Search Documents

By J. Jacob

Diamondiferous linear beaches in Mining Area No. 1 have been the mainstay of Namdeb?s diamond production for more than 80 years. Most of the onshore beaches have been mined out, but in recent years mining has been extended offshore into the surf zone through a process of beach accretion. A total of 61.6 million carats has been produced from the gravel beaches since their discovery in 1928, and Mining Area No. 1 is considered to have great remaining potential from areas currently submerged under water. To date, the surf zone has remained largely unexplored due to the consistently strong winds, currents, and large waves which make access to this area extremely difficult. This paper describes the processes used in developing a practical methodology for exploration of the surf zone in a domain extending approximately 22 km long in a northwest?southeast direction and 0.3 km wide in a perpendicular direction adjacent to the current Mining Area No 1. The vigorous surf zone poses multiple technical challenges in terms of obtaining geological and diamond information. In order to access the area for sampling, a jack-up walking probe drill platform (PDP) with a 5-inch diameter reverse-circulation drill has been developed to carry out exploration drilling in the dynamic surf zone. The hydraulically driven platform has eight legs, each of which is 18 m long. Four of the legs are in fixed positions on the fore and aft sides of the platform. The other four moveable legs are fitted to sliding frames attached to the port and starboard sides of the platform. The sets of fixed and moveable legs can be raised and lowered by hydraulically powered jacking stations. By alternately lifting and lowering the sets of fixed and moveable legs in conjunction with the frames moving back and forth horizontally, a walking action is performed by the PDP. The platform can walk at a speed of 10?15 m/h, depending on weather and footwall conditions. Optimization of sampling for diamondiferous gravel occurrence in Mining Area No.1 was undertaken through creation of a virtual orebody on which different sample configurations were tested. The input data for the construction of a virtual orebody comprises a set of drilling data, collected from recently accreted areas directly adjacent to the 22 km × 0.3 km target domain. The input drilling data covers only 34% of the domain, and for the purpose of this study, a single realization is deemed to be sufficient. The texture obtained from using only the drilling data to construct a simulation did not make geological sense; hence it was necessary to make use of analog data in order to improve the simulation. The first analog data used consists of the gully patterns found in the metasedimentary Precambrian bedrock footwall. Gullies are, in general, gravel filled and it is fair to assume that gully patterns form a subset of the total gravel occurrence. Total gravel occurrence includes marine terraces (governed by sealevel stands) above bedrock peaks, together with gravel within gullies below bedrock peaks. The second analog ?data? introduced is through the use of ?expert interpretation?. The indicator drilling data is interpreted by expert opinion and the 2-dimensional result is hand-sketched, digitized, and then pixelated. The pixelated data set is then used as input for variogram calculation. This study cannot provide a single definite optimization result as the nature of the data does not permit this. The use of different validation approaches (conditioning data, where available; expert interpretation; and gully pattern data), however, can give a very good indication of how to balance sampling effort with de-risking aspects related to geological continuity. Work undertaken by sampling the simulation will give an assessment of the relative probabilities of determining gravel occurrence in the study area. This study showed that a 50 m × 400 m cross-configuration will be a good initial sample spacing for highlighting areas where gravel may be absent, and further infill drilling may be required. The relative efficiency of a 50 m × 400 m cross off-set sampling configuration has been demonstrated using a trumpet curve versus sampling effort when using kriging as the estimation method. Keywords sampling configuration, marine diamonds, orebody simulation.

Jan 1, 2014

By William. J. Birch, Catherine. E. Johnson, Robert Farnfield

Rocks and other materials can be characterized by their elastic properties. However, seismic velocities represent a more practical set of physical properties for seismic methods. Seismic velocities define the speed at which various elastic deformations propagate through different rock types. Seismic velocities for a given material can be expressed explicitly in terms of their elastic properties. It is widely accepted that the peak particle velocity and associated frequency of ground motion are important parameters for determining a safety criterion to minimise the potential for both damage to structures as well as nuisance to people. Whilst the key considerations are the blast design parameters, the seismic velocity is important as particle velocity is dependent in part on the powder factor [blasting ratio] which in turn is found to be dependent on the seismic velocity.

