Search Documents

By S. Moussa

The formation of boron-doped nickel aluminides Ni3AI, (76 at. % Ni) from elemental powders by reaction synthesis using reactive sintering was studied. The process involves the mixing of elemental powders of nickel and aluminium with various wt % of boron up to 1 wt % boron. Nickel and Aluminium powders were mixed in the correct proportion to form the intended boron-doped nickel aluminide intermetallic. XRD, SEMI EDS, Image analysis and Archimedes principle; were used to study the effect of Boron addition on the final microstructure, bulk density, average grain size of as reactively-sintered nickel aluminides (boron-doped), compared with no boron addition. The results showed that at greater boron content than 0.3 wt %, a two-phase non-equilibrium microstructure of consisting of NiAI phase in NiJAI matrix was formed that have been primarily retained even after heat treatment for 5 hours at 1000 °C. Boron was present in solid-solution within both the NiAI and the Ni3AI (in greater amounts) phases.

Jan 1, 2001

By J. A. Bowers

THIS investigation of the effect of bottom shape and life on slag volume was carried out in two Lectromelt top-charge furnaces whose rated capacity is 1000 lb per hour. Unfortunately, just as the work [ ] was started, our steel tonnage was reduced approximately one half, therefore we did not accumulate enough data from which to draw any definite conclusions. Furthermore, the life of the linings in these furnaces was greatly decreased by intermittent operation, which was a further handicap in making a study of this kind. The weight of the heats from which the data were taken varied 1200 lb but all the information was corrected to the standard weight charge for these furnaces of 4500 lb. Almost all the heats were plain carbon; a few contained a small percentage of added copper.

Jan 1, 1947

By Paul Worsey, Richard P. Ayres, Mark F. C. Schmidt

A new alternative technique designed to reduce rock scatter and flyrock during boulder blasting is being developed at UMR. The method uses small explosive charges and is designed for shooting in close proximity, while utilizing common blasting products found on the operators’ site. This ongoing work is being conducted internally as graduate and undergraduate level research. A paper describing the general technique was published in last year’s proceedings. This particular portion of the work was performed as an undergraduate research project as part of the requirements for the explosives emphasis degree option at UMR. Previous model work was performed using cubes of concrete. However, in real life boulders are often flat and irregular rather than perfect cubes. The purpose of this work was to determine how to deal with flatter boulders. The work comprised using different geometry blocks (simulated boulders) of the same volume (1 cubic ft.). Square concrete boulders using an 8.5bag concrete mix were cast using different width to height ratios (varying from 1: 1 to 3.7:1). Single 5/8 inch holes were drilled to 2/3 the depth of the blocks, charges placed approximately l/2 way in to the holes and the holes filled with water. The explosive charges comprised ICI Masterdets containing a OSg High Explosive base charge and incremental added weights of C4 explosive. In the experiments, the block height was progressively reduced and to compensate the charge weight was increased until acceptable fragmentation was achieved. It was found that a significant increase in charge wt is required to achieve the same fragmentation as the width to height ratio increases (the boulder becomes flatter). Furthermore, the increase in charge weight required is proportional to the width to height ratio. Basically, you have to use a higher powder factor for flatter boulders.

Jan 1, 2000

By K. V. Sreenivas Rao

Solidification experiments have been conducted to study the effect of interface heat flux and air gap formation on cooling rate of the casting during solidification of Al-4.5wt%Cu alloy. The thermal history of the casting and mold during solidification is recorded using thermocouples connected to computer interfaced data logger. The measured temperatures in the mold are used as input to the IHCP (inverse heat conduction problem) algorithm for simulating multiple heat flux components at the boundary. It is observed that the filling effects induce spatial variation in the thermal field in the mold and casting regions and greatly influence the cooling rate of the casting. The study demonstrates the use of IHCP and in-situ measured thermal profile in analyzing the cooling rate and microstructure.

