Search Documents

it may be clearly seen that one of the most rapidly increasing items in mining operations is the cost of the timber alone, to say nothing of the cost of installation. Consequently, any practical means that may be used to lengthen the life of mine timber will greatly tend to decrease mining costs and result in important economies in operation. The four principal agents by which mine timbers are destroyed are, decay, insect attack, fire and mechanical abrasion. Decay and insect attack are credited with more than 50 per cent of the total amount of timber destroyed in the mines. Numerous methods may be used to conserve mine timbers, such as better selection, preparation, storage and segregation. It frequently happens that good timber goes into places where poor timber would do as well, and timber of inferior quality is sent into places where only the best grade should be used. However, the most effective method of conservation is by treatment with some standard preservative to prevent decay. Some of. the benefits to be noted from the use of preserved timbers are; the reduction in operating costs by decrease in timber purchases; cuts down interference with mining operations due to timber failures on main haulageways; prevents excessive falling of roof in entries by maintaining timber in sound condition; conserves timber supplies and makes possible the utilization of inferior woods; reduces the danger of mine accidents; improves mine ventilation; lessens fire hazard. Our experience thus far with preservatives, while not of a sufficient period of time to establish just what length of life we may obtain from timber so treated, results obtained during the past four years indicate that the intelligent use of preservatives will effect sufficient economies in mine timber costs to justify the expenditures made for this purpose. MR. BAKER (Concluding): Now, if there are any questions you gentlemen would like to ask about our particular operations, I will attempt to answer them. J. H. EMRICK (Sullivan Machinery Company, Denver, Colo.) ; I was wondering how much penetration you get. MR. BAKER: We get between one-sixteenth and one-eighth of an inch; it is a dipping process. With pressure treatment you get-a greater absorption; that is, better than one-sixteenth of an inch. As long as there is no mechanical abrasion, it seems to serve the purpose. MR. EMRICK: Does that apply to the condition of the timber before it is treated? If it is perfectly dry, will it absorb more treatment than if it is partly green? MR. BAKER: Certainly; one of the things we do is to have it thoroughly seasoned before it is put into the preservative. We put some green timber into the mine once, and the fungus went after it right away. MR. EMRICK: What was the difference in the depth reached by the preservative? MR. BAKER: It hardly penetrated at all when it was green. It has to be sound and well seasoned. MR. EMRICK: How long was the timber dipped or treated? MR. BAKER: According to the seasoning. If it was well seasoned, it was left in the hot bath for an hour; if not so well seasoned, it was left for about a couple of hours. C. M. BILLINGTON (General Superintendent, Rocky Mountain Fuel Company, Lafayette, Colo.): Have you found it necessary to treat timber that has been charred? MR. BAKER: No. However, I suppose it has the sane effect; in lots of places they char timber for the purpose of treatment. MR. BILLINGTON: Have you ever tried lime and salt? MR. BAKER: No, this is the only thing we have tried, the creosote and the Aczol; the Aczol is a foreign product. WM. LITTLEJOHN: Which I is preferable, the Aczol or the creosote? MR. BAKER: I couldn't say as to that. MR. LITTLEJOHN: Have you had any tests as to the value of either? MR. BAKER: We have had some of the Aczol timbers in service for a little over four years; we have had some creosote timbers in service

