Search Documents

By Duck Jae Lee, Kwan Ho Kim, Ji Whan Ahn

"In Korea, reutilization of constructions waste is gaining an increasing attention as generation of construction waste is projected to increase continuously. In current practices, the concrete waste is simply crushed and used as a low application such as paving, back filling, etc. In this study, a new process was developed comprising of heat pretreatment, autogenous milling, and density separation for complete reutilization of concrete waste. Firstly, the concrete waste was crushed using autogenous milling. The coarse size fractions from autogenous milling have a density of 2.5g/cm3 and a water absorption ration 3.0%, which meet the specification of the first class of KS F 2573. The fine size fractions were further separated using a hindered-settling column into two products 1) underflow, 2) overflow. The underflow sample was a high quality fine recycled aggregate which can be used for concrete making, and the overflow sample was an enriched cement material can be also used for CO2 sequestration by mineral carbonation. Introduction Kwan Ho Kim1, Ji Whan Ahn2, Duck Jae Lee1, Hee Chan Cho1 Recently, the importance of resource recycling is gaining a greater attention due to the increasing price of natural resource. Recycling is beneficial for not only the management of waste, but also the reducing of consumption of natural resources and huge energy consumption to treat of natural resource. The construction and demolition waste comprises the major industrial waste generated in Korea. It increased to 54 million tons in 2004, and is projected to increase to over 300 million tons in 2020, as many buildings reach the end of their 30 years life. Among total waste, the proportion of concrete waste was about 30% in Korea. Due to its large volume, recycling of concrete waste is the most important aspect of the waste management. In the current practices, the concrete waste is simply crushed and used as a recycled aggregate. The recycled aggregate has a low quality and most of them are down cycled for usage as paving material, back-filling material, concrete bricks, etc. It cannot be reused for replacement of natural aggregates because cement mortar is not separated perfectly from aggregates. These kinds of recycled aggregates tent to be weaker, more porous and have a higher value of water absorption. When these aggregates are used in concrete making, there are problems of higher total water demand, low compressive strength and durability [1-5]. And recycled fine aggregate is not almost recycled due to its low quality. In this study, a new processing circuit is developed to produce not only highquality recycled coarse aggregates but also fine aggregates and cement material from concrete waste."

Jan 1, 2008

By Martin J. Hansel, Jan Bäckström

Starting from historic perspectives on converting at the Rönnskär Smelter, the continuous developments of refractory practice is described. In the development the joint efforts of operators and suppliers of refractory have lead to significant achievements. This paper comprises the development of the converting process and the refractory lining as well as future prospects regarding operation and refractory lining design, especially in the face of equipment and raw material availability. 81

Jan 1, 2009

By Mao Chen, Baojun Zhao, Zhixiang Cui, Leonel Contreras

Viscosity is one of the important physiochemical properties of metallurgical slags which is important for slag tapping, metal loss in slag, freeze lining and fluid dynamics. High temperature viscosity measurements are time- and cost-consuming and the number of experiments is limited. Viscosity model is an effective way to predict the viscosities of the complex slags at high temperature. However, a reliable viscosity model can only be developed on the base of accurate experimental data. A unique high-temperature viscosity measurement apparatus developed at The University of Queensland enabled accurate viscosity data to be measured for the “FeO”-SiO2-CaO-MgO-Al2O3 system in equilibrium with Fe. An accurate viscosity model has been developed based on Eyring’s theory and extensive viscosity measurements. The viscosities of copper smelting, converting and cleaning slags over a wide range of compositions and temperatures can be predicted and applied in the process control.

Jan 1, 2016

By S. Orangi

A representative sample of ramming paste from a peripheral seam in an aluminium electrolysis cell was taken in order to develop a process to fabricate ramming paste samples in the laboratory. To this end, paste material was compacted in multilayers in a mould designed to be representative of peripheral seams in Alcoa's smelters. The density distribution in the representative sample was measured ranging from 1.51-1.76 g/cm3. The density range obtained by the proposed methodology in laboratory is 1.47-1.77 g/cm3. The results demonstrate that the proposed fabrication method adequately duplicates paste density from the cell for both one and two layer compaction. Finally, preliminary results related to the compressive strength and Young's modulus of laboratory samples were obtained at various temperatures and are presented in this paper.

