Search Documents

Rendering a solid hydrophobic and solid-fluid particle* attachment in flotation are recognized as not necessarily related (1,2). The attachment is governed by forces of attraction and repulsion which need to be considered. The induction time required for attachment after solid and fluid particle are brought into proximity (3-8) illustrates the point. Laskowski(8) showed that a reduced induction time favoured flotation but detected no change in contact angle, a standard indication of solid surface hydrophobicity. Induction .time is observed in fluid-fluid particle coalescence, there being called a rest time (9-11) The induction time phenomenon is related to the presence of a metastable liquid film (disjoining film (2)) of the continuous phase (water in flotation) which must thin and rupture to permit attachment. The lifetime of this film, which is governed by the rate of thinning and the probability of rupture with thicknesss, depends on a complex interaction of forces. Investigating these forces should help clarify the attachment process. Practical benefits would be improved understanding of slimes flotation (12,13) This paper is concerned with the role of the mobile fluid particle-water interface on the film lifetime, in particular, the role of time-dependent or dynamic interfacial properties resulting from deformation of this interface.

Jan 1, 1975

By Flávio Túlio Busatto, João Bosco Mendes, Marcio de Souza Lana, Raphael Dias de Medeiros, Gabriel Nazareth G. Alcoforado

The sintering process begins at the ignition stage of the surface layer of the mixture to be sintered. This ignition is performed through the heat supplied by a furnace, called "Ignition Furnace", and this burn must have sufficient heat potential to start the agglomeration process. As a result of the horizontal movement and the flow of air passing through the material, this surface firing front is transported until reaching the lower zones of the bed, thus producing the sinter. The higher the calorific value of the fuel used, the more efficient (lower fuel consumption and higher temperature) is the surface burning, thus raising the mechanical strength of the product during the process. Due to variations in fuel quality, keeping the ignition temperature controlled becomes a challenge, so, in this work, a study on the combustion of coke oven gas (COG) was carried out, evaluating not only its stoichiometric but also the most adequate control strategy, in order to maintain the working temperature and still optimize the yield and quality of the sinter produced. Mathematical knowledge, automation, control and industrial combustion were used in order to achieve the expected results.

Oct 1, 2019

A PDP 11/34 computer has been inter- faced to existing instrumentation in a 400 tph rod-mill/ball-mill grinding circuit and programed with a Kalman filter to estimate several unmeasured variables. A dynamic two-size- fraction model of the circuit is used to predict the complete state of the circuit including particle size distributions around the circuit, mass holdups and flowrates, the ball-mill grinding rate, water additions and cyclone parameters. Online measurements of sump level, slurry densities and product particle size are used to update the model values sequentially on a 20-second interval. This procedure results in optimal estimates of circuit variables given the relative reliability of measurements and the accuracy of the model.

Jan 1, 1983

By J. Drzewiecki, J. Kabiesz

Coal mining using longwall methods of mining can lead to intense disturbances of undermined roof strata. The disturbances may extend beyond the extraction area and the resulted rock mass deformations will appear differentiated. In the case of stiff and undermined roof strata, the energy stored in these rock masses may be frequently dissipated in the form of high-energy seismic tremors. Such events can occur if these strata should fail or „free themselves” either from the constrainment of rock environment or from adjacent strata. It has also been found that the amount of the stored energy closely depends on the size and/or slenderness of these strata. Thus, it would be possible to apply specific preventive measures to reduce the energy of mining – induced seismic tremors. The methods are based on artificial disintegration of the structure of energy – storing strata. One of the most efficient methods is a method of directional hydraulic fracturing, which is regarded as an alternative solution from the traditional blasting and hydraulic methods.

