Search Documents

By B. MohammadSadeghi, S. Bakhshivash, M. Haghshenas, F. Rahimi

"Spring-Back/Forward in sheet metals is defined as recovery of elastic strain upon unloading in a deformed sheet specimen. Since this phenomenon can cause alternation in the dimensions of a part, leading to irrecoverable compensations, the operative parameters need to be investigated, thoroughly. To assess spring-forward and effective bending parameters, V-shaped bending dies are the most commonly used experimental approach. In the present research, the effect of bending angle and punch tip radius on the spring-forward behavior of an Al-Mg-Si alloy sheet specimen is studied. To this end, a V-shaped die with four bending angles (i.e. 30°, 45°, 60°, and 90°) was designed and fabricated. Specimens with thickness of 2 mm were cut with dimensions of 50 mm×10 mm. Results show that by increasing the bending angle, the spring-forward angle decreases. In addition, smaller punch tip radiuses lead to further spring-forward. The effect of these parameters on the amount of spring-forward angle, strain distribution and homogeneity along sheet thickness was assessed using finite element analysis (FEA). Simulation results show that as the bending angle increases, the strain is developed more homogenously. Finally, micro-hardness test was used to study the effect of strain hardening caused by bending operation on strength evolution. Results show higher hardness trends for the zones in which the maximum plastic strain occurs.INTRODUCTIONPrecise production plays a significant role in the durability of a part. When it comes to sheet metal forming, this issue should be taken into account as an important factor. In order to predict the alternations, bending dies with special geometric parameters (i.e. V-shaped, U-shaped and L-shaped dies) are commonly used (Wagoner, Lim, & Lee, 2013)."

Jan 1, 2016

By Monica R. Garcia, Antonio Alberto S. Correia, Paulo J. Venda Oliveira

"The aim of this paper is to analyze the creep behavior of a Portuguese soft soil stabilized with binders in one-dimensional conditions, based on oedometer creep tests. The study focuses on the analysis of the effect of the binder content and binder type on the creep behavior of a stabilized soil. The results show that the best binder type for this soil, in terms of creep behavior, is composed of Portland cement and fly ash with a dry weight proportion of 75/25, as this promotes the development of secondary pozzolanic reactions. The results also show the decrease in the secondary compression index with the increment of the binder content, since it promotes an increase in the cementation bonds between soil particles. The general analysis of the results shows a clear dependence on C??and qu, until values of qu of 1500 kPa; after that this relationship is negligible.INTRODUCTIONThe geotechnical structures (such as embankments, dams and buildings) built on organic soils exhibit notable creep deformations, which increase the maintenance and exploitation costs and can even compromise their functioning. To attenuate the creep effects of the soft ground, some improvement techniques are frequently used, such as preloading or reinforcing the soil foundations with vertical rigid inclusions, like concrete piles, stone columns or deep mixing columns (DMCs). However, the installation of DMCs in the soft ground induces (via the arching effect) a transfer of stresses from the soft soil to the DMCs, which causes an increase in the creep settlement on the DMCs (Venda Oliveira et al. 2011).Notwithstanding the fact that the creep behavior of clays has been the object of several studies (Leroueil et al. 1985; Mesri and Castro 1987; among others), the study of the creep behavior of soil-binder admixtures has been practically ignored by the scientific community. The few studies on this theme have revealed that a stabilized soil’s creep behavior is dependent on: the type of binder (Venda Oliveira et al. 2013), the binder content (Correia 2011; Bobet et al. 2011; and Venda Oliveira et al. 2013), the stress level applied during the creep phase (Venda Oliveira et al. 2013), the organic matter content of the natural soil (Venda Oliveira et al. 2012; 2014), and the curing conditions (humidity, vertical stress applied during curing, and curing time) (Correia 2011; Venda Oliveira et al. 2012).The aim of this paper is to contribute to a better understanding of the creep behavior of a soil-binder admixture, by examining the results of oedometer creep tests. The study focuses on the analysis of the effect of the binder content and binder type on the creep behavior of a stabilized soil. Additionally, the creep behavior is correlated with the effective vertical yield stress and the unconfined compressive strength (UCS)."