Feb 6, 2023

By Imre Gombköto, Zoltán Pap, Ákos Debreczeni, Sándor Nagy

Eddy current separators have become generally used in waste recycling industry during the last decade. There are many papers dealing with separation processes on eddy current separators, and also many article describes particle trajectory and different particle features affecting particle trajectory. These data are used in modeling as well. Within the frame of R&D project called ‚Fundamental research into the exploitation of the economic development potentials of critical raw materials in international co-operation - CriticEl?, authors are aimed for using Eddy Current Separator (ECS) as a mechanical separation step of high value critical elements recovery of selected WEEE’s like display panels, PCB’s. ECS, equipped with 305 mm wide belt, and a concentric magnetic rotor is used for experiments targeted development of methodology for determining separability of different particles on ECS. The subject of our work was to investigate the behavior of model particles with different shape, conductivity (aluminum and copper), orientation and size in order to separate Al and Cu according to the results of many experiments were carried out in this field. However it looks like that throwing distance of one particle is only possible to describe by a certain distribution for even the same particle within the frame of the same conditions. Sample mean and standard deviation are depending on some of the particle feature and acting forces. The paper is going to draft the first results on the relationship between distribution of throwing distance and particle properties.

Jan 1, 2014

By G. D. Schena, C Chiaruttini

The feasibility is demonstrated of reconstructing the volumetric distribution of liberated particles and middlings by use of a damped, weighted least-square regularisation method. This allows a precise mass balance to be obtained around a separation/concentration unit, permitting evaluation of the partition curve (Tromp curve) of the separator. Areal grade measurements are made on polished sections of feed, concentrate and tailings and a kernel-based inversion technique is then used to obtain the volumetric grade distribution of the three assemblages. A plain kernel (number of occurrences) and a weighted kernel (each occurrence counted with its area) are used for the solution. Testing of the method on computer-generated synthetic areal grade measurements indicates that it offers a valid alternative to the tedious conventional procedure of conducting experiments with heavy liquids

Jun 21, 1905

By Donald Leroux, Dave Scott, Giovanni Di Prisco

"The Lady Loretta lead-zinc deposit in Northwest Queensland, Australia contains an average of 5.9% lead, 17.1% zinc and 97 g/t silver. Ore mineralization is mostly comprised of fairly complex intergrowths of pyrite, sphalerite and galena. Starting in 1998, Noranda Inc., the major joint venture partner of the project, conducted extensive metallurgical test work, which culminated in July - August 2000 in a series of Pilot Plant tests. A common thread to all the metallurgical work has been the deportment of a large portion of silver into non-payable metallurgical products. Average silver distribution from four Pilot Plants shows a distribution of silver in lead concentrate of 28%, whereas silver in zinc concentrate was 49%, and 23% in the final tails.The consistently poor silver recovery as well as the fairly unusual silver distribution, particularly in zinc concentrate, was considered an issue to be thoroughly investigated. A mineralogical plan was devised to determine if these particular metallurgical results were somewhat related to the nature and mode of occurrence of silver carriers. Work was performed to determine discrete silver-bearing minerals and/or silver contained in solid solution in a suite of commonly occurring sulphides. Ore microscopy, SEM methods, Electron Microprobe and Ion Microprobe analyses were all used to answer these questions, and to find the silver carriers, so a metallurgical plan could be devised to improve silver recovery.INTRODUCTIONPotential economic exploitation of the Lady Loretta deposit in Queensland, Australia is driven by revenue derived from zinc and lead flotation concentrates and co-product silver recovery in lead. Relatively low recoveries of payable silver to lead concentrate, and high silver distribution to zinc concentrate necessitated an investigation into the natu"

Jan 1, 2002

By R. Hogg

A standard procedure for determining size-specific gravity distributions of fine coal (including the -400 mesh fractions) by sieving and centrifugal sink-float separation is described. The significance of using a centrifugal sink-float technique and the effect of the magnitude of the centrifugal force on the separation of fine coal are confirmed in the present study. The relative merits of cumulative versus incremental sink-float are discussed. The procedure is evaluated quantitatively using data obtained for the products of froth flotation of -100 mesh coal.