Jan 1, 2011

By R. E. Ricksecker, W. M. Baldwin, R. McC. Baker

INTRODUCTION THE development of residual stress in strip during rolling has not been systematically studied. A few scattered papers1-3 mention the existence of residual stresses in rolled strip or touch upon some of their consequences,4 but there is no report of experimental studies in the literature describing the effect of roll diameter, strip thickness, reduction per pass, metal or metal temper on the magnitude of residual stresses developed in strip. A knowledge of the effect of these factors is of utmost importance since the present trend in some mills to roll thicker castings brings the rolling operation directly into that set of conditions which, as will be brought out in the present paper, can develop residual stresses of a high order of magnitude. Fundamentally, residual stresses are developed when a metal is inhomogeneously unloaded from a plastic stress state. A quantitative treatment of the problem requires a reasonably complete understanding of both the plastic stress state existing in the metal during deformation and the elastic stress state that would exist in the metal if the metal deformed as a perfectly elastic body. Our knowledge of either state during rolling is so meager that we can make no more than certain limited predictions. The external stress state* operating between the roll and the metal consists of compressive stresses acting almost perpendicularly to the strip surface but vary [ ] ing in intensity both across the width of the strip and along the length of contact between the roll and the strip. An example of such a stress distribution is shown in Fig I. The nature of the internal stress state, produced by this distribution, is not known. Various investigators,5-7 however, have felt that a qualitative similarity must exist between the internal stress state so produced and that produced in a wide strip that is compressed between two flat-nosed punches. In the latter case the external stress state is represented by a uniformly distributed compressive stress acting perpendicularly over the face of the tool. The elastic internal stress state in this case is complex-the principal stresses showing

Jan 1, 1948

By Mohamed Ahmed, A. Kawy

"Smelting of scrap copper and residual anodes and cathodes carried out in a reverberatory type furnace. In this, deoxidation process is carried out by wood, which acts as a resource of reduction gases such carbon monoxide, hydrogen and methane. Use of wood causes the formation of soot pollutants and efficiency of oxygen removal from copper is low leading to added costs in removing contaminants. This expensive problem was solved by using of reformed natural gas as a source of reduction gases (CO+ H2).IntroductionThree reverberatory furnaces were used for smelting of scrap copper and residual anodes and cathodes. Each furnace had a 7tpd capacity and was operated at 1183 °C.In this furnace, Step1-compressed air supplied by tubes from the side of the furnace to remove sulfur from copper matte by oxidation .The copper is also oxidized to copper oxide .[1]Step 2- copper from matte is deoxidized by a reductant. Typically deoxidation process is carried out using wood as a resource of carbon monoxide, hydrogen and methane which are the reduction gases. Use of wood causes the following:1- Forms soot pollutants2- Oxygen removal efficiency from copper is low; more contamination in copper matte increased energy in deoxidation3-the process is highly expensive.In the recent trends, this problem has been solved by using reformed natural gas as a source of reduction gases (CO+ H) .This results in 1-Reduced pollution during smelting.2- High efficiency in the removal of oxygen from copper to produce oxygen free copper. The surface of copper produced from this method is smooth which helps in forming and machining.3- Low cost and natural gas is more readily available in Egypt than wood."

Jan 1, 2010

By Sean C. Farrell

In underground mining and tunneling, machine design is predominantly dictated by mine conditions and individual customer desires. In partnership with Australian companies WDS Limited and Cram Fluid Power, the engineering department of J.H. Fletcher & Company was tasked to design and manufacture roof bolting modules to be mounted off both sides of a roadheader, providing in-cycle bolting. The objective was to produce a boom and bolt module that would allow an operator to bolt from a remote location, eliminating the need for miner to work in unsupported ground. The bolt module needed to operate in front of the cutting boom, but retract to a parked position out of the way during the cutting cycle. Due to Australian electrical approval requirements, it was desirable to design the module with minimal use of electrical controls. The need for multiple, complex, drill steel and bolt handling steps led to the need for a custom hydraulics package to automate several of the movements. The result of the design is dual drill and bolt modules mounted to a multistage boom with over 24 feet (7.31 m) of extension. Each unit rotates and tilts to meet the bolt pattern requirements in conjunction with the stow and load requirements. The bolt module builds on previous designs incorporating a modular assembly with each sub-component designed to be replaceable and adjustable independently from other machine components. Each major component is painted a different color to help the operator make the connection visually from the module to the operator?s control valves. Hydraulic package valves were designed to automatically control several of the sub-components during the drill cycle, reducing the number of steps a drill operator would, otherwise, have to do manually. This design removes the operator from working in unsupported roof and away from other inherent hazards, putting them at a safe distance on the operator?s platform. The cutting and bolting equipment has been combined into one machine, which is advantageous in single entry drifts because there is no need to place change equipment. The hydraulic package valves eliminate the need for any electronics, thus avoiding any electrical regulations with respect to the controls. The addition of these modules to the roadheading machine increases miner safety and streamlines production while meeting the ground control support requirements.

Jan 1, 2014

By E. Eccleston

The ConRoast process for the production of platinum group metals involves the use of a fluidized bed reactor for the removal of sulphur from ore concentrates by roasting prior to smelting in a DC-arc furnace. Test work was carried out in 2007 at Hazen Research in Golden, Colorado to provide the data necessary for a commercial roaster to be designed by Technip. This paper discusses the rationale behind the test work, the goals for calcine composition to be used as smelting furnace feed, the results of various roaster operating parameters in terms of calcine composition (particularly residual sulphur and the fate of trace elements), and the impact of the results in terms of a commercial roaster design.

Jan 1, 2009

By Harada M, Katsuta S

In order to shorten the time taken to com- plete shield tunnel excavation work, reduce labor costs and to improve safety, an automatic assembly robot system for the segments used has been developed. It was developed in the three years from 1982 until 1984. An experimental assembly system for concrete segments (outer diameter:.3.55m) has been thoroughly tested to confirm that these segments can be fed and assembled automatically (Fig. 1, 2). This report outlines the robot which will be put into practical use in the near future. The robot senses the position of already assem- bled segments by means of position sensors, controls the position and the attitude of the segment to be assembled to allow bolt hole positioning, and completes the automatic assembly of a se;nent by automatically tighten- ing bolts. The six segments which make up one ring can be automatically assembled in about 25 minutes.

Jan 1, 1987

By G. J. S. Govett

Dwindling near-surface mineral reserves emphasize the need for the development of exploration techniques capable of greater depth penetration; geochemical techniques tradition- ally have been restricted to the search for deposits having at least a sub-outcrop expression. Rock geochemical techniques developed in Cyprus in 1967-1968 recognized anomalous conditions in volcanic rocks up to one mile from an ore de- posit. Research by the Exploration Geochemistry Group at the University of New Brunswick has shown that some massive sulphide deposits in New Brunswick have well-defined halos of major, minor, and trace elements in the host rocks extending up to 1,200 metres (4,000 feet) laterally along the same stratigraphic horizon, and up to 450 metres (1,500 feet) vertically in hanging wall rocks which apparently post-date mineralization; well-defined halos have also been found in foot- wall rocks. Some of these halos are readily identified as individual elements or as element pairs; others are so subtle as to be recognizable only through computer-calculated multivariate analysis. Research continues to extend the dimension of rock geochemical halos for regional exploration and for identification of more restrictive anomalous conditions which may closely define the location and extent of buried sulphide deposits.

Jan 1, 1975

By P. K. Kaiser, C. Mackay

A circular shaft with a diameter of 6m was excavated by the conventional drilling and blasting method to a depth of 235m through 60m of glacial till, 1 Om of water bearing basal sand, 1 1 Om of clay shale (Bearpaw Formation) and finally a strata of coal, mudstone, siltstone and sandstone (Oldman Formation). The lined shaft was instrumented at three levels by multipoint extensometers to determine the displacement field near the shaft bottom, embedment strain gauges to measure the strains in the liner and IRAD-stress change gauges to observe the radial and tangential stress changes in the rock mass. The data from these gauges were used to determine the in situ stress field. An attempt to measure in situ stresses by overcoring was also made at a higher elevation. The performance of the shaft and its support was then evaluated by use of the "Convergence-Confinement Method". For this purpose the measurements of stress changes and displacements were combined to determine by extrapolation the displacements ahead of the shaft and after the liner installation. The convergence curves calculated in this fashion were then used to evaluate the performance of the cast-in-place concrete liner and of an alternate shotcrete shaft support system.

Jan 1, 1983

By Y H. Zhu, X X. Tang, Y C. Yin, M L. Xing

Based on the stiffness theory, the stiffness difference and energy supply of surrounding rocks are important inducing factors for strain burst. However, due to the lack of multi-level low stiffness testing machine, there are few experimental studies on rock failure mechanisms under the influence of loading stiffness. This paper introduced a self-developed rock testing system with changeable stiffness. The main testing machine of this system is a combined structure of inner and outer frame. The change in the loading stiffness is achieved by using a stiffness servo control system to control the energy accumulation in the inner frame. The tests of the sandstone specimens under three different loading stiffnesses in the testing system showed that the loading stiffness did not significantly affect either the uniaxial compressive strength or the Young’s modulus of the rock. However, the post-peak stress-strain curve of the rock became smoother and steeper when the loading stiffness was decreased, and the stress drop rate increased. It is shown that the stress drop rate had a power function correlation with the loading stiffness. After the peak load, the inner frame of the testing system rebounded several times at high speeds. The magnitude of the instantaneous rebound speed and the rebound duration increased with the decrease of loading stiffness. Both the mean rebound velocity and the total rebound deformation had power function correlations with the loading stiffness. The loading stiffness has limited effect on the energy storage and energy dissipation characteristics of the specimen, while the released energy of the testing machine increases as the loading stiffness decreases, which is the key factor affecting the failure mode of the specimen. According to the test results, a rock burst mechanical model considering the stiffness is established, and the energy supply mechanism of rock burst is quantitatively explained.

