Search Documents

By D. J. Houlahan

ABSTRACT Sorting has the potential to massively improve the pro?tability of mining base metal, hard-rock ores. However, several barriers to the increased application of sorting have been identi?ed, including a lack of mineral-speci?c sensors available to the industry. This paper presents the outcomes of acollaborative project to develop an induction-balance sensor speci?cally for low-grade copper and nickelores. A review of the basic principles of induction-balance sensing and of the sensor-rock interaction is presented. Early development and testing of the sensor on ores from the Thompson nickel belt in northern Manitoba is discussed. Shortcomings of the prototype identi?ed in early testing have now been over-come, leading to improvements in design and construction, as well as sensor accuracy. The improve dsensor has now been tested on additional ores from the Sudbury Basin, with good results. A discussion of potential applications is presented and recommendations for future development are made.

Jan 1, 2010

By M. Pineau, G. A. Monteith, M. Laliberte, G. Houlachi

Conventional physico-chemical treatment methods, either hydroxide or sulfide precipitation, can hardly achieve a high removal of selenium from the liquid effluents which can be generated in some metallurgical operations. In weak acid solutions, selenium exists mainly as anionic species (selenite Se03-2 and selenate SeCV2) which, therefore, cannot precipitate as metal hydroxide or metal sulfide compounds. At the same time, neither selenite nor selenate form stable precipitates with the common cations (Ca, Mg, Fe, etc.) that are typically used in water treatment. At Noranda Inc., CEZinc Division in Valleyfield, Canada, the introduction of new discharge requirements for effluent toxicity initiated a R&D program which resulted in the full-scale implementation of a new treatment method for selenium removal. The goal of this paper is to present this new method which is now being patented by CEZinc. The process chemistry will be presented along with pilot-scale developments and full-scale operational results.

Jan 1, 2000

By Hubert den Dikken

ache, especially when it comes to forwarding of small quantities. Air transport is limited to 1.4 explosives on cargo aircraft and 1.4S classified explosives on passenger aircraft, so most samples cannot be transported by air. Ocean transport is a possibility, but due to stowage and segregation regulations of the IMDG code, a very expensive one. Road transport is often the only solution, but high explosives require special trucks with licensed drivers. The solution to these logistic problems is solved by creating a 1.4S (Class C) classification for all high explosives, when packed in special containment vessels.

Jan 1, 1995

By E. Jong, E. Watkins

"The application of passive tracer gas sources in underground mines is particularly useful for long-term tracer studies as well as for studies conducted in permissible areas of underground coal mines. The use of passive perfluoromethylcyclohexane (PMCH) sources has been previously demonstrated in underground mines, but this new work details the testing of multiple, distinct tracer compounds compatible with passive sources. A description of their potential application in mine ventilation systems is also provided. Three tracer compounds are detailed: (1) PMCH, (2) perfluoroethylcyclohexane (PECH) and perfluoromethylcyclopentane (PMCP). The release rates of these tracers were examined over a 180-day period at multiple temperatures. The advantages and disadvantages of these sources are presented, along with potential applications in characterizing ventilation circuits, flow through gob and leakage. IntroductionThe use of tracer gases for ventilation applications is an established practice, with various past research projects conducted using sulfur hexafluoride (SF6). Tracer gas techniques have been applied to assess flow rates, dilutions rates and auxiliary ventilation system efficiencies with quick, reliable and accurate results (Suglo and Frimpong, 2002). Perfluorocarbon tracer (PFT) compounds are a new introduction to ventilation and air modeling applications in terms of ventilation flow characterization (Watson et al., 2007).PFTs are liquids that are characterized by low background presence in air, low reactivity, high detectability and low toxicity. A design was proposed, called a permeation plug release vessel (PPRV), to convert PFTs from a liquid to a gas and then release the gaseous tracer in a controlled manner. The initial concept was originally introduced by Brookhaven National Laboratory and refined later to become the PPRV. The PPRV functions by allowing the volatile PFT liquid to become a vapor in a controlled manner. The vapor diffuses through a permeable silicone stopper at a predictable rate proportional to temperature (Zhang and Cloud, 2006)."

