Pb208Pb204 + J (Th204) A." dt [1] where A, A', and A" are the decay constants of U238, U285 and Th232. Summaries of measurements of radioactivity of surface rocks, such as given by Faul,2 are of limited

Jan 1, 1958

By G. W. Gross

A commercial deposit of white kaolinite clay contained in the sandy overburden of the Cambrian Gatesburg formation in Central Pennsylvania was successfully mapped by combined SP and resistivity methods and results were checked by drilling. Resistivity minima in the range between roughly 2000 and 3500 ohm-meters coupled with second-order SP maxima of 50-60 mV contrast were found to characterize commercial white kaolinite clay beneath not more than 30-40 ft. of sandy overburden in the area stdied. This investigation supports the hypothesis, established previously, that certain SP phenomena may reasonably be ascribed to diffusion and membrane potentials produced by interaction of clay lenses, sandy matrix, and ground waters. The success of this test proves that this prospecting technique can assist in locating clay deposits in sandy overburden derived from the weathering of sandstones and carbonate rocks such as the Cambrian formations of Central Pennsylvania. In a recent paper, Gross and Moore (1959) described broad self-potential minima above the outcrops of the Cambrian Gatesburg formation. These "first-order" SP anomalies, of 220-350 mV contrast (Figure 7), are related to the peculiar sandy residual soil covering the Gatesburg formation. Small positive ("second-order") peaks of 50-60 mV contrast are superposed on the bottom or flanks of the first-order troughs. They appear to be related to lenses and layers of kaolinite clays within the sandy Gatesburg overburden. Both first-order and second-order anomalies show a characteristic inverse relationship with apparent resistivity profiles in most cases. An explanation in terns of liquid-junction and shale potentials was advanced. According to this working hypothesis, shale potentials are generated: 1) at the contact of the sandy Gatesburg overburden with the more argillaceous soils of surrounding formations; 2) at the boundary of clay lenses contained in the sandy matrix of that overburden. Concentration gradients between interstitial infiltration waters and perched water tables within the Gatesburg overburden are believed to give rise to the liquid-junction potentials. In order to test this hypothesis further, a detailed study was carried out of a second-order positive anomaly on the property of the Woodbury Clay Co. at Mines (Blair County, Pa., Hollidaysburg folio of the U.S. Geological Survey). A second aim was to establish if combined SP and resistivity surveys are suitable as a practical method for delimiting favorable areas in which commercial kaolinite clay de~osits may be found by drilling. Drilling control was provided by the Woodbury Clay Co. PROCEDURES Instrumentation used for SP measurements was the same as described in the paper mentioned. For resistivity surveys, a direct-current voltmeter-ammeter device built by Georator Gorp. of Manassas (Va.) was used in combination with non-polarizing electrodes from the same manufacturer. Power was supplied by one to six 45-volt, heavy-duty B-batteries

Jan 1, 1961

By Charles R. Holmes

MORE than 70 igneous pipes and dikes are known to occur in Cambrian sediments throughout an approximately circular area of about 75 sq miles in southwestern Ste. Genevieve County and southeastern St. Francois County, Mo., across the southern portion of the Farmington anticline, which is outlined in fig. 1. From evidence obtained from fossil fragments taken from some of the in-trusive~, and from the similarity in composition of the more basic intrusives to those of known age in surrounding states, these pipes and dikes are believed to be at least post-Devonian and probably Cretaceous in age. As first postulated by Rust,' these intrusives are believed to represent explosion tubes, or diatremes, punched through great thicknesses of solid rock by gaseous pressure. The particular intrusive studied is located about 1 mile north of the small town of Avon at an elevation of 880 ft in the EVz SEy4 NEY4 of see. 2, T. 35N, R. 7E. Outcrop is through the Bonneterre dolomite in two separated exposures. The larger outcrop extends east and west for about 50 ft along a tributary in a small ravine (fig. 2). The smaller exposure occurs as a few scattered patches over an area 20 ft square about 100 ft to the north. The area between the exposures is covered, but scattered patches of the Bonneterre dolomite outcrop throughout the area surrounding the diatreme. Where exposed, contact relations show the surrounding dolomite to be shattered and metamorphosed to a fine-grained rock for a distance of 15 to 20 ft from the intrusive. The igneous rock occurs as a dark greenish-gray porphyry near the center of the diatreme and as a fine-grained, greenish-gray material containing lapilli and metamorphosed fragments of dolomite near the contact with the country rock. The most abundant original mineral of the porphyritic rock is olivine now largely serpentinized as the result of extensive hydrothermal alteration at time of emplacement. The most common constituent of the fine-grained rock, which occurs near the border of the intrusive, is calcite. Mica is a common constituent of both types of rock, occurring as tufts or flakes. Magnetite makes up about 2 pct of the diatreme and occurs as small irregular grains or streaks of tiny grains. Singewald and Milton' have termed the rock of this body an "augite-free alnoite." Susceptibility measurements of pulverized specimens were made from selected samples taken from both the diatreme and the surrounding country rock. The susceptibility of the Bonneterre dolomite was found to be less than 40xlO-6 cgs (centimeter-gram-second) units and that of the metamorphosed contact dolomite less than 200x10-6 cgs. Measurements of individual samples of the igneous rock showed a wide variation in susceptibility between limits of 1000x10-6 cgs to 8000x10-6 cgs, with the maximum difference occuring in samples taken only a few feet apart. The maximum value was exhibited by a highly weathered sample taken from the northern outcrop, while minimum susceptibility was determined from a partially weathered sample taken only a few feet away. These extremes are believed to represent small local concentrations of stringers and grains of magnetite crystals in the igneous rock. A detailed magnetic survey of the horizontal and vertical components of the earth's magnetic field was made over the diatreme area. Stations were occupied at 20-ft intervals as shown by the grid on fig. 2. When greater detail was desired, intervening stations were also occupied. The field instruments were supplied by the Department of Geophysics, St. Louis University. The magnetometers are the Schmidt balance type constructed by the Ruska Instrument Co. These instruments are temperature compensated and have a standard sensitivity of 10 gamma. Calibration of the instruments