Jan 1, 2003

By Arthur Miller, Andrew Weakley, Heather E. Lawson

"IntroductionDynamic failure events in an underground coal mine, or “bumps,” are defined as “the sudden, violent bursts of coal from a pillar or pillars or a block of coal, resulting in a section, the whole pillars, or the solid block of coal being thrown into an open entry” (Peng, 2008). Reports of disastrous and often fatal dynamic failure events date back over one hundred years in the United States. Mining practices and technologies have significantly evolved over the course of the last century, yet these events continue to occur. The events at Crandall Canyon, Utah (Gates et al., 2007) and Brody No. 1 Mine in West Virginia (Barker and McNeely, 2014) are two recent failure events that resulted in a total of eleven fatalities. These events testify to the fact that dynamic failure remains an imperative safety concern. Furthermore, their continued occurrences indicate that engineering controls have proven inadequate at wholly mitigating the problem.Multiple conditions have been associated with the occurrence of dynamic failure phenomena, including• thick, competent strata that can create a bridging effect, resulting in high abutment stresses (Rice, 1935; Holland and Thomas, 1954; Iannacchione and Zelanko, 1995; Agapito and Goodrich, 2000; Peng, 2008; Whyatt, 2008; Whyatt and Varley, 2010)• overburden thicknesses greater than 500–700 ft. (Rice, 1935; Peng, 2008)• a strong coal that is resistant to crushing (Rice, 1935; Peng,2008) or that is “uncleated or poorly cleated, strong…sustains high stress and tends to fail suddenly” (Agapito and Goodrich, 2000)• the presence of sandstone channels or rolls that can serve to concentrate stresses (Iannachione and Zelanko, 1995; Agapito and Goodrich, 2000)• fracturing of strong units above or below the coal seam (Whyatt and Varley, 2010)• slip along pre-existing discontinuities (Peperakis, 1958; Whyatt and Varley, 2010)• multiple seam mining interactions (Campoli, Kertis, and Goode, 1987; Iannachione and Zelanko, 1995; Newman, 2002; Peng, 2008)• mining sequences that can cause anomalously high stress concentrations (Campoli, Kertis, and Goode, 1987; Iannachione and Zelanko, 1995)"

Jan 1, 2015

By Jeffrey Whyatt

Mining coal in deep, gassy strata is difficult, particularly in deep mines of the west. Dynamic failure (bumps, bounces, etc.) is commonplace, particularly where strong sandstone strata are encountered in the overburden. The disaster potential posed by dynamic failure in these mines is examined and found to be significant. Recent trends in MSHA reportable bumping of deep western coal mines have been increasing. Recent clusters of bumps are explored, a number of which have ended badly. The mechanisms of these bumps and their interactions with geologic structures are explored. Significant progress in controlling these hazards depends on a full understanding of their interaction with geologic conditions. It is apparent that not all MSHA reportable bumps have the same mechanism. These reports describe bumping of pillars, rolling of ribs, outbursts of coal, heaving of floor, shaking-induced roof falls, etc. Progress depends on understanding the underlying mechanisms of these events, and then determining which are potentially active at a particular location. Designs and other protective measures can then be adapted and deployed appropriately. Explicit consideration of mechanisms also supports extrapolation beyond experience as design extends into new mine geometries, geologies, mining methods and increasing depth. Finally, the goal should not be only to design hazard out of mines, but also to provide assurance that this, in fact, has occurred. Pursuit of this goal has been taken up by a major NIOSH research project. The centerpiece of this project is development of a Dynamic Failure Control Program to monitor evolution of dynamic failure hazards with changing geologic conditions to assure that control and protective measures are appropriately deployed.

