Search Documents

By Chen Bingchen, Ma Shaojian

A new magnetic liner, with unique magnetic circuit and novel structure designs, was developed. It was characterized by light weight, low noise, as well as corrosive and abrasive resistance. The wear rate of the magnetic liner was one twentieth and one ninth those of the manganese-alloy steel and rubber ones respectively. The forming mechanism of the protective layer and that of influencing factors on magnetic liners were also investigated. The research results could not only instruct using magnetic liner, but also widen their application.

Jan 1, 1995

By A. Asadi

Subsidence phenomenon as an unwanted consequence of underground mining can cause problems for environment and surface structures in mine area. Surface subsidence prediction for inclined and steep seams has been given less attention than horizontal seams due to the difficulties involved in the extraction of such coal-seams. This paper introduces a new profile function method for prediction of surface subsidence due to inclined coal-seam mining. The results of calculation with the new function indicate that the predicted value has good agreement with the measured data. Keywords: subsidence; coalmining; caving mining methods; longwall mining; profile function.

Jan 1, 2005

By H. Tudeshki

A great amount of aggregate is utilized in civil engineering applications such as road construction, railway infrastructure, concrete production, etc. Igneous rocks are the preferred raw material due to their high strength and abrasion resistance. Rock quality assurance is a key factor and has great influence on the quality of constructions in civil engineering. One of the major problems encountered by both the producers and users of igneous aggregate rock is the fact that, with the passage of time, some specific rocks lose their strength, up to a complete loss of structure, i.e. disintegrate and degrade. This phenomenon has a great influence on the quality, strength and durability of aggregates. In the last decades, different methods and procedures such as the glycol test, the methylene blue dye test, as well as the Los Angeles test, have been introduced to distinguish rock properties, and to identify these problems. However, as these wet-chemical methods are time consuming, hard to perform, only to be applied to hand-piece samples, requiring special laboratory equipments, and are only possible to be accomplished under laboratory conditions, their application has always been severely limited. To address this widespread quality management problem of the quarry industry, a relatively quick, easy and user-friendly approach is necessary. It calls for a systematic solution with a device that can simply be used in the day-to-day routine of a mine for quality control of the quarry´s daily production. Our research is concentrated on developing a systematic method for early recognition and diagnosis of rock quality, in order to control and manage the quality of the quarry production in advance. Our new approach is based on two rock parameters: magnetic susceptibility and loss on ignition. The measurement of these parameters provides reliable information on the quality of the rock and allows the quality control process to be accomplished and performed at the borehole location. Our new approach has been assessed through extensive field and laboratory studies and has been implemented on the drill-cuttings of a basaltic andesite quarry. The results of the experiments are discussed in detail, including their impact on increasing resources and environmental protection.

Aug 1, 2013

By H. Tudeshki, A. Tayebi

"The large extent of global production and consumption of aggregates from quarries, grabs one´s attention and makes its substantial and essential standpoint in the world today pretty clear. A great amount of aggregates is utilized in civil engineering applications such as road construction, railway industry, concrete production, etc. Considering this fact that igneous rocks display a higher strength and abrasion resistance, this type of rock is preferred in the field of civil engineering. For all these applications, rock quality assurance is a key factor and certainly unavoidable, and it has great influence on the quality of constructions in civil engineering. One of the major problems encountered by both the producers and users of igneous rock is the fact that, with the passage of time, some specific rocks lose their strength, up to a complete loss of structure or in other words, their disintegration and degradation. In the last decades, different methods and procedures such as Glycol test, methylene blue dye test, as well as the Los Angeles test have been introduced to distinguish these rock properties, and to identify these problems. However, as these methods are time consuming, hard to perform, only to be applied to hand-piece samples, requiring special laboratory equipments, and only possible to be accomplished under laboratory conditions, their application has always been limited to some specific cases, and they are neither recommendable nor advantageous. In addition, these methods provide partially different results for the same rock. To address this widespread quality management problem of the quarry industry, a relatively quick, easy and user-friendly approach is necessary. It calls for a systematic solution with a device that can simply be used day to day in a mine for quality control of the quarry´s daily production. This scientific research is concentrated on developing a systematic method for early recognition and diagnosis of rock quality, in order to control and manage the quality of the quarry production in advance. This method was developed, based on the procedure of the magnetic susceptibility measurement. The obtained values can lead to valuable information regarding the quality of the rock and allows the quality control process to be accomplished and performed at the borehole location. This approach has been assessed through extensive field and laboratory studies. A detailed and comprehensive discussion will be made on the results of the experiments. The advantages and impacts of the application of this method, on increasing the reserves and environmental protection are also discussed."