Jan 1, 2008

By S. J. Laskowski

In potash ore flotation, carried out in NaCI-KCI saturated brine (about 6-7 molar KC1 and NaCI solution), long-chain primary amines are used as flotation collectors. Long-chain primary amines are poorly soluble in water and their solubility further decreases at high electrolyte concentration. For ionic surfactants there is a characteristic temperature (Krafft Point, KP) below which their solubility is too low for micellization. In a previous study, the effect of pH on the KP of dodecylammonium chloride in water was determined [Q. Dai and J.S. Laskowski, Langmuir, 7, 1361-1365 (1991)]. This paper deals with the effect of electrolyte concentration on the KP of dodecylammonium chloride. The derived theoretical relationship between the KP and the critical micelle concentration (CMC) for dodecylamine can be used to calculate the KP for electrolyte concentrations of up to 0.5 mol/L (about 8% NaCI-KCI brine). A simple experimental procedure for the determination of the KP for higher electrolyte concentrations is also described. The results show that the Krafft point of dodecylamine increases from about 17-18°C (in distilled water) to about 80°C at 16% brine saturation.

Jan 1, 2006

By R. Wensel

A composite material consists of two or more dissimilar components. These dissimilar components retain their identities when mixed together and contribute to the properties of the composite. A composite usually consists of two parts, the matrix and the reinforcing material, or extender that is added to the matrix. Typical materials used as the matrix in composites are metals, polymers, and ceramics. The reinforcing material can be added for any number of reasons. For instance, if the matrix is expensive, an inexpensive filler may be added to the matrix to lower the cost of the product without sacrificing properties. An example of this is calcite (CaC03) which is added to systems such as polyvinyl chloride (PVC), to lower the cost. Reinforcements may also serve as a means to enhance the properties of the matrix material. For example, carbon fibers are frequently added to plastics to increase their strength, and glass spheres may be added to plastics to improve flexural strength. Mg(OH)z is added to polymers to give the property of fire retardancy. The latter is the focus of this paper.

Jan 1, 1995

By Atta Ur Rehman, Kwame Awuah-Offei

This paper examines the effect of bucket geometry (cutting-blade profile, floor profile and blade thickness), speed, motor power output and muckpile particle sizes on bucket penetration and draft for rubber tire loaders. The work uses a 1:16 scale model of a load-haul-dump (LHD) in full-factorial experiments to examine the effect of the variables on penetration and maximum draft. The results show that speed and motor output are positively correlated with penetration and draft, and muckpile particle size is positively correlated with penetration and negatively correlated with draft (p < 0.0014).

By Atta Ur Rehman, Kwame Awuah‑Offei

This paper examines the effect of bucket geometry (cutting blade profile, floor profile, and blade thickness), speed, motor power output, and muckpile particle sizes on bucket penetration and draft for rubber tire loaders. The work uses a 1:16 scaled model of a load-haul-dump in full factorial experiments to examine the effect of the variables on penetration and maximum draft. The results show that speed and motor output are positively correlated to penetration and draft; muckpile particle size is positively correlated to penetration and negatively correlated to draft (p < 0.0014). The results show that buckets with a semi-spade cutting nose profile yield the highest penetration (mean 118.30 mm) followed by those with the spade (mean 108.88 mm), which also yield higher penetration than those straight blades (mean 95.19 mm). Bucket floor profile and blade thickness had no significant effect on penetration or draft. Also, we determined that increasing the speed and motor power output, simultaneously, can reduce bucket penetration. Thus, operators should not waste energy for no additional gain or even loss in bucket penetration. Also, the work finds speed and motor power output each combine with muckpile particle sizes to affect bucket penetration. This research furthers our understanding of the effectiveness of different bucket geometries in improving penetration and reducing draft for rubber tire loaders.

Oct 29, 2021

By A Nigam, K Biswas, R Sarkar

Because of the problems with 1st and 2nd generations of Advanced High-Strength Steels (AHSS), a 3rd generation of AHSS steels has become prominent and these steels have properties in between the 1st and 2nd generations of AHSS. However, although the 3rd generation of AHSS is a promising candidate as a replacement for its predecessors, there remain some challenges in processing these steels which are essentially medium Mn (Mn content ~ 5–7 wt per cent) and high Al (Al content ~ 1– 3 wt per cent) steels. The use of conventional casting powders based on the CaO-SiO2 system is unsuitable for high and medium Mn/Al steels. This work investigates the development of CaO-Al2O3- based mold fluxes for casting third-generation AHSS steel. Mold fluxes, with otherwise similar compositions but different C/A ratios, are tested and their crystallisation behaviour is examined using differential scanning calorimetry (DSC). A calcium aluminate phase having a composition Ca12Al14O33 was found to be the main crystalline phase in the mold fluxes. A decrease in crystallisation temperature was observed as the CaO/Al2O3 ratio increased from 1.00 to 1.33. The effective crystallisation rate constant exhibited an increase with decreasing crystallisation temperature, indicating a potential influence of nucleation rate on the overall crystallisation rate and suggesting an anti-Arrhenius behaviour in the crystallisation process of these mold fluxes.

Aug 21, 2024

By CHENCHEN SUN, GUOPING LUO, GUOCHENG ZHANG

Preparation of briquettes by adding CaF2 reagent into the Australian iron ore powder. The structure and morphology of iron ore briquettes during various reduction stages (i.e., Fe2O3→Fe3O4, Fe3O4→FeO, and FeO→Fe) were observed via an ore microscope and scanning electron microscopy. The results showed that CaF2 reacted with SiO2 to form CaO and SiF4 gas during the roasting process. The reduction swelling index decreased from 12.36 to 8.83% when the CaF2 content in the briquettes increased due to CaF2-mediated refinement of the hematite grains during the first stage of the reduction process. Lattice distortion resulting from the presence of Ca2+ in the FeO lattice during the second stage of the reduction process, coupled with an increase in the porosity of the iron ore briquettes and the formation of a low-melting-point slag phase, promoted the anisotropic growth of FeO lamellar crystals, which resulted in an increase in the reduction swelling index from 4.27 to 7.36%. During the third stage of the reduction process, the growth of iron whiskers was promoted by wüstite (FeO) lattice distortion caused by a solid solution of Ca2+ in the FeO lattice; the reduction swelling index increased from 15.61 to 24.72%, resulting in the catastrophic swelling of the iron ore briquettes.

May 27, 2021

By CHENCHEN SUN, GUOPING LUO, GUOCHENG ZHANG

In this study, the conditions of raw materials and fuels were simulated for Bayan Obo iron ore concentrate by adding pure calcium fluoride (CaF2) in various concentrations to Australian iron ore. The mechanism by which the fluorine (F) content of the lattice influenced the reduction swelling properties of the iron ore briquettes during various stages of the reduction process was investigated. The results provide insight into the mechanism governing the reduction swelling process in Bayan Obo ore briquettes, which could be used to direct real?world production practices, particularly those related to the rational utilization of Bayan Obo ore resources.

By H. Sato, R. J. Lipp, I. Iwasaki, K. A. Smith

Selective desliming holds much promise for upgrading low-grade, finely disseminated iron ores that are not readily amenable to conventional flotation. The process is extremely sensitive to the presence of calcium and magnesium ions that are in process water or are released by constituent minerals. The effects of these two alkaline earth ions on quartz were compared through streaming potential measurements, flocculation and cationic flotation tests, abstraction tests and scanning electron microscope studies. Calcium ion, adsorbed as CaOH+, and magnesium ion, attached by heterocoagulation as Mg(OH)2 precipitate, were responsible for the flocculation of quartz suspension and for the depression in cationic flotation of silica in alkaline pulp solutions. Magnesium hydroxide coating could be removed, similarly to adsorbed calcium ion, by complexation with EDTA and polyphosphates.

Jan 1, 1980

By Donald E. Freshcorn

The minimum sulphur level which can be attained during fluid bed roasting of zinc sulfide concentrates is largely determined by the residual sulfates of calcium, magnesium, and zinc. The fractional conversion of these elements to their respective sulfates is derived from semi- empirical relationships, and multiple regression analysis is used to fit the relationships to experimental data from a commercial fluidized bed roaster. The resulting equation shows that the calcine leaving the roaster contains almost no zinc sulfate, nearly all of the calcium is present as calcium sulfate, and the amount of magnesium sulfate formed is primarily dependent upon the roaster temperatures.

Jan 1, 1976

By S Hapugoda, H Han, L Lu

Charcoal produced from Syzygium Zeylanicum trees was widely used in ancient Sri Lankan iron smelting practices. Charcoal made from Syzygium Zeylanicum tree trunks, branches and leaves were analysed by optical mineralogy and SEM and found to contain unusually high concentrations of calcium oxalate (CaC2O4.H2O – CaOx) crystals in plant cells. Partial and full reduction tests of a high-P Brockman ore were conducted at several temperatures with coke and coke doped with CaOx and CaCO3. It was observed that CaOx promoted reduction and generated comparatively more metallic iron in reduced samples. Furthermore, CaOx encouraged phosphorous partition into slag phases than into the metallic iron, suggesting CaOx can a potential alternative fluxing material to calcium carbonate for treating high-P iron ores in ironmaking processes.

Sep 18, 2023

By A. V. Tarasov

In the course of research aimed at improving the performance of the Vanyukov smelting process (VP) for treating sulfur raw materials in a pilot-scale furnace it has been found that an increase in the calcium oxide content up to 12% to 14% in case of smelting to produce high-grade matte results in a decrease in the copper content of slag by 0.05% to 0.3%. The residual copper content of slag can be computed by a formula taking into account an increase in the calcium oxide content of the feed material and that in the slag. In the course of research for improving the performance of the zinc-containing slag fuming process with blowing of the slag bath with combustion products of natural gas it has been found that the silica and calcium oxide contents have an effect on the degree of zinc sublimation. In case of slag containing 24.4% SiO₂ and 6.95% CaO by weight (SiO₂:CaO = 3.51), the residual zinc content of slag was 3.25%. The minimum residual zinc content of 1.95% was obtained in case of slag containing 22.5% SiO₂ and 14.5% CaO by weight (SiO₂:CaO = 1.55). An increase in the CaO content of slag up to 16% by weight with a ratio of SiO₂:CaO = 1.25 to 1.35 permits minimization of zinc losses in slag by achieving a residual zinc content of final slag in the order of 1%.

Jan 1, 2006

By Martin J. Gungl, J. Lyman MacInnis

None of the industry submissions could persuade the Canadian Tax Reform draftsmen that the rate of return has had as much bearing on investors&apos; decisions to invest in Canada as the success records of Canadian ore findings. The goverment opted for the position that mining capital goes where the ore can be found. Many tax incentives which were available until the end of 1971 have been greatly reduced. However, it is still recognized that new ventures in exploration and development of natural resources deserve a break even if there is reduced recognition of the established and highly successful members of the industry unless they continue to search and develop. The latter will also get some breaks for processing beyond the prime metal stage.

Jan 7, 1972

By H. Henao, E. Kohnenkamp, L. Rojas

The slags generated in the copper conversion process are mainly composed of Cu2O-Fe2O3-SiO2 with the compounds CaO and Al2O3 in concentrations up to 10 wt%. The present work contributes to the knowledge of the conversion process, generating experimental data for the diagrams of phases Cu2O-Fe2O3- SiO2-Al2O3 and Cu2O-Fe2O3-SiO2-CaO. The experiments were carried out in a tubular furnace at temperatures of 1150°C and 1200°C under a condition of saturation with tridymite. Once the equilibrium was reached, the samples were fast quenched in water. The phases in the samples were observed in a Scanning Electron Microscope (SEM) and the elemental composition of the phases analyzed by means of Energy-dispersive X-ray spectroscopy (EDS) detectors. The addition of Al2O3 and CaO into the Cu2O-Fe2O3- SiO2 system resulted in an appreciable displacement of the liquidus lines, corresponding to an expansion of the liquid in the tridymite primary phase field. INTRODUCTION The conversion process of copper consists of oxidizing Fe and S present in mattes with 60 to 65wt% Cu (up to 16wt% Fe). This process is separated into two stages: 1- Slag blowing: Fe is oxidized, the addition of a flux such as SiO2 (silica) forms a second liquid phase called slag, this phase is removed from the furnace; 2-Copper blowing: in this stage, the matte with low concentration of Fe (<1% w/w) is again oxidized to remove S as SO2 in the exhaust gases. The product of these two processes is the formation of Copper Blister (> 98wt% Cu) (Schlesinger et al., 2011). Unlike the aforementioned conventional processes, in most Chilean smelters, conversion Peirce- Smith Furnaces are loaded with high copper matte (70–75wt% Cu) (Henao & Moyano, 2016). Due to the low concentration of iron in these matte (up to 5wt%), it is considered that separating the conversion process in two stages is neither operational nor environmentally convenient. Therefore, the process is carried out in a single stage (Pradena et al., 2006), generating a slag phase with a high percentage of Cu2O (wt%Cu>40).

Jan 1, 2019

By Peter Hayes, Evgueni Jak, Taufiq Hidayat, David Grimsey, Denis Shishin

"An integrated nickel flash smelter is operated with Peirce-Smith converters at the Kalgoorlie Nickel Smelter. To improve the partitioning of arsenic between slag waste and matte product, an option to modify the slag–matte chemistry by addition of CaO was analysed. A combination of plant sample analysis, high-temperature laboratory experiments and thermodynamic modeling was carried out to evaluate the process options. The high-temperature experiments involved the re-equilibration of industrial matte-slag samples at 1225 °C and P(SO2) = 0.12 atm, rapid quenching in water, and direct measurement of phase compositions using electron probe X-ray microanalysis (EPMA) and Laser Ablation Inductively Coupled Plasma Mass Spectrometry (LAICPMS). A private thermodynamic database for nickel sulfide smelting and converting was used together with the FactSage thermochemical software package to assist in the analysis of the distribution of elements between slag and matte as a function of CaO addition. The thermodynamic predictions combined with experimental data obtained in this study can be used to characterise the effect of CaO fluxing on the slag–matte thermochemistry during the nickel sulfide converting.INTRODUCTION At the Kalgoorlie Nickel Smelter (KNS), nickel sulfide concentrate is processed in an Outotec-type flash furnace to produce nickel matte containing +47 wt% Ni. Separation of nickel matte and waste slag from the flash smelting is enhanced through settling in the electric arc -heated zone attached to the flash furnace. The flash furnace matte is further processed in a Peirce-Smith converter to produce Ni-rich matte containing +66 wt% Ni (Crundwell, Moats, Ramachandran, Robinson, & Davenport, 2011). Iron silicate-based slag is used in the converting process at KNS. Most of the arsenic is contained in the final matte and very little of the arsenic partitions into the slag. Previous work by Font et al (Font, Hino, & Itagaki, 2003) shows that the distribution ratio of arsenic between calcium ferrite slag and nickel-matte (LAsslag/matte) is significantly higher than that between iron silicate slag and nickel-matte, where LAsslag/matte = (wt pct As in slag)/{wt pct As in matte} (1)"

Jan 1, 2017

By H Park, V Sahajwalla

"Due to the increasing amount of gangues in iron ores, a beneficiation process is required more as a preliminary step for ironmaking process. However, mechanical grinding and washing of iron ore needs tremendous effort that increases operating cost. Therefore, there is a necessity of a novel approach to ironmaking which can tolerate considerable amounts of silica or alumina. In the present study, a high alumina-carbon composite pellet was examined for an ironmaking process. The effect of compositional changes in the CaO-FexOy-Al2O3-SiO2 oxide system on the reduction of carbon composite pellets was investigated in a purpose built thermo-gravimetric analyser (TGA) at 1473K (1200¦C). As a result, alumina increased the reaction rate of carbon composite pellets by increasing surface area, while silica decreased the reaction rate by lowering surface area of samples. Infrared gas analysis assisted with the reaction kinetics of carbon composite pellets through measurement of CO and CO2 in off-gases. This study will assist with establishing the new pelletising method which differs from the conventional fluxed pellets.CITATION:Park, H and Sahajwalla, V, 2013. Effect of CaO-FexOy-Al2O3-SiO2 oxide system on the reduction of carbon composite pellets, in Proceedings Iron Ore 2013, pp 467-472 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

"In the present study, the reduction behavior of composite pellets comprising of iron oxide, synthetic graphite and slags were investigated in a laboratory-scale horizontal tube furnace. Two different types of slags indicating silicate base and aluminate base slags were chosen to examine the effect of slag chemistry on the reduction behavior of pellets. Slag composition of binding materials has influences on the reactions occurring in composite pellets during direct reduction. In-situ high temperature visualization approach was used to observe the slag / iron / carbon interactions at 1773K (1500°C). The off-gases were measured by means of infrared analyzer to determine the reaction rates of the pellets. Different physical appearances during the in situ reaction inferred a strong correlation between the slag composition and internal reactions. In addition, compression tests were conducted to examine physical strength of the pellets. This investigation was carried out to establish feasibility of physical property control of pellets by selecting optimum slag compositions of binding materials INTRODUCTIONCurrently, most of the iron ore mines have facilities that make an ore more usable for the blast furnace operation by improving its physical properties (e.g. pelletizing and sintering). However, during the process, a large amount of fuel is supplied to indurate materials which consequently deteriorate energy efficiency and produce more CO2 emission. Along with increased interests, direct reduced iron (DRI) making process; simply without coke oven or sintering process, has opened the era of clean and environmental friendly iron making process. While some of the established DRI technologies such as Midrex and HYL were restricted to certain locations where natural gas is abundant, coal based technologies using Rotary Hearth Furnace (RHF) such as FASMET and ITmk3 have been developed with regardless of expensive fuel deposit. In addition to the direct use of pulverized non coking coal and fine iron ore, RHF process also has advantages of utilizing waste materials such as EAF dust, biomass and recycled plastics. Nevertheless, there are still many challenges in the coal utilizing technologies as the unprocessed coal and the waste materials contain huge volatiles and ashes. Although recent investigations on volatiles in a RHF process (Sohn and Fruehan, 2005, 2006) have indicated the benefits of coal in terms of iron oxide reduction and have shown feasibility of multi-layer process, carbon composite pellets still have disadvantages because of its weak mechanical bonding strength. As the mixed system with carbon and oxides generates intermediate gases (e.g. CO and CO2) between solid particles, it is difficult to keep its physical state without the help of binding materials. In this reason, industries have been tried to use various binding materials such as bentonite, kaolinite and Portland cement. However, they are still struggling to find out new materials that provide not only sufficient mechanical strength but also metallurgical properties, such as porosity, reducibility and swelling throughout the reduction reaction. Recently, Canadian researchers (Aota et al, 2006) observed enhanced mechanical strength of pellets by using high alumina cement as a binder and concluded that the method could be used to recycle EAF dust as well, but in depth mechanism of reinforced strength has not been concerned. Most of the ashes coming from binders formulate certain type of slag during the reduction process due to its incombustibility. Thus, observation and regulation of slag property is an essential for the control of carbon composite pellet. Yet, only a little thermodynamic consideration from the perspective of slag chemistry has been adapted in the iron and steel making industries as ash has been easily ignored for its tiny proportion. In this study, effect of CaO-SiO2- Al2O3 slag system on the reduction of iron oxide was investigated in terms of"

Jan 1, 2012