Search Documents

By B. Barry, M. S. Klima

"Testing was conducted to evaluate the effects of hydroacoustic cavitation (HAC) treatment on two bituminous coal slurries and the subsequent separation of each slurry in a classifying hydrocyclone. HAC treatment was performed using a pilot-scale circuit fabricated by Furness-Newburge Inc. The circuit was designed to induce cavitation by means of flow through an ultrasonic resonator chamber or enhanced cavitation by initial flow through a cavitation chamber followed by flow through the ultrasonic chamber. The test materials were nominal -1,500-micron and -150-micron Illinois-basin bituminous coal slurries, which were obtained from an operating coal preparation facility. After 5 sec of HAC treatment, the median size of the -1,500-micron material was reduced, with ash values for certain size fractions decreasing more than 5 percent compared with untreated samples. Extending treatment time led to greater degradation of the +1,180-micron material and an increase in the -25-micron material, with ash reductions occurring for material in the -850+150-micron size range. Size degradation was less for the -150-micron material. Subsequent separation of the treated slurries was carried out in a hydrocyclone with diameter of 102 mm. HAC treatment led to a decrease in the ash value and an increase in the heating value of the underflow stream compared with the feed material. For example, the ash value was reduced by about 16 percent for the -1,500-micron material and 25 percent for the -150-micron material with heating value increases of 7 and 33 percent, respectively, after HAC treatment. Overall, HAC treatment appeared to have a slight effect on the size selectivity curves.IntroductionUltrasound in the range of 20 to 1,000 kHz, referred to as power ultrasound, consists of high energy waves that can create zones of compression and expansion when used to irradiate liquids (Frederick, 1965; Leighton, 1994; Mason and Lorimer, 1988). This action generates varying pressure regions leading to cavitation or the formation, growth and near-immediate collapse of microscopic voids or bubbles (Frederick 1965; Leighton 1994; Mason and Lorimer 1988). Collapse occurs when the bubble reaches critical size and cannot absorb additional sound field energy, and the critical size is governed by the ultrasound frequency (Shchukin et al., 2011)."

Jan 1, 2015

By Xiaoxing Hu, Guibing Zheng, Yangge Zhu, Xingrong Zhang

"In China, more than 90 percent of titanium resources are reserved in vanadic titano-magnetite deposits. In this type of ore, the same elements such as Ti, Fe, Ca, Mg exist on surface of both ilmenite and titanaugite (the gangue mineral) because of isomorphism, which makes selective flotation difficult. Therefore, how to enlarge the floatability difference between these two minerals has always been a research emphasis and still needs to be studied further. In this paper, the pre-treatment methods using ultrasonic wave were proposed. The results indicate that ultrasonic treatment shows beneficial effect to enlarge the floatability difference, and the effect will be strengthened by extending the ultrasonic treatment time or increasing the ultrasonic power. The mechanism was investigated through infrared spectroscopic (FT-IR) analysis. Collector interacts with Ca and Mg which results in titanaugite flotation, after ultrasonic treatment, the dissolution of Ca and Mg is intensified, which leads to the lack of active points on mineral surface, so the floatability of titanaugite is depressed. Meanwhile, collector mainly interacts with Fe which results in ilmenite flotation, and the present of ultrasonic might promote its oxidation (Fe2+ to Fe3+), so the floatability of ilmenite after sonication is increased.INTRODUCTIONUltrasonic is the sound wave with frequency of 2 × 10-4 Hz~2 × 10-9Hz. Since the first International Symposium of Sonochemistry in 1986, the application of ultrasonic wave is more and more extensive. In researches about mining and metallurgy, various investigators have shown that intensive acoustic fields can modify the state of a mineral, leading to chemical or dispersive effects. Generally, the effect of ultrasonic vibration depends upon the nature of the mineral and also the way ultrasonic wave is applied (Celik, 1989; Ozkan, 2002). In addition, ultrasonic treatment usually plays roles of removal of reagents adsorbed layer from minerals and emulsification of flotation reagents when it is used in flotation (Nicol, Engel, & Teh, 1986; Slaczka, 1987; Djendova & Mehandj, 1992; Farmer, Collings, & Jameson, 2000; Gurpinar, Sonmez, & Bozkurt, 2004)."

