Search Documents

Laboratory experiments show that the delay detonators, either electric (copper coated or aluminium) or non-electric (down-the-hole) as generally used in opencast mines and quarries have some scattering from the actual firing time due to manufacturing inaccuracy and variations in basic ingredients of the product. This scattering varies from 1 to 4 % depending on the product quality. Due to this component scatter, adverse blasting effects like misfires, overbreak, underbreak or fly-rock may occur if the design patterns are not judiciously made. It has also direct impact on muck profile and fragmentation.

Jan 1, 1999

By N Gkikizas-Lampropoulis

Selection of delay times to optimize fragmentation has been a controversial topic among researchers and blasting practitioners. This paper interprets previous experimental information on the effect of delay on fragmentation with the aid of some new experimental observations of the time of detachment of the free face of the blast as well as results of numerical modelling. It was shown that detachment of the burden occurs at delays shorter than the one which produced optimum fragmentation in the experiments, suggesting some fragmentation improvement due to gas action. In addition, at the spacing to burden ratio of the experiments, the damage zone from an earlier detonating charge extends the distance to the neighboring charge, essentially affecting the burden of some of the holes of the blast, at detonation time. Computer modelling demonstrated that increased spacing results is less overlap of stress induced damage zones meaning that there is less influence of delay on stress wave induced fragmentation. It was also shown that simultaneous initiation results in less back break, while increased back break may result even with short delay times.

Jan 1, 2016

By Martin F. Milligan

THIS short discussion of the effects of deoxidation on the mechanical properties of cast steels is intended to serve as general introduction to the subject of this afternoon's session. The subject is covered in detail in Mr. Carter's excellent paper. My material has been collected from the works of various investigators, several of whom are present today. For a definition of deoxidation, as applied to steel-furnace melting practice, we can best go to Briggs' book, "The Metallurgy of Steel Castings." Briggs says that deoxidation "includes all the phenomena in the final preparation of steel that would permit it to solidify free from gas cavities and from dissolved oxygen of all kinds." Various practices are used by welters to produce these end results.

Jan 1, 1947

By Chen Zhang

Polycrystalline Ti-rich NiTi thin films have been deposited from a single NiTi target using a DC magnetron sputtering system. Free standing film was obtained by using a single crystal silicon substrate. Thickness ofthe thin films is controlled at around 12 pm. In this investigation, the effect of deposition temperature on the microstructure and transformation temperatures of the thin films is studied. Influence of post heat treatment temperatures on the properties of the thin films is also investigated. Transformation temperatures of the thin films are determined by differential scanning calorimetry (DSC). The surface microstructure of the thin films is studied using a scanning electron microscope (SEM), and the crystallinity is determined using x-ray diffractometry. It is found that the thin film deposited on a hot substrate is crystalline even when the substrate temperature is as low as 300°C, while the normal crystallization temperature for an amorphous thin film is around 500°C. The microstructure of the film deposited on a hot substrate shows a very fine grain size. The grain size increases with increasing substrate temperature during deposition. The effect of post deposition heat treatment on grain size is minimal.

Jan 1, 1999

By A. M. Marabini, G. Belardi, V. Alesse, E. Spaziani

The objective of this investigation was to verify the effectiveness of commercial and synthetic depressing agents in a complex oxidized zinc mineral flotation flowsheet using sodium sulfides and amine. The flotation tests were run on a finely-disseminated calamine ore grading 16.96% Zn and containing smithsonite, hemimorphite, cerussite, calcite, quartz and iron oxide, present essentially in colloidal form. The reagents used in the testing can be grouped into four classes: guar, starch, celluloses and acrylic polymers having various degrees of substitution and molecular weights. The depressants exhibiting the greatest selectivity towards the gangue (considered as a whole) are tripolyphosphate, polycarboxylic acids, methylcarboxylate guars and ethyl hydroxylic starch. In the rougher stage, the Zn recovery ranged from 70% to 80%, and the Zn grade ranged from 27% to 29%. In the Zn-Fe2O3 separation, the compounds ensuring the most efficient separation are the tripolyphosphate and the polycarboxylic acids. In the Zn-SiO2 separation, the compounds that exhibit the best separation efficiency are tripolyphosphate and guar of methylcarboxylic sodium salt. In the case of the Zn-Ca separation, methyl-carboxylic guar exerts the best depressing effect and does not adversely affect the Zn recovery. The separation provided by ethyl hydroxylic guar is also good, although not as good as the preceding reagent. Regarding the Zn-Al separation, the tripolyphosphate, the celluloses and the carboxylate guars are the best depressants. A hypothesis is advanced to interpret the depressing action of the most effective reagents.