Jan 1, 1926

forated, allowing the completion of the removal of wash water. When discharged into the washed nut bin, the coal is moist but carries so little water as to not be objectionable to the trade, nor to give any difficulty from freezing during the coldest weather. The rock and bone from the primary jigs is elevated to a 15-ton bin by means of a single strand scraper conveyor 40 feet center to center operating on a 45 degree incline, carrying 12" x 5" scrapers every two feet. This conveyor travels at a speed of 100 feet per minute and has a capacity of 17 tons per hour. From this bin, this material falls into the third or rewash jig similar in all respects to the first two, which discharges the rock waste directly into a 15-ton refuse bin below and the bone into a short dewatering conveyor which delivers into a similar 15-ton bin from which the bone is taken to the powerhouse. The oversize and water from the shaker screen, the water from the dewatering conveyor for both the washed nut and bone, and the sludge and wash water from the three jigs, are delivered by launders to the first compartment of a three-compartment settling tank. Most of the coarser broken coal is deposited in this tank, from which is it continually removed by a bucket elevator carrying 8" x 5" perforated buckets operated on a 60 degree incline at 200 feet per minute, capable of delivering 25 tons per hour to the 50-ton washed coarse slack bin. The water passes successively through the three compartments of the settling tank and from thence through a six-inch pipe to a centrifugal pump, circulating 900 gallons per minute against a 32-foot head. A four-mesh screen 30" x 72" in the third compartment of the settling tank removes the chips of wood, paper, and the other trash, which otherwise would accumulate in the water. Water is provided from the camp water system, deriving water from the well located in an arroyo bed. During the summer months just passed, the water used, has been 108 gallons per ton of raw nut, or 146 gallons per ton of washed nut. The water meter had not been installed last winter, but it is estimated that operating at capacity, the washery will be found to require only about 75 to 100 gallons per ton of raw nut. It has not been found necessary, nor advisable, to attempt to dry the sludge from the settling tank, nor to save the water from leakage of the tanks and bins. The sludge from the jigs is washed into the settling tank and the sludge from the settling tank is washed through a tile drain to the arroyo. The jigs, shaker screen, circulating pump, washed slack elevator, and the rock handling conveyor, are all driven from line shafts driven by one 40 H. P. motor, each jig driven through a clutch. The belt conveyor and the washed nut conveyor, have separate motor drives of five and seven and a half H. P. respectively. The washer is housed in a corrugated iron building, which is partially heated by steam coils. One attendant is required for operation, regulating the feed of the jigs, the supply of water, removal of the rock, and oiling and maintaining the machinery. The rewash jig is operated only intermittently. About eleven per cent by weight of raw nut is removed as waste and four per cent goes to the washed slack bin. No control analyses of the products have been made; the efficiency of the plant being determined only by the physical appearance of the products; but the washery has been a source of pride and satisfaction to all those connected with it. As mentioned before, it has caused no interruption of operation and it has assisted materially in creating an unprecedented demand for ALAMO nut. MR. CHARLES: If there are any questions, I shall be pleased to endeavor to answer them. MR. LITTLEJOHN: Mr. Charles, do I understand it is the nut only that is washed there? MR. CHARLES: Yes, sir. MR. LITTLEJOHN: What did you say the size was? MR. CHARLES: Through three inch round perforations, retained on

Jan 1, 1926

By J. Grubb

"The undertakings described in the paper titled “Study on correlation of quantified coal rank with self-heating temperature” by Wang and Luo in the November 2015 issue of Mining Engineering (Wang and Luo, 2015) are mathematically sustainable and an acceptable extension of work performed by Smith and Lazzara (1987) for the U.S. Bureau of Mines. The paper is not an accurate explanation of the currently accepted leading practice for determining the propensity of a coal seam for spontaneous combustion. The paper could lead a practitioner to an oversimplified conclusion on how to determine the propensity of a coal seam to spontaneously combust.The spontaneous combustion of coal is a complex and not fully understood reaction. What is understood is that many more factors other than selfheating temperature (SHT) and coal rank are required to sufficiently evaluate the risk of spontaneous combustion in a particular coal seam. A superficial assessment can lead to an improper response to the risk. Some statements on the next steps through an appropriate literature search would have made the authors’ conclusions more credible.The SponCom 2.0 software, updated by the National Institute for Occupational Health and Safety (NIOSH) in 2011, provides a path for evaluating the susceptibility of a coal seam to spontaneous combustion. In addition to proximate and ultimate analyses to establish coal rank, and therefore an estimate of SHT, the program includes the history of heatings, friability, seam thickness, overburden thickness, rider seam presence, pyrite presence, face and butt cleat densities, geothermal source presence and other geological features in the assessment. Mining conditions including floor heave, rib sloughage and rate of advance are also assessed to conclude a propensity for spontaneous combustion."

Jun 1, 2016

By V. M. Troughton

Further pile load testing has been carried out at Canary Wharf to compare the performance of base grouted and ungrouted bored piles founded in the Thanet Sand. The testing regime included three preliminary test piles and two working test piles. The results of these tests are summarised in Table 1 below. Two of the preliminary test piles were located only 14m apart to compare the performance of a base grouted and ungrouted pile in similar ground conditions. The load/settlement behaviour of these two preliminary test piles are compared on Figure 1. All the piles were drilled under bentonite with a drilling bucket. In the base grouted piles four grouting tubes were placed with the reinforcement cage to within 500mm of the pile toe. After the pile had been concreted these grouting tubes were then extended to the pile base by drilling and packers were installed. Grout was then injected into the four tubes simultaneously.

Jan 1, 1991

Discussion at the The Midland Counties Institution of Engineers' general meeting, held in Nottingham on 6th May 1916, included contributions by Bramall E., Bragge G.S. and Watkins W.G. regarding possible measures for reducing energy consumption in coal-winding and pumping by centralising engines, using exhaust steam, improving coal quality and size uniformity, or mechanical stoking

Dec 1, 1916

D. EPPELSHEIMER, * Middletown, Ohio.-The housing of employees has so many and so varied aspects that in order to reach even an approximately correct solution it is necessary to have in mind a few fundamental principles; but it is not possible as yet to write these housing principles in the clear and correct form that is possible with many of our natural laws. Manifestly, the problem depends first on the kind of people it is necessary to house. What is suitable for the Southern unattached negro is not suitable for the married skilled American. The influx of colored labor has affected quite a number of what were satisfactorily housed communities. The second important factor is the relative proportion of the number of employees to the total employable population of the community in which the industry is located. The employer of a hundred men in. a large city has little responsibility in the matter of housing his employees. If he employs 75 per cent. of the employable population in a community of 27,000, as is the case of the company with which the writer is connected, it means a large responsibility. In the establishment of an entirely new plant in a more or less isolated place, the responsibility becomes greater. As engineers, we design and write the specifications for the machinery to accomplish a definite purpose, and proceed to house it, provide the necessary buildings with their accessories in the way of cranes, or heating systems, or sprinkling systems, as the case may be. There is no reason why the operating force should not be built up in very much the same way: design the organization, write its specifications so that the employment department can secure the proper men, and then house that organization with just as much thought and care as is given the plant. In the plant, the various machines will work along certain definite lines and accomplish certain results; but even if we start with the proper organization it takes considerable time to get that organization working together. One of the most important elements to this end is the proper housing of the organization. A man usually spends more time at home than at work. Proper surroundings and a comfortable, convenient house of good appearance exercise an influence that cannot be denied, and an employee situated in such surroundings is far more inclined to follow the policies of his employer and take an active part in furthering them

Jan 5, 1919

(The paper by L. H. De Wald-Tech. Pub. No. 429 was presented at the Boston meeting, September, 1931.) W. A. SCHEUCH, Chicago, Ill.-Since starting up our Hawthorne copper wire plant we have found that wire bars from certain suppliers perform quite differently from those of other suppliers. In attempting to evaluate these bars, we made cross-sections, and in making these cross-sections we found considerable variation in the crystal structure. Indications were that there was some preference in the type of crystal structure. In attempting to find the reason for that we discussed it with the various producers and-also reviewed the literature. Mr. DeWald was assigned to determine the various factors that enter into copper wire bar crystal structure, on the basis that the product was a horizontally cast wire bar of practically identical composition and of recognized good composition for the present quality product sold in the market. Mr. DeWald has asked me to say that he should have made reference to Mr. Dalzell's paper on a theory concerning gases in refined copper. D. K. CRAMPTON, Marion, Conn. (written discussion).-Mr. DeWald has set forth an interesting and thorough exposition of the factors controlling macrostructure of this material. It is particularly interesting to us as it somewhat parallels work we have done on macrostructure of round copper billets for piercing into tubes. Our findings as to the effect of the several variables on macrostructure check Mr. DeWald's. The general principles underlying the two are precisely the same. The fact that we worked with copper deoxidized with phosphorous instead of tough-pitch copper, and round billets cast on end instead of wire bars, does not influence the results. We have found that round billets cast so as to produce large radial grains have greater soundness and density than those with a fine macrostructure. Further, and more important, we have found that the billets with large radial grains show markedly different performance on piercing from those having a fine equiaxed structure. With a given temperature of billet and adjustment of piercing machine, the coarse-grained material requires appreciably lower power for piercing and goes through the operation inn appreciably less time. These two differences are of sufficient commercial importance to warrant exercise of great care in maintaining the coarse structure. It seems probable that much the same phenomenon should hold in the hot rolling of tough-pitch wire bars. We would expect that, other things being equal, the coarse-grained wire bars would roll more readily and require less power than fine-grained ones. Moreover, we believe the differences in initial structure of the wire bars should be largely eliminated in the hot rolling process and during the subsequent drawing and annealing, of wire would be entirely eradicated.