Jan 1, 2015

By D. J. Sweet, B. Seymour, T. M. Emery, M. Armatys, J. P. Bourgeois, W. Johnson

The Spokane Mining Research Division (SMRD) of the National Institute for Occupational Safety and Health (NIOSH) has partnered with a narrow vein, hard rock underground mine to research the effects of the binder content on the elasticity and post-peak ductility of cemented hydraulic backfill (CHB). This is part of a larger study to enhance the long-term integrity of ground support in underground mines. As mining advances deeper and stresses increase, CHB mix designs will benefit if they can be modified to handle higher levels of strain which are induced by an increased stope closure, typically affected by a reduction in stope width and increased mining depth, or through dynamic loading resulting from a local seismic event. This portion of the research examined the impact of reductions in binder and their impact on Young’s modulus, peak strength, and post-peak ductility.

Mar 2, 2022

By C. Guo

The Mildred Lake Settling Basin (MLSB) is the largest disposal site for mature fine tailings (MFT) at the Syncrude Canada Ltd oil sands plant. Over the past years (since 1997), there has been a marked change in the consolidation behaviour of MFT in the MLSB, which is attributed to microbial activity. Methane-producing microorganisms, known as methanogens, have become very active, and large amounts of biogas (mainly methane) have been produced. In certain regions within the MLSB, gas bubbles are released to the water surface of the tailings pond. Continued field monitoring of the MLSB has provided convincing evidence of the rapid densification process (rapid water drainage from the tailings). This phenomenon contradicts the consolidation models for MFT developed over the past 20 years. The above phenomenon has also been reported at the oil sands tailings ponds operated by Suncor Energy Ltd. in Fort McMurray. This rapid densification has caused pumping challenges in the transfer of fine tailings from the Mildred Lake Settling Basin for the creation of composite tailings. The rapid densification of the MFT may also have potential positive effects in accelerating the reclamation of the oil sands fine tailings. A field and laboratory research program is underway to study the mechanism leading to the rapid densification phenomenon. Systematic field investigations were performed to determine the distribution and characteristics of the rapidly densified MFT. Gas bubble distribution on the water surface was mapped to determine the zones of different biological activities in the pond. These field investigations provided solid ground for further experimental and theoretical research. A number of small-scale column tests were carried out to observe the gas evolution and to measure the changes of some geotechnical parameters under different microbial activity. Also, a series of gassy MFT densification tests are being conducted to study the mechanism of the rapid densification of the MFT under microbiological activity. A review and discussion of the research program is given and some preliminary research results are presented in the paper.

Apr 1, 2005

By C. Guo, R. J. Chalaturnyk, M. MacKinnon, J. D. Scott

The Mildred Lake Settling Basin (MLSB) is the largest disposal site for mature fine tailings (MFT) at the Syncrude Canada Ltd. oil sands plant. Over the past years (since 1996), there has been a marked change in the densification behaviour of MFT in the MLSB. Methane-producing microorganisms, known as methanogens, have become very active, and large amounts of biogas (mainly methane) have been produced. Continued field monitoring of the MLSB has provided convincing evidence of the rapid densification process (rapid water drainage from the tailings) at the area with intense microbial activity. This rapid densification has caused pumping challenges in the transfer of fine tailings from the Mildred Lake Settling Basin for the creation of composite tailings. It may also have potential positive effects in accelerating the reclamation of the oil sands fine tailings. A field and laboratory research program was carried out to study the mechanism leading to the rapid densification phenomenon. A review and discussion of the research program is given and some results from the field investigations and small-scale column tests are presented in this paper.

Jan 1, 2007

By Lorenzo Reyes-Bozo, Ronaldo Herrera-Urbina, Pablo Higueras, Alex Godoy-Faúndez

"The copper mining industry in Chile and perhaps in other countries as well is faced with the challenge to implement the best practices in order to achieve a sustainable and more environment-friendly growth. Relationships between mining industry and society have been historically complex due to its environmental impacts. Whereas the ore grade has declined continuously, this has involved an intensive energy and water consumption thus increasing operational costs at different stages of the concentration process. In the case of copper sulphide ore concentration, froth flotation is the main technology used worldwide. The amount of the different chemical reagents used in flotation plants (i.e., collectors, depressants, frothers and modifiers) affects significantly production costs and has a negative effect on the environment as well. The objective of this research work was to evaluate the use of biosolids and their main components (i.e., glucose, proteins and humic substances) as more environment-friendly flotation collectors for chalcopyrite and molybdenite. For this purpose, microflotation tests were conducted in a modified Hallimond tube. In addition, FTIR and zeta potential experiments were performed to investigate the interaction of biosolids with these sulphide minerals. Biosolids and their main components may interact through physical and chemical ways due to different affinities with such sulphide minerals as chalcopyrite, pyrite and molybdenite, which are present in copper sulphide ores. In alkaline pHs, biosolids and their main components make the zeta potential of the sulphide minerals investigated more negative. These results may provide important information concerning the behavior of the main sulphide minerals in the concentration of copper sulphide ores at industrial scale, wherein mill processes could affect their surfaces properties. Therefore, biosolids and their main components may open an opportunity to be used in copper sulphide flotation plants to partially replace conventional reagents, which are more hazardous and less environment-friendly."

Jan 1, 2014

By K. A. Natarajan, M. K. Yelloji Rao, P. Somasundaran

The bacterium Thiobacillus ferrooxidans triggers the surface modification of sulfide minerals to provide hydrophilicity or hydrophobicity for the flotation of sphalerite and galena. The effects of initial cell concentration, period of biotreatment and pulp density on the floatability of the minerals are discussed. With galena, flotation enhancement obtained through sulfuric acid treatment was retarded by biotreatment at all cell concentrations due to chemical effects. Such a decrease occurred for sphalerite only at cell concentrations sufficiently high for bacterial attachment to the mineral surface. The variables affecting surface modification (and, thus, flotation response of the minerals) include the cell concentration used for bacterial conditioning, the period of biotreatment and the pulp density. Although bacterial growth during biotreatment was observed even in the absence of nutrients, such growth was more common in the sphalerite suspension than in the galena suspension. Cell protein estimations suggest that more cells are attached on galena than on sphalerite. Probable reaction mechanisms associated with bacterial modification are discussed.

Jan 1, 1993

By A. W. Khair, M. Ahmad, L. D. Gehl

"This paper presents an analysis of the dynamics of bit wear on the productivity of the continuous miners. Two field surveys have been carried out. The first survey was to assess the impact of bit wear on productivity and production cost. The second survey was to study the wear characteristics of the cutting tool (i.e. magnitude, forms, and mechanisms of bit wear). Primary factors affecting bit wear is identified and laboratory experiments were carried out to study the effects of some of these primary factors on wear in detail. Results indicate that bit wear has a significant effect on the productivity of the continuous miners. Furthermore under the severe geologic conditions (i.e. cutting rock partings and roof and floor rocks) bit wear not only hampers the productivity, but also increases the production cost due to a higher number of bit consumption. This study also indicated that bit wear accelerates beyond 20% of the conical height loss which corresponds to 7% of the weight loss. This increase rate of wear is an indicative of higher abrasion between bit body and cutting material, resulting in a more dusty environment.IntroductionThe high demand for coal production has increased the need for mechanized coal cutting in underground coal mines. Continuous miners have been used in the United States of America for nearly four decades and now presently more than 2000 are in operation. Almost half of the underground coal production of the country is by continuous miners. Today, competition in the coal industry has increased, due mainly to market conditions and legal restrictions, thus placing an emphasis on production, efficiency, and safety. The use of continuous miners has resulted in the generation of respirable coal dust which causes black lung in mine workers. On the other hand, bit wear presents a serious problem as it affects productivity and economy.Much research in the put has been done on energy requirements and mechanism of energy dissipation for ideal rock fragmentation in the cutting process. Recently, dust hazards in underground coal mines as a result of coal cutting has been a great concern to mining engineers as well as environmentalist of the country. In past, much emphasize has been given to fragmentation mechanics (Khair et al, 1989), dust generation due to regrinding (Khair and Xu, 1991) and dust generation due to bit wear (Khair, Xu. and Ahmad, 1992). These studies concluded that dust concentration increased considerably after a bit weight loss of 7% and thereafter the bit should be replaced. Thus, legal restriction by the Mine Health and Safety Administration for the respirable dust concentration in underground might be a factor deciding the level or rate of production using continuous miners. While efforts in research are on reducing dust generation, it is also important and relevant to study bit wear in more detail.Bit wear is affected by three major groups of parameters: (1) machine operating parameters, (2) insitu conditions and (3) properties of rock. Again, past studies have shown that depth of cut, material of tool, position of water jet and velocity of the rotating drum are very important machine operating parameters. The content of the rock/coal material is important as bit wear is usually due to abrasion or adhesion. Diffusive wear becomes dominant only when the temperature exceeds the sensitive range i.e critical temperature. Mechanical tools have indicated that a rise in temperature is a function of drum velocity, properties of cutting material (rock or coal) and properties of tool. Bit wear due to chemical reaction and oxidation art almost negligible in coal cutting."

Nov 1, 1995

By L. D. Gehi, A. W. Khair, M. Ahmad

This paper presents an analysis of the dynamics of bit wear on the productivity of continuous miners. Two field surveys were carried out. The first survey assessed the impact of bit wear on productivity and production cost. The second survey studied the wear characteristics of the cutting tool (i.e., magnitude, forms, and mechanisms of bit wear, Primary factors affecting bit wear were identified. Laboratory experiments were carried out to study in detail the effect of some of these primary factors on wear. Results indicate, that bit wear has a significant effect on the productivity a continuous miners. Furthermore, under severe geologic conditions (i.e. cutting rock partings in roof and floor) bit wear not only hampers the productivity, but also increase the production cost due to a higher consumption of bits. This study also indicated that beyond 20% of the conical height loss (which corresponds to 7% of the weight loss) the rate a bit wear accelerates. This increased rate of wear is an indication of higher abrasion between bit body and cutting material, resulting in a dustier environment.

Jan 1, 1995

By A. W. Khair

This paper presents an analysis of the dynamics of bit wear on the productivity of the continuous miners. Two field surveys have been carried out. The first survey was to assess the impact of bit wear on productivity and production cost. The second survey was to study the wear characteristics of the cutting tool (i.e. magnitude, forms, and mechanisms of bit wear). Primary factors affecting bit wear is identified and laboratory experiments were carried out to study the effects of some of these primary factors on wear in detail. Results indicate that bit wear has a significant effect on the productivity of the continuous miners. Furthermore under the severe geologic conditions (i.e. cutting rock partings and roof and floor rocks) bit wear not only hampers the productivity, but also increases the production cost due to a higher number of bit consumption. This study also indicated that bit wear accelerates beyond 20% of the conical height loss which corresponds to 7% of the weight loss. This increase rate of wear is an indicative of higher abrasion between bit body and cutting material, resulting in a dustier environment.

Jan 1, 1993

Current research in comminution includes efforts to increase the efficiency of mineral processing systems and reduce the amount of electrical energy needed for size reduction. In most mining operations, comminution begins with blasting. Normally, blast design focuses on loosening material for excavation and sizing the product for efficient haulage. It is likely that blasting also results in internal damage to rock fragments within the blast pattern which may provide subsequent comminution benefits. If substantial comminution benefits exist, appropriate modification to blast pattern design may reduce the overall electrical energy needed for mineral liberation.

Jan 1, 1996

By P Cepuritis, G Chitombo a, I Brunton

There is a significant amount of past evidence that links blasting and occurrences of slope failure. Particularly of great concern at Telfer Gold Mine is the effect of open pit blasting on the stability of the footwall slope above the underground portal and the stability of underground structures. For this reason, Newcrest Mining Ltd invited JKMRC to conduct necessary field measurements and numerical modelling with the following objectives:assess the dynamic stability of the footwall slope above the portal; assess the characteristics of current and future blasts in the open pit; and prepare open pit blasting guidelines that will minimise the detrimental effect of blasting on slope stability. To achieve these tasks it was necessary to develop a scaled distance attenuation curve for blast vibrations. In order to validate the developed vibration attenuation curves it was necessary to monitor vibrations from a production blast. Using JKMRC blast design software tools, the vibration of the production blast was also modelled from the blast design and vibration results from single hole blasts. The intention was, assuming that the observed and modelled vibrations were close in terms of frequency and amplitude, to use the software tools to model the vibrations of future blasts and assess their likely effect on slope stability. Numerical modelling of the dynamic stability of the footwall slope was done using the FLAC finite difference code and the UDEC distinct element code. The results of the numerical modelling and of the field measurements of the blast induced ground vibrations were combined into the blast design rules that relate distance between the slope and the blast, charge weight per delay and number of blasts necessary to cause failure of the slope.

Jan 1, 1999

By G. Titichoca

Modification of the blasting process considers that any increase in the energy consumption generates greater benefits if done in the later stages (associated with a larger decrease in energy consumption). Therefore, although the blasting cost is doubled, generating a greater proportion of fines in addition to a weaker ore (because with greater loads and appropriate distribution of explosives a greater number of internal cracks is generated), the reduction of the unit cost that occurs in the grinding stages (SAG and ball mills) generates a positive balance in the overall size reduction process. Codelco Chile, Division Andina, has developed an extensive experimental plan to evaluate the concept of blasting modification applying greater energy. This was implemented in two stages, each including a specific mine sector: La Union and Don Luis. This paper reviews the experience of implementing such blasting modifications at the La Union mine and its impact on the design concepts and the operation of the SAG mill plant

Jan 1, 2007

By P D. Katsabanis, S Kim

A number of small scale fragmentation tests have been conducted to analyze the effects of blasting effort on the grindability of granite, granodiorite, limestone and iron ore. Powder factors were modified, post-blast fragments were screened and drop weight tests were conducted on fragments of different sizes to deliver a variety of specific impact energies. The fragmentation from the drop weight tests has been analyzed to examine the effect of impact energy and powder factor on size reduction. A consistent effect of blasting on the various fractions of the fragmentation distribution has been obtained for all rocks used. The effect of powder factor on the impact fracturing of the rocks has been expressed in a convenient relationship between progeny size, impact energy and powder factor used in obtaining the primary fragmentation. It is clear that explosives consumption affects downstream size reduction; depending on the rock, the effect can be substantial at coarser final sizes but very small in the case of grinding to small final sizes. Differences from the expected trend can be attributed to changes in blast design. As an example, the effect of in-hole collision of detonation waves is analyzed.

Jan 1, 2011

By A J. Moore

The Australian Coal Association Research Program (ACARP) funded project, No C14057, entitled æEffect of Blasting on InfrastructureÆ, has been carried out with the objectives of providing methodologies for the assessment of the strength of infrastructure types and the establishment of responsible and realistic limits. Personnel from Melbourne, Newcastle and Swinburne Universities and Terrock Consulting Engineers conducted the project. Infrastructure types including: conveyors; power transmission towers; wooden power poles; electrical substations; pipelines, bridges; public access roads and underground workings have been investigated by both field studies and structural analysis. Railways, underground telecom cables, dams and industrial buildings have been reviewed using general structural analysis. This paper has been prepared for the mining industry to provide a progress report on the project.

Jan 1, 2007

By W. M. Duncan, F. S. Kendorski, C. V. Jude

After shotcrete had been in use for a short time al the Climax Mine of the Climax Molybdenum Co., Climax, Colo., it was noted that regular longhole undercutting blasts would severely damage or detach slusher drift shotcrete linings. If this were to be a usual occurrence, the widespread application of shotcrete would have to be reexamined or abandoned. Concrete drift linings are affected less by blasting because of occasional significant gaps between the placed concrete and rock and the greater thickness of poured-in-place linings. Research Project Organized A research project was organized to determine: 1) the seriousness of the problem, 2) more complete in-use shotcrete strength data, and 3) possible solutions.