Jan 1, 1995

By H. A. D. Kirsten

Mining-induced seismicity is usually evaluated in terms of continuum elastic analyses, and is quantified in terms of energy release rate as state parameter and excess shear stress along particular features on which failure may be induced. Although both of these quantities are representative measures of potential seismic activity, elastic analyses do not enable the associated stresses and displacements in the rock in which failure occurs to be evaluated reliably. The paper compares the effect of depth, span, support stf1Jhess, field stress ratio, and discontinuity strength on mining induced seismicity determined from elastic analyses and from analyses in which discontinuities in the rock are allowed to fall. It is, accordingly, shown that the incidence and magnitudes of potential seismic events and the net excess shear as representative state parameter cannot be determined reliably from elastic analyses that do not account for the failure of ubiquitous discontinuities. The magnitudes of seismic events in rock in which ubiquitous discontinuities are allowed to fail are very considerably overestimated in elastic analyses. The extent of the seismic source region and the associated seismicity do not increase with depth, which, together with the improved containment of the concomitant rockburst damage by backfill is reassuring for mining at greater depth in future. For conventional support, the magnitude of potential seismicity increases for an increase in span in elastic rock, but remains unaffected in non-elastic rock. For backfill, the magnitude of potential sesmicity decreases substantially in elastic and non-elastic rock for an increase in span. Increases infield stress ratio very significantly reduce potential seismicity irrespective if the type if analysis, but effect the distribution if potential seismic events very differently in elastic and non-elastic rock.

Jan 1, 1994

By G. C. Howell, H. A. D. Kirsten

The mining-induced effects around narrow tabular stopes have traditionally been evaluated in terms of elastic continuum analyses. An understanding of the phenomenological behaviour of the rock surrounding deep-level gold mines has accordingly been developed on the basis of such analyses. However, elastic analyses do not afford reliable representations of the behaviour of rock in which failure may occur on discontinuities. This paper describes investigations that show how the stress and stiffness characteristics of a rockmass are affected under such circumstances for representative ranges of values for the relevant parameters (depth, span, support stiffness, field stress ratio, and discontinuity strength). These investigations afford a substantially different understanding of the mechanical behaviour of rock that is subject to failure. Instead of forming an arch across the abutments, the rock in the hangingwall bears directly across the stope onto the footwall and, instead of being subjected to tension, the nether hangingwall is clamped in compression in the horizontal direction.

Jan 1, 1993

By M. Tang

The phosphate ore sample was taken from the iron tailings after recovering most of magnetite by magnetic separation in Longlin, Yunnan Province of China. Batch flotation tests had been conducted to upgrade the phosphate concentrate by conventional fatty acids reagents under 70% -75 µm of the particle size; however, the unsatisfied results (P2O5 grade of 27.84% and recovery of 49.25%) were obtained. Also there are a large amount of slimes trapped in the concentrate and high-dosages consumption of reagents, for example, more than15 kg/t soda ash and 2 kg/t sodium silicate at only one-staged roughing. Based on the analysis of X-ray diffraction (XRD) for the sample, most of gangues are clay, quartz, and chlorite, which may easy to over-grind and deteriorate the flotation process either on reagents consumption or slurry fluidity or viscosity. A hydro-cyclone had been introduced to pre-concentrate the phosphate ore by scrubbing the slime before flotation, which can result obviously in reducing the dosages of soda ash from 15 Kg/t to 4 Kg/t, and raising the grade of P2O5 in the concentrate from 27.84% to 36.13% at the expense of about 4% recovery of P2O5. They also substantially reduced the time of sedimentation of concentrate after flotation from ~10 to ~1 min. In this paper, the effects on the recovery of P2O5 by the different dosages of flotation reagents with or without de-sliming were studied, with the objective of determining the different effects on the functions of flotation reagents by slime during flotation. Keywords: de-sliming, phosphate, soda ash, flotation

Sep 1, 2012

By S Lukovic, Vishwa Bhushan, Calvin J. Konya

Effect of each of these variables has been well characterized for ANFO. This paper presents results of underwater energy measurements for one watergel and one emulsion type of slurry explosive which were initiated by 3 types of initiators (one electric and two cords of different strength) in 2 and 3 inch diameter steel pipes. Results of this 2 x 3 x 2 factorial experiment show the effects of detonating cord on energy released by the watergel and the emulsion explosive. Effect of diameter and its interaction with cord strength have also been characterized for the two explosives.