Nov 29, 2022

By B. Singh

The use of wire ropes has already been tried in a few countries for roof support In mines. But the use of scrap wire ropes, as a method of support on extensive scale has not been reported from anywhere except India. Extensive trials using freshly discarded wire ropes for roof support were undertaken both in the laboratory and field. In laboratory, model beams supported with different reinforcing techniques were tested to evaluate their comparative load bearing capacity vis-a-vis reinforcing factor. Among all the tests, the model supported with wire rope system at 60° angle in combination with two supplementary vertical bolts offered the best result 1.e. about 95% reinforcement. It also accepted post fracture loading of the beam. In statical analysis too, the best result could be obtained with the rope installed across the gallery at 60° angle. All these findings are in conformity with the field observations obtained during roof stitching practices in coal mines. Of late, roof stitching, an effective and economical method of roof support developed at CMRS, India in 1972, found wide application in over 200 coal mines. In this method, a freshly discarded wire rope is grouted across a gallery in two inclined drill holes supplemented with two middle vertical roof bolts at every 1.0 to 1.2 m interval along the gallery. It is tensioned against the roof using wooden sleepers and thus, the whole system functions like a roof truss.

Jan 1, 1990

By Jeffrey Shawn Peterson

Among underground coal miners, hearing loss remains one of the most common occupational illnesses. In response, the National Institute for Occupational Safety and Health (NIOSH) conducts research to reduce the noise emission of various underground coal mining equipment, an example of which is a roof bolting machine (RBM). After the removal of coal or rock, the remaining strata may be subject to fall, either from overhead (the roof) or from the side (the rib). One method used in underground coal-mines to prevent failures requires the installation of roof bolts. The roof bolting machine operator trams the machine to the required location, drills a hole into the strata, and then installs a roof bolt, supporting the roof or the rib, as the case may be. Field studies support the premise that, on average, drilling noise is the loudest noise that a roof bolting machine operator would be exposed to and contributes significantly to the operators? noise exposure. NIOSH has determined that the drill steel radiates a significant amount of noise during drilling. NIOSH is developing bit and chuck isolators to reduce vibration, and thus noise radiation of the drill steel, with the longer-term goal of reducing roof bolting machine operator noise exposure. Laboratory testing has shown that operator ear sound pressure levels may be reduced by 3 to 7 dB(A), depending upon the test configuration and drilling media.

Jan 1, 2009

By K. C. Liddell, B. Dou

"In producing multilayer films for magnetic data storage applications, the interfacial roughness must be controlled in order to obtain high quality materials with reproducible properties. The present understanding of the effect of roughness on multilayer properties such as magnetoresistance is sketchy, particularly for electrodeposited films. In this study, quantitative atomic force microscopy was used to characterize surface morphology before and after Ni films of varying thickness were deposited on Cu cathodes. A multinuclear multilayer growth mechanism is supported by both the deposition conditions and the AFM images, and a multinuclear multilayer model gave a satisfactory fit to measurements of the density of peaks on ultrathin Ni films between 0 and 8 nm thick.Alloys consisting of alternating ferro-and paramagnetic layers have begun to replace Permalloy in the sensing elements of magnetic hard drives. The operating principle of the new read heads is giant magnetoresistance (GMR), and they are smaller and more sensitive than previous inductive heads (1). Experimental studies on sputtered multilayers have emphasized the role of layer thickness and interlayer roughness in determining the presence and size of the GMR effect (e.g., 2,3,4,5,6). However, roughness in electrodeposited multilayers has rarely been measured, even though read heads are likely to continue to be made by this process for some time to come. Cu/Ni can be considered a model system for understanding processing-microstructure-property relationships in electrodeposited multilayers and is the most widely investigated of all such systems (e.g., 7,8,9,10,11,12). Nevertheless, the roughness of the interfaces in Cu/Ni electrodeposits has not been systematically characterized by quantitative techniques, and in all studies reported so far, the total deposit thicknesses were considerably greater than the 10 nm needed for most sensor applications (1). The thinnest such films were about 50 nm (7)."

Jan 1, 1998

By S C. Dominy

The Bendigo Goldfield is located in the state of Victoria, Australia, and is one of a number of quartz-reef fields that make up the greater Central Victorian Goldfield. At Bendigo gold particles are characterised by their very coarse nature, ranging from below 100 to over 10 000 ¦m in size. Some 60 per cent of the gold occurs in particles greater than 1000 ¦m in size. This characteristic ensures that the mineralisation is very challenging to both sample and evaluate. Diamond drilling provides a measure of geological structure, but is a poor measure of in situ grade, understating it by up to 75 per cent. Drilling combined with on-reef development, bulk sampling and geological interpretation has been used to define Indicated Mineral Resources. For grade control, a balance had to be sought between sample representivity, cost, turn around time and practicality. Sampling of extreme nugget effect deposits generally requires the use of bulk sampling in order to be representative. However, the cost and turn around time is significant. As a result, a 50 kg micro-bulk sampling system has been introduced that attempts to overcome these problems by providing a fast, practical method that can discriminate between ore and waste. As the mine passes into production, grade control will increasingly become dependent upon geological data collection and interpretation.

Jan 1, 2005

By S. Asokan, D. Rathod, Ch. V. G. K. Murty

Tata Steel, a steel arm of Tata Group, is Asia's first and India's largest integrated private sector steel company. Tata Steel’s turnover in fiscal 2004-05 was nearly US$ 3.25 billion. As part of its vision to grow in related industries, Tata Steel is poised to enter the Titania businesses in the Indian state of Tamil Nadu. The Titania project will involve mining, separation of ilmenite & other co-minerals, beneficiation of ilmenite to synthetic Rutile and further maximum value addition to Titanium metal. This paper outlines the journey from the concept to current findings of the Bankable Feasibility Study in developing Sattankulam Heavy Mineral Sands Deposits in the State of Tamil Nadu, India by Tata Steel.

Jan 1, 2005

By Jorge Alvarez

In a large-scale open-pit mining operation, continuous efforts are made to control damage to the slope walls. An essential tool in this effort is determining the PPVc (critical peak particle velocity) in areas of interest. By knowing this value and generating criteria, drilling and blasting designs can be established to reduce vibrations that affect wall construction. It is crucial to understand that the PPVc changes as different mining phases develop, especially due to exploitation on the benches, which leads to vertical inherited damage. Therefore, it is imperative to regularly update the PPVc based on field tests that provide accurate data. With this information, vibration damage criteria can be established, and drilling and blasting techniques can be designed to minimize the impact on the remaining rock mass. This document presents a methodology for generating scaled criteria that best represent the reality of the rock mass.

Jan 21, 2025

By Kota Nakashima

Residues from titanium smelting tend to contain scandium. The scandiumis discarded because no suitable process exists for its recovery from the residue. Valuable-metal recovery from discharged residue is critical for environmental conservation and to achieve a sustainable society. Since 2015, JXNippon Mining&Metals has been developing a process for scandium recovery from the residue of a titaniumsmelting process. The process consists of the following steps: scandium concentrating by classification or neutralization, selective scandium leaching, impurity removal by neutralization, solvent extraction of scandium by using D2EHPA, purification, and roasting. We optimized the above steps to achieve an effective process to obtain scandium oxide (Sc2O3). In this paper, we introduce results from the bench-scale test of the scandium recovery flowsheet developed by JX Nippon Mining & Metals.

By R Adamian, F. T. Da Silva, D. H. Gameiro

Schytill and Geldart diagrams were developed for the TiO2-C-Cl2 system at 1 073 and 1 273 K, so as to define the hypothetical relations between particle sizes and chlorine velocity for simultaneous fluidisation of mixtures of anatase concentrate and charcoal for carbochlorination. It was concluded that the operating limits on chlorine gas velocity will be controlled by the behaviour of the reducing agent, mainly because of its lower density. An increase in temperature from 1 073 to 1 273 K will have only a small influence on the fluid-dynamic behaviour of the mixture. For bubble fluidisation, the maximum sizes 0.413-0.478 mm for anatase and 0.529-0.611 mm for charcoal will be adequate. When the particle size distribution is large, fluidisation will be feasible only if conducted in two stages, otherwise the residence time of the small particles in the reactor will be very short. New diagrams will be needed for the gaseous chlorides in the second stage

Jun 21, 1905