Jan 12, 1973

By Rennie Kaunda, David Streeter, John Kemeny

This paper describes a field/laboratory study that was conducted in cooperation with a mine in Arizona. The primary purpose of the study was to investigate the effect of blasting energy on the crushability and grindability of the post-blast rock fragments. The crushability and grindability of the rock fragments were evaluated through laboratory comminution tests. A secondary purpose of the study was to investigate different laboratory methods for estimating the comminution properties of the rock fragments. In particular, a number of standard rock mechanics tests were conducted and compared with the comminution test results. Finally, the study was used to evaluate new technologies for estimating insitu rock mass strength and for assessing post-blast fragmentation. To estimate in-situ rock mass strength, the specific energy of drilling (SE) was calculated during blast hole drilling utilizing a continuous drill monitoring system. Post-blast fragmentation was estimated using the Split image processing system. Results from the study support the idea that increases in blast energy can enhance crushing and grinding. Also, several simple rock mechanics tests were found to correlate well with the results from standard comminution tests, which could prove to be useful in practice.

Jan 1, 2003

"Large scale open pit mining and quarrying operations dictate safe and reliable pit wall stability. The current approach of employing the particle velocity-scaled charge distance approach to estimate and minimize damage to residential structures is considered inadequate to protect rock slopes. This study utilizes close-in blasting vibration data as input to an advanced 2D numerical code to study its applicability to serve as a predictive tool in terms of blast-induced rock slope failure. Two tri-axial accelerometer stations, consisting of high-frequency and high-amplitude (20 kHz, 100g) sensors, located within ~100m of the blast, but at two different bench levels, were used to monitor a production blasting in a quarry. The production blast consisted of double-decked explosive loads in 155 mm (6 in) diameter holes, with an inter-deck delay of 42 ms, and each deck consisting of 130 kg (285 lb) of emulsionexplosive. The blasting vibration data obtained at the two bench levels were critically analyzed, and thevibration results served as input to the numerical model consisting of a single rock block with a 45 degree persistent joint plane but with specified strength properties, significantly different from that of the intact rock. The model was able to characterise progressive accumulation of damage in the form of micro-cracks along the joint surface as a function of the vibration load from successive explosive decks. The results showed that such a numerical model can serve as a very good diagnostic and predictive tool, when backed up by careful vibration monitoring and further supported by detailed slope monitoring."

Jan 1, 2017

By B Mohanty, A Siamaki, K Esmaeili

Large scale open pit mining and quarrying operations dictate safe and reliable pit wall stability. The current approach of employing the particle velocity-scaled charge distance approach to estimate and minimize damage to residential structures is considered inadequate to protect rock slopes. This study utilizes close-in blasting vibration data as input to an advanced 2D numerical code to study its applicability to serve as a predictive tool in terms of blast-induced rock slope failure. Two tri-axial accelerometer stations, consisting of high-frequency and high-amplitude (20 kHz, 100g) sensors, located within ~100m of the blast, but at two different bench levels, were used to monitor production blasts in a limestone quarry. The production blast consisted of double-decked explosive loads in 125 mm (5 in) diameter holes, with an inter-deck delay of 42 ms, and each deck consisting of 130 kg (285 lb) of emulsion explosive. The blasting vibration data obtained at the two bench levels were critically analyzed, and the vibration results served as input to the numerical model consisting of a single rock block with a 45 degree persistent joint plane but with specified strength properties, significantly different from that of the intact rock. The model was able to characterise progressive accumulation of damage in the form of microcracks along the joint surface as a function of the relatively low vibration load from successive explosive decks. The results showed that such a numerical model can serve as a very good diagnostic and predictive tool, when backed up by careful vibration monitoring and further supported by detailed slope monitoring.

Jan 1, 2017

By \/eena Sahajwalla, Alexander Blagus

This paper reports the effect of using High Density Poly-Ethylene (HDPE)/coke blends on the reduction behaviour of Mn3O4 to MnO at 1000°C. The results suggest that CH4 release increases with increasing HDPE addition. The results show that the rapid release of methane, over only the initial five minutes, limited the interaction of Mn3O4/MnO with CH4. With the devolatilisation of HDPE there was increased porosity in samples containing HDPE, assumed to be the major factor in differences of reduction rates.

Jan 1, 2011