Jan 1, 1986

By C. Allen, M. Gangal, J. Stachulak

"Most underground diesel equipment is equipped with diesel oxidization catalysts (DOCs) to reduce carbon monoxide and hydrocarbon emissions. DOCs do not alter nitrogen oxides concentrations but can promote the oxidization of nitric oxide (NO) to the more toxic nitrogen dioxide (NO2). Vale and CanmetMINING have been researching how to reduce worker exposure to diesel emissions by testing mining equipment DOCs. Results indicate a > 77% decrease in carbon monoxide concentration but a 46–315% increase in NO2 concentration for 8-mode test cycles. It is recommended that DOCs that increase NO2 emissions be evaluated regarding their continued use in underground operations.RÉSUMÉ La plupart des équipements miniers souterrains sont équipés de catalyseurs d’oxydation diesel (DOC) afin de réduire les émissions de monoxyde de carbone et d’hydrocarbures. Les DOC ne modifient pas les concentrations des oxydes d’azote mais ils peuvent faciliter l’oxydation du monoxide d’azote (NO) en dioxyde d’azote (NO2), plus toxique. Vale et CanmetMINING effectuent des recherches pour réduire l’exposition des travailleurs aux émissions de diesel en analysant les DOC des équipements miniers. Selon les résultats, une diminution > 77 % dans la concentration de monoxyde de carbone est atteinte mais elle est accompagnée d’une augmentation de 46 à 315 % de la concentration en NO2 pour des cycles d’essais à 8 modes. Il est recommandé d’évaluer les DOC qui augmentent les émissions de NO2 pour décider de la poursuite de leur utilisation dans les opérations souterraines."

Jan 1, 2016

By D. Panias

Alumina hydroxides such as gibbsite (Al(OH)3) and boehmite (AlOOH) are precursors of many types of alumina that find important industrial applications. The thermal decomposition of AlOOH, which is a more energy saving precursor compared to gibbsite, gives rise to the formation of ?-, d-, ?- and a-aluminas that are used for the production of catalysts. The applications of the aluminas are governed by their properties that are a function of the precursor material and its microstructure. The microstructure in turn is a factor of the method and conditions applied, as well as, in the case of soft chemical processes, on the anions present. Towards these ends, this study was focused on the effect of different anions on the physicochemical characteristics of the alumina hydroxides precipitated in the first 5 minutes after the perturbation of the stability of a supersaturated sodium aluminate solution (Bayer liquor).

Jan 1, 2006

By Jiangwei Shen, Cong Wang, Haibin Zuo

The research on the formation of Silico-Ferrite of Calcium and Aluminium (SFCA) in the process of cooling and solidification is rarely reported. The crystallization process was observed by using scanning electron microscopy (SEM) and optical microscope in this paper. The effect of different cooling system on the microstructure and phase composition of the sinters was investigated to obtain the appropriate cooling rate to improve the metallurgical properties of sinters. The experimental results show that the crystallization of calcium ferrite is getting better when the cooling rate is decreased from water quenching to cooling in the air. There are a large number of hematite phases with interconnected crystal structure in the sample cooled in the air. In the case of the compressive strength, it was determined by the mineral composition and pore structure, higher SFCA and hematite contents in sinter cooling in the air lead to a higher strength. Glass phase in the water quenching sinter was the major reason for the lowest strength. High porosity contributes to a decrease in compressive strength for the sinter cooling in the furnace. Therefore the air cooling was the appropriate cooling rate to achieve high quality sinter under this experimental condition.

Jan 1, 2016

By Eugene P. Pfleider, Claus Freyberger

Generally, the different methods of financing new mining projects are not well understood by the engineers and supervisory personnel. Nor are the effects of these alternatives on depletion, taxes and profitability readily apparent to even the sophisticated management personnel without the aid of cash flow studies. Fortunately, with the advent of the computer it is possible now to simulate many different combinations of 1) equity, 2) loan and 3) production payment financing with little effort. A general computer program for cash flow analysis of mining ventures has been developed and applied as a case example to a 1967 feasibility study of the Underground Mining of Minnesota Taconite. The effects on profitability as measured both in rates-of-return and present value are presented for various financing combinations. In addition, percentage depletion rates were altered so as to measure the impact of this statuatory allowance. Based on the cost data as presented in the aforementioned 1967 feasibility study, and assuming 7% loans, the rates-of-return vary from 9. 9% to [00] % on equity variations and from 9. 9% to 11.4% on total invested funds.