Jan 1, 2008

By G. van Aswegen, J. D. Bosman

Gold bearing deposits in the Witwatersrand consist predominantly of narrow tabular conglomerates with quartzite host rock. Extensive mining of these deposits at depth results in significant stresses being induced in the periphery of the tabular excavations. Where remnant pillars are created excessive stresses have resulted in the dynamic failure of the abutments. At the Hartebeestfontein Mine four brittle shear zones have recently been exposed and investigated. For most part, they represent abutment failure into the weaker hangingwall strata, striking parallel to the abutment, dipping towards the stope, with a sense of displacement consistent with closure of the stope from above. These shear zones are similar to those described in various publications by Ortlepp2: they are essentially brittle shear zones characterised by the presence of very finely comminuted ‘rock flour’ on an obviously freshly sheared surface. The angle between the shear zone wall and extension fractures indicate the sense of shear and the intersection of the extension fractures with the shear zone walls define a strong lineation normal to the direction of slip. It is suggested that these structures are referred to as ‘mining induced dynamic brittle shears’. Les gisements d’or du Witwatersrand consistent principalement de conglomérats tabulaires peu épais contenus dans une quartzite mère. Une exploitation poussée de ces gisements en profondeur a pour résultat l’apparition d’importantes contraintes induites à la périphérie des excavations tabulaires. Là où des piliers restants sont créés, des contraintes excessives ont eu pour résultat une rupture dynamique des appuis. Dans la Mine d’Hartebeestfontein, quatre zones fragiles de cisaillement ont été récemment exposées et étudiées. Dans la plupart des cas, elles représentent une rupture des appuis dans les strates moins solides de la paroi suspendue, orientée parallèlement à l’appui, inclinée en direction du chantier d’abattage avec une direction de mouvement consistante avec l’affaissement du toit de la galerie d’abattage. Ces zones de cisaillement sont similaires à celles décrites par Ortlepp2 dans diverses publications: Ce sont essentiellement des zones cisaillement fragiles caractérisées par la présence de « farine de roche » très finement réduite sur une surface évidemment fraîchement cisaillée. L’angle entre la paroi de la zone de cisaillement et les fractures de tension indiquent le sens du cisaillement et l’intersection des fractures de tension avec les parois de la zone de cisaillement définit une forte délinéation perpendiculaire à la direction du glissement. Il est suggéré que l’on se réfère à de telles structures comme des « cisaillements dynamiques fragiles induits par l‘exploitation ». Goldablagerungen im Witwatersrand bestehen überwiegend aus schmalen tabularen Konglomeraten mit Quarzitwirtgestein. Der umfangreiche Abbau dieser Ablagerungen in der Tiefe resultiert in signifikanten Drücken, die auf die Peripherie der tabularen Aushöhlungen wirken. Wo Restpfeiler hergestellt wurden, resultierten exzessive Drücke im dynamischen Versagen der Auflager. In der Hartebeestfontein Grube wurden kürzlich vier spröde Scherzonen freigelegt und untersucht. Zum größten Teil representieren sie Auflagerversagen im Stratum der schwächeren Stollenfirste, parallel zum Auflager verlaufend, in Richtung Abbaustelle abfallend, mit einem gewissen Grad an Verschiebung konsistent mit der Schliessung der Strosse von oben. Diese Scherzonen sind jenen ähnlich, die in den verschiedenen Publikationen von Ortlepp2 beschrieben werden: sie sind im Wesentlichen spröde Scherzonen, charakterisiert durch das Vorhandensein des sehr fein pulverisierten „Gesteinsmehls“ auf einer offensichtlich frisch abgescherten Oberfläche. Der Winkel zwischen der Scherzonenwand und den Bruchverlängerungen deutet die Richtung der Scherung an und die Kreuzung der Bruchverlängerungen mit der Abscherzone grenzt sich gegen eine starke Lineation normal zur Richtung der Lehne ab. Es wird vorgeschlagen, daß diese Strukturen als `vom Abbau verursachte dynamisch spröde Scherungen’ bezeichnet werden.