Jan 1, 1932

C. P. SANDBERG, LONDON, ENG : † I think we should all be grateful to the Pennsylvania Railroad Company, and to their chemist, Dr., Dudley, for spending so much time and money in order to solve an important question ; nor are we less indebted to the public spirit which leads them to impart the experience thus gained. In Europe nothing similar has hitherto been done, either by a company or by any private individual. In England the great railway companies employ their engineers in other ways, and do not keep a chemist or specialist to study rails; but even if they did they would probably not publish the results. The chief professional engineers are so occupied with their private practice of railroad construction generally, that they cannot be expected to devote their time and energies to so special a question. The German Railway Union has, in my opinion, missed the real object of its elaborate researches by falling into the error of specifying costly, impracticable tests for rails-tests at the same time which do not infallibly expose the impurities that may be in the rails under examination. There has, therefore, been nothing done on this side of the Atlantic in the way of exhaustive study to determine the best composition for steel rails. America should consequently have full credit for the enlightened example which she has set. I wish, however, to make a few remarks on Dr. Dudley's second paper, a paper which follows very much upon the same lines of argument as the first read three years ago, upon which I have previously touched in my paper on the same subject read at the meeting in August last. If Dr. Dudley had discovered a new metal he could hardly, I think, have taken more pains to prove that he was correct in his first formula for the best chemical composition of steel rails. But I have seen so much done in the way of proof by experiment that I am inclined to think that almost anything can be proved by experiments and by samples. If Dr. Dudley would only give up his formula, which would not suit any country-not even America- * For the convenience of members it has bees thought best to insert the continuation of this discussion at the Virginia meeting in tide place, rather than to delay its permanent publication until the issue of Volume X, Transactions, where it would properly belong. T. M. D., Sec'y, † Sent to the secretary in manuscript.

Jan 1, 1881

ASHBEL WELCH, LAMBERTVILLE, N. J.: Dr. Dudley has given the wear of steel rails under four different conditions. He arrives at the conclusion that the softer rails, or those that from their composition ought to be softer, wear better than the harder. But there is another condition which has an important bearing on the subject, and, should not be overlooked,-the weight on a wheel. With the lighter weights of the past, the softer rails may have worn best; with the heavier weights of the future, the harder may wear best. Weights will probably be increased up to the capacity of steel to bear; then doubtless the harder steel will wear best. A leaden rail with ten pounds on a wheel might carry millions of tons, but with one hundred pounds on a wheel, it would be destroyed by a few thousand tons. So in the days of iron rails, my experience was that the softer rails under light machinery stood better than some of the harder; but under heavy machinery the softer were much the most rapidly destroyed. His doubtless the same with steel. The pounding motion of the wheels loosens or spreads the particles of a thin film of steel; the pull lengthwise on the rail de- * Metallurgical Review, vol. i, page 1. † The remarks as here given, as in the previous discussion on steel rails, have all been written out or revised by the participants in the discussion, and represent, therefore, their mature views. It has been thought that this plan, when it can be carried out without doing any of the speakers injustice in debate, is much to be preferred to a strictly verbatim report. The remarks of Mr. Chanute were sent to the secretary after the. meeting, and although they did not form a part of the actual discussion, there can be no doubt of the desirability of including them in this report. The papers under discussion were “Rail Specifications and Rail Inspection in Europe,” by C. P. Sandberg ; " The Wearing Capacity of Steel Rails in Relation to the Chemical Composition and Physical Properties," by C. B. Dudley, and a Rail Patterns," by A. L. Holley. T. M. D., Secretary.

Jan 1, 1881

By S. H. Logan

Mr. B. Neilly: A week or so ago the Secretary was good enough to forward me an advance copy of this paper by Mr. Logan and it was suggested that I comment on it at this meeting. At that time I was not very certain that I would be here, so I committed my thoughts to paper. As a matter of courtesy to Mr. Logan, I sent him a copy of my proposed remarks and I would like to give you just what I sent to him. Appreciating fully Mr. Logan's ability and many sources of information, one naturally hesitates to question anything seriously set forth as his considered opinion. Neither does one of my political stripe like to accuse him of being too 'conservative.? However, in places his paper reminds me of another general manager of a Canadian bank. While I was still Secretary of the Ontario Mining Association, this general manager wrote asking for our forecast on the current year's mineral production, stating that he proposed to refer to such production figures in his annual address to his shareholders. The request was considered very complimentary to the Ontario Mining Association and, in my opinion, justified a great deal of serious study and effort. Finally, the estimate was prepared and forwarded, showing a modest increase over the previous year's total. Picture our surprise and chagrin on reading his address to find that he predicted not an increase but, if you please, a decline of over $10,000,000. Before I cooled off I wrote asking the basis of such a prediction and got a reply to the effect that men in his position had to be ultra conservative in picturing the future.

Jan 1, 1931

The validity of a steady state assumption made by Adams and Nicol (1986) in the modelling of the elution of gold from activated carbon was investigated. It is shown that the accuracy of the steady state approximation is dependent, not only on the magnitudes of the solution flow rate and reactor volume, but also on the lumped elution rate constant. Under the experimental conditions used by Adams and Nicol (1986) the steady state assumption was inaccurate. This could be circumvented in this instance by applying a rigorous general model which accounts for unsteady state behaviour in the solution and in the activated carbon to the experimental data.

Jan 1, 1997

By M. X. Jia

This paper discusses two mineralogy characteristics that may affect the flotation of sulfide ore. The first one, process mineralogy study on a Cu-Ni sulfide ore shows that valleriite and tochilinite are incline to form on chalcopyrite, pyrrhotite and serpentine surface, and the further guess is that the formation of valleriite and tochilinite may also causes the serpentine transform to talc, so the serpentine surface is a phase of talc or a transition phase from serpentine to talc and this enhances the flotability of the gangue minerals. The second discussion on the flotation behavior of the sulfide minerals from the point of view of the mineral semiconductor character.

Jan 1, 2014

By R. J. Pindred

In his paper, Davis presents an overview of risk. He also introduces the Capital Asset Processing Model (CAPM) as a foundation for selecting the appropriate discount rate for a mining project. While applying portfolio theory is more defensible than the ad hoc adjustment of discount rates, the CAPM is not a panacea.

Jan 1, 1995

By J. P. Zannaras

If we assume that testing of the model started at time C, that time t2 was the instant at which the elastic limit of the material was passed at the points of the maximum stress, and that at time t3 the failure of the model was completed as shown in the typical photograph (Fig. 1), then actually the photograph shows the final results of what took place between time t2 and t3. By the principle of similitude all conclusions drawn from the behavior of the model were applicable and valid for actual mine roofs up to the time t, after time t, motions and friction came into play during the destruction of the model. The events between t2 and t3 and the photograph itself are not representative of the events expected in an actual mine roof unless corrections imposed by the principle of similitude are made.