Jan 1, 1969

By A. Abdollahi

Modification of the silicon in Al-Si alloys can be performed by adding a very small amount of some elements like Na, Sr and Ca to alter the form of silicon from an acicular shape to a fine fibrous one. This modification results in a considerable improvement in mechanical properties especially elongation, Metallographic observations in A356 alloy indicated the degree of the modification with Na, Sr and Ca, They showed that the effect of Ca as a modifier is not as strong as is Na or Sr while Na is the most effective modifier, Although modifiers improve mechanical properties, they also increase porosity in castings, The reduced pressure test (RPT) and Tatur test showed that the increasing porosity with Na is the most and with Sr is the least.

Jan 1, 2004

By R J. Singh, E. Z. Chacko, Devilal, S. K. Jha, Rina Sahu, Sheshank Shekhar

"Breakouts are one of the biggest problems encountered during continuous casting of steel billets. Billets get cracked locally or break completely in two parts during solidification causing the liquid part of the partially solidified billet to empty inside the cooling chamber. Proper control of important parameters is necessary to avoid break outs during continuous casting. In the present work, the nature of the break outs at a billet caster at Tata Steel was studied. Data analysis was also done for certain casting parameters and the Sulphur tracer test was conducted to understand solidification in the mould. It was found that to reduce the occurrence of break outs, it was necessary to tune the operations based on the grade being cast and the design of the mould tube being used.IntroductionA break out during the continuous casting process is a rupture of the partially solidified shell inside the secondary cooling chamber, causing the contained liquid steel to spill out. In the mid 1970s while continuous casting technology was still in early stage of development, causes of breakouts was not well understood. Today, with technological development much has been understood about breakouts but, most of the understanding has been in the slab casting process wherein due to the higher level of instrumentation, a lot of information has been gained. In billet casting however, due to the geometry of the mould housing with the tube mould, multiplied by the complexity of the multiple strands, instrumentation has not been used and obtaining data for analysis has been difficult.Breakouts at billet casters are still the main hindrances to production. A break out results in a loss in production since the strand which has had a break out is now not available to produce and thus a six strand caster would be reduced to a five strand caster, increasing the time for casting the same tonnage. Additionally extra set up time is required as more often than not a mould change is required in order to have the strand casting again."

Jan 1, 2014

By Ehsan Vahidi, Fereshteh Rashchi, Ataollah Babakhani, Alireza Zakeri

"The synergistic effect of Cyanex 302 on solvent extraction of nickel and cadmium from sulfate solution with D2EHPA diluted in kerosene was investigated with the aim of increasing separation efficiency. Experiments were carried out within a pH range of 0.1-5.0 using sole D2EHPA and D2EHPA-Cyanex 302 mixtures in different ratios. Increasing Cyanex 302 to D2EHPA ratios in the organic phase caused a left shifting of the extraction isotherm of cadmium and a right shifting of the extraction isotherm of nickel. As a result, optimum separation was found with a Cyanex 302 to D2EHPA ratio of 0.1M:0.5M. In the present system, effect of a modifying reagent such as TBP was studied. The influence of various diluents including kerosene and carbon tetrachloride was also investigated.IntroductionBatteries are popular sources of portable energy. Ni-Cd batteries are manufactured in two main groups of small domestic cells and large industrial batteries with 80% being in domestic use. Ni-Cd cells have various uses, for example in cordless electric utensils, cordless telephones, airplane engine starters, and communicational distribution systems [1].Depleted Ni-Cd batteries are classified as hazardous waste since nickel and cadmium are heavy metals and suspected carcinogens. Given the risk associated with uncontrolled disposal, directions for issuing legislation on disposal and recycling of used batteries have been made in industrialized countries [2]. Recycling of Ni-Cd batteries is important from both economic and environmental points of view. Different methods have been used for recycling these wastes through pyrometallurgy [3], biotechnology [4,5], and hydrometallurgy [1,2].Due to the advantages of hydrometallurgical processes, several studies have been implemented on leaching and solvent extraction (SX) of the used Ni-Cd batteries. Leaching of batteries is usually done in sulfate or chloride media; while solvent extraction has been used in different extractants: two-stage solvent extraction by D2EHPA and Cyanex 272 [6]. Solvent extraction of Cd from leach solutions has been studied using various extractants; Cyanex 301 [1], D2EHPA [7], Cyanex 302 [8], Cyanex 923 [9], Cyanex 272, Tops 99, PC88A [10]. Application of phosphorus based extractants for the solvent extraction studies of Ni such as TOPS 99 [11], D2EHPA [12], Cyanex 272 [2], has been investigated. Separation of Cd(ll), Ni(II), and Co(ll) from chloride leach liquor of spent batteries [13], were explored in the earlier studies. Cd extraction with D2EHPA involves co-extraction of both Ni and Co [14], which causes issues in the separation process efficiency."