Jan 1, 2011

By F. C. Appleyard

A couple of miles southwest of the town of Saltville in the western tip of Virginia is a little village called Plasterco. Gypsum has been produced in this area since about the year 1815, being originally found as small outcrops at the surface. Production in the early days was very small, and the use of the mineral was limited to that of "land plaster" or ground gypsum which was spread on the land to sweeten the soil. In the late 1800's, a small calcining plant was constructed and the production of gypsum plaster began. About this same time, the surface rock was depleted and it became necessary to begin underground mining operations in order to maintain a continuous supply of raw material. The United States Gypsum Company became interested in this property in 1909, and has operated there ever since, having enlarged the calcining mill and built a plant for the manufacture of gypsum wall-board in the middle 1920's. Production of gypsum continues from underground' mining operations, and the present mine at Plasterco is now about 1,000 feet below the surface, making it the deepest gypsum mine' in the world.

Jan 1, 1965

By P. H. S. W. Kulatilake, T. Hudaverdi, C. Kuzu

Prediction of blast fragmentation plays a key role for overall productivity of mines. In this study, a new multivariate analysis procedure for prediction of blast fragmentation is presented. Several blasts performed in various mines and rock formations worldwide were brought together and evaluated. An extensive blast database was created. Blast design parameters, the modulus of elasticity and in-situ block size were considered to perform multivariate analysis. A complete multivariate analysis procedure was applied in three steps. First, a hierarchical cluster analysis was used to separate the blast data into different groups of similarity. Two different groups were formed based on the elasticity modulus values. In the second step, group memberships were checked by discriminant analysis. The dominant parameters of the occurrence of the groups were determined. Also, discriminant analysis was used to determine the group membership of the respective blasts. As the last step, the multivariate regression analysis was applied to develop prediction equations for estimation of the mean particle size of muckpiles. Two different prediction equations were developed based on the rock stiffness. Validation of the proposed equations on various mines was performed. Prediction capability of the proposed models was found to be strong. The models are not complex and are suitable for practical use at mines.

Jan 1, 2011

By I. Bhattacherya

Over the last three decades, the mining industry has been moving towards underground mechanized mining methods and the number of load haul dump (LHD) vehicles utilized has increased. The growth of mechanization and automation has benefited both workers and mining companies. However, due to the design constraints with LHD vehicles and the limitations of the operating environment, restrictions to operator visibility has contributed to a number of accidents, including fatal injuries. Past researchers have used the light filament technique to collect obscuration zones around mobile equipment and have produced 2D visibility charts (shadow diagrams) of this information. The light filament method involves manually collecting visibility data, which results in errors and is time consuming, requiring around three hours to complete. This research utilizes a MENSI GS100 laser scanner along with 3D modelling software (3Dipsos) to collect and process operator visibility profiles for underground mobile equipment. Results from this test work indicate that a laser scanner can be successfully used to rapidly collect this data and utilize this information for improved mobile equipment design from a visibility perspective. Nomenclature FERIC Forest Engineering Research Institute of Canada ISO International Organization for Standardization JACK Software for digital human modelling and ergonomics LHD Load haul dump vehicle LOS Line of sight MASHA Mines and Aggregates Safety and Health Association (based in Ontario, Canada) PVD Polar visibility diagram SAMMIE3D human modelling computer aided ergonomics design system WSIB Workplace Safety and Insurance Board