Jan 2, 2018

By E. Jong, E. Watkins

"The application of passive tracer gas sources in underground mines is particularly useful for long-term tracer gas studies, as well as for studies in permissible areas of underground coal mines. The use of passive perfluoromethylcyclohexane (PMCH) sources have previously been demonstrated in mines, but this new work details the development and testing of multiple, distinct tracer compounds that can be used in passive sources. A description of their potential application in mine ventilation systems is also provided. Three tracer compounds are detailed, which are PMCH, PECH and PMCP. The release rates of these tracers were examined over a 180 day period at multiple temperatures. The advantages and disadvantages of these sources are presented, along with potential applications in understanding complicated ventilation circuits, flow through gob, and leakage. INTRODUCTION The use tracer gases for ventilation applications is an established practice, with various research projects being perform with Sulfur Hexafluoride (????6) in the past. Perfluorocarbon tracers (PFTs) however are relatively new compared to ????6, which is proven to be useful in ventilation and air modeling experiments along with other PFTs (Watson, Wilke, Dietz, Heiser, & Kalb, 2007). These liquid tracers are characterized by low background presence in air, inert behavior with other gases, high detectability with a gas chromatograph and low toxicity. A design was proposed called a permeation plug release vessel (PPRV), which initially introduced by Brookhaven National Laboratory to meet those requirements. The PPRV works by allowing the gaseous form of the tracer to diffuse through the permeable silicone stopper and evaporate into the open air on the other side. The PFTs inside the vessels are injected as a liquid but instantly begin to convert to their gaseous phases at room temperature due to high vapor pressures (Zhang, H., Cloud, A.,2006). Previous studies have detailed how release rates change based on plug thickness across various temperatures (Jong et al., 2015), but not on the release rate stability based on temperature across multiple tracers. For use in underground mines passive release sources need to be durable, be simple to manufacture, have customizable and reliable release rates as well as a long operating life. The PPRV vessel provides a steady release of tracer gas that is essential for long term passive release experiments, making it a viable vessel for the PFTs being tested. The PPRV design also allows for vessels to be bundled together to achieve release rates at detectable levels and allows for the capability to run ventilation surveys with multiple tracers simultaneously. The ability to conduct ventilation surveys with multiple tracers using the PPRV bundling design and detection of the PFTs makes testing the tracers and design together a promising potential for complex and long term mine ventilations studies."

Jan 1, 2017

By Stephen C. Tadolini, Robert Hawker, Peter Mills, Colin Grubb, Tom Meikle

"In unfavorable strata conditions, it is often necessary to install additional long tendon support as part of a primary support cycle. Although these support systems provide the required additional stability to the roadway installation does have a significant effect on the rate of development. To overcome the slow cure time of Portland cement-type grouts, the use of two component resin systems, such as polyurethanes and urea silicates, have become favorable. However, concerns over low modulus and creep properties has led to the development of a two-component grouting medium that displays the properties of traditional cable grouting materials with the rapid reaction times of pumpable resin systems. This paper describes product testing, application, surface trials, underground trials, and full-scale applications of the Tekthix System in a dynamic underground environment. INTRODUCTION Single-component cement grouts have been used to anchor long tendon supports for many years. They range from high- to low-slump Portland cement and can be slow-setting to fast-setting grouts. However, current cement grouting systems, which includes the grout and equipment, have some disadvantages: 1. Low-slump grouts require pumps that can handle a thick, high-viscosity grout, so choice of pumps is limited. 2. Pumping distance is limited with current cable bolt grout pumps; operators often tend to add water to allow pumping long distance, which adversely impacts the quality and strength of the material. 3. Fast-setting grouts tend to cause issues with pump and line blockages due to the reduced working life of these single-component materials."

Jan 1, 2017

By William C. Dixon

Since the mid 60's, several haul cycle simulation programs have been developed. However, most of these programs are believed to employ the continuous, rather than the discrete, event-oriented simulation approach to determine the haul cycle times. This paper describes the recently developed haul cycle simulation approach where time is advanced in varying amounts only as the system changes occur. This approach results in greater computational accuracy and increased computational efficiency. The program is written in FORTRAN and requires equipment performance curve and haul road profiles as input. Unique program capabilities include the handling of switchbacks and intersections. The program uses a master data file concept in which various haul road profiles found during the mine life can be simulated all in one job submission. The results of the model validation using the actual time study data provided by an open pit mine operator near Tucson, Arizona, are also described in this paper.

Jan 1, 1978

By C. BARING HORIVOOD

(Chattanooga Meeting, October, 1908.) THIS paper is intended, in the light of recent investigations, to call attention to some of the essential features of good practice in sampling and mine-valuation. Mine-sampling may be divided broadly into two classes : (1) development-sampling and computation of ore-reserves; and, (2) stope-sampling and estimation of stope-values. DEVELOPMENT-SAMPLING. It is with development-sampling only that this paper deals-the term development being taken to mean the opening-up of a mine by cross-cuts, drives, connections, etc., preparatory to actual extraction of the ore for milling. In development-sampling the work of the sampler and the consequent estimation of the probable value of the mine or portions of the mine, as the case may be, cannot be verified until a later period, when the ground thus sampled has been exploited; hence, extreme care and accuracy are essential. Moreover, the development-sampler has to foresee and allow for contingencies which may arise when stoping is started. It follows that the sampling, in development-work, demands familiarity with the conditions likely to be encountered later in actual mining. In stopes, on the other hand, sampling is clone under actual working-conditions, and the sampler's valuations are immediately checked by the gold-output, or in some cases by a second sampling of the broken ore. A stope-sampler therefore need not be an experienced miner, though he should possess sound technical training and work accurately. Should he be somewhat inexperienced, be soon has his errors discovered for him, and learns to avoid them. Taking these facts into account, it is obvious that a mining company employing two or more samplers should

Jan 1, 1909

By Michael A. Barbaglia, Mark William Withey

The lift shot is an essential blast design in the execution of mine creation and expansion plans. Whether it be opening a new quarry, creating a new level in an existing operation, or for control of water, lift shots are utilized to create the desired results. Lift shots by their nature differ from conventional production blasts because they have no free faces for relief of the blast. Due to this fully confined state, the primary direction of the rock movement is vertical, and the potential for excessive vibration and fly rock generation is great.

Jan 1, 1994

This paper is an outline of the developmental practices now in use at North Broken Hill Limited, N.S.W. The description will be given under the following headings.I. General.......opening up of a new level.II. Driving.III. Winzing.IV. Rising.V. Auxiliary Ventilation.VI. Notes on the Introduction of Mechanical Appliances.VII. Office Records and Routine.I. GENERALThe lode, for purposes of description, may be said to be divided into two portions which are usually referred to as the Southern and Northern Orebodies.The southern ore-body is the larger and in places attains a width of 200 feet. The northern ore-body is, generally speaking, comparatively narrow. These ore-bodies have a northerly pitch of approximately 45' and a westerly dip of 60. In the southern ore-body a grid of ore chutes is provided at 31 ft. 8 in. (5 square set) intervals and this necessitates an elaborate arrangement of cross-cuts, portion of which have to be driven through the foot-wall. Crushed country rock adjacent to the foot-wall makes it necessary for drives to be placed at least 60 feet from the lode.In the northern ore-body the ore chutes are arranged along a longitudinal drive, thus making a much simpler layout. These layouts were described in detail by A. R. West (Proceedings A.I.M.M. No. 117). In opening up a new level from the shaft plat, a heading is extended in a westerly direction until a point approximately 60 feet from the footwall of the lode is reached.At this point the direction of the cross-cut is altered to a bearing approximately 90 to the general strike of the ore-body, and the cross-cut continued until the hanging-wall is intersected. From the information obtained together with that from diamond drilling, the outline of the ore-body is plotted as closely as possible, and this serves as a basis for the layout of the level. Drives south and north from the main cross-cut are made in order to determine the southern and northern extremity of the southern ore-body. The former is usually driven in the centre of the ore-body and serves as a permanent gangway and ventilation drive for the new level.From the northern extremity of the southern ore-body, the drive north is...

Jan 1, 1944

By Howard Smith

FOR several years this Institute has recorded in its TRANSACTIONS the various discoveries of potash? in America, and the successive stages in the development of an independent domestic potash industry. This paper is intended primarily to continue the record through the year 1935. In retrospect it is not inappropriate to note that public interest aroused in 1910 resulted in the production of some 1090 tons of pure potash in 1915, as a small beginning in the domestic inorganic potash industry, and that the infant industry thus begun reaches its majority this year, following a record production in 1935 of about 600,000 tons of potash salts and exports to no less than 22 foreign countries, including six countries in Europe. This production, with an estimated 200,000 tons of pure potash, may be compared with a production in 1934 of 430,157 tons with an equivalent of 144,342 tons of pure potash.

