Search Documents

By R. V. Ramani, J. Qin

During the mining process, the in-situ material is broken into different size ranges, from very large pieces to very fine particles. Some of the fine particles become airborne. In underground coal mining, airborne respirable dust is associated with health and safety of the miners. The amount and size distributions of airborne dust are important parameters to effective dust control measures. The design of underground mine experiments, including sampling procedures and sample analyses methods to determine these parameters are presented in this paper. A total of fifteen continuous miner cuts were sampled. The amount of dust generated during the cutting process and the relationship between total and respirable airborne dust concentrations and amounts are examined. The amount of respirable dust airborne is on the average only 0.016% of the respirable dust generated. On the average, 61% of the total airborne dust measured is in the respirable size range. The amount of respirable airborne is on the average 36% of the respirable size fraction in the total airborne dust. For equal proportion of rock and coal material cut, rock contributes about twice as much fines (=0.22 mm) as coal. Additional fundamental research is necessary to further the understanding of the airborne propensity of respirable dusts in mine atmospheres.

Jan 1, 1989

By Alan D. Randolph

INTRODUCTION The production of fines is an unwanted side-effect in most crystallization processes. The definition of “fines" is relative to the size of the desired product and varies from <30 mesh for coarse KC1 fertilizers to subsieve organic material produced by salting-out pro- cesses. Sometimes a well-developed fines distribution is necessary in the production of large crystals, e.g. the fines removal stream from a potash crystallizer. The production of fines is usually not desired in a crystallization separation step. However, product purity can either improve or degenerate with a decrease in crystal size depending on the relative importance of product washing vs mother liquor occlusions in determining over-all purity. Typically, both washing efficiency and mother liquor occlusions decrease with decreasing particle size. Fine crystal distributions have historically been difficult to measure and categorize; however this situation is changing rapidly with the use of electronic particle counters of the electrical zone- sensing or light scattering type. In fact, fine-crystal measurement is perhaps the key to better understanding and control of coarse- crystal crystallization processes. The fine-crystal distribution carries much useful information from which nucleation and growth rates can be inferred. The purpose of this paper is to briefly discuss a few crystallization processes in which production and/or measurement of fines is important and to categorize the process conditions which yield a fine- crystal product.

Jan 1, 1980

By D E. Tennant

In the fields of geotechnical engineering and slope management, various software packages are used to assess the behaviour or propensity for a slope to fail. Traditional kinematic analysis calculates the probability of failure of design sectors with respect to dominant structural set orientations. A novel methodology is provided here to view potential hazardous slope behaviour in 3D, allowing engineers to make informed decisions regarding various pit slope geometries. Apparent dips are calculated for every point in space with respect to every slope orientation of the entire pit surface/design, specifically in reference to bench and inter-ramp planar failure mechanisms. Implementing a proactive approach to slope design will not only lead to early mitigation of risk but can also add direct value by enhancing or improving upon slope angles for earlier access to ore. From a safety perspective, identification of unfavourably oriented slope geometries can be dealt with before failure occurs. This methodology relies on a strong understanding of the existing rock mass anisotropy, particularly behind the face, thereby removing some of the uncertainty surrounding pit design as well as presenting engineers with an additional means to manage risk.

Nov 29, 2022

By F. Awotwe-Appiah, P. Koshy, J. Dankwah, J. R. Dankwah

This research investigates the generation of an effective carbonaceous material from waste ‘pure water sachets’ and their subsequent utilisation as reductants for the reduction of the Opon Mansi iron ore. Composite pellets of Opon Mansi iron ore and pulverised carbonaceous material generated from waste pure water sachets were heated from room temperature to 1200 °C in a gas fired furnace for seventy minutes. The reduced pellet was analysed chemically for its oxygen and carbon content using a LECO Oxygen/Nitrogen and LECO Carbon/Sulphur analysers, respectively. It was observed that nuggets of metallic iron were readily produced with the carbonaceous materials acting as an effective reductant and source of chemical energy. XRD analysis of waste ‘pure water sachets’ revealed that the polymer was semi-crystalline with peaks that were identical to those of high density polyethylene (HDPE). Gas emission behaviour of the iron ore-PWS pellet was studied in a horizontal tube furnace at 1200 °C using an infrared gas analyser; the results revealed an exhaust gas rich in the reducing gases CO and CH4 along with CO2.

