Search Documents

By P Waters

BHP Billiton Iron Ore initiated a program in January 1995 at the Mt Whaleback operation in Newman, Western Australia to develop a closure plan for the overburden storage areas (OSA), which have the potential to generate acid rock drainage. The primary research program includes the development of technology for the long-term performance of OSAs with respect to slope stability, surface run-off, erosion, water infiltration and vegetation. The objective is to control acid rock drainage by preventing moisture movement into and through the OSA material. Infiltration to the underlying OSA material and closure costs are minimised due to the presence of the run-of-mine (ROM) cover material. A summary of the field data is presented to illustrate low percolation rates to the underlying OSA and key performance characteristics of the moisture store and release cover system design. Field data collected to date demonstrates that a moisture store and release cover system constructed with suitable ROM material has good potential as a final cover system at the Mt Whaleback site. The performance of the cover system on a sloped surface was significantly different as compared to placing the cover system on a horizontal surface.

Jan 1, 2003

By E. M. De Souza

"A scientific testing program, sponsored by the Mining Industry Research Organization of Canada (MIROC), was undertaken on the surface and underground facilities of Inca's Crean Hill Mine to investigate the effectiveness of using dry drilling with a dust control system.The surface test work consisted of the monitoring of advance rates and bit life white a series of 165 mm holes, wet and dry, were drilled at both mine air (0.69MPa) and high pressure air (1.72MPa). The results, based on statistical evaluations of field data, indicated that penetration rates can be increased by an average of 24% when drilling dry with high air pressure and by approximately 27.5% when drilling dry with mine air as compared with wet drilling under the same conditions. Dry drilling also has the effect of reducing button wear by approximately 69% using high pressure air. The underground test work employed a dust collection system developed for use with large diameter holes (165 mm) and high pressure drilling. The testing program has indicated that an average increase in penetration rate of 35% can be achieved when dry drilling in rock (waste) and of 49% when dry drilling in ore with high air pressure. Although preliminary dust monitoring did not indicate any appreciable increase in dust concentration during dry drilling, further dust monitoring is still required.A comparative cost analysis has indicated the potential for reduction in drilling costs when dry drilling is utilized. Further testwork is to be conducted to develop a reliable dust collection system for underground production."

Jan 1, 1992

Develop a dry dust collector suitable for working faces and belt transfer paints. Approach A filter cartridge with a reverse-pulse, self-cleaning system has been mounted in-to a low profile unit requiring electric power only. How It Works Dust-laden air entering the in-let end of the collector passes through the two inline filter elements. When the elements load to a pre-selected pres-sure drop, they are automatically pulse-cleaned by a "backflush" method using compressed air. When the elements are pulse-cleaned, caked dust material on the filter surface is released, and falls away as lumps. Dust is removed from the collector by an auger mechanism. Features of the collector are: (1) unit is completely self-contained, (2) built-in air compressor for pulse-cleaning, (3) cleaning cycle initiates automatically at a preset restriction, (4) automatic auger discharge of collected dust, (5) detachable extension auger for transporting collected dust, (6) "dust leak" indicator light, and (7) "change filter element II warning light. The collector has been designed as permissible although approval has not yet been granted.

Jan 1, 1981

Develop an alternative to water bath exhaust conditioners (water scrubbers) for permissible diesel equipment used in gassy mines. Background Water scrubbers are a safety device used on diesel-powered vehicles in gassy mines. Exhaust from the engine passes through the scrubber, where it is cooled, and any flames or sparks present in the exhaust are extinguished. This prevents the ignition of combustible mine dust or methane that may be present. Unfortunately, water scrubbers consume large amounts of water and require frequent maintenance. Approach Methods that do not require water replenishment and frequent maintenance were investigated. The dry exhaust conditioning system was selected for investigation because no water is consumed and existing heat exchanger technology can be adapted to underground mine vehicles. In accordance with U.S. Mine Safety and Health Administration (MSHA) requirements, the system was designed to cool exhaust and trap flames and sparks. The U.S. Bureau of Mines (USBM) developed and evaluated a system for large engines and evaluated a second system for smaller engines. Both systems were evaluated on an engine test bed; if warranted, the system was then tested underground.