Jan 1, 1936

By A. C. Watts

The question of disposition of the slack and dust so troublesome to coal mine operators of the West has been divided by your committee chairman into three heads, viz: The preparation and transportation of fine and powdered coal. The developments along the line of low heat carbonization. The uses to which fine and pulverized coal have been put. The development of low heat carbonization has been assigned to me. This is really not a part of the subject but as it has a most important bearing on the future use of coal, I presume the chairman thought best to include it. An English committee on smoke abatement makes the statement that the burning of raw coal is "dirty, wasteful and unscientific". I will go a step further and characterize it as an "economic crime." It has been predicted by eminent scientific men that eventually no raw coal will be burned for heat or power purposes. All this will take time, experimentation and large expenditure, but it will surely come. The question of disposition of slack and dust so troublesome to coal and utilization of its by-products has been retarded by the abundance and cheapness of the raw coal, and by the abundance of suitable coking coals for metallurgical purposes. But necessity is surely, if slowly, demanding that the enormous waste ensuing from the burning of raw coal for heat and power must cease. For instance, smoke abatement investigations in Manchester, England, showed that the increased cost of household washing was about $1,250,000 per year due to smoke and soot. It is estimated that in London 200 tons of soot and smoke particles are suspended in the atmosphere over that city during dense fogs and that much more than this is emitted from the chimneys each winter day during the forenoon. As an example of what benefits a smokeless fuel gives, it is cited that in the mill town of Shaw, England, the burning of smokeless fuels in the factories has reduced the so-called fogs by about 80%. Necessity, caused by the war led Germany into the field of low tem¬perature carbonization because of the shortage of motor fuel and lubricating

Jan 1, 1922

By B B. Beamish

Long-hole directional drilling for in-seam exploration was introduced to New Zealand at Huntly West Mine in 1989. Following the success of this initial drilling program the Coal Corporation of New Zealand (CoaICorp) purchased its own drilling equipment and proceeded to adopt the technique with in-housetraining. From July 1991 to September 1992 a total of 15 455 metres was drilled at Huntly West Mine. During this period several modifications were made to the drilling technology to suit the ground conditions. The resulting interpretations of the drill information enabled reliable seam definition to be incorporated in mine planning. Since January 1993, the technique has been transferred to the Huntly East Mine to assist with seam definition for the planned development westwards under the Waikato River. The benefits of this drilling technique to coal mine planning are now well documented in Australia and New Zealand as well as other overseas countries. The possibilities of adapting the long-hole drilling technique to hard rock applications has been illustrated recently with successful cross-measure drilling at Huntly East Mine.

Jan 1, 1993

By A. K. Haines, M. W. Godfrey, D. M. Miller, P. C. van Aswegen

The Bacterial Oxidation [(BIOX)] process for the pre-treatment of refractory ores for gold recovery developed by Genmin, the mining division of Gencor, has been operating successfully at the Fairvew Mine since October 1986. The continuous operation of a pilot plant at Genmin Process Research has resulted in further process developmenst to improve plant operating efficiencies. These new developments, which include a higher solids content of the pulp feed to [BIOX], lower retention times, higher operating temperatures, lower power utilizaton for oxygen dispersion and reduced nutrient addition, have all been successfully implemented on the Fairvew plant. It has furthermore been confirmed that the arsenic precipitate formed in the neutralization of effluent solutions complies to the United States of America EPA standards. Contineous cyanidation pilot plant work conducted on [BIOX] product has indicated that cyanide consumption can be drastically decreased if a continuons flowsheet is implemented in preference to a batch leaching system.

Jan 1, 1992

By P. C. van Aswegen

The Bacterial Oxidation (BIOX®) process for the pre-treatment of refractory ores for gold recovery developed by Genmin, the mining division of Gencor, has been operating successfully at the Fairview mine since October 1986. The continuous operation of a pilot plant at Genmin Process Research has resulted in further process developments to improve plant operating efficiencies. These new developments which include a higher solids content of the pulp feed to BIOX®, lower retention times, higher operating temperatures, lower power utilization for oxygen dispersion .and reduced nutrient addition have all been successfully implemented on the Fairview plant.lt has furthermore been confirmed that the arsenic precipitate formed in the neutralization of effluent solutions complies to the United States of America EPA standards. Continuous cyanidation pilot plant work conducted on BIOX® product has indicated that cyanide consumption can be drastically decreased if a continuous flowsheet is implemented in preference to a batch leaching system.