Jan 1, 2016

By Nobuaki Sato

The electrical conductivity, k, of pure and sodium doped sulfur melts was measured with and without ultrasonic waves at temperatures ranging from 140 to 340'C by the two probe method using an ultra high resistance meter. The k value of the pure sulfur melt with irradiation jumped at around 170°C by an order of 102 after which it mouutuniocally increased from 10-5 to10-4 A' 1 cm-1 with an increase of the temperature. The addition of the sodium metal to the sulfur melt was found to cause a larger jumping in the K value. The k value increased with the increase of Na proportion in the melt. For a 10mol% Na doped sulfur melt it was as high as max ~30 A 1cm -1 above 180 C under the irradiation of of ultrasconics.

Jan 1, 2003

By Nobuaki Sato

The electrical conductivity, k, of pure and sodium doped sulfur melts was measured with and without ultrasonic waves at temperatures ranging from 140 to 340° C by the two probe method using an ultra high resistance meter. The II: value of the pure sulfur melt with irradiation jumped at around 170°C by an order of 102 after which it monotonically increased from 10-5 to 10-4 (omega) 1cm-4 with an increase of the temperature. The addition of the sodium metal to the sulfur melt was found to cause a larger jumping in the II: value. The II: value increased with the increase of Na proportion in the melt. For a 10 mol% Na doped sulfur melt it was as high as max. ~30 (omega) 1cm-1 above 180°C under the irradiation of ultrasonics.

Jan 1, 2003

By B. Orberger

The fine fraction (< 2 mm) of the high grade Mn-ore from the world class Moanda deposit, Francevillan basin, in Gabon, contains up to 30 wt. % of manganese and about 0.4 wt. % phosphorous. A pilot study at laboratory scale integrating mineralogy and geochemistry before and after ultrasonic treatment was conducted on the fine fraction (< 2 mm) of oxidized Mn ore in order to reduce the phosphorous content and enrich this fraction in manganese. The fine fraction was dried, crushed at 2 cm and sieved at 2 mm. The two fractions (< 2 mm and 2 mm ? 2 cm) were investigated by X-ray diffraction and scanning electron microprobe ? electron dispersive spectroscopy analyses. Both fractions contain lithiophorite, cryptomelane and pyrolusite as Mn carrier, and goethite, muscovite, illite and quartz as contaminants. The Mn hydroxide nsutite was only found in the fraction 2mm ? 2 cm.The < 2 mm fraction is significantly richer in goethite, muscovite/illite, and quartz. Phosphorous carriers are mainly goethite (up to 2.8 wt. % P2O5), while the Mn minerals contain up to 0.8 wt. % P2O5. The Mn minerals are partly included in an agglomerate of goethite, muscovite/illite, and quartz. The < 2 mm fraction was treated by ultrasound for 30 s in normal water. Mineralogical and chemical analyses after ultrasound treatment showed that the Mn-minerals were largely liberated from the goethite-muscovite-illite agglomerate. Mass balance calculations show that after ultrasonic treatment the < 2 mm fraction was ? 50 % enriched in Mn and ?50 % impoverished in P.

Sep 1, 2012

By R. D. Schmidt, M. J. Friedel

Unsaturated permeability and flow capacity exist where copper mineralization is disseminated in segmented, very-low-permeability ore blocks. The US Bureau of Mines (USBM) investigated this condition for application to in situ, copper-leach mining at the Cyprus Casa Grande mine site. Moisture retention properties are derived and combined with scanning-electron-microprobe data to characterize the host rock&apos;s mineralogy, texture, pore size, distribution and permeability. Finite element modeling is used to estimate saturated permeability and the ambient degree of saturation and to gain insight into appropriate in situ leach design. Recommended design modifications for optimized solution distribution and maximum recovery from the Casa Grande ore require: • well pressure injection exceeding 1500 psi and recovery wells operating in a suction mode, or • secondary, permeability enhancement by explosive rubblization. In the former, the lack of conditioning and the use of lesser pressures will result in leach solutions confined to the macrofractures. With the latter requirement, pressures can be reduced to 500 psi, with improved recovery and solutions containment.