Jan 1, 1993

By D. Tao

Coal is a major source of energy in the U.S. and more than 51% of the electricity used in the country is generated from coal. Coal cleaning prior to combustion is necessary and often accomplished using wet physical processes at coal preparation plants to remove impurities such as ash, sulfur, mercury. However, the resultant clean coal product still contains a significant amount of impurity due to the fact that impurities are not well liberated from coal particles ranging from several millimeters to inches in size at which wet cleaning processes take place. A cleaner coal product can be obtained if a cost-effective dry process is developed to further clean pulverized and thus better liberated fine coal at the power plants prior to its combustion. The benefit of such a process is a significant reduction in the cost of expensive post-combustion chemical cleaning processes such as flue gas scrubbing employed to meet the stringent environmental air quality regulations. In this study, a novel rotary triboelectrostatic separator (RTS) was investigated for its application to dry cleaning of fine coal samples acquired from the power plants in the state of Illinois. The pulverized fine coal contains well liberated ash and pyrite minerals and is an ideal feed to the triboelectrostatic separator for further cleaning without the use of water or any chemical reagents. The proprietary rotary triboelectrostatic separator (RTS) is characterized by an innovative high efficiency rotary charger, charger electrification, laminar air flow, and specially designed electrodes. Compared to existing triboelectrostatic separators, the rotary triboelectrostatic separator offers significant advantages in particle charging efficiency, solids throughput, separation efficiency, applicable particle size range, etc. Testing with several fine coal samples has demonstrated that this technology can significantly reduce ash content with a process efficiency similar to or better than froth flotation. Important process parameters such as charger rotation speed, injection and co-flow rate, feed rate were investigated for their effects on separation performance.

Jan 1, 2010

By Egbert Burchardt

"Some of the challenges faced by the mineral industry in the future are the need to process low grade ores at the lowest operating cost, to deal with elevated energy cost and to address scarce water resources in some regions of the world. These challenges will increase the demand to develop highly energy-efficient and less water-consuming mineral processing systems. Experience from other industries suggests that HPGRs could help to achieve these goals, due to their high energy efficiency and their ability to be used as dry grinding systems. Historically, HPGRs have been used mainly as tertiary crushers in mineral applications for the production of ball mill feed. In the cement industry, however, HPGR systems have been successfully applied for grinding limestone, clinker and slag to a final product fineness (p80) of between 30 and 90 µm without the need of downstream ball milling. The total energy consumption of HPGR finish grinding systems in the cement industry has been found to be 30 to 50 % lower than in ball mill systems. This leads to the question of whether the same methodology can be adopted in the mineral industry. Such a step would require the use of dry rather than wet grinding systems. Traditionally, dry grinding systems have been only an exception in mineral processing, since most post grinding processes are wet. However, there are successful - mainly ball mill based - dry grinding examples in gold, nickel or iron ore. Experience from some of these dry grinding references are summarized in this paper. In addition, this paper explores two future-orientated questions: What opportunities does HPGR finish grinding offer the mineral industry? What are general conditions and challenges for adopting this technology for mineral applications?"

Jan 1, 2014

By Xuewei Lv, Yuelin Qin, Guibao Qiu, Chenguang Bai

"Blast furnace slag (BF slag), is the main by-product in the ironmaking process, which contains large amounts of sensible heat. To recover the sensible heat, this paper described the hot experiments which were carried out in a rotary multi-nozzles cup atomizer, where the molten BFS was transformed into granules without water impingement; subsequently, a new method-pyrolysis the printed circuited board (PCB) with the hot BFS particle, was proposed for recovering the sensible heat in this study. The gaseous products were analyzed by gas analyzer. The residual of the PCB was analyzed by FT-IR and XRD respectively, and the obtained slag particles were analyzed by XRD.The results showed that it is a feasible process of pyrolyzing PCB powder with the hot BFS particle. The sensible heat of hot BF slag could be converted to chemical heat and a large amount of combustible gas could also be generated during the process.IntroductionDue to the rising of the product cost of blast furnace iron (BFI) and the increasing public awareness of environmental problems, the steel industries have to focus on the energy saving and emission reduction. Blast furnace slag (BF slag) is a byproduct from blast furnace exhaust temperature of 1450°C or so, is a high-quality waste heat resources. In China, the steel industry produces approximately 220Mt ofBFS per year, and the enthalpy of those slags is approximately equivalent to 13.3% of the whole energy consumption in the ironmaking process[!]. It can be seen, recycling waste heat is an important way of energy saving for iron and steel enterprises. The molten slag was treated by conventional water quenching method without any recovery of heat in spite of its huge potential. Also, the water quenching process consumes a plenty of water, pollutes the air and water[2]. Additionally, the extra energy is necessary for the drying process of slag to produce cement. As a kind of secondhand resource which can be reused, the BF slag contains a large amount of sensible heat. To recover the sensible heat of BF slag, three key problems should be considered, which refer to ( 1) the dry granulation of BFS without consuming water, (2) how to recover the heat of slag particles efficiently, (3) how to use the slag particles after heat recovery."

Jan 1, 2012

**Add abstract here**

Jun 1, 2010

By A. Sobering, G. N. Carlson

"This paper describes the conversion of the grinding section of the W a bush Mines pelletizing plant from conventional wet, open-circuit trunnion overflow ball milling, with filtering, and bentonite mixing on a common conveyor belt, to dry, open-circuit, grate discharge grinding, with pug mill mixing of bentonite and water at individual mills.The test work and data on operating economies to justify the cost of conversion are given. It is too early, at the time of writing, to have complete operating confirmation, but data are available. A brief description of the original plant is included."

Jan 1, 1971

By Craig M. Sams

Dry grinding circuits and factors influencing the selection of the most appropriate grinding system for a given ore selection are discussed. Comparisons of the drying, grindability, installed costs and operating costs are presented for several grinding systems.

Jan 1, 1994

By G. Keizer

Cortez Gold Mine (C.G.M.) is located in Lander County, Nevada, approximately 80 miles southwest of Elko, Nevada. It is accessed via Nevada State Highway 306 south from Interstate 80. This operation is a joint venture between Placer Dome U. S. Inc. (60% operator) and Kennecott Corporation (40%). The claims which supply oxide and refractory ore feed to the Cortez milling facility are located in both Lander and Eureka Counties. These include the Cortez and Horse Canyon deposits all operated by C.G.M. Joint Venture. Other deposits outside the C.G.M. claim area include; Fire Creek, Buckhorn, Gold Bar and Tonkin Springs. These deposits all occur along the Battle Mountain/Eureka Trend.

Jan 1, 1993

By Garry Keizer

The Cortez gold mine is located in Lander County, NR, about 130 km (80 miles) southwest of Elko. Cortez Gold Mines (CGM) is a joint venture between Placer Dome US Inc. (60% operator) and Kennecott Corp. (40%). The claims that supply oxide and refractory ore feed to the Cortez milling facility are located in both Lander and Eureka counties. These include the Cortez and Horse Canyon deposits, all operated by the joint venture. Other deposits outside the CGM claim area include Fire Creek, Buckhorn, Gold Bar and Tonkin Springs. These deposits all occur along the Battle Mountain-Eureka Trend. History Mining in the Cortez district began in 1862 with the discovery of high-grade silver ores. Grades in the hundreds of ounces per ton occurred in an area 7 km (4.5 miles) southeast of the current CGM mill site. Underground mining through the Garrison and Arctic tunnels provided the bulk of the ore production between 1864 and 1895. To a lesser extent, the Mill Canyon area also supplied ore until 1930.

Jan 1, 1993

By J. S. Murty

In this paper, a report is given of studies undertaken in a laboratory rod mill to obtain the optimum conditions for the desired particle size distribution for long-distance transportation of coal through slurry pipelines.

Jan 1, 1987

By R. Weinstein, R. Snoby

There are many advantages to upgrading coal with dry jigging technology. The most obvious is the lack of process water, which eliminates the need for fines dewatering and slurry confinement. Dry jigging eliminates the clean coal moisture penalty associated with wet processing. Particulate emissions are virtually nonexistent due to inclusions of fabric dust collectors on all modern dry jig plants. Due to the environmentally kind nature of dry jig plants, installation permits are often measured in days, not months. Coupled with all these advantages there has been a fundamental advance in dry jigging efficiency. All of these advantages have renewed the coal industry’s interest in dry jigging. But, air jigging isn’t right for every application. There are limitations due to particle size, particle shape, moisture, and near gravity content. This paper explores the evolution of dry jigging; reviews parameters important for determining the suitability of dry jigging; compares historical performance data as measured by imperfection, against results from modern dry jigging technology; and presents actual data from modern dry jig installations.

Jan 1, 2006

By R. Snoby

Since its introduction in 2002, the modern air jig has processed a wide array of coals throughout the world. This paper explores the reasons and justifications for the installations and provides case history performance data. Specifically highlighted are air jig plants processing metallurgical coal in Colombia, bituminous coal in the United States and India and lignite in the United States and Spain. Each installation has unique reasons to justify an air jig facility. It is important to note that not all of the justifications were based on the ?most cost effective yield?, normally a mantra for coal preparation plant designers and owners. Dry jigging of coal has long been a proven technique for upgrading coal, the modern air jig, with its improved efficiency and operating systems simply extended the range of applications. In some cases, it even allows market quality coal to be produced when no other option is possible.