Jan 1, 2006

By L. M. Cenegy

Introduction The formation of scale is common in gold ore processing plants. A working definition of such scale is: "A hard, tightly adhering deposit formed in place by the precipitation of calcium-bearing mineral compounds from water." The most common scale found in gold processing plants is calcium carbonate (CaCO3) although calcium sulfate (CaSO4) is occasionally a problem. The problem of scale in carbon strip circuits Carbon strip circuits present a particularly challenging scale inhibition problem. Many of the factors that tend to promote scaling are present in these systems. For example, carbon strip circuits are run at high temperatures and high pH levels and require long batch cycle times. Tortuous paths are encountered by the strip solution circulating through heat exchangers, pipes and elbows, causing transient pressure drops throughout the system. Severe conditions such as these cause the water to possess a high scaling potential and may lead to the breakdown of some of common types of scale inhibitors. Formation of scale Natural waters contain dissolved minerals and gases that promote scaling. One of the contained gases, carbon dioxide (CO2), is an important factor in scale deposition. Carbon dioxide dissolves in water to yield carbonic acid according to the following reaction: [CO2 + H2O - H2CO3 (carbonic acid)] Carbonic acid rapidly dissociates to yield bicarbonate and carbonate ions depending on the pH of the system: [H2CO3 -s H+ + HCO-3 (pH range 6-10) HCO3 -a H+ + COO (pH range > 9)] In gold cyanidation processes, lime is added to raise the pH of the mill solution to 10 or above to promote cyanidation of the gold and to eliminate the possibility of hydrogen cyanide (HCN) formation. Lime contributes both hydroxyl ions (OH--) and calcium ions (Ca++) to the solution. The normal scale forming reactions in mill water systems were described by Beasley (1973) as: [HCO-3 + OH -s C03 + H2O Ca++ + C03 -a CaCO3] Factor affecting scale deposition According to Linke's (1958) solubility tables, the solubility of calcium carbonate in carbon-dioxide free water is only 13 mg/dm3 (13 mg/L) at 25° C (77° F). Scale deposition occurs when the concentration of calcium and carbonate ions in the solution exceeds the solubility of calcium carbonate. This occurs, in most cases, when the water has undergone some chemical or physical change. Some typical changes that might occur that lead to scale deposition are discussed below. Temperature An increase in temperature can greatly increase the tendency to form calcium carbonate scale. Studies by Miller (1952) have indicated that calcium carbonate is less soluble at higher temperatures. Hence, high temperatures promote scaling. For this reason, scale is often noticed on heat exchangers, autoclaves and other high temperature surfaces. Pressure A decrease in pressure may lead to an increase in the tendency to form calcium carbonate scale. Fulford's (1967) work has shown that scale is more soluble at high pressures. Hence, scale is likely to be prevalent in pump suction lines, elbows, baffles and other areas that produce turbulence and subsequent pressure drops. Change in pH Calcium carbonate scale is pH dependent and tends to form more readily at high pH. Any event that causes an increase in pH, such as the introduction of lime or caustic, would tend to initiate scale formation. Since most gold recovery operations are run at a pH above 10, the tendency to form calcium carbonate scale is always great. The use of scale inhibitors to prevent calcium carbonate scale Many products are commercially available to inhibit the formation of calcium carbonate scale. Some of the more effective types include phosphonates, as well as acrylate and maleate-based polymers and copolymers. Many of these products function by means of threshold

Jan 1, 1992

By L. M. Cenegy

The formation of scale is common in gold ore processing plants. A working definition of scale, applicable to the various scaling conditions found in gold ore processing plants, would be: "a hard, tightly adhering deposit formed in place by the precipitation of calcium-bearing mineral compounds from water". The most common scale found in gold processing plants is calcium carbonate (CaCO3) although calcium sulfate (CaSO4) is occasionally a problem.