Jan 1, 1993

By F. Göktepe

Flotation gases and conditioning of the pulp with them are one of the important parameters of flotation and should be taken into account especially in the flotation of sulphide ores. In this study, flotation of pure chalcopyrite and pyrite samples were investigated with air, oxygen and nitrogen as flotation gas and the effect of conditioning with these three gases also were performed. Flotation gas was introduced for 5min, 10min, 15min and 20 min. For chalcopyrite flotation there was no drastic change in recovery when air, oxygen and nitrogen were used as flotation gas but conditioning the pulp with oxygen for 10 minutes increased the recovery about 8% where pulp potential has been approximately 25 mV with chalcopyrite and 150 mV with platinum electrodes. Conditioning with all three gases decreased the pyrite recovery by about 20% with 20 minutes conditioning. Pulp potential decreased in the presence of nitrogen while conditioning with air and oxygen increased the pulp potential for both electrodes. Generally potential increased for both minerals with oxygenation and aeration time but it was stable or slightly decreased with nitrogenation. Comparison of the gases showed that the different flotation gases do not effect flotation recovery but conditioning the pulp with these gases at pre-flotation effects chalcopyrite and pyrite flotation recovery, most dramatically pyrite.

Jan 1, 2014

By K. C. Corin, Z. G. Song, J. G. Wiese

In the present investigation flotation was used as a diagnostic to understand the effects of changes to the media during the grinding stage. The observations from flotation for different media are discussed in terms of particle size distribution, water recovery, solid recovery and valuable mineral recovery. The chemical parameters; pH, redox potential (Eh) and dissolved oxygen (DO) levels were measured. A Base Metal Sulphide (BMS) ore was ground under media of different shapes and compositions to determine the effect of different rod/ball material on the flotation performance of the ore. For a given grind (D80 = 75 µm), media shape had no effect on flotation performance of a BMS ore. Different grinding media had significant effect on slurry chemical properties and flotation performance. Mild steel rods (RMMS) produced the highest solids recovery, nickel and pyrrhotite (Po) recovery, with the highest ethylenediaminetetraacetic acid (EDTA) extractable iron and the lowest DO level. Chrome steel balls and stainless steel rods produced the lowest metal recovery, EDTA extractable iron and the highest DO level. A complementary study was conducted to investigate the effect of using different grinding media compositions, viz, ceramic, forged steel, 15% chrome steel, stainless steel and a mixture of stainless steel and 15% chrome steel (50:50) balls were investigated using a Platinum Group Mineral (PGM), UG2 ore. Grinding products of five different media produced the same solids and water recovery, but the grades and recoveries of Platinum Group Elements (PGE) and chromite were different. Grinding products of ceramic media showed the best flotation performance, with the highest PGE recovery and the lowest Cr2O3 recovery. While grinding products of stainless steel balls (SS) produced the lowest PGE recovery and highest Cr2O3 grade and recovery in the concentrates.

Jan 1, 2016

By K. C. Corin, Z. G. Song, J. G. Wiese

In the present study the effect of using different grinding media, viz, ceramic balls, forged steel balls, 15% Cr steel balls, stainless steel and mixture of stainless steel and 15% Cr steel balls (50:50) on the flotation performance of a Platinum Group Mineral (PGM) UG2 ore was investigated. Test work was conducted using a laboratory scale horizontal tumbling mill and a batch flotation cell. Power draw to achieve a specific P80 was determined for each media type. Changes in flotation behaviour were evaluated in terms of particle size distribution, water recovery, solid recovery and valuable mineral recovery. pH, Eh and DO levels were also measured. Grinding products of five different media produced similar solids and water recovery, which is indicative of the froth characteristics, but the grades and recoveries of PGE and chromite were different. The product obtained when using ceramic media showed the best flotation performance, producing the highest PGE recovery and the lowest Cr2O3 recovery. The products obtained when using stainless steel balls (SS) produced the lowest PGE recovery and highest Cr2O3 grade and recovery. The paper proposes possible reasons to explain these observations which may have significant importance for the operation of a PGM concentrator.