Jan 1, 1951

By Charles R. Holmes

MORE than 70 igneous pipes and dikes are known to occur in Cambrian sediments throughout an approximately circular area of about 75 sq miles in southwestern Ste. Genevieve County and southeastern St. Francois County, Mo., across the southern portion of the Farmington anticline, which is outlined in fig. 1. From evidence obtained from fossil fragments taken from some of the in-trusive~, and from the similarity in composition of the more basic intrusives to those of known age in surrounding states, these pipes and dikes are believed to be at least post-Devonian and probably Cretaceous in age. As first postulated by Rust,' these intrusives are believed to represent explosion tubes, or diatremes, punched through great thicknesses of solid rock by gaseous pressure. The particular intrusive studied is located about 1 mile north of the small town of Avon at an elevation of 880 ft in the EVz SEy4 NEY4 of see. 2, T. 35N, R. 7E. Outcrop is through the Bonneterre dolomite in two separated exposures. The larger outcrop extends east and west for about 50 ft along a tributary in a small ravine (fig. 2). The smaller exposure occurs as a few scattered patches over an area 20 ft square about 100 ft to the north. The area between the exposures is covered, but scattered patches of the Bonneterre dolomite outcrop throughout the area surrounding the diatreme. Where exposed, contact relations show the surrounding dolomite to be shattered and metamorphosed to a fine-grained rock for a distance of 15 to 20 ft from the intrusive. The igneous rock occurs as a dark greenish-gray porphyry near the center of the diatreme and as a fine-grained, greenish-gray material containing lapilli and metamorphosed fragments of dolomite near the contact with the country rock. The most abundant original mineral of the porphyritic rock is olivine now largely serpentinized as the result of extensive hydrothermal alteration at time of emplacement. The most common constituent of the fine-grained rock, which occurs near the border of the intrusive, is calcite. Mica is a common constituent of both types of rock, occurring as tufts or flakes. Magnetite makes up about 2 pct of the diatreme and occurs as small irregular grains or streaks of tiny grains. Singewald and Milton' have termed the rock of this body an "augite-free alnoite." Susceptibility measurements of pulverized specimens were made from selected samples taken from both the diatreme and the surrounding country rock. The susceptibility of the Bonneterre dolomite was found to be less than 40xlO-6 cgs (centimeter-gram-second) units and that of the metamorphosed contact dolomite less than 200x10-6 cgs. Measurements of individual samples of the igneous rock showed a wide variation in susceptibility between limits of 1000x10-6 cgs to 8000x10-6 cgs, with the maximum difference occuring in samples taken only a few feet apart. The maximum value was exhibited by a highly weathered sample taken from the northern outcrop, while minimum susceptibility was determined from a partially weathered sample taken only a few feet away. These extremes are believed to represent small local concentrations of stringers and grains of magnetite crystals in the igneous rock. A detailed magnetic survey of the horizontal and vertical components of the earth's magnetic field was made over the diatreme area. Stations were occupied at 20-ft intervals as shown by the grid on fig. 2. When greater detail was desired, intervening stations were also occupied. The field instruments were supplied by the Department of Geophysics, St. Louis University. The magnetometers are the Schmidt balance type constructed by the Ruska Instrument Co. These instruments are temperature compensated and have a standard sensitivity of 10 gamma. Calibration of the instruments

Jan 1, 1951

By W. E. Wickerham

THE Magnetic Storm Monitor is an instrument that continuously records variations in the earth's total magnetic field at a fixed location. It is intended for use in conjunction with airborne magnetometer surveys. There are stormy periods when changes in the earth's magnetic field are so violent that data obtained with airborne equipment would be of little value. The Monitor provides this information so that flights may be cancelled or terminated, thus eliminating useless flying. Moreover, when some unpredictable change in the earth's field occurs during an airborne survey, the Monitor record, showing a similar event, may serve to salvage the data. The utility of a base instrument is determined largely by its physical dimensions, power requirements, stability, and reliability. This instrument is small enough to be transported in any powered vehicle. It will operate from either a 110 v, 60 cycle power line or from an inverter powered by an automobile battery. The development of an electronic feedback circuit that measures the magnetic field strength and a fabricated buckout magnet having essentially zero temperature has contributed to instrument stability and reliability. A tripod supporting the magnetometer head, a chassis housing all electronic components, and an Esterline Angus Recorder comprise the equipment, shown in Fig. 1. The vibrator-type inverter shown is used when a 110 v, 60 cycle power line is inaccessible. Approxi- mately 60 w are required to operate the instrument and the circuit is insensitive to reasonable power line voltage changes or transients. The head unit contains a fluxgate-type magnetometer element and a special magnet mounted on a ceramic structure. Since this magnet is used to buck out most of the earth's field, adjustments are provided for properly positioning the magnet with respect to the element. This assembly is mounted in such a way that the element can be oriented into the total field. Fluxgate Element: The heart of the Storm Monitor is a fluxgate-type magnetometer element. The ability of this unit to detect changes in magnetic fields has been covered at length in the literature.1, 2 For this discussion it will suffice to say that the Gulf

Jan 1, 1956