Jan 1, 1990

By Vince Caggiano

The newly developed Hilti OneStep roof bolt combines the standard 5-step anchoring process (i.e. drilling, transfer of drill steel, insertion of resin, insertion of rod and tightening) into one easy operation. It also replaces 4 items (drill head and steel, adhesive cartridge and anchor) for simplified material management. This paper describes its history of development, and bolt, bolt drilling and bolt resin specifications, experimental test results in Germany where it achieved a reduction of 36-42% in roof bolt cycle time and 25-30% improvement in gateroad development rate. In the U.S. coal mines, a time study showed that OneStep can save approximately 50 seconds in installation time per bolt.

Jan 1, 2005

By M. S. Shishvan, J. Sattarvand, R. S. H. Meij

Navigating miners during an evacuation using a smart evacuation technology can significantly decrease the evacuation time of an underground mine in case of an emergency. This paper presents a mathematical programming model to calculate the most efficient escape path for each miner as a critical component of the smart evacuation technology. In this model, the total evacuation distance of the crew is minimised and scenarios with blocked pathways, and stamina categories for the miners are simulated. It was found that all the tested scenarios are technically feasible. Using the feature that filters out blocked pathways has no downsides, as safer routes are calculated, and there is no penalty in the computation time. The paper also discusses the social and technical issues that need to be overcome before the algorithm can be implemented as an actual escape solution.

Sep 1, 2021

By J. D. Robertson

An in situ water sampling device has been developed to measure biologically-available or “labile” metals in natural waters and effluents. The active mechanism involves the use of a polyacrylamide gel layer to quantitatively control metal transfer to a trace-metal-adsorbing, gel-imbedded resin. Because the resin only adsorbs free metal ions (the gel sampler methodology is a kinetic speciation technique), and because metal bioavailability is related to the free-ion activity, the device provides a direct measure of the biological-availability of metals in the environment sampled. The prototype consists of a layer of ion-permeable polyacrylamide gel which separates the solution to be sampled from an ion exchange resin. Because approximately 90% of the polyacrylamide gel is water, mass transport through the gel is diffusion-controlled, and is therefore well defined. Metal ions are rapidly bound by the resin, creating a steep concentration gradient in the gel. The amount of labile trace metal that accumulates on the resin can be related directly to the concentration of the metal in solution, the exposure time and the molecular diffusion coefficient of the labile species. In addition, the passive nature of this device affords it the potential to address many of the limitations presented by conventional sampling methods, such as sample contamination introduced during collection or filtration and changes in trace metal speciation prior to analysis. Laboratory studies and limited field trials indicate that the sampler behaves as anticipated and illustrate that biologically- available metal concentrations in many environments are a small fraction of the total concentrations and often significantly less than the dissolved concentration. The implications of this on regulatory criteria are discussed. Additional field trials and correlation with bioassays are currently underway.

Jan 1, 2000

By C. Newman, N. Schaefer

"As underground mining continues to operate at deeper depths and in more complex geologic and geometric conditions, there has been an increased demand for mine designs to better reflect site-specific conditions, measurements, and observations with respect to ground control safety and stability. During the past 20 years, the National Institute for Occupational Safety and Health (NIOSH) has developed, validated and distributed a number of free software packages (ALPS, ARMPS, AMSS, ARBS, etc.) specifically aimed at providing the industry with ground control design tools for the evaluation of underground stability in coal mines. While these programs were initially developed as stand-alone software packages where all data reside on an individual or workgroup computer, modern day web applications have begun to migrate toward a “multiple-tier” architecture, allowing multiple users to access an application by means of an Internet connection.This article introduces a new Web-based platform for ground control software applications, webGroundControl (webGC). webGC provides users with a platform through which one can access NIOSH and other ground control design software utilizing a Webbased, multiple-tier architecture. This provides users with easy access to ground control designs, the ability to perform on-demand calculations, as well as increase online collaboration between operational personnel and engineers through a web server. The basic framework and, more specifically, the user-interface of webGC are defined and outlined within this paper. It is expected that the mining industry will rapidly embrace this new product and webGroundControl will be a new paradigm for mining engineering computer applications. Platform architectureAs Web-based computing technologies continue to advance and cloud computing gains momentum, web-based platforms for software applications are growing in popularity across all industries due to ease of product accessibility and distribution as well as data security. With the expansion of Internet connectivity on the surface and underground, there is an industry need to develop Internet-based applications for mine and ground control design (Barczak et al., 2016). Cloud-based products are already available for many industries and are slowly being developed for the mining and geotechnical industry. A notable example is the drillysis package, which is a cloud-based borehole logging database (Geosysta, 2017) or the Dynonobel package for on the fly blasting calculations (Dyno Nobel, 2013)."

Jan 10, 2017

By Rocky (Yaokun) Wu

Rock burst is one of the biggest challenges to ground control in the mining industry. With increasing mining depth and mining scale, there are more and more industry requirements on yielding rock support. Since 2008, Jennmar has been conducting large scale research and development works to develop a technically reliable and cost effective yielding rock bolt. This paper introduces a new yielding rock support - Yield-Lok bolt. The bolt is characterized by the designed yielding ability to produce 150 ~ 250 mm of deflection at 8 ~ 10 metric tons (Mt) loads for every 16.4kJ energy input. Its performance characteristics are consistent through multiple and varying amplitude of impacts. In this paper, the design criteria of the bolt and the principle of performance are described, the dynamic testing results are discussed; and the features and application of the bolt are presented.

Oct 1, 2010

By Julie Shang, Tim Evans, Michael McDonald, Yu Guo, Bingfeng Xue

Effective chemical grouting represents a technical and economic solution to many challenges related to soil stabilization and blocking the flow of water. Chemical grouts are facing increasing demands in durability, environmental impact and value. To better meet these challenges, a novel and cost effective process was developed to produce a sodium silicate that increases the ratio (i.e. silica to alkali) beyond what has been used in traditional silicate-based grouts. The move to a lower sodium form of silicate was anticipated to have two desirable performance enhancements; a reduction in leachable sodium and improvement in the durability of the silicate grout. An in-depth study was performed at the University of Western Ontario Geotechnical Research Centre to quantify improvement in durability as well as other performance properties such as compressive strength. The study began by first modelling the gelation time and reaction kinetics of the high ratio sodium silicate over a range of silicate concentrations using two different setting agents as well as with/without a hardener. As expected, reducing the level of sodium produced a much more water resistant grout. These same formulations also showed a four order magnitude reduction in permeability. Somewhat surprising, test results showed the higher ratio silicate having much higher compressive strength. At the time of this abstract, the high ratio silicate was moving to the trial stage for geotechnical applications while the petroleum industry was further along with several successful field trials for water blocking as well as cement remediation. This paper will review the chemistry, testing and features of this next generation form of sodium silicate. Introduction Sodium silicate based grouts have been used for decades for soil stabilization and water control. Over the years, several silicate-based systems have been tailored for specific application conditions to maximize performance and reduce cost. Past research has also focused on the selection of setting agents and hardeners for silicate grouts. A constant in the development effort has been the grade of sodium silicate. The vast majority of chemical grouts have been formulated using a ~3.2 ratio sodium silicate. As a very brief overview on the meaning of “ratio” and why it is so important to performance properties. The ratio describes the proportion of sand to alkali or SiO2:Na2O used to make different grades of sodium silicate. Comparing a 2.2 ratio to a 3.2 ratio, it is easier to polymerize and set the 3.2 ratio. Upon setting and forming a silica gel, the system has higher compressive strength values and improved durability with a reduced level of syneresis (i.e. shrinkage). This leads to the question if 3.2 is better than 2.2 why not go to 4.2 or higher?

Jan 1, 2018

By Y D. Jeon, K S. Kim, C-H Eom, C M. Yoon

The carbon neutrality continues to require reduction of carbon usage in ironmaking and steelmaking processes. Specially, it is expected that the hot metal ratio (HMR) in the steelmaking process should be reduced essentially. Unfortunately, the reduction of the HMR in converter can bring about poor environment for nitrogen removal from molten Fe. From this situation, nitrogen prediction model has been developed to understand the fundamental of behaviour of nitrogen and quantitatively interpret its content changes in the converter process. Thermodynamic and kinetic approaches were improved based on existing mathematical model and attempted to predict nitrogen content in realtime by combining process data. In present study, heat supply from the oxidation (mainly carbon and silicon) and CO evolution in the converter are considered, and scrap melting due to the heat transfer from the molten Fe to the solid scrap charged in the converter also be considered.

Aug 21, 2024

By P. Sotiropoulos

In the framework of the Specific Programme: ?Promoting Competitive and Sustainable Growth? a detection system was designed and developed in order to provide an added value service beyond standard instrumentation. In the hydrocarbon industry it will be possible for the first time to detect in a pulse regime, two types of radiation emissions using a single device. This means that any saturation of hydrocarbons can be detected, irrespective of the degree of formation water mineralization, which is a major limitation on currently available neutron-gamma tools, where the formation water has a low mineralization.

Jan 1, 2006

By E. Petrakis, K. Komnitsas

The main objective of batch grinding modeling is the estimation of the product particle size distribution over time or specific energy input to the mill. So far, the developed analytical methods require often complicated calculations which are timeconsuming. Thus, more simple approaches that allow the reliable prediction of the complete product size distribution need to be developed. In the present paper, an approach, based on the population balance model (PBM), that reliably predicts the product size distribution is proposed. In order to enable this, the simplified form of the fundamental batch grinding equation was transformed into the well-known Rosin–Rammler (R-R) distribution, thus allowing the determination of the breakage rate for each grinding period. A time-dependent breakage rate framework was developed where the traditional linear theory of the PBM is considered a partial case. This approach allows the deviations from the linear theory to be categorized and the degree of the acceleration-deceleration of the breakage rate to be predicted. Modeling results were validated by laboratory grinding studies using two homogeneous materials, quartz and marble, and one heterogeneous, a limonitic laterite. The experimental data revealed that grinding exhibits non-first-order behavior and the degree of deviation from the linear theory depends on the tested material. The reliability of the proposed model was validated with the use of the distribution modulus n, the a value of the breakage rate parameter, and the optimum n values that minimize the sum of the differences between the experimental and estimated particle size distributions.

Feb 8, 2021

By C. A. Fleming, C. J. Ferron, I. Dymov

An oxidized gold/silver ore from Mexico has been evaluated at Lakefield Research in order to develop an economically viable treatment flowsheet for the recovery of gold and silver. Initial cyanidation test results indicated that at least 20 kg/t cyanide was required for maximum gold and silver extractions, due to high cyanide consumption by an oxidized zinc mineral present in the ore. A process was developed for the recovery and recirculation of the cyanide from the leach liquors. The proposed flowsheet included direct cyanidation, CCD and Merrill-Crowe, followed by precipitation of the zinc associated with cyanide with sodium sulphide and recycling of the regenerated cyanide liquor to the leach circuit. The process was demonstrated during a continuous pilot plant. A mill has been erected recently in Mexico and has been operating using this flowsheet.

Jan 1, 1997

By Eduardo Poltronieri Trés, Anderson Denadai Thomazini, Rodrigo Boyer Fernandes, Francisco de Assis Dutra Macedo, Gilvandro Bueno, Maycon Athayde, Rossano Augusto Pilon Nunes

The fundamental importance of comminution by high-pressure grinding roll (HPGR) technology to efficiently increase the particle surface area lies in lower energy and water consumptions for iron ore pellet feed production. This study compared the ball wet milling process with the innovative HPGR processing technology for hematite-goethite ores. Green-pellet balling and induration processes were simulated on the bench and pilot scales.