Jan 1, 2012

By S. Zhao, S. P. He, M. Y. Zhu, Y. Tao

"The effect of two refining slags (A: 1.0–1.8 CaO/Al2O3 ratio, 11–20 wt% SiO2; and B: 1.0–1.2 CaO/SiO2 ratio, 25–35 wt% Al2O3) on the inclusion morphology of a carbon structural steel (Q235B) was studied by controlling the balance between the steel and the refining slag at 1600ºC in a Si–Mo resistance laboratory furnace. The results showed that most of the inclusions in the molten steel balanced with slag A were formed by a lowmelting CaO–MgO–Al2O3–SiO2 system with a total oxygen content (T[O]) being fixed at 6–13 ppm. The inclusions in liquid steel balanced with the slag B were mostly formed by the CaO–MnO–Al2O3–SiO2 system, with T[O] controlled to 19–26 ppm. The overall size of the inclusions under balance conditions was higher in the steel reacted with the slag B than that reacted with slag A, with the latter showing more inclusions smaller than 3 um. In order to generate a large number of spherical CaO–MgO–Al2O3–SiO2 inclusions smaller than 3 ??m while decreasing the T[O] in the resulting steel, the composition of slag A should be used. This composition allowed improving the cleanliness of the slab, and is also advantageous for the castability of the molten steel. IntroductionThe sample used in this study was a typical carbon steel manufactured by CQ Steel. The galvanized, tinned, and plastic composite steel plates made of the original plates are used extensively for decorative panels, general dust pipes, drums, instrument cases, switchboxes, and train cars, among other uses. The target control composition is shown in Table I. The S and P contents are usually fixed during production below 0.020 and 0.025 wt%, respectively, with the aim of reducing longitudinal cracks on the slab surface."

Jan 1, 2017

By Maynard H. Jameson

EARLIER investigations of the potential-drop-ratio method of electrical prospecting have indicated that under suitable conditions this method is well adapted to the location of formation boundaries in stratified ground. A description of this development was given several years ago by H. Lundberg and Th. Zuschlag.1 The curves published by these authors for the potential-drop-ratio variation above a horizontal contact indicated a definite relation of the position of the curve peak to the depth of the interface. The theory underlying this relation was subsequently studied by Z. Mitera in greater detail,2 and the theoretical deductions were compared with the results of tank experiments. The investigations available at this writing were confined to studies of horizontal formation boundaries. It is the purpose of this paper to extend the scope of the previous work to the problem of dipping layers. THEORY Consider the case of three media of different resistivities, whose interfaces are not parallel. If a point-source is located in one of these interfaces, its images do not lie in a straight line, but on the circumference of a circle whose center is at the hypothetical junction of the interfaces. R. F. Aldredge3 determined the relation that exists between the degrees of dip of the two interfaces and the distances between the various images and the point for which the potential is to be found. As seen in Fig. I, three media of resistivities po, pi, and p2 are involved, and the source I is located at the interface of the media (po) and (pi). The perpendicular depth of the lower interface is h,? is the dip, R is the distance between source I and potential point P, and r is the distance between the images and that point. To distinguish between images lying above the ground interface and those below, the notation "odd" and "even" images will be employed; images below the ground interface will be termed "odd" and those above "even." The following relations govern the distances between either kind of images and the potential point: [ ] As previously pointed out, the images of the source are on the circumference of a circle. If the angle of dip is ?, the angle measured from the horizontal to the first image is 2? to the second image it is 4?,, and so on. Since the limit of the reflecting interface is at its outcrop, the last possible

Jan 1, 1941

By T. R. Kostecki, A. J. S. Spearing, G. S. Esterhuizen, K. V. Jessu

Discontinuities are geologic occurrences in rock and when present within a pillar, reduce the strength of the pillar. Empirical formulas that are commonly used to determine pillar strength do not explicitly take into account the presence of discontinuities and thus can overestimate the pillar strength. The effect of discontinuities on the strength of pillars has been investigated using numerical models, but in these models, the discontinuity strike was parallel with the pillar faces. In this study, fully three-dimensional hard rock pillars were simulated using numerical modeling to understand the effect of the discontinuity dip direction on square and rectangular hard rock pillars. Based on the results, recommendations to assess a pillar’s strength in the presence of a discontinuity are discussed.

Jan 1, 2018

By H. A. Bilgin, A. Özgenog?lu, G. Kaçar

In this study, the influences of rock mass properties on the blasting performance in open cast mines are investigated. To this end, discontinuity spacings and discontinuity orientations are measured and full scale blasts with various designs are observed in open cast mines of Aegean Lignite (ELI) and Bursa Lignite (BLI) Establishments belonging to Turkish Coal Enterprises (TKI). For each blast, blasting cost is calculated, and particle size distribution representing the fragmentation of muckpile is determined by means of Split-Desktop software using image processing. 50%(K50), 80%(K80) passing sizes and topsize values are used in the determination of blasting performance according to rock mass properties. The relationships between orientation angle, which is the acute angle between the strikes of slope face and major discontinuity, and 50%(K50) and 80%(K80) passing sizes and topsize values and also blasting cost are investigated in order to analyse the influences of major discontinuity orientation on fragmentation and blasting cost. Furthermore, the relationships between discontinuity modal spacing (or block size index) and 50%(K50) and 80%(K80) passing sizes and topsize values and also blasting cost are investigated in order to analyse the influences of discontinuity spacing on fragmentation and blasting cost. In this paper, the trends observed in these relationships are discussed and the importance of it in mining is commented. Dans ce travail, Il a été traite les influences des qualites des rocheux massif sur les performances des abattages de l’excavation a ciel ouvert. Dans ce cas, les excavations a ciel ouvert dans les Entreprises Lignite d’Aegean et de Bursa qui appartient a La Societe Charbon de la Turquie; Il a été mesuré le trou du discontinuite et l’orientation du discontinuite et aussi, Il a été observé les abattages qui sont pareilles aux critaires exactes. Pour chaque abattages, Il a été fait le control des expences et la distribution du particle au dimension du pile qui a été deja abatté, a été trouve en utilisant le Software du Split-Desktop. Pour determiner les influences des qualites des rocheux massif sur les performances des abattages, Il a été utilisé K50, K80, et le plus grand valeurs des dimensions. Aussi pour determiner l’influence sur l’orientation du discontinuite majeur de la fragmentation et les expences de l’abattage, Il a été observé les relations entre l’angle de l’orientation ( C’est l’acutage entre la direction du banquette front et la direction du discontinuite majeur ) et les plus grand valeurs des dimensions et les expences de l’abattage. Plus, pour determiner des influences du trou du discontinuite sur l’abattage et la fragmentation; Il a été observé la relation entre l’index de la dimension du block et K50, K80 et les plus grand valeurs des dimensions et aussi les expences de l’abattage. Pour conclure; on peut dire que dans cette presentation, apres la discusssion des sujets consideres ces relations, Il a été souligné l’importances de ces relations dans la domain de la Minéralogie. In dieser Studie wurden die Einflüsse von Gesteinsmasse Eigenschaften auf die Sprengleistung in Tagebau Bergwerken untersucht. Zu diesem Zweck wurden Diskontinuität Abstände und Diskontinuität Orientierungen gemessen und Sprengungen im Originalmaßstab mit verschiedenen Anordnungen in Tagebau Bergwerken der Ägäischen Braunkohle (ELI) und Bursa Braunkohle (BLI) Betrieben, die zu der Türkischen Kohlegesellschaft (TKI) zugehörig sind, beobachtet. Für jede Sprengung wurden die Sprengkosten berechnet und die Teilchengrößenverteilung zur Darstellung der Aufteilung von Haufwerk ist durch Mittel von Teilbelegungssoftware, das Bildverarbeitung verwendet, bestimmt worden. 50% (K50), 80% (K80) durchlaufende Größen und Spitzengröße Werte wurden zur Bestimmung von Sprengleistung geordnet nach Gesteinsmasse Eigenschaften benutzt. Die Beziehungen zwischen Orientierungswinkel, welches der scharfe Winkel zwischen den Streichen der Hangfläche und Hauptdiskontinuität ist, und 50% (K50) und 80% (K80) durchlaufende Größen und Spitzengröße Werte sowie Sprengkosten wurden untersucht, um die Einflüsse von Hauptdiskontinuität Orientierung auf Aufteilung und Sprengkosten zu analysieren. Außerdem, wurden die Beziehungen zwischen Diskontinuität modal

Jan 1, 2003