Jan 1, 2009

By W. M. Aubrey

Cobbing, as used in this; paper, refers to coarse dry magnetics separation. It is applicable when, by its practice, plant cost can be reduced or the value of its products increased by the removal of a barren or lean reject or a high grade final product. This paper attempts to describe cobbing as it is now being practiced, and also the problems that are of concern to the operator and design engineer. In preparation, 16 plants were contacted, all of which were very cooperative with their time and data.

Jan 1, 1958

"Wet low intensity magnetic separation has been used for the recovery of magnetite for decades. As high-grade reserves continue to decline, low grade magnetite ores are being targeted for iron production. Low grade magnetite mineralisation is typically fine grained and requires fine to ultrafine grinding (P80 40 - 30 µm) to liberate it from, predominantly, silica/silicate gangue matrices. Grinding to such particle sizes requires high power consumption and produces excessive fines which impact negatively on wet magnetic separation and tailings dewatering. In addition, the dearth of fresh water for mineral processing in arid areas impacts negatively on the economic viability of low grade magnetite projects. These challenges have motivated innovation in dry magnetic separation technologies for the beneficiation of magnetite that can be economically applied on a large-scale. Such technology has been developed in the Cyclomag Planar magnetic separator (PMS) invented by South Australia-based Christopher Kelsey of IMPTEC P/L. The significant gangue mineralisation associated with magnetite ores in South Australia is quartz. In this study, the performance of the Cyclomag PMS on the recovery of magnetite mineral from magnetite-quartz blends was investigated. Magnetite-quartz blend were subjected to the PMS at varying control parameters - magnet discs rotation speed, inlet airflow and feeder speed. The study showed a successful dry separation of magnetic mineral from non-magnetics using the Cyclomag PMS. The PMS has potential to effectively recover magnetite mineral."

Jan 1, 2018

By A. F. Bridge

IN order to show the need for gas reserves, their control, and conservation, in California, it is necessary to describe briefly the local conditions under which gas is produced and marketed, to point out the lack of coordination between supply and demand, and to relate the history of efforts to prevent wastage. There are now 24 fields in California producing a surplus of gas over field fuel requirements. They are usually grouped geographically into three divisions, as follows: (I) Los Angeles Basin (Los Angeles and 0 r a n g e Counties), thirteen fields, all casing-head gas. Total daily gas available for sale 125,000, 000 ?cu.ft. (2) Coastal (Ventura and Santa Barbara Counties). Seven casine-head and one dry gas field. total-avail- able daily, 165,000,000 cu.ft. (3) San Joaquin Valley (Kern, Kings, Fresno, and San Joaquin Counties). Four casing-head fields, five dry gas fields, and two producing casing- head and dry gas from different zones. Total available daily pro- ducticon, 475,000,000 cu.ft. Total all fields, 765,000,000 cu.ft. daily.

Jan 1, 1936

By R J. Nicholson, J M. F Clout

As part of an overall strategy to make significant new technological advances for the sustainability of the mineral processing and related process industries CSIRO Minerals has developed a new dry separation device. It represents a technology breakthrough and has the potential to radically change the way in which dry particle size classification is achieved in the minerals industry. Conventional dry separation techniques have limited applications and often suffer from low productivity, high operating costs, low separation efficiency, the need for dust control and a lack of flexibility. In the absence of efficient dry techniques, wet processing is often used. The use of wet processing either requires the introduction of water into a separation process, which causes environmental concerns through the need for water supply and tailings dams or the use of æunfriendlyÆ chemicals for dense media separations that have considerable impact on handling and disposal. Wet processing also increases operating costs due to plant instability, materials handling, thickening, filtration and product drying. The new CSIRO technology exploits a combination of natural and applied forces to achieve specific particle motions that produce size separation. In doing so, many of the traditional shortcomings of dry separation have been overcome. The CSIRO Dry Particle Size Separator is ideally suited for dry size separation applications within the size range 1 mm to 30 ¦mfor moderate moisture levels (2 per cent), have low unit throughput, produce a fixed cut size and are therefore impractical where very high unit capacity and low operating costs are required. This paper presents a review of dry separation devices together with details of the new Dry Particle Size Separator and typical results for a number of materials, including iron ore and quarry dust.

Jan 1, 2002

When mining of ilmenite deposits wet process of preparation is traditionally used. But this method needs large volume of water. The problem of water deficiency is characteristic of many regions of the Republic of Kazakhstan. The Satpayevskoye ilmenite deposit is situated in the East Kazakhstan, its location has problems with water, and the mineralogical composition of rock is unfavourable: rocks contain up to 40 per cent of clays. That is why designers made a decision to use dry process of preparation for processing of these ores. Offered scheme and equipment selection are presented in this paper.

Jan 1, 2003