Jan 1, 1991

By R. W. Lawrence

"In the past year, BioteQ Environmental Technologies Inc. have initiated design and construction of new plants to add to an existing list of plants that utilize the BioSulphide® and ChemSulphide™ process technologies for metal recovery and water treatment. In these plants, low cost biogenic sulfide or, in some cases, chemical sulfide reagent is used to selectively remove metals from contaminated water. The process produces high grade, marketable, metal sulfide products even from low grade feed solutions. The revenues generated from the sale of products can allow for water treatment at a profit in some cases, offset treatment costs in others, and generally reduce sludge disposal and management costs. The effluents produced from the process can meet stringent environmental standards. Current plants in operation and under construction range in sulphide demand from 50 kg/day to 3.7 tonnes/day, with the feasibility of larger plants with sulfide demands ranging from 6 to 43 tonnes/day under review.Biogenic sulfide reagent can also be considered for other applications in hydrometallurgy and mineral processing. Uses under consideration by a number of mining companies include: (1) replacement of sodium hydrosulphide in the SART process for cyanide regeneration and copper recovery in the processing of gold-copper ores, and (2) replacement of sodium hydrosulphide for use in the separation of copper and molybdenum in flotation. Biogenic sulphide, produced on demand at site, offers significant cost savings and provides the additional benefit of improved safety due to the elimination of the transportation, handling and storage required for chemical sulphide reagents.This paper reviews the applications of the BioSulphide® and ChemSulphide™ technologies for water treatment and metal recovery, and introduces projects where biogenic sulfide can be applied in hydrometallurgy and mineral processing."

Jan 1, 2007

By P. Cicmanec

Mining activities in the territory of Slovakia have a long history. Mining techniques have developed rapidly in the last centuries. This paper deals not only with mining history, but also with underground brown coal mining, magnesite mining and other mining activities at present and sustainable developments of the mining industry in the Slovak Republic. This paper looks forward in the context of mineral raw materials in Europe (Global Europe, 2012).

Aug 1, 2013

By Tack K

During its 28-year life the MHD ISP smelter has gone through two phases, each of about a dozen years. The first phase was a learning one; in the second phase the lessons were applied and throughput and production rose strongly. Early experience revealed the robustness and the flexibility of the Imperial Smelting Process. The experience was demonstrated by strong increases in the throughput of mixed lead-zinc concentrates and of secondary (oxide) zinc materials. Purchased material quantities rose from 175 000 tonnes/year to 200 000. The required capacity increase of the IS furnace to smelt the higher throughput was achieved by relatively minor modifications; for instance a change to the internal furnace profile gained an extra two square metres in cross sectional area. The furnace hearth area has remained practically unchanged over its entire history. The paper concludes that there is still more potential to be drawn from the process and MHD intends to sustain raw material input at a new level of 240 000 tonnes/year. However, this rate will have to be achieved under the imposition of more stringent environmental and product quality standards than ever before.

Jan 1, 1993

Previous published papers by Fraser (1), Hey (2), and Stillwell (3), have given respectively, details of:-1. The practice in the pilot plant operated at Zeehan for the treatment of ores from the Rosebery field.2. The design, based largely on the experience gained at Zeehan, of the concentrator built at Rosebery.3. The nature of the orebodies of the zinc-lead lode at Rosebery.Changes and developments, at the Rosebery concentrator, since operations commenced, are now described with particular reference to recent practice.Three concentrates are produced, viz.: a copper, a lead, and a zinc concentrate. The current flow-sheet is shown in Fig. 1. Typical concentrate assays are...THE OREThe ore treated is derived from the Rosebery and Hercules Mines and is, milled in the ratio of, approximately, two parts of the former to one of the latter. The ores from the two mines may be considered as being similar in general character, although the Rosebery ore contains more pyrite. It is from this mine that any increased tonnage is expected. The ore is a mass of fine-grained, intimately associated sulphides, with practically no coarse...

Jan 1, 1949

By Klaus Pöllath

This paper describes mitigating measures and the design of compensation grouting which will be executed from deep shafts of the Amsterdam North/South Metro line project. Due to the specific conditions for TBM-tunnelling in Amsterdam (historical buildings on pile foundations near the tunnel and soft soils with high groundwater levels) tunnel construction necessitates mitigating measures, such as compensation grouting or soil freezing. Züblin developed a special shaft construction method for critical distances to buildings. For the compensation grouting Züblin developed a new software tool, called SOFIA, which controls and visualizes and thus optimizes the entire injection process. This tool significantly increases the efficiency of the injection works while reducing the geotechnical risks.

Jan 1, 2006