Jan 1, 2015

Toxic gases, mostly carbon monoxide (CO) and nitrous oxides (NOx), are invariably generated by commercial explosives under practical conditions of usage because of oxygen unbalance and non-ideal chemical reaction. Permitted explosives are statutorily required to meet the criteria stipulated by regulatory authority for their toxic fume quality for their safe use in underground coalmines. Solid blasting using P5 explosives contribute around 60% production from Indian underground coal mines. Low pull and yield per blast in solid blasting has been identified as a reason for low production and productivity of Indian underground coal mines. In an effort to improve performance of solid blasting, it was envisaged to apply air decking between suitable P5 explosives using high density polyethylene (HDPE) spacers under a Ministry of Coal, Government of India funded project. A non-deflagrating slurry explosive composition having high air gap sensitivity was specially developed for this purpose, so that air decked cartridges get detonated sympathetically with single priming. However, statutory authority in India apprehended that the use of oxygen negative HDPE spacers can influence the generation of toxic gases. The effect of using HDPE spacers on the generation of toxic gases was studied under simulated laboratory conditions with newly developed as well as with three commercial P5 explosives. The results of studies presented in this paper revealed that the level of carbon monoxide increases linearly and there is no significant effect on the level of oxides of nitrogen due to the use of HDPE spacers with selected explosives. Studies also revealed that this newly developed slurry explosive can be used for air decking up to 15 cm using HDPE spacers of weight not more than 21 g without exceeding the permissible limits for toxic gases.

Jan 1, 2008

By A. B. Kinzel

ALTHOUGH vanadium is an important constituent of almost every brand of high-speed steel manufactured today, little is known as to its role in this series of alloys. The now standard 18 per cent tungsten and 4 per cent chromium constituents were the result of developments and improvements before 1903. In that year, vanadium was added to the steel by Dr. J. A. Mathews. This proved to be an outstanding con-tribution, so that the standard high-speed steel of today is generally referred to as the 18-4-1 type-18 per cent W, 4 per cent Cr and 1 per cent V. Various modifications have been attempted, since then, but with the exception of the introduction of cobalt, no striking improvements have occurred. Vanadium has been increased to 2 per cent in many of the common brands, and at least one brand contains 5 per cent V in addition to the usual tungsten and chromium. The carbon has been gradually increased so that it is not uncommon to find 0.80 per cent in the standard grade, although the carbon in the 5 per cent vanadium steel mentioned above is approximately 1 per cent, and even 1.2 per cent has been made experimentally. The role of vanadium has never been well understood, and although vanadium has been increased to 2.5 and even 5 per cent in certain high speed steels, it has not been generally established that the higher vanadium contents &apos;result in superior cutting properties. However, in all of the investigations, of which the writers are aware, the interrelation of the vanadium and carbon contents was not considered as a prime factor. The carbon content was held at 1.2 per cent or less-generally at the usual 0.65 to 0.75 per cent.

Jan 1, 1932

By Yang Xiao, Zhang Yimin, Bao Shenxu, Liu Chun

Stone coal is a unique vanadium-bearing resource in China. Many techniques, such as salt roasting-water leaching, blank roasting-acid leaching, direct acid leaching etc. have been developed for vanadium extraction from stone coal. The vanadium leaching rate can reach 74.9% for stone coal from Jiangxi, but only about 27% of vanadium is leached for Hubei ore by applying salt roasting-water leaching technique. This paper investigats the vanadium occurrence in stone coal by microscope observation and electron probe, and compares the minerals components of stone coal from Jiangxi and Hubei. Although most vanadium exist as an isomorphism by replacing Al(III) from dioctahedral structure in mica group minerals in stone coal from two regions, the free vanadium is remarkably abundant in Jiangxi stone coal than in Hubei stone coal, which results the fact that vandium is relatively readily extracted from former. Moreover, the content of calcite in Hubei stone coal is much higher than that in Jiangxi stone coal. Calcium can react with V2O5 to form water insoluble calcium vanadates during roasting and this may be the reasone why the water leaching rate of vanadium is low for Hubei ore. Acid leaching is more beneficial to the vanadium leaching but other extra methods, such as adding aid-leaching agent and/or increasing acid concentration is need for the ore where vanadium is embeded firmly. This study can effectively guide the selection of vanadium extraction techniques for stone coal from different regions.