Jan 1, 2003

By Manfred Hager

The ability of conveyor belts to transport large mass throughputs economically over previously unprepared ground has resulted in this system achieving great and extensive use. A significant component in this development is the conveyor belt itself. The development of high strength steel cord conveyor belts involves the optimising of splice design, the use of excellent rubber material especially in the splice, good craftsmanship during splice production and modern field vulcanisation equipment. The durability of a splice for belts of class St 3000 up to St 790 is expressed by the fatigue strength under dynamic stress. The results obtained with a test method and equipment developed by the University of Hannover indicate the present state of the art in this field. Belts of high nominal strength used on inclined long distance conveyors reach splice fatigue strengths of about 3000 N/mm. The design should only exploit approximately 50% of the fatigue strength determined in the tests as maximum operating stress. IMPORTANCE OF CONVEYOR BELT SYSTEMS The use of conveyor belt technology has expanded considerably over the last decades in the bulk goods transportation sector. Because of the favourable transport costs and the technology's adaptability to specific topographies, belt conveyors frequently represent the most economic solution. When flows of goods are large, as in German lignite mining operations, where masses of up to 40,000 t/h are given, it is the only technically feasible alternative. The use of belt conveyor systems allows the sensible distribution of the waste and the production of the coal (Hager, 1981). But this transportation alternative is also suitable when the masses involved are smaller. Whereas conveyor belts were only suitable for loose bulk goods up until a few years ago, today they are frequently also used for hard rock open cast mines, e.g. in the production of copper ore. Because of the favourable transport costs it is frequently still economic to use mobile crushers with a throughput of up to 10,000 t h 6 which breakdown the large blocks produced y explosives into transportable grain sizes. In many operations, trucks are only used to provide flexibility between the excavator and the crusher, i.e. over short routes, and the long, frequently steep, transport paths to the processing plant or to the spreader are undertaken by belt conveyors (Einenkel et al., 1992). The advantages of belt conveyors, i.e. to cope with large mass flows over inclines and down slopes of up to 1:4 have resulted in this system gaining very extensive use throughout the world. The conveyors can be installed over for the most part unprepared ground with suitable vertical radii, adapted to the locally available belt material. In the process individual conveyor belts with lengths of up to 15 km, and in the underground sector with lift heights of up to 1 km, have been built and operated. This great variety of application possibilities is complemented by a limited ability to pass through horizontal curves. This can be achieved with the help of design measures on the conveyor whilst bearing in mind the characteristics of the belt. STRESSING OF CONVEYOR BELTS IN DIFFERENT TYPES OF PLANT The advantage of conveyor belts compared with other systems is also to be found in the large available service-time window, i.e. the excellent reliability and the low costs of energy consumption and maintenance. It is in particular the reliability of a belt transport system which depends to a great degree on its main component, that is the belt - in all its different types and variations. For this reason, the belt is also given the greatest attention in the development of the individual components, because it is the belt which must be designed optimally with regard to various factors. The specific properties of the conveyor belt then assert a considerable influence on the design and sizing of most other components in a

Jan 1, 1993

By A Taheri, G D. Nguyen, M Karakus, S Akdag

During underground mining operations, rock masses are highly subjected to dynamic disturbance caused by blasting, mechanical drilling and earthquakes resulting in strain burst, slabbing and spalling. The dynamic fracture is a significant manifestation of rock failure in deep underground engineering, and it is of great importance to assess the dynamic fracture behaviour of the rock mass under elevated temperature conditions. The correlation between temperature – and loading rate-dependent dynamic fracture mechanism of strain burst is yet to be established. A good understanding of the dynamic fracture behaviour of brittle rock subjected to high-temperature under dynamic loading is required for the prediction of the damage extent during strain burst, and proper design as well as control of the underground rock structures. In this study, dynamic mode I fracture toughness tests are carried out on cracked chevron notched semicircular (CCNSCB) granite specimens to reveal the dynamic fracture characteristics of the brittle rock. For this purpose, a Split Hopkinson Pressure Bar (SHPB) apparatus is utilised to conduct the dynamic tests with various striker velocities on thermally degraded granite. The dynamic mechanical behaviour of granite after high-temperature treatment is examined and discussed. The dynamic fracture toughness is determined and compared for the specimens exposed to different temperatures at various dynamic impacts. The fracturing processes are recorded by a high-speed camera (HSC), and the crack propagation speeds are estimated by HSC image analysis. In addition, the dynamic fracture process and the coupled effects of temperature and loading rate on the dynamic fracture modes are identified by HSC image analysis. Energy partition characteristics in dynamic fracture of granite are quantitatively investigated.