Dec 1, 1956

By R. Bouzaiene

In the paper presented by F.W. Brackebusch on the “Basics of paste backfill systems,” paste fill was presented as a backfill process that offers many advantages over other alternatives such as hydraulic fill and rockfill. It was observed, however, that the mechanics of paste-fill transportation in pipelines is not fully understood and that the success of its implementation in practice depends on the precise control of the proportions of fines, aggregates and water in the mixture. The author emphasized the necessity for laboratory and full-scale testing to determine the suitability of a material to be used as paste fill. Although experimental testing is definitely an important operation in the design of a reliable paste fill, advances in the understanding of the fundamental laws that govern paste flow in pipelines are equally relevant. Ideally, the results of such efforts would provide predictive models for the rheology of the paste and the corresponding pumping-energy requirements. In an attempt to achieve this objective, an ongoing research program has been active at McGill University’s Department of Mining and Metallurgical Engineering.

Jan 1, 1995

By Pierre Mousset-Jones

I wish to submit this discussion item on an article published in the August issue of MINING ENGINEERING by Wala and Altman on the use of canonical diagrams for mine ventilation networks. The advent of computer graphics and plotting has enabled complex underground mine layouts to be displayed and plotted in a variety of three-dimensional formats that very closely represent the actual mine layout. This enables the ventilation engineer, who is familiar with the mine, to display the network pressures, quantities, resistances, and fan locations in a way that can be understood by everyone working at the mine. This is important if the ventilation engineer needs to discuss changes in ventilation with production personnel, or escapeway procedures with union personnel. While I can see some of the potential advantages in the canonical ventilation network diagram described by Dr. Wala, it appears to me that the fact that the diagram has no visual equivalence with the actual mine layout means that most mine personnel will find such a diagram almost incomprehensible. The authors have alluded to certain advantages with the canonical diagram. However, I find it difficult to see that these outweigh the fact that almost everything listed can be duplicated in isometric diagrams, and in a manner that is easily understandable to everyone in the mine from the miner to the mine manager. Perhaps the authors could show a clear example comparing an isometric with a canonical portrayal of a mine network showing the information that is immediately available from the canonical network that is not obvious in the isometric diagram. There is in this country a severe problem with the need for ventilation engineering and expertise to be used and accepted by mine management as a necessary part of mine planning. It seems to me that to introduce the requirement for further explanation so that management can understand a canonical network display will hinder more than help the recognition that ventilation engineering needs at so many mines in this country. However, I can see that the canonical approach does have its place in assisting the practicing mine ventilation engineer, wherever he or she exists in the organization chart for a typical mine. In this case, could the authors please indicate the availability of the computer program to compute and plot the canonical diagram for a mine ventilation network.

Jan 1, 1989

By K. Holmberg, D. Herriot

This paper by Mr Mclvor is yet another contribution to the eternal controversy surrounding the benefits, or otherwise, of high circulating loads in closed circuit grinding. Throughout the paper it is difficult to establish whether the author is referring to effects relating to the mill, classifier, or to the overall circuit. Table 1 is put forward as indicating the advantage of operating at high circulating loads. From the two (it would be interesting to see more) product sizing points provided in each case, the conclusions to be drawn are that cases one and two have very similar size analyses. The third case, however, indicates a much flatter curve, that is to say, higher fines production and a very wide spread of size ranges. If the objective of this circuit is to provide a closely sized product with minimum overground slimes to the downstream process, then it would appear to be the less "efficient" by far. No data is given for product pulp densities either. The term "efficiency" should never be used without a careful and clear definition. In this case, "efficiency" is used to express an apparent percentage reduction in operating work index (Bond) from the measured "standard" at 250% circulat¬ing load operation. The Bond calculation is itself based upon