Jan 1, 2014

At times the phosphate industry, in Florida, encounters phosphate rock that gives lower than expected P2O5 recovery in the rougher plant section. The drop in recovery is typically 10% and as much as 30% or more. Variations in feed quality from day to day, shift to shift and even from drag-line to drag line, represent a challenge to the beneficiation plant operators and reagents? suppliers. Therefore, this characterization study has been initiated to identify the reasons for the differences in flotation behavior of such feeds. The study involves many samples to cover such variations. The characterization work includes: ? Mineralogical and chemical analysis; ? Size, shape, surface roughness and porosity analysis; ? Surface charge and surface contamination with other phases (minerals); ? Clay content and its relationship to phosphate and silica particles. The results correlated with flotation data and adsorption density measurements clearly establish the statistically significant variability in characteristic features that influence flotation response. This article discusses results from the above listed studies. On the basis of the obtained data, recommendations of practical approaches to overcome the problem of feed variability in phosphate flotation plants are delineated.

Jan 1, 2014

By James K. Stanley

WHEN a plastically deformed metal is heated to a certain temperature, it undergoes a complete change in microstructure, the consequence of which is a marked alteration of mechanical properties such as hardness, strength and ductility. This change in microstructure occurs by recrystallization and is a process involving the formation and growth of strain-free nuclei in the deformed matrix. These nuclei continue to form with time and grow until a new grain structure replaces the cold-worked structure. The formation of the nuclei in the deformed sheet of 1 per cent silicon ferrite is illustrated in Fig. 1. If a recrystallization is conducted isothermally, a measurement of the fraction of the matrix recrystallized plotted against time leads to an isothermal recrystallization curve, first established in 1942.1 Such recrystallization curves are shown in Fig. 4. These curves show that the recrystallization of a cold-worked metal is best considered as a rate process rather than a time independent process such as is suggested by the improperly named and misleading recrystallization diagrams involving deformation, temperature, and grain size. 2-5 Any study of the rate of recrystallization resolves itself into a study of the component rates of nucleation and growth. The previous paper&apos; provided an account of the determination of the rates of nucleation; N, the number of nuclei formed per unit time per unit of unrecrystallized area, and growth, G, the radial growth in unit time, in the recrystallization of silicon ferrite (1 per cent Si). A method was developed to furnish experimental data for evaluating the effect of the recrystallization variables on N and G. The mathematical analysis for the derivation of the isothermal recrystallization curve was developed for a two-dimensional case (in thin sheets where the diameter of the recrystallized grain is greater than the sheet thickness). The present paper is a continuation of the study of recrystallization of 1 per cent silicon ferrite begun in 1942.1 In this work the effect of the factors deformation, temperature, grain size, composition, and recovery is studied with respect to the rates of nucleation and growth. At the same time it is shown how the cooperation of N and G affects the isothermal recrystallization curve. The study of these variables on N and G has a definite bearing on the mechanism of recrystallization and should lay a foundation for a rational theory on the subject. PROCEDURE The procedure used in these experiments was essentially the same as that described previously but in certain details some changes were made in the interests of speed. With few exceptions, the procedure is the same for the study of all the variables. Where the procedure is different from standard manipulations attention is called to this fact.

Jan 1, 1945

By Rajive Ganguli

A control algorithm was developed previously for loading coal trains such that each car met customer specifications (Ganguli, 2001). In developing the algorithm, the effect of the variance of coal was not investigated. This paper explores the effect of the variability of coal on the algorithm using two approaches: theoretical analysis and simulation. Both approaches demonstrate that variance is not an issue when the customer quality specification is close to the mine average quality. However, when they are far apart, the performance of the algorithm improves with variance.