Jan 1, 1994

By V. E. Christensen

AT most smelting plants, forced draft, induced by high stacks or fans, is used to carry the gases away from the furnaces, roasters, or sintering plants. Gases moving under forced draft carry varying amounts of solids in the form of dust and fume. Where the weight of the solids is material, and the metal content high, it is usually profitable to treat the gases to recover these solids. Baghouses, Cottrell treaters, and settling chambers are the common forms of plants used to recover solids from gases. To check on the efficiency of these plants it is necessary to know the volume of gas leaving the plant and the amount of solids carried by the gas. As the volume of gas is equal to the product of the velocity of that gas and the cross-sectional area of the flue, the determination of the volume includes the measurement of the area of the cross section and the determination of the velocity. The velocity is generally measured by means of the Pitot tube and Ellison differential pressure gage, although low velocities are best determined by means of an anemometer. The dust concentration is determined by passing a measured volume of sample through a filter and weighing the dust caught. From this the dust concentration per unit of volume may be calculated. It is necessary to assume that the gas is homogeneous or that each cubic foot of the gas contains the same weight of dust as every other cubic foot. Having the volume of gas passing through a flue per unit of time, and the dust concentration of the gas per unit of volume, the amount of solids may easily be calculated.

Jan 1, 1935

By Dennis Z. Mraz

An engineering procedure for designing the minimum separation between solution mined caverns in bedded salt deposit is described. The procedure is based on data obtained by in-situ and laboratory test methods. The formulae utilize the concept that salt rock under high pressure in a deep salt rock deposit would behave as a perfectly plastic substance, and that the active opening surrounding a typical cavern could be described by a circular ellipsoid. The paper describes the calculations required for the safe design of a solution mined salt cavern field.

Jan 1, 1984

By J. A. Finch

Solvent-coated air bubbles in the Air-Assisted Solvent Extraction (AASX) process achieve the dual role of high solvent specific surface area and ease of phase separation. The thickness of the solvent film is of fundamental interest but difficult to measure directly in the process itself. As an approach interferometry (in the UV-vis region) was used to measure the time dependent thickness of a film formed by blowing an air bubble in kerosene-based solvents. The film was stabilized by the presence of 1.5 ppm silicone oil, as employed in AASX. The film appears to comprise two layers; an outer "free" layer of almost constant thickness and an inner "bound" layer which decreased in thickness with time. The bound layer is considered relevant to AASX. For a 20 mm diameter bubble blown in LIX/kerosene solvent the initial thickness was ~ 3 um which decreased over 10 minutes to a final rupture thickness of 500 nm. The bound layer thickness and time to rupture decreased with decreasing bubble size. Correspondence to prior indirect estimates of solvent layer thickness is examined.

Jan 1, 2006

By Barry H. G. Brady

A state of stable equilibrium is required in a mine structure to ensure that small increases in the mined void are accompanied by only small displacements of the rock mass. Methods of determining the stability of equilibrium in a rock mass currently require a geometrically regular stoping layout, and introduce a number of simplifying assumptions. The method reported in this paper models the mine near-field using Finite Elements, and the far-field using Boundary Elements. The stability of equilibrium in the modelled structure can be assessed directly from the value of selected principal minors of the global stiffness matrix.

Jan 1, 1981

By J. B. Mitchell

Using digital image correlation the evolution of strain and strain at the onset of localisation resulting in a hot tear has been determined for alloys AA6111 and Al¬0.5wt% Cu during solidification. High resolution images of hot tear formation and growth were captured during a constrained bar test that incorporated a glass window above a central hot spot region. The images were analysed using digital image correlation software to measure the evolution of displacement and strain based on tracking the motion of discrete features on the as-cast surface of the sample. Temperature data was also acquired with a thermocouple cast into the sample in close proximity to the hot tear. The interval starting from the point immediately after solidification shrinkage ends (the metal pulls away from the glass) and finishing when the first sign of a crack or hot tear is visible to the eye was used to determine strain data. The minimum strain at which strain localisation occurs was found to be 0.0069 in AA6111 and 0.0021 for A1-0.5%Cu.