Jan 1, 1989

By K. F. G. Hosking

I read Professor Gaudin's paper with great interest and pleasure because for some time I have held that the chemical aspect of comminution is a subject of considerable importance to the mineral dresser and deserves to be thoroughly investigated. It does seem appropriate, however, to emphasize the fact that "fresh" edges and corners produced by the grinding of solids display enhanced reactivity has been recognized and utilized in the development of certain mineral identification techniques. Some of these techniques are worth noting, not only because they might facilitate research in the aspect of mineral dressing under discussion, but also because they emphasize the fact that many mineral species commonly regarded as being very inert can display a surprising reactivity when in the freshly ground state. In 1951 Isakov published a number of tests for the components of certain mineral species which depend essentially on grinding in a mortar a mixture of the material under investigation with a solid reagent. Thus when stibnite, 4(Sb2S,), is ground with sodium or potassium hydroxide, the antimony is revealed by a momentary development of a yellow color which changes in air to orange-red. Other antimony minerals need a preliminary treatment before the test can be carried out. This consists of grinding with aluminium sulfate, ferric sulfate or potassium bisulfate, and breathing upon the resultant mixture.

Aug 1, 1956

By G. Bräuner

The methods of burst control treated in the authors' very informative paper have been applied in the Ruhr Coalfield, Germany, for more than 20 years and have proved to be highly effective. It might be interesting here to mention a few experiences: • The symptoms of critical stresses when drilling with small diameters ("test drilling") are essentially the same as described. However, we consider the situation safe if these symptoms occur beyond a certain distance ahead of the face. • That safety distance equals three times the seam thickness plus the daily advance. It is the total seam thickness that counts, not merely the mined portion. • Critical stresses within the safety distance are dissolved by so-called destressing measures: drilling with heavier equip¬ment, blasting, or water infusion. • To avoid bump initiation, the destressing operations should begin at the sides of the stressed zone rather than in the middle. • As to water injection, there are two different principles. If the situation is critical already, high pressures are applied for hydraulic fracturing. If the stresses still allow to drill deep holes, the fluid pressure is kept low and acts for a longer time. This is to make the coal break successively instead of violently - a long-term precaution. • When the stresses are very high, destressing is the most appropriate means. We mostly drill with 95 mm-diam (3.7 in. - diam). The techniques in detail are somewhat complex and sub¬ject to modifications. But the general idea is to accomplish burst prevention by controlling the potential burst situations.

Jan 1, 1989

By M. Albrecht

I have been following the discussions on coal degradation started by the article "Degradation process in coal slurry pipe-lines," by M.G. Ayat and B.C. Scott. I agree with Mr. Dasher's comments in January that the title of the article was perhaps misleading as the information appeared to pertain more to processing the coal than to transportation. Specifically, the authors' conclude that the cyclone had an important impact on the degradation. Dr. Ferri's comments on degradation in other physical processes was very correct, handling of coal in a turbulent manner has an impact on the size distribution of the coal. This is one reason that when I design a coal system (mine to rail car) I try to minimize the total number of transfer and processing steps consistent with achieving the desired product specifications. Another area, mentioned in passing in the article, the impact of natural causes and the mining step, is of particular interest to me. A mine in West Virginia had a variation of 50% in the -6.35 mm (-0.25 in.) raw coal depending upon the direction of mining. Since it was a single unit mine, this significantly impacted the final product. Two articles on mining's impact on size distribution are: • Stefanko, R., Chopra, 1K., and Ramani, R.V., 1974, "Mining influence on size consistency and washability characteristics of coal," SME Fall Meeting, September; and • Albrecht, M., and Olsen, D., 1980, "Mining methods impact on coal preparation plant design," 1st International Mine Planning and Development Symposium, September. Both articles presented information on variation of size distribution and cleaning plant performance on a coal depending on the mining method used. Both articles considered a single coal seam at one mining operation. Stefanko's article considered continuous and conventional mining of coal in Pennsylvania. Albrecht's article considered surface, underground continuous, and underground hydraulic mining of a coal in British Columbia. Both concluded that mining methods do impact coal characteristics. I agree with Mr. Ayat's comments in reply to Dr. Ferri's discussion, "... degradation is a multi-faceted phenomenon involving many natural and man-made factors." As efforts are being made to produce a higher quality (lower sulfur) coal, this topic becomes even more important

Jan 1, 1989