Nov 29, 2022

By A. S. C. Owili-eger

An efficient state-of-the-art dynamic model to simulate and predict the rate of water production in longwall coal mining operations was developed as a tool for mine planning purposes. The model can also provide an estimate of any potential resultant hydrogeological impacts of an operation via an array of element-specific single-valued parameters referred to as the field rating indices. The computational procedure was designed to fully exploit the benefits of hydrogeotechnology and use a combination of conceptual, physical, empirical, and numerical approaches to define, characterize, analyze, and evaluate flow controlling properties of fractured rock systems. The model presented here provides a dynamic prediction method for highly fractured flow; a practical tool in mine and water control planning; and a cost-effective means of assessing, based on the best available technology, the impacts of mining on the water resources within a mining environment to satisfy local and federal regulatory requirements. Unique features include consideration of laminar and non-darcian flow domains in double-porosity-pressure hydrogeological media.

Jan 1, 1990

By A. S. C. Owili-eger

An efficient state-of-the-art dynamic model to simulate and predict the rate of water production in longwall coal mining operations was developed as a tool for mine planning purposes. The model can also provide an estimate of any potential resultant hydrogeological impacts of an operation via an array of element-specific single-valued parameters referred to as the field rating indices. The computational procedure was designed to fully exploit the benefits of hydrogeotechnology and utilize a combination of conceptual, physical, empirical, and numerical approaches to define, characterize, analyze, and evaluate flow con- trolling properties of fractured rock systems. The model presented here provides a dynamic prediction method for highly fractured flow; a practical tool in mine and water control planning; and a cost-effective means of assessing, based on the best available technology, the impacts of mining on the water resources within a mining environment to satisfy local and federal regulatory requirements. Unique features include consideration of laminar and non-darcian flow domains in double-porosity-pressure hydrogeological media.

Jan 1, 1987

By J. A. Marts

Reservoir properties including porosity and permeability distributions in longwall coal mine gobs have direct application to modeling the flow patterns and gas distributions in the gobs. Proper assessment of these distributions is required to assess gob gas hazards such as spontaneous combustion and explosive methane mixtures and to optimize gob gas venthole operation and nitrogen inertization. Determining the reservoir properties is difficult given that the gob is inaccessible and direct measurements cannot be easily taken. Several techniques have been used by previous researchers and will be discussed. This paper will present the methodology used to model the gob compaction by simulating the sequential extraction of coal. Two Western US coal mines were used for case studies. By determining volumetric strain, the porosity and permeability distributions in the gob can be calculated. The geo-mechanical model predicts an axisymmetric volumetric strain distribution with a steeper slope near the start-up room and a shallower slope near the active face.

Feb 23, 2014

By J. A. Marts

Reservoir properties including porosity and permeability distributions in longwall coal mine gobs have direct application to modeling the flow patterns and gas distributions in the gobs. Proper assessment of these distributions is required to assess gob gas hazards such as spontaneous combustion and explosive methane mixtures and to optimize gob gas venthole operation and nitrogen inertization. Determining the reservoir properties is difficult given that the gob is inaccessible and direct measurements cannot be easily taken. Several techniques had been used by previous researchers and will be discussed. This paper will present the methodology used to model the gob compaction by simulating the sequential extraction of coal. Two Western US coal mines were used for case studies. By determining volumetric strain, the porosity and permeability distributions in the gob can be calculated. The geo-mechanical model predicts an axisymmetric volumetric strain distribution with a steeper slope near the start-up room and a shallower slope near the active face.