Jan 1, 2002

By A. Mitrašinovic, A. Wolf

"The aim of this investigation was to determine the most suitable additive for recovering metals from converter slags generated during Ni extraction. Fluxes analyzed were silica and lime and reductants included pig iron, ferrosilicon and copper-silicon compound. Slag was settled at 1300°C for one hour to simulate the smelting environment. The newly formed matte and slag were characterized by chemical composition and morphology. Microstructural studies showed that slag formed after adding reductants consisted of primarily fayalite, with traces of magnetite. Entrained matte was present in the slag mostly as prills of Ni3S2-FeS matrix and a Cu2S-FeS secondary phase below 10µm in diameter. Kinetic parameters of matte formation, valuable metal recovery rates and partition coefficients were deduced. Silica additions generated higher partition coefficients for copper and nickel than the addition of lime. Additives used as reducing agents had higher valuable metal recovery rates and partition coefficients. Silica additions favoured the formation a higher grade matte while lime additions will hinder metal recovery. Pig iron, ferrosilicon and Cu30Si were the most effective reductants for valuable metals recovery. Cu10Si and coke additions had little to no effect on valuable metals recovery."

Jan 1, 2015

By I. Milton LeBaron

OPERATION of the phosphate flotation plant at the Peace Valley mine of the International Minerals and Chemical Corporation, Florida, began in the summer of [ ] 1942. Since that time several changes have been made in the flowsheet, with resultant increases in metallurgical results. Three flowsheets, together with the comparative plant results, are given in this paper, together with a discussion of the desliming circuit used for preliminary washing of the flotation feed. FIRST FLOWSHEET CHANGES Fig. I lists the essential units in the original flowsheet at the Peace Valley plant. The figures for tonnage and grade are average for a period of two months. Mineral Separation Airflow cells are used for both the fatty acid and the amine float. Three immediate difficulties presented themselves in the use of this flow sheet: I. Floating a maximum amount of phosphate in the rougher section to give good recovery sent a low-grade concentrate to the silica float, resulting in high costs for amine reagent in that section.

Jan 1, 1946

By G. Sachs, E. J. Ripling, J. J. Lynch

INTRODUCTION General IT is general practice to evaluate the strength properties of a particular metal from its stress-strain [(S1 - E1]) curve obtained by means of a conventional tension test. Such a stress-strain curve, Fig I, illustrates two important properties of a metal, its ability to strain harden, and its ability to withstand a certain limiting stress, the "fracture stress,"[ (s&apos;r)], and a certain limiting strain, the "ductility" [(e1)], before it fails by separation. These two fracturing characteristics are the coordinates of the point of fracture in Fig I. In the case of a metal which necks in a tension test, both the fracture stress and the ductility (measured in a tension test) are dependent upon (a) the shape of the neck and (b) average values of the stresses and strains over the cross section at the moment of fracture. However, for the purpose of this investigation, these average quantities, rather than the actual values, may be considered for reasons of simplicity. It appears that the conclusions also hold true if the analysis were carried out for actual values of fracture stress and ductility at the locus of failure. In this paper, the effects of straining (at room temperature) by various methods on [ ] the above metal characteristics, which were determined by subsequent tension tests will be discussed. According to our present knowledge, any such prestraining results in a stress-strain curve (in subsequent testing by tension), Fig 2, the general shape, or flow characteristics, of which can be derived from the original stress-strain curve of the unstrained metal minus a certain portion exhausted by the initial straining. This phenomenon is called strain hardening, and may be measured by the magnitude of the cut-off, or the "effective strain," from which the new curve must start in order to coincide in its plastic branch with the original stress-strain curve.