Jan 1, 2015

By R. Bhaskar, H. Xie

Fractal theory was horn in the mid-1970s. Since then, its application has been spreading day by day, from mathematics and geology to areas such as geophysics, physics and material sciences. In this paper, fractal models are developed to characterize particle size distribution and surface area. Theoretical formulas are derived for the computation of fractal dimensions D (size) and D[s] (surface area). The models developed are applied using experimental data of particle size distribution and surface area obtained from the Microtrac Particle Size Analyzer for dust processed by several size reduction devices. The theoretical models and the experimental data are found in good agreement. The fractal dimensions obtained are D = 1.350 to 1.770 and D[s] = 2.058 to 2.584 for fine coal dust particles (< 15 µm) produced by various size reduction mechanisms. The physical meaning of these fractal dimensions is also related to the dust generation processes.

Jan 1, 1994

By N. S. Dalal, V. Castranova, X. Shi, W. Wrr, V. Vallyathan

"SUMMARY Data presented here indicate that freshly fractured silica exhibits surface characteristics and biologic reactivity distinct from aged silica, and on this basis we propose that these surface features may lead to enhanced manifestations of lung Injury. Grinding of silica produces ~10"" Si and SI-O (silicon-based) radicals per gram of dust on the particulate surface which are characterized by an electron spin resonance (ESR) spectrum centered around g = 2.0015. These silicon-based radicals react with aqueous media to produce OH radicals, which are demonstrable using a DMPO spin trap. The concentration of silicon-based radicals in silica decreases with aging in air and exhibits a half-life of ~30 h, whereas its ability to generate OH radicals in aqueous solution decreases with a half-life of ~20 h. However, on storage in aqueous media, the concentration of silicon-based radicals end the dust's ability to generate OH radicals decrease significantly within a few minutes. Freshly ground silica is also more biologically reactive than aged silica, because freshly crushed silica activates a greater respiratory burst In alveolar macrophages than aged silica, i.e., storage of ground dust in air decreases silica-Induced superoxide anion secretion, hydrogen peroxide release, and NBT reduction by 25%, 68%, and 43%, respectively. Furthermore, compared to aged silica, freshly ground silica exhibits a greater cytotoxic effect on cellular membrane Integrity, i.e., a 1.5-fold increase in LDH release from macrophages, a 36-fold increase in hemolytic activity, and a three-fold increase in the ability to induce lipid peroxidation. Because acute silicosis is frequently associated with occupations in which freshly fractured crystalline silica of respirable size is generated, the present study suggests that fracture-generated silicon-based radicals may play a significant role in the pathogenesis of this disease. AM REV RESPIR DIS 1955; 133:1213-1218IntroductionOccupational exposure to crystalline silica can be associated with either chronic or acute pulmonary disease. Chronic silicosis becomes manifest 20 to 40 years after first exposure and is characterized by development of concentric hyalinized nodular lesions in the lung with the de-velopment of dyspnea over a period of several decades. Acute silicosis, on the other hand, is manifested by a rapid on-set after exposure and is characterized by the accumulation of an amorphous granular lipoprotein exudate in the airspaces and rapid development of respiratory disability within a few years (1-3).Information is growing concerning the etiology of chronic silicosis. Studies sug-gest that several mechanisms may be in-volved in the development of fibrosis. Lung injury may result from silica-induced release of lysosomal enzymes from alveolar macrophages (4, 5). In ad-dition, silica-induced activation of su-peroxide anion and hydrogen peroxide release from alveolar macrophages may result in oxidant-induced damage to lung parenchyma (6). Silica exposure can also result in the release of mediators from alveolar macrophages which enhance the proliferation of fibroblasts and the syn-thesis of collagen by these pneumocytes (7, 8)."

Jan 1, 1988

By X. Shi, K. S. Kaspnak

"The generation of free radicals from reactions of nickel (Il)-thiol complexes with molecular oxygen and model lipid hydroperoxides was investigated by electron spin resonance (ESR) utilizing 5,5-dimethyl-1-pyrroline-N-oxide (DMPO) as a spin trap. Incubation of nickel (II) [Ni(II)) with cysteine in an aerobic environment generated hydroxyl (·OH) radical, which then reacted with cysteine to generate a carbon-centered alkyl ( · R) radical. Radical generation was inhibited under a nitrogen atmosphere. Model lipid hydroperoxides, cumene hydroperoxide, and I-butyl hydroperoxide enhanced the yield of these radicals and also generated an alkoxyl (·OR) radical. Radical yield decreased by approximately half under a nitrogen atmosphere. Although histidine did not cause radical formation in the reaction between Ni(II) and cumene hydroperoxide under aerobic conditions, the addition of histidine to a mixture containing Ni(ll), cysteine, and cumene hydroperoxide under the same experimental conditions increased the yield of · R radical but lowered the yield of ·OR and ·OH radical adducts. It thus appears that histidine caused the ·OH attack to be more site-specific. Similar results were obtained utilizing 1-butyl hydroperoxide. Penicillamine or N-acetylcysteine yielded similar results except that under aerobic conditions, reaction between Ni(ll) and N-acetylcysteine without hydroperoxide did not generate a significant concentration of free radicals. Under the same experimental conditions, cystine did not generate any detectable free radicals, suggesting an important role of the -SH group in Ni(II)-mediated free radical generation. The results indicate that free radical generation from the reaction of Ni(Il)-thiol complexes and molecular oxygen, and/or lipid hydroperoxides, may play an important role in the mechanism(s) of Ni(II) toxicity and carcinogenesis. INTRODUCTIONWhile nickel is a well-recognized carcinogen [l, 2]. the underlying biochemical mechanisms remain unclear (3, 4). Recent studies suggest that these mechanisms may involve oxidative DNA damage through free radicals, especially the hydroxyl (•OH) radical [5-13]. The mechanisms of nickel carcinogenicity and toxicity may also involve lipid peroxidation [14-21]. Unlike ferrous ion [Fe(II)], the Ni(II) cation itself does not directly react with 02, H2O2, or lipid hydroperoxides to generate free radicals [12, 21]. However, it has been reported that Ni(II) complexes with certain synthetic oligopeptides, e.g., tetraglycine or glycylglycylhistidine, make Ni(II) reactive with 02. This reaction results in transitory formation of Ni(III) and degradation of the organic ligand via free radical reactions [22]. Such Ni(II)-peptide complexes are also capable of reacting with H2O2 to produce oxygen free radicals [11, 12]. Although the cellular environ¬ment may not contain these particular peptide ligands that are known to render Ni(II) redox active in vitro, it does contain a variety of oligopeptides that are capable of forming Ni(II) complexes at physiological pH, and thus may facilitate Ni(II) redox activity in vivo. These oligopeptides include glutathione (y-L glutamylycysteinylglycine), carnosine (homocarnosine (y aminobutyryl-L-histidine), and anserine ( B-alany1-3-methyl-L-histidine)."

Nov 1, 1995

By Jeong-Heum Kim, Jan M. Mutmansky, Y. J. Wang

The simulation of randomness in a system of components is important in certain types of systems analyses. This paper presents procedures for generating ventilation networks that are random in many of their characteristics and which can be used to study the performance characteristics of various mine ventilation network analysis procedures without introducing undue bias as a result of the nature of the network. Among the parameters of a network that affect the efficiency of a network analysis procedure are: (1) the interconnection pattern of airways, (2) the distribution of resistances in the network, (3) the number and location of fans, (4) the fan characteristic curve, (5) the size of the network (number of branches), and (6) the density of the network (number of nodes compared with the number of branches). In the procedures proposed here, a single fan with a fixed characteristic is used to simplify the problem and eliminate the fan as a source of variation. The resistances of the airways, the pattern of interconnection of the airways, and the fan location are randomly chosen in an attempt to eliminate the bias in the performance characteristics of the network analysis methods caused by these parameters. A method of generating biconnected networks while keeping the "randomness" of these other parameters is suggested. At the same time, the size and the density of networks are controlled to investigate their impacts on the performances of the network analysis procedures. The combination of these two variables has been termed the "level of complexity" of the network in this paper. Finally, a summary and conclusions section outlines some characteristics of the networks generated, using the random generation procedures outlined in the paper.

Jan 1, 1991

By Benedetto Corain

The production and dispersion of metal nanoclusters onto inorganic supports and amorphous carbon rest on well consolidated technologies belonging to the realm of industrial catalysis and of basic catalysis research (1). In spite of the existence of a variety of specific synthetic strategies, their very rationale relies on three main approaches i. e.: A: precursors of both the metal nanoparticles and of the relevant supports (or the support itself) are intimately mixed (even let to react) at ambient conditions and then thermo-reduced according to very controlled protocols (2); B: precursors of metal nanoclusters are let to be adsorbed onto suitable supports from the gas or liquid phase and subsequently thermally decomposed (3); C: metastable size-controlled metal nanoclusters are previously generated in a liquid medium and subsequently transferred onto pre-formed support particles (4). The production and dispersion of metal nanoclusters onto organic soluble supports is also a rather well documented academic praxis (5, 6, 7, 8) able to provide e.g. size-controlled Au0 nanoclusters of 4.4±1.7 nm (5). Our group started in 1997 developing (9) an innovative approach to the synthesis of metal nanoclusters dispersed inside insoluble, albeit accessible (see below) mechanically robust gel-type resins (10), which procedure was tested so far on palladium metal. Metal ions are previously dispersed upon ion-exchange inside of the polymer framework, followed by chemical reduction and by the aggregation of born metal atoms into nanoclusters, the size of which is templated (11, 12) by the three-dimensional intercommunicating meshes that build up the overall polymer framework (Figure 1).

Oct 1, 2003

By J. A. Finch, Zhenghe Xu, Z. A. Zhou

Whether the microscopic bubbles generated by the high energy dissipation and high feed-slurry velocities in new flotation cells are stable in solution and what roles they play in particle collection are of great interest for the flotation of fines. Experimental work has shown that, with fast flow of liquid through an orifice, stable microscopic bubbles can form in flotation systems by hydrodynamic cavitation in the absence of gas supersaturation. The minimum flow rate at which bubble formation is initiated varies from 8 to 15 m/s, depending on the design of the cavitation tube, which is within the range of feed slurry velocities of some newly developed cells. Feed aeration enhances the formation of micro-bubbles by hydrodynamic cavitation. The study suggests that the fast flotation kinetics of some new cells may be attributed in some degree to the formation of microscopic bubbles

Jun 21, 1905

By E. N. Durussel

"The Fox Mine has been producing copper/ zinc ore since 1970 at a rate of approximately one million tons per year, and until 1978all production was derived from longhole open stopes. In June 1978, a trial stope using bighole mining methods was started to eliminate the development of two sublevels between 400 level and surface. The trial proved to be successful, and bighole mining is now an accepted mining method for both stopes and pillars at Fox Mine.When production blasting was started in the first stope, the biggest problem encountered was the production of large amounts of sulphur dioxide gas as a result of secondary sulphide dust explosions. This gas generation resulted in lost production time and caused minor damage to underground installations to the blast level, and to the headframe. Sulphur dioxide generation has been noted in secondary drawpoint blasts and, on rare occasions, in drift rounds.This paper discusses the occurrence of the sulphur blasts and the practices and precautions used to prevent their reoccurrence at Fox Mine.IntroductionThe Fox minesite is located 30 miles southwest of Lynn Lake, Manitoba. With production startup in 1970, Fox Mine is owned and operated by Sherritt Gordon Mines Limited.The Fox orebody occurs as a large lenticular zone of semi-massive sulphides approximately 1,500 feet long and 15 to 100 feet wide running east and west. Dipping 70 degrees to the north, the orebody tends to bottom out at the 3200-foot level and reaches to within 15 feet of surface."

Jan 1, 1981

By Alexander V. Suvorin, Vladyslav M. Sokolov

"The traditional technologies for production of the coprecipitated and deposited catalysts are analyzed from the standpoint of diversion of application of the feedstock and increase of efficiency for its usage. The options for return of the metals of spent catalysts to the catalysts production are described. The novel environmentally friendly and cost efficient approach for reutilization of the spent catalysts is realized in practice. It anticipates application along with spent catalysts of the waste generated in the catalytic productions. Reutilization of the Ni-containing catalysts is referred as an illustration. Introduction The recent development of large catalytic manufacturing for organic and inorganic synthesis, and petroleum refinery as well as for applied environmental catalysis has brought about increase and diversification of catalysts production. The generation of spent catalysts has been increased correspondently. The feedstock for production of catalysts is mostly metals in a form of nitrates, carbonates, hydroxides, hydroxydcarbonates. Sometimes salts of organic acids, of ammoniates, of chlorides and of sulphates occur. All these materials are scarce and expensive. So their repeated use by reutilization of spent catalysts is very actual issue. The traditional recycling the Fe-, Cr-, Ni-, Cu- or Zn-containing spent catalysts are carried out by pyrometallurgical reclamation of pure metals or alloys. They can not be used directly in production of catalysts [1, 2]. The hydrometallurgical approach is used for recycling spent catalysts with PGM, W, Mo, Co, Ni or Cu. It provides production of salts of these metals in a form of sulphates, chlorides, carbonates, hydroxydcarbonates and sometimes nitrates or ammoniates. Only a limited number of these salts can be used directly in production of catalysts. Material losses during catalysts production The basic feedstock for manufacturing coprecipitated and deposited catalysts that may be produced from the spent catalysts is aqueous solutions of metals nitrates. Their production is based on application of nitric acid as a dissolvent. About half of it is lost with the flue gases in a form of nitrates vapor and nitrogen oxides (II, IV). The last compound is generated by reaction:"

Jan 1, 2008

By S Bandopadhyay

The seasonal fluctuations of the dust content in Arctic mine environments and the environmental variables affecting the intensity of dust production are qualitatively well known, but quantitative models that allow simulation and prediction of dust generation and the effects of engineering control of thermal regime on the mine environment are still non-existent. In Arctic mines, the migration of moisture in the surrounding rock mass releases fine dust by freeing it from the ice matrix allowing it to escape into mine airway. The migration of moisture is the direct cause for the production of mine dust and heat is the primary driving force. This paper examins the heat and moisture exchange between the ventilation air and the surrounding rock mass in frozen ground, placer mines in the Arctic. Based on the simulated results of a coupled heat and mass transfer problem with phase change, methods of dust control have been identified for mines in the Arctic.

Jan 1, 2005

By D. E. Martin, K. J. Hamill, H. J. Miller

1. INTRODUCTION In April 1979, the U. S. Nuclear Regulatory Commission issued the Draft Generic Environmental Impact Statement (GEIS) on Uranium Milling (NUREG-0511) for public comment. While the GEIS is a broad environmental impact assessment of the U.S. uranium milling industry as a whole, its primary focus is on the issue of uranium mill tailings disposal and long term isolation. In August of 1979, proposed regulations (U.S. Federal Register Notice 44FR50012), incorporating both conclusions of the GEIS and provisions of recent U.S. legislation on uranium mill tailings (Uranium Mill Tailings Radiation Control Act of 1978--UMTRCA), were also issued for public comment. This paper (1) briefly reviews the major conclusions of the draft GEIS, (2) summarizes the major elements and rationale of the associated, proposed regulations, and (3) reviews some of the major issues raised during the public comment period and changes which the NRC staff expects will be made in finalizing the GEIS and regulations. The risk in summarizing a document of such broad scope and complexity as the GEIS is that the depth of evaluation and the full technical bases for conclusions reached may not be adequately conveyed. Recognizing this, those Sections of the draft GEIS where a more complete discussion of the issues is presented are parenthetically noted in this paper in order to facilitate location of additional background and supporting material. 2. GENERAL CONCLUSIONS In the GEIS, a full range of tailings disposal alternatives was considered. These alternatives ranged from the past practice of doing little or nothing to control tailings, to advanced treatment alternatives such as nitric acid leaching to increase removal of radioactive elements and fixation of tailings in cement or asphalt. Our broad conclusions were: -Any alternative which results in the need for ongoing, active maintenance to assure long term containment, is unacceptable. (12.3.2.1) -Advanced treatment alternatives are unwarranted since they offer uncertain incremental benefits yet involve costs which may be as much as an order of magnitude greater than costs associated with acceptable alternatives. In addition, the advanced treatment

Jan 1, 1980

By Sven Petersen, Iain J. Stobbs, Bramley J. Murton, Paul A. J. Lusty

"INTRODUCTIONIt is widely thought that seafloor massive sulphide (SMS) deposits, the modern analogue of volcanogenic massive sulphide (VMS) deposits, present a potential global resource for base (Cu, Zn) and precious metals (Au, Ag). In addition, SMS deposits can be enriched in ‘critical metals’ including Se, Te, Tl [1], which are essential for use in the construction of modern and green technologies. Globally over 340 high temperature hydrothermal sites have been identified at a range of ocean spreading centres [2], significant massive sulphide deposit formation has been recorded at 165 of these sites [3].To date only 13 deep sea sulphide deposits have undergone intrusive investigation (drilling or coring) and of these, only 6 sites have published tonnage estimates [2]. Almost all research and drilling of SMS deposits has been focused on active systems, the investigation of the morphology, subsurface structure and mineralogy of hydrothermally extinct seafloor massive sulphide (eSMS) deposits is almost non-existent.As such, little is known about the mechanisms that operate post-SMS formation and which have an impact on the preservation and hence resource value of SMS. Identifying these generic processes and mechanisms, and the extent to which they impact the resource grade, is critical in evaluating the global potential of SMS."

Jan 1, 2017

By Raja V. Ramani, Robert L. Frantz

"The House/Senate Joint Conference Committee has instructed the Bureau of Mines to have the Advisory Committee on Mining and Mineral Resources Research review on an annual and simultaneous basis each generic mineral technology research center (GMTC). In order to accomplish that review promptly and uniformly, committee members have revised and approved an in-depth questionnaire. That document formed the basis of their review. The information provided by that questionnaire was an important factor in their recommendations concerning the future direction of the program; a presentation was made at the last National Plan Update.The comprehensive nature of the questionnaire and the scope of the information contained therein make it an excellent retrospective of the Center. Having a clear vision of where the Center has been and knowing where it is now will help guide it into the future. It is felt that such a detailed view of the Center's facilities and research program will be of value to Center personnel and Advisory Committee members.Each aspect of the questionnaire has been examined, answered in detail, and documented throughly. With the completed questionnaire as a guide, this volume examines the research program, Center personnel presently active on GMTC projects, number of graduate degrees granted with GMTC support, GMTC publications, degree of individual interaction, technology transfer, the reference center, GMTC equipment and facilities, and any envisioned plans for future research. It is hoped that this volume will serve as a review of the years 1984-1988, the first four years of the Center's operation."

Aug 31, 1989

"The mission of the Respirable Dust Center is to enhance the health, safety and productivity of the miners 'through advancing the fundamental .understanding of all aspects of respirable dust associated with mining and milling and the interaction of dus.t and lungs for reducing the incidence and severity of respirable dust disease. All Dust Center activities are focussed to be responsive to this mission which is shared by several federal agencies closely associated with the Generic Mineral Technology Center for Respirable Dust such as USBM, M,SHA, and NIOSH, and the mining industry. While significant progress has been achieved in making mine atmospheres cleaner and healthier, respirable dust disease remains the nations worst industrial hazard. GOALSThe goals of the Respirable Dust Center have been formulated to recognize the diverse scientific, engineering and medical aspects of respirable dust as well as the need to enhance the interaction, education and technology transfer in the respirable dust area.The Center goals are to:1. Enhance the understanding of the scientific, engineering and biological characteristics of fine and respirable mineral particles, fibers, organic aerosols, and complex particles found in the mining and milling atmospheres.2. Advance the understanding of the physical behavior of airborne respirable dust particles in flowing streams under different. stimuli during mining and milling.3. Advance fundamental understanding of the causative mechanisms for the occupationally related lung impairments and the airway diseases of mine and mill workers.4. Establish the relationship between natural and cultural factors (mine geology, mineralogy, mining and milling methods, equipment and control measures) in the generation, exposures, and pathogenic properties of fine particles.5. Contribute to the development of control mechanisms for reducing ambient respirable dust concentrations, worker exposure, the incidence and severity of dust related lung disorders and disease prevention in mining and milling atmospheres.6. Enhance functional integration among the various research personnel in the Center, as well as, with other groups, such as MSHA, NIOSH and USBM involved in respirable dust research and control.7. Develop technically trained personnel for employment in the mineral industry for respirable dust research and control.8. Enhance the availability of respirable dust-related information utilizing several technology transfer avenues."

Jan 1, 1990

"The Generic Mineral Technology Center on Respirable Dust was established in August 1983, at the request of the Bureau of Mines, to conduct research that affords ""...each miner the opportunity to work underground during the period of (his/her) adult working life without incurring any disability from pneumoconiosis or any other occupational disease"". The Center consists of the Mining and Mineral Resources Research Institutes (MRI) of The Pennsylvania State University (PSU) and West Virginia University (WVU) in association with the MRIs of the Massachusetts Institute of Technology (MIT) and the University of Minnesota (UMN). (FIGURE 34) Michigan Technological University (MTU) is also affiliated with the Center in the area of diesel particulates.The Center brings together experts concerned with particles causing potentially disabling or fatal diseases including pneumoconiosis (""black-lung""), silicosis, and asbestosis. The latter is of deep concern not just to workers in the mineral sector of the economy but also to the general populace. The primary goal of the Center is to reduce the incidence and severity of respirable dust disease through advancing fundamental understanding of all aspects of respirable dust associated with mining and milling, and the interaction of dust and lungs. The research program of the Generic Mineral Technology Center explores these scientific, engineering or medical concerns with the objective of refining existing strategies and developing new respirable dust control techniquesand technology that are consistent with the fundamental dust-lung interaction processes that lead to mine worker disability. The work concentrates on five areas (FIGURE 35):"

Nov 1, 1988

By Diego Berti Salvaro

A morfologia, dimensões e composição química de tribocamadas são fortemente dependentes das pressões e temperaturas existentes no contato e oriundas das reações das superfícies entre si, com a atmosfera, com os lubrificantes e contaminantes presentes no contato. No presente artigo foi analisada a formação de tribocamadas em pares DLCaço inoxidável testados por 180, 500, 1000 e 2500 horas em atmosfera de gás refrigerante R134a sem a presença de óleo lubrificante. A caracterização foi realizada por microscopia eletrônica de varredura espectroscopia de energia dispersiva (MEV-EDS) (morfologia e composição química) e interferometria ótica de luz branca (dimensões). Nas análises por MEV-EDS foram identificadas tribocamadas que se apresentaram mais pronunciadas nas superfícies do aço inoxidável sendo as mesmas oriundas de transferências mútuas entre os pares tribológicos bem como oxidação. A espessura das tribocamadas, por sua vez variou de 100 a 500 nm. Os resultados revelam que as tribocamadas são quimicamente estáveis e que suas espessuras não variam significativamente após mil horas de ensaio.

Aug 16, 2017

By J. P. Sims

Abstract - Ultramafic to mafic igneous intrusions of the Las Aguilas district form part of a belt of generally mafic plutonic bodies within medium- and high-grade early Paleozoic metamorphic rocks in the southern Sierras Pampeanas region, Province of San Luis. The intrusions host the largest known nickel sulfide resource in Argentina and contain significant Cu, Co and PGE mineralization (2.2 Mt at 0.5% Ni, 0.5% Cu, 0.035% Co). Sulfides at Las Aguilas Este, one of two principal mineralized zones, are hosted by a body comprising subvertically dipping units of predominantly orthopyroxenite and melanorite cumulate, with lesser dunite, harzburgite, norite, leuconorite, and amphibolite. The units are zoned horizontally from ultramafic to mafic compositions, representing primary magmatic zonation away from an original base or side of the intrusion. Intercumulus nettextured and disseminated aggregates of pyrrhotite-chalcopyrite-pentlandite are concentrated in the peridotitic zones and extend into melanorite. Whole rock major and trace element compositions, and olivine chemistry, indicate that the parent magma was gabbroic/basaltic with 100 (Mg/Mg+Fe) near 59, and resembles tholeiitic magmas generated in subduction-related arc, or back-arc settings. Unusually aluminous Cr-bearing spinel is compositionally similar to those in some synorogenic mafic/ultramafic plutons in magmatic arc settings. Relatively Ni-depleted olivines and low Cu/Pd ratios are indicative of magmatic sulfide segregation early in the crystallization of the magma. Early orthopyroxene saturation and virtual lack of clinopyroxene, in conjunction with sulfur isotope values up to +6.6 ‰, spinel compositions, and presence of graphite, phlogopite and magmatic hornblende, all attest to probable crustal contamination of the parent magma. Assimilation of crustal sulfur may have been crucial in the early attainment of sulfide saturation and resultant formation of magmatic Ni-Cu sulfide mineralization. Fabrics, textures and mineralogy of the intrusions and country rocks and U-Pb zircon dating indicate syntectonic-synmetamorphic emplacement at 478±6 Ma during the Famatinian (Ordovician) orogeny. Minor to locally significant recrystallization and deformation of mafic-ultramafic rocks and redistribution of sulfides and PGE occurred during and following the Famatinian orogeny. The Las Aguilas intrusion is one of several tholeiitic mafic-ultramafic intrusive complexes within an Ordovician arc - back-arc system in the Sierras Pampeanas. Aeromagnetic datasets and regional mapping suggest there is further potential for intrusion-hosted Ni-Cu mineralization along this eroded magmatic arc.

Jan 1, 1999