Jan 1, 2007

By William Lodding

That grinding may change a crystalline material both in a physical and in a chemical sense has been shown by a number of authors in recent years. Thus Mackenzie (1) and Bartha (2) reported the effects of careful grinding on muscovite, quartz, gypsum, dolomite, etc. Increase in specific surface produced by grinding implies increase in total energy of a system. Newly produced surfaces are chemically more reactive; dislocations may be introduced during grinding, and existing strain may be released by the same process, as shown by Holt et el. (3) All these changes are easily detected by thermal analysis, but it is not easy to separate the multiplicity of effects registered and to arrive at quantitative interpretations. This paper is an attempt to analyze by the use of thermal analysis some effects produced in grinding. In differential thermal analysis (DTA) one measures all thermal changes occurring in a substance during heating or cooling. Chemical changes, such as decompositions, synthesis, oxidation, reduction, etc., and physical changes such as phase transformations, changes in specific surface and in thermal conductivity, strain release, etc. By thermo gradmetric analysis (TGA) on the other hand only chemical changes involving weight loss or gain are recorded. Similarly gas evolution analysis (GEA) will register only reactions involving gas evolution, including water vapor, and oxidation-reduction. By performing two or all three of these thermal methods of thermal analysis simultaneously and on the same specimen one can separate the different effects registered and by difference evaluate their magnitude.

Jan 1, 1966

By G. Venkateswara Rao

The jigging of ferrous ore to produce higher-grade products has been practiced for many decades. This is due to easy separation, a beneficial trade- off between operating cost and reduced yield relative to Dense Media Separation (DMS). Jigging becomes prominent for beneficiation of iron ores in the coarser size range. At present drive is towards the use of under bed air pulsed jigs for the beneficiation of ferrous ores. The main advantage is that the under bed air pulsed jigs are capable of generating the large pulse of amplitudes required to fluidize a deep bed of heavy ores particularly lump iron ore up to 40mm size. The major jig parameters effecting the jigging operation are bed height, shape of the pulse, residence time, operating pressure, valve cycle time and water flow rate. With the pulse shape set correctly for optimum stratification rate, even it is still necessary to provide enough residence time, to ensure the difficult material will take time to migrate to the expected layer in the bed. In order to find the Jig Stratification Index (JIS) parameters like bed height, operating pressure, water flow rate, cycle valve time and shape of the pulse were optimized first by conducting various tests. Typical Iron ore samples from Odisha (both lump and fines) were subjected to stratification studies at residence time of 1, 5 and 15 minutes. Jig Stratification Index (JSI) for both lump (0.30) and fines (0.20) were determined by using APIC Jig. The maximum possible JSI was calculated by using heavy liquid separation test (0.42 for lump and 0.24 for fines). It is found that the jig bed JSI is less than the Heavy liquid JSI for both lump and fines. The ratio of Jig bed JSI to the heavy liquid JSI is 0.83 for lump and 0.71 for fines. The JSI and ratio of Jig bed JSI to Heavy liquid JSI are low for fines due to fluid turbulences causing some degree of remixing in the jig bed. The fluid turbulences are more for fines than lump, hence jigging of fines is difficult and challenging. Keywords: sub grade iron ore, gravity separation, jigging, apic jig, stratification, residence time, jig stratification index

Sep 1, 2012

By B. P. Watson, T. J. Maphosa, D. P. Roberts, L. J. Gardner

The results of FLAC3D modelling on chromitite Upper Group 2 Reef pillars from the Bushveld Complex of South Africa are described. The model input parameters were determined from laboratory triaxial tests with post-failure measurements. These geomechanical tests were performed on rock materials within the pillars and the immediate pillar foundations. In the models, postfailure behaviour was simulated using the concept of cohesion softening. Models were built to determine the strength and behaviour of pillars with a width-to-height ratio of approximately two. The original research aimed to find a suitable depth below the surface where Impala Platinum Ltd could safely introduce crush pillars; however, the paper only describes the model results: the ideal depth of the crush pillar introduction is not discussed. The results of the modelling are compared with the PlatMine formula for peak pillar strength and with an underground instrumented pillar located elsewhere on the same reef. Some insight into the effects of grid size on strength is also provided. Further underground measurements are recommended to verify the model results

Sep 9, 2024

By B. C. Haimson

The Committee on Rapid Excavation of the National Research Council has recognized in its 1968 report the need for "improvement of rock-mechanics techniques for measuring subsurface stress field in deep boreholes and for determining stress distribution in walls of underground excavations". The technique recommended in this paper as being most suitable for both deep hole and tunnel wall stress determination is Hydraulic Fracturing. Using this method stresses are calculated directly from the fluid pressures necessary to initiate and extend a fracture away from a borehole. Stress determination by hydraulic fracturing is rather insensitive to inhomogeneity or anisotropy, is not limited in depth except by the length of the hole, requires simple equipment which is commercially available, and can be carried out by unskilled personnel. The method has been worked out theoretically and extensively tested and verified in the laboratory. A number of field tests in deep holes ranging from 300 to 6300 ft have yielded surprisingly good results. Preliminary underground tests have been very encouraging and most recent measurements in a tunnel complex at the Nevada Test Site yielded stresses that were both consistent and reasonable when compared with the expected directionsand magnitudes. It is recommended that hydraulic fracturing be considered as a method of in-situ stress measurement both in the pre-excavation stage of design and during tunneling.

Jan 1, 1974

By E. P. Polushkin

The object of this paper as to show that the structural composition of an alloy may be found by the planimetric measurement of the total area occupied by each of the constituents on a few representative photomicrographs of this alloy. When the area is determined the volume and the proportional weight of the constituent may be calculated. This method has been used for the determination of the structural composition of binary eutectics and other binary alloys with known constituents; also the composition of unknown constituents in binary alloys. The accuracy of the method is. high enough to justify its application to metallographic problems instead of the chemical analysis. THIS work has for its purpose the establishment of a new method for determining the structural composition of alloys. The area occupied by a constituent on a few representative photomicrographs of the alloy is measured, by a planimeter, especially designed for metallographic work, and the volume and proportional weight of the constituent calculated. Experiments have shown that 'the results are accurate enough to justify the application of the method to many problems in metallographic research instead of chemical analysis. The advantage of the method is the possibility, of determining the amount of the constituents with-out separating them from the alloy; their composition may also be determined if the ultimate chemical analysis of the alloy is known. DESCRIPTION OF PLANIMETER Suppose Fig. 1 represents a part of a photomicro-graph on which the total area of the black figures is FIG. 1?-PART OF PHOTOMICROGRAPH ON WHICH TOTAL AREA OF BLACK FIG- URES IS TO BE FOUND. to be found. By a system of parallel lines drawn short equal distances apart all figures may be divided into trapezoids. As the area of a trapezoid is equal to its median multiplied by its altitude, the relation between the total areas of the black and the white figures comprised within each strip is equal to the relation between the sums of medians for these figures respectively.

Jan 12, 1924

By Philip Drinker

IN THE mining and metallurgical industries, numerous problems arise requiring determinations of solid and of liquid particles suspended in air. Frequently, these problems are of local interest and involve purely economic or operating difficulties; on the other hand, toxic effects from the inhalation or the ingestion of substances suspended in air may be a matter of concern. For checking up process improvements or for determining ventilation efficiencies in problems of this general nature, various methods have been proposed. Although simpler methods are often satisfactory, precipitation combines several desirable features that other methods lack. This paper is, therefore, devoted to a discussion of portable alternating-current precipitators applicable to the quantitative determination and microscopy of dusts, fumes, and smokes in air. Small particles suspended in gases, such as air, are referred to in the literature as aerosols or suspensoids. Of these terms, suspensoids appears to be preferable as being more nearly in keeping with words in everyday use. In problems involving air pollution by small, particles-by suspensoids-it is convenient to distinguish three broad classes based on the size, the degree of dispersion, and the method by which the particles become suspended in the air. Dusts.-Particles or aggregates of particles, 150 to 1 micron in diameter, that are thrown into the air by mechanical agencies are termed dusts. Examples are silica, talc, cement, organic dusts such as hard rubber, starch, and cocoa; flocculated fume and smoke products. Fumes.-Particles, 0.2 to 1 micron in diameter, formed from chemical or physicochemical reactions are known as fumes. Examples are ammonium chloride, lead and mercury, zinc and magnesium oxides, fogs, and acid mists.

Jan 3, 1925

By Edgar Stansfield

WHEN plants decay in a peat bog the woody parts form a brown pasty mass, or peat muck, largely soluble in. alkalis. This brown matter has been termed "ulmin." The same material, but commonly black in color, is found in coal, and there is evidence of the similarity between the material forming the main bulk of the coal and the bulk of the more recently decayed material in peat bogs. The. more recent or low-rank coals, such as lignite, little removed from the peat stage, contain notable percentages of alkali-soluble ulmins, but the percentage decreases with increased, degree of coalification and is negligible in bituminous or higher rank coals. The determination of the alkali-soluble ulmins in any coal gives, therefore, an indication, of its degree of coalification or rank. Coals which contain few or no ulmins soluble in alkalis do contain ulmins which can be rendered soluble by oxidation. The higher the rank of the coal, the more difficult it is to oxidize the insoluble ulmins and make them soluble. High-rank coals can be differentiated by oxidation tests on the, insoluble ulmins; but low-rank coals can be characterized by both their soluble and insoluble ulmins. This paper deals with the determination and significance of the alkali-soluble ulmins, present, as such in- the coal. The chemical nature and composition of ulmins are not discussed.

Jan 1, 1932

By O. Lietard, J. Yvon, R. Mercier, J. F. Delon, J. M. Cases

INTRODUCTION Fineness is one of the main characteristics of powders and this parameter is the object of several definitions based on criteria connected with their uses as well as their determination methods. In trying to obtain the best reaction surface, fineness is characterized by the determination of the specific surface, but in other cases, particle size analysis is used. These two main methods are not, in fact, entirely independent and their complementary nature provides information concerning the morphology of the particles. In the case of a product formed by isodimensional spheres, the relationship between the specific surface and the diameter is well known: [S = 6 spd] where p is the specific weight of the material and d the diameter of the spheres. With no monodimensional spheres, but rather a granulometric distribution whose occurrences follow a mathematical law (1), the relationship is more complicated. The relationship between the specific surface measured by gas adsorption and the data of the particle size analysis is much more difficult to predict in the case of asymmetric porous particles, whose particle size distribution curves do not correspond to a known statistical law.

Jan 1, 1980

By B. Csoke

The Bond and the Hardgrove methods are widely used for the determination of the material?s grindability. Generally, the determination of the Bond work index of inhomogeneous materials can be carried out with high deviation using the conventional apparatuses and methods, because of the highly different grindability of components. This is more significant when the composite cement?s grindability is measured, which highly affects the design and operation of cement grinding mills. A possible solution can be the combined application of the Bond-method with the determination of the component?s weight ratio in the product and perform the Bond measurement until the steady state conditions of grindability coefficient (G) and chemical composition of the components are reached. To prove the applicability of the above mentioned idea systematic Bond and Hardgrove grindability tests were carried out of two phase composite materials. The experimental results showed that the application of the combined procedure is proven in order to have a more accurate and reliable calculation of the Bond work index of composite materials, especially when the components have significant difference in the grindability and concentration. The measurements also showed the possibilities and limits of the grindability test methods.

Sep 1, 2012