Jan 1, 1948

By M. A. Reyes, J. Bickson, J. R. Srednicki

Federal laws mandate the presence of refuge alternatives (RAs) in underground coal mines and provide guidelines for harmful gas removal. After an explosion, harmful gases can follow survivors into an RA and can reach a deadly concentration. Investigators from the National Institute for Occupational Safety and Health (NIOSH) tested 12 ventilation system configurations (VSCs) to purge sulfur hexafluoride (SF6) tracer gas from a built-in-place (BIP) RA in the Experimental Mine in Bruceton, PA. Using a borehole air supply, tests were conducted with airflows of 750 and 1,000 standard cubic feet per minute (SCFM). Excluding a VSC where the air inlet was 1.98 m (78 in) from the air outlet, the results show that the time to purge the SF6 concentration from 1,000 parts per million (ppm) to 25 ppm ranged from 26 to 29 minutes for an airflow of 750 SCFM and ranged from 18 to 23 minutes for an airflow 1,000 SCFM. Mines can use this information to reduce purge time in case of a mine disaster and determine which VSC to avoid. INTRODUCTION After a fire or an explosion in an underground mine, the concentration of carbon monoxide can reach a fatal level. In a mine disaster, the main goal is to escape. However, if miners cannot escape, they have to migrate to a location to find refuge and, if possible, communication, and a borehole source for a fresh air supply. To ensure survival of the miners, Federal laws mandate the presence of a refuge alternative (RA) within 304.5 m (1,000 ft) of the nearest mining face. In addition, Code of Federal Regulations Title 30 CFR Section 7 sets the guidelines for personnel tracking, RAs, and the removal of noxious gases in underground coal mines (Mineral Resources, 30 CFR, 2014). Federal regulations define an RA as a protected, secure space with an isolated atmosphere and integrated components (Mineral Resources, 30 CFR, 2014). There are three types of RAs: portable metal RAs, portable tent-type RAs, and built-in-place (BIP) RAs. A BIP RA is constructed using masonry or other stoppings to create an isolated space in a mined-out area. Blast doors are installed in one or both of the stoppings for the miners to enter the RA. Furthermore, RAs must provide the following components: breathable air, food, water, air monitoring, and harmful gas removal. Federal regulations have emphasized the mandate for breathable air and harmful gas removal in the following words: “Purging or other effective procedures shall be provided for the airlock to dilute the carbon monoxide concentration to 25 ppm” (Mineral Resources, 30 CFR, 2014). The purpose of the mine ventilation system is to provide a sufficient quantity of air to the underground mine workings, to dilute methane and other contaminants, to maintain a suitable working environment, and to prevent accidents from happening (Cheng and Wei, 2014). In addition, the organic nature of coal amplifies risks from poisonous gases, explosions, and fires (Engström et al., 2018). If an underground coal mine ventilation system fails after an explosion, the concentration of toxic gases, most notably carbon monoxide, will increase. Carbon monoxide is dangerous because it creates tissue hypoxia by binding to hemoglobin (Özmen and Aksoy, 2015).

Jan 1, 2019

By Li Yang, Andre Cezar Zingano, Alberto Fronza

"Immediate roof control is very important to the security and stability of entries in coal mining. It is also the highest cost in the coal mining operation, and roof spalling is directly responsible for coal contamination. The immediate roof in the coal mines in the State of Santa Catarina varies in lithology and in the presence of structures, such as bedding planes, vertical fractures that cut lamination, sandstone, and siltstone boulders. The presence and crossing of these structures should influence the decision of the specification of the roof support. Furthermore, the variation of rock layer and quality of the roof must be immediately followed by the variation of support specification. This work aims to study the behavior of the immediate roof under different geological and structural conditions during the excavation of entries, including the changing of the geometry of the entry as a function of time. This includes the effect of vertical fractures that cross the bedding planes of the roof and the position of those fractures on the roof. The effect of time between excavation and installing support to stabilize the roof is also examined. This study uses empirical methodologies for support design and numerical methods to study the behavior of the roof when anchored to the different scenarios proposed. The results of this work show the importance of quality characterization of the roof in terms of the type of rock and its thickness and the presence of vertical fractures that cut the bedding planes of the roof immediately.INTRODUCTION The immediate roof in a coal mine can varies in terms of typology and structural features, like bedding plane spacing and vertical joints. The roof support must be specified based on the features of the roof layer and its classification. Unal (1983) and Mark, Molinda, and Dolinar (2001) suggest that the roof support design should be based on the rock mass rating (RMR) and coal mining roof rating (CMRR), which look at rock mass classifications. These methods are based on the beam-building approach, and the bedding planes are tied together using fully grouted bolt. The bolt can be pre-tensioned or not depending the time of the curing of the resin."

Jan 1, 2017