Search Documents

By S Pollak, A Amon

This paper describes the current and finished design work which has been performed for shallow rock station caverns for New York CityÆs first new subway construction in 60 years. A new robust, sophisticated, design procedure has been developed for two up to 30 m wide caverns, with overburden of less then 12 m, and rock cover to span ratios (C/S) in the order of 0.25. The design is based on empirical input parameters like the Q-value, rock mass rating (RMR) values, rock mass class after Cording (1984), cover to span ratios, which have been validated by the use of structural computer models as well as two- and three-dimensional numerical discontinuum models. The design approach is a staged approach using first principles, empirical models and non-linear FEM and DEM models. In addition, the paper describes the factors and circumstances why shallow caverns have been selected instead of cut-and-cover structures and why all the underground station structures have been developed as drained structures.

Jan 1, 2008

By Frank P. Frandina, Diane R. Hirsch, David P. Field, Colin R. Weeks

To accommodate growth in air service and to follow the Master Plan for long-term airport development, the Metropolitan Washington Airports Authority established thed2 Development Program at Washington Dulles International Airport. A sub-surface Automated People Mover (APM) System is under construction to replace the Mobile Lounges as the primary people mover system at Dulles. To minimize disruption to airport operations the majority of the APM System’s crossings of Taxi lanes will be undertaken using Tunnel Boring Machines (TBM) or the New Austrian Tunneling Method (NATM). This paper explores the planning and design of these shallow tunnel segments for future generation aircraft loads, within the constraints of minimal construction access under post 9/11 security requirements and the context of the overall airport expansion program.

Jan 1, 2005

By Jan Pru?ka

This paper describes the sheet pile design for the Line C extension from Ládví station to the North of Prague. The first part of the paper describes the geological conditions and structural configuration of the project. Typical cross sections, the description of the construction stages, and monitoring are discussed. The second part of the paper focuses on the sheeting design method. It describes the method of dependent pressures, that is, how the pressures acting upon a structure depend on the deformation. The design process and verification methodology are described in detail with comparison of the results with in-situ monitoring.

Jan 1, 2011

By Alan Peacock

Shield supports have been in use in the USA underground mines since 1975, and their development in the intervening time has been progressive and inovative. Specialized techniques are used to optimize their performance in a particular application and to design the component parts.

Jan 1, 1981

By N. Katsikaros, N. S. ‘ Yap, B. Adaszynski

"Cyanide is a well proven, effective lixiviant that has been utilised for centuries in gold extraction processes. Despite being used in close to 90% of gold processing plants, cyanide leaching is still being scrutinised due to its toxic nature. With governments tightening the regulations on cyanide management, and recently erected sites situated closer to community and environment, leach waste and tailings treatment has become increasingly important. Gekko Systems has worked with engineering companies and directly with gold producers to provide technical services and supply complete modular cyanide destruction (detox) systems for plants leaching both run-of-mine ore and high sulphide gravity and flotation concentrates. Although similar in principle, the different materials presented unique challenges in design and implementation. Similar to designing any section of a processing plant, the development of the cyanide destruction plant design began with laboratory test work to simulate the full scale operation. This paper focusses on the laboratory test work and how other critical factors such as geographical location, logistics, and local community play a role in the process design and construction. Two design and supply cases are discussed in this paper; one treating intensive cyanidation concentrate leach tails and one treating whole ore CIL tails. Although these plants both use the SO2/O2 process, each presented different challenges in laboratory testing and plant design, resulting in variations in final implementation including reagent choice, oxygen supply, and process control.INTRODUCTIONSince 1887, cyanide has played a large part in the beneficiation of gold from gold bearing ores. Cyanide is used to solubilise gold into solution, and is typically added in excess to maintain the leaching process. Some or all the excess cyanide can often be recovered and reused in the process however chemical destruction of cyanide is often necessary to manage cyanide levels in the tailings storage facility (TSF)."