By A Whaanga, W Vigor-Brown

IGO Ltd’s (IGO’s) Nova-Bollinger Deposit (Nova-Bollinger) is a magmatic nickel-copper-cobalt (NiCu-Co) sulfide deposit found 160 km east-north-east of the town of Norseman in Western Australia (WA). The deposit is hosted by the Mesoproterozoic rocks of the Fraser Zone, which is part of the Albany Fraser Orogen (AFO). Since mining commenced in 2016, IGO’s Nova Operation (Nova) has mined and processed to 31 December 2020, 5.63 Mt of ore grading 2.04 per cent Ni, 0.86 per cent Cu and 0.07 per cent Co. Nova’s mine geology team (MGT) has used commercially available implicit modelling (IM) and general-purpose resource modelling (RM) industry software systems, to prepare the 31 December 2020 (CY20) update of Nova-Bollinger’s JORC Code reportable Mineral Resource estimate (MRE). This CY20 MRE update was predominantly based on ~386 km of diamond core drilling, with the drill holes having a nominal grid spacing of 12.5 by 12.5 m throughout the mineralised zones of the deposit. Using IM tools, Nova’s MGT interpreted and modelled 22 separate domains from the drill hole logging, assaying results, and the MGT’s underground mapping. These IM closed volumes were then used to control the estimation of MRE variables into conventional industry digital block models using RM and other ancillary software systems. During 2021, a commercial machine learning (ML) software was trialled by Nova’s MGT for preparing block models of Nova-Bollinger’s MRE domains. The motivation for the trial was that the ML process could expedite modelling through the direct creation of a domain coded block model from the drill hole logging. Compared to the industry standard approaches of wireframing or IM, where the modeller usually makes many subjective choices to produce the domain model, ML offers a more objective ‘hands-off’ process for determining the connectivity of domains defined in drill holes. Additionally, the ML process provides a quantitative confidence metric associated with its output that may have utility in mine production and resource classification. In this paper, the results of the Nova-Bollinger ML modelling trial are compared to the MGT’s current workflow for MRE work. The MGT’s conclusions as to the advantages and disadvantages of the IM and ML methods for preparation of MRE domains are discussed. The ML software was also tested as a method of rapidly interpreting geology outside the principal zones of MRE interest. These testing results are also presented in this paper.

Mar 22, 2022

By Eiji Kojima

In this research, dynamic and static load tests were performed on permanent foundation piles which had a pile length of 30 m, 800 mm in outer diameter and 15 mm in wall thickness. In this site the dynamic horizontal load test on a smaller test pile, 12 m in length, 500 mm in outer diameter and 12 mm in wall thickness, was also carried out. The static horizontal load versus horizontal displacement derived from the dynamic load test conformed well to that measured in the conventional static horizontal load test of the pile with 800 mm diameter. Then an attempt was made to predict the horizontal load displacement of the pile with 800 mm diameter based on the results of the dynamic horizontal load test of the pile with smaller diameter of 500 mm.

Jan 1, 2006

By S. Frimpong

Hydraulic shovels are widely used for primary production in surface mining operations. Variability in material diggability, unstructured mining environments and limited space and operator inefficiency affect the performance of these shovel excavators. Dynamic models of the hydraulic shovels are essential for understanding and improving machine performance. This paper contributes to this subject area by advancing hydraulic shovel kinematics and dynamics using the modified Newton-Euler method. A virtual simulator is developed to simulate the hydraulic shovel performance in the ADAMS environment. The simulator is validated with data on shovel geometry and the physical and mechanical properties of a formation in a surface mining environment. The results indicate that a shorter digging time increases the shovel operating power requirements, and that the required peak power increases by 100% when the digging time reduces by 50%. Simulation results also show that a shallow trajectory facilitates the digging process, with 50% reduction in peak power requirements compared to a deep one. This simulator provides a powerful tool for performance monitoring, excavation process designs and structural optimization of hydraulic excavators. This work also forms the basis for developing comprehensive simulator models for automated shovel operations in constrained mining environments.

Jan 1, 2005

Dynamic hydrothermal modeling is a tool that can aid in studying problems associated with hydrothermal ore deposits and can help increase our understanding of the spatial distribution of ore within hydrothermal systems. Models are constructed by a sequence of steps involving development of a conceptual model, followed by its mathematical description in terms of governing equation with accompanying initial and boundary conditions. This equation is then solved either analytically or numerically. The four model types ò that fully describe a hydrothermal 'system are those for fluid flow, heat and ore solute transport, and deformation. At Renison, models have been used to help understand two major exploration problems. These are the controls on ore localisation in dolomite horizons and feeder faults respectively. The types of models used ò have simulated the distribution of all mineral zones, pyrrhotite, and temperature in the dolomites. This has allowed evaluation of the effects on ore localisation by physical and chemical heterogeneities within the dolomite host rocks, and allowed estimation of potential controls in different physical and chemical environments.

Jan 1, 1987

By Henry F. Cooper, Scott E. Blouin

Large jacking test procedures that have been applied to obtain static in-situ rock properties (Ref. 1) have shown that the in-situ rock modulus and strength can be considerably less than what would be obtained from laboratory tests on intact samples. This trend is also expected to be true for dynamic properties, but few dynamic in- situ rock property tests have been conducted. During the past several years, high explosive test procedures have been developed to simulate the airblast and direct induced ground motions (Ref. 2) produced by nuclear explosions . These test procedures load large volumes (up to 10 7 f t3) of the earth with stress levels sufficiently high to produc5 feet of particle displacement over surface areas up to l0 5 ft2. This paper discusses some of the data obtained, and the implications of these results for our understanding of the dynamic response of in-situ rock. DESCRIPTION OF TEST PROCEDURES As shown in Fig. 1, the High Explosive Simulation Technique (HEST) consists of a cavity of uniform height bounded on the sides by a soil berm, above by an overburden of uniform thickness, and below by the test bed on the earth's surface. Horizontal racks of detonating cord are placed in the cavity and detonated at one end of the test bed. This detonation produces an explosive wave that propagates across the test bed, loading the earth with an overpressure pulse that decays with time because of the compression and lifting of the overburden. Since 1964, there have been approximately 40 such tests on test bed areas ranging from a few hundred to l0 5 sq ft., simulating peak overpressure conditions between about 100 and 6000 psi and specific impulses between a few and over 100 psi-sec.

Jan 1, 1971

By P J. Bangerter, J Pan

Optimising for Net Present Value (NPV) with a strategic optimiser such as COMET, Prober-E, Blaser or Minemax has hitherto lacked a dynamic method for analysing the so-called third-order outcomes (such as Carbon emissions) of optimisation within life-of-mine planning. Optimisation, per se, has natural effects on carbon emissions in a life-of-mine plan. Contemporary strategic planning employs a mathematical optimiser to make sense of non-linear data (ie a block model) and produces a best-NPV optimised mining schedule, within a set of constraints. The very act of optimisation influences emissions, and in a dynamic way.

Aug 2, 2023

By Kang-Hyun Kim, Ho-Jong Kim, Jong-Ho Shin, Hoon-Ki Moon

"In urban areas, it is often required to construct additional railway tunnels beneath existing railway tunnels. In this case, dynamic interaction between tunnels at the intersection becomes an important issue, as it amplifies structural behavior causing damage to structures and inconvenience to passengers. In this study, vibration superposition effect at the intersection between existing and newly constructed tunnels is investigated by the numerical method. Dynamic interaction mechanism is firstly examined using simple sine wave load, and then a typical analysis for actual multi-leveled tunnel intersection is performed. The results show that the dynamic amplification due to dynamic interaction of tunnels is 149% at the crown of lower tunnel. This indicates that the vibration superposition effect must be considered when the planning and design of a new tunnel beneath the existing tunnel. 1. INTRODUCTION In these days, there are increasing cases that trains cross without transfer stations in metropolitan areas. Consequently, either tunnel is necessarily to be neighboring or crossing, thus tunnel sections closely located are created as shown in Figure 1. If a new tunnel is constructed beneath the existing tunnel, the vibration due to trains passing through each tunnel can mutually affect. The behavior of coupled vibrations may occur and exceed the allowable structural limit, and cause inconvenience to passengers. Theoretically, when vibration waves are propagated from a source to different locations, amplification or decrease of the vibrations can occur by the principle of wave superposition and interference. Multi-leveled tunnel intersection is one of the cases mentioned above. In the actual tunnel, it is difficult to investigate the vibration superposition effect due to a complex ground conditions and structural geometries. In addition, train vibration itself is multi-source vibration, which cannot be theatrically analyzed. Thus, at the tunnel intersection, train vibration from two tunnels make the problem more complicated."

Jan 1, 2016