Jan 1, 2016

By Patricio A. Espinoza, Aldo Casali, Cristian Ardiles, Guillermo González

Cluster analysis is used to design grade soft-sensors in a rougher flotation plant and a ball mill overload soft-sensor. Soft-sensors are virtual sensors which either replace unavailable actual sensors or infer measurements for non existing sensors. In the case of the grade soft-sensors clustering serves to determine clusters of related operating points. To each cluster there corresponds an ARMAX model structure whose parameters are estimated using only the points in the corresponding cluster. Thus a much better correlation is found than if all the data points were used for a global model. The problem of identifying clusters when the measurement of the real sensor is not available is addressed. In the case of the overload soft-sensor, variables were selected which are related to overload, either from a phenomenological point of view or according to operator experience. Different clusters are formed, some of which are identified as determining an overload condition or a possibility of such condition. Each of these clusters has a set of operating conditions which suggests the corrective action to be taken when necessary. Both kinds of soft-sensors are tested with industrial plant data and promising preliminary results are obtained.

Jan 1, 1995

By J. Beddoes

Many high strength aerospace alloys undergo solution heat treatment (SHT) and aging to develop precipitate strengthening. Most simply, SHT involves an isothermal hold in a single phase region followed by relatively rapid cooling to develop a super-saturated solid solution from which precipitates form during aging. However, subsequent properties are sensitively dependent on the details of the SHT, which frequently also serves a homogenization function. Altering the details of the thermal cycle during SHT significantly improves the properties attained during aging, as presented by examples of SHT design for titanium aluminide intermetallics, polycrystalline and single crystal superalloys, and 7075 aluminum.

Jan 1, 2010

By Feng Tianran, Lu Shijie, Shen Zhengchang, Han Zhibin, Tan Ming

"As a kind of non-metallic material, high-purify quartz sand has been widely used in many fields. Flotation is a popular way to process quartz sand. But it is in difficult position for flotation to get high-purify quartz product due to large amount of coarse particles contained in the feed. In this paper, a design principle of special flotation cell for high-purify quartz sand has been put forward base on ore property analysis and laboratory test, and the pilot scale special flotation cell has been developed to meet the requirement of the quartz sand flotation process. The special flotation cell for high-purify quartz sand is featured by middle positioned impeller, false bottom and draft tube, which could decrease the rising distance of mineralized bubble and strengthen the circulation capacity of the lower part of the flotation cell. Hydrodynamic study indicates that high air dispersion degree and strong lower slurry circulation could be produced by pilot scale special flotation cell, which is helpful to create a suitable hydrodynamic environment for quartz sand processing.INTRODUCTIONNatural quartz is a non-metallic mineral, which is widely used as raw material in multiple industry process (Shifu, 2006). High purity quartz, especially containing more than 99.9% silicon dioxide, is characterized by high temperature resistance, small thermal expansion coefficient, highly insulating and so on. The demand of high purity quartz has been rising along with social and economic development, now high purity quartz is widely used in the field of photovoltaic industry, electronic information, communications and aerospace industry.Quartz is a kind of main rocking-forming minerals in the nature. There are seven genetic types, such as natural crystal, quartz sandstone, quartzite, vein quartz, konilite, natural siliceous sand, granite quartz (Baolei, Shuilin, & Dianchao, 2012). The natural crystal is primarily used as raw material to refine high purity quartz, but it is not available for two reasons. On the one hand, the natural crystal is extremely expensive and poor in resources reserves, which can not satisfy the need of large-scale industrial production. On the other hand, the chemical component of natural crystal is instability, it may lead to low stable product performance in large industrial applications, and it is also difficult to achieve raw materials standardization. Therefore, there are a lot of studies to search for other technological methods to obtain high purity quartz from other genetic quartz types."

Jan 1, 2016

By Pierre Choquet

"The whole work carried out both in situ and in laboratory by a research group of the West German collieries is presented. This work has led to a design method of steel arch supports for gate roadways that gives full satisfaction in this particular coalfield. The method accounts for mining depth, the mining system (advancing or retreating), thickness of the coal seam and other parameters.Full statistics are then given on gate roadway supports of the ECCS (European Community for Coal and Steel) coalfields. They were collected by the author in order to show that the West German method can be applied to other coalfields as the long wall systems which are generally being used are very similar. Design calculations are conducted for each coalfield's case. They show that the method would have been able to predict in most cases the support actually used.Utilization of the design method is recommended to the Cape Breton Development Corporation 's mine operators because mining conditions, even though different from European ones, present a number of similarities which make it possible to apply the design method to their particular case.This procedure might be profitable in mines facing support problems in their levels and for any planning of future projects"

Jan 1, 1986

By M Chappell

This paper describes the design of the steel fibre reinforced precast concrete (SFRC) segmental lining for the intake and discharge tunnels for the Gold Coast desalination plant in Queensland. In addition, the key design requirements and design methods for the lining of these 2 km long, 2.8 m internal diameter tunnels, including structural, durability and maintenance requirements are discussed. Details of the segment configuration and erection process are presented along with information on the manufacture and trial testing of the concrete for the segments. The paper also gives a brief introduction to steel fibre reinforced concrete behaviour. Construction of the tunnels commenced in April 2007, and the authors believe this is the first application of this technology in Australia.

Jan 1, 2008

By S. V. Subramanian

The tool material and the machine design for high speed machining are well advanced over the last decade but the steel design has lagged behind. The paper examines the design of steel in order to control the sliding tribology for high speed machining under dry machining conditions. In high speed machining of steel, accelerated chemical wear of the tool occurs once atomic contact is established at the tool-chip interface, resulting in poor tool life even with high performance tools such as cubic boron nitride. Recent research has confirmed the occurrence of nanocrystalline grains in the interfacial layer of the chip at the tool-chip contact. The volume percentage of grain boundary is increased significantly (10 to 30%) as the nanocrystalline grain size is decreased well below 30 nm. The solubility of tool material into the nanocrystalline grain boundary is two or three orders of magnitude greater than in the crystal lattice. Further the kinetics of diffusion in the grain boundary is seven or eight orders of magnitude greater than in the crystal lattice. Enhanced nanocrystalline grain boundary diffusion occurring in the interfacial layer at the tool-chip contact causes the accelerated chemical wear. Significant improvement in tool life could be achieved by engineering glassy oxide inclusions in steel, designed to self-lubricate the tool-chip interface in-situ at higher cutting speeds. Thus the control of sliding tribological condition at the tool-chip interface is key to suppress nanocrystalline layer formation at the tool-chip contact and hence prevent accelerated chemical tool wear. Sulfide inclusions are designed essentially to promote chip fracture. In addition, sulfide inclusions are designed to act as a diffusion barrier at the tool-chip interface. The application of inclusion engineering concepts to enhance the tool life in high speed machining will be demonstrated with a suitable case history.

Jan 1, 2006

By B. Strickland

The decision to accelerate development of Stillwater Mining's East Boulder Mine was made in March of 1998. It required the completion of conceptual designs by July of 1998. This was accomplished through teamwork and close cooperation of mine personnel, engineering firms and vendors, all working toward the common goal of developing an efficient and workable design. Early in the project, representatives of Stillwater Mining, Kilborn International, Parsons Brinckerhoff Transit and Rail Systems, Continental Conveyor, and H.A. Simons met to develop methods to bring the mine into production at a highly accelerated rate and to solve potential bottlenecks, including the movement of personnel, materials, and muck through a 5.6 km (3-1/2 mile) adit. This interaction, including companies not normally associated with the mining industry, led to innovative approaches and designs produced by Kilborn Engineering and Stillwater Mining.

Jan 1, 1999

By D. Einarson, B. Strickland

The decision to accelerate development of Stillwater Mining’s East Boulder Mine was made in March of 1998. It required the completion of conceptual designs by July of 1998. This was accomplished through teamwork and close cooperation of mine personnel, engineering firms and vendors, all working toward the common goal of developing an efficient and workable design. Early in the project, representatives of Stillwater Mining, Kilborn International, Parsons Brinckerhoff Transit and RailSystems, Continental Conveyor, and H.A. Simons met to develop methods to bring the mine into production at a highly accelerated rate and to solve potential bottlenecks, including the movement of personnel, materials, and muck through a 5.6 km(3-1/2 mile) adit. This interaction, including companies not normally associated with the mining industry, led to innovative approaches and designs produced by Kilborn Engineering and Stillwater Mining.

Jan 1, 1999

By M. N. H. Khan

CSIRO has been experimenting with supersonic flows as a method of rapidly quenching metallic vapours. Cooling rates above 106 °C/s have been achieved. The supersonic flow conditions are achieved by adiabatic expansion of the vapour through a Laval nozzle into a vacuum chamber. This paper will describe the basic physics of the process, outlining computer fluid dynamic (CFD) modelling of flow in the nozzle, the effects of different flow conditions on the condensation process and discuss the practical design issues associated with operating supersonic nozzles. Results obtained from a CFD model of the nozzle, which compared two methods of incorporating condensation, showed that inclusion of condensation substantially changes the conditions in the nozzle. Most noticeably, the effect of condensation produces a region in the nozzle where the temperature remains almost constant.

Jan 1, 2006

By A. J. Hendron, D. U. Deere, F. D. Patton, E. J. Cording

In the design of structures founded in the near-surface rock, a distinction may be made between those problems that are related to the strength of the rock mass, and those that are related primarily to the compressibility of the rock mass. The mining engineer deals almost exclusively with problems involving strength in the design of open-pit slopes and underground openings. The civil engineer is similarly concerned with strength problems in the design of vehicular and water tunnels; underground power plants; cut slopes in rock for highways, canals, and spillways; and in the study of the sliding resistance of the foundations of gravity dams and the abutments of arch dams. Moreover, the civil engineer encounters problems in which the compressibility of the rock becomes the key element in the design. These problems include settlement of heavy structures supported on rock, deformation of the abutments of arch dams, and deflection of pressure tunnel linings. The design problems listed above are still solved largely on the basis of experience and rule-of-thumb. However, recent developments in rock mechanics give promise of providing more realistic approaches to certain aspects of the design. This paper, presents some of the more important recent developments which contribute to an understanding of rock behavior and which aid in design of rock structures. Typically, four steps are involved in the design of a structure, whether it be a machine element, a structural member of a building, or a structure in rock. These steps are listed below:

Jan 1, 1967

By Seungyeol Lee

Currently, a new construction method using a robotic system is widely spreading in construction sites. This study is related to the design of glazing robot?s teach pendant which can improve convenience of handling and hence improve the productivity through the efficient interaction between an operator and a robot while doing glazing works, e.g., curtain wall installing. The suitability of selection and arrangement of control switches was assessed according to mechanical motions of a glazing robot, and design guidelines for improving convenience and productivity were drawn up through questionnaires carried out by site operators. To verify the proposed design guidelines, working time comparison of the proposed teach pendant and the existing teach pendant was executed.

Aug 1, 2013

By I. Masters, K. Buban, M. Faris, M. Antonio, M. Collins

"AngloGold Ashanti Brasil, with assistance from Sherritt International Corporation, has recently commissioned a new autoclave for the pressure oxidation of refractory gold feeds at their Corrego do Sítio operation in Brazil. Design of the new plant, including feed acidulation, pressure oxidation, oxidized solids washing and solution neutralization circuits, was based on the results of test work conducted by Sherritt at their pilot plant in Fort Saskatchewan, Alberta. This paper describes the results of the pilot plant study as well as highlights of the design exercise.INTRODUCTIONAngloGold Ashanti Brasil (AGA Brasil) has recently commissioned a refractory gold pressure oxidation plant at the site of the original São Bento operation in Brazil. The design of the São Bento pressure oxidation facility was based on Sherritt technology; Sherritt carried out the original process development test work in the mid-1980s, provided a process design package and detailed specifications for critical pressure oxidation equipment and participated in the training of operators and commissioning of the plant. The São Bento plant was operated between 1986 and 2007, when the original ore body was exhausted (Silva et al., 2004). AGA Brasil purchased the facility from Eldorado Gold in 2008, with the intent of refurbishing the plant to process refractory gold concentrates produced from the nearby Córrego do Sítio mining area.Sherritt International Corporation has a long history in the development and application of commercial pressure oxidation and pressure leaching processes. Sherritt’s development of technology for the pressure oxidation of refractory gold ores and concentrates commenced in the 1980s in collaboration with Homestake for application at the McLaughlin project in California. This was followed by several commercial applications in Canada, Papua New Guinea and Brazil (Berezowsky et al., 1991). More than thirty pilot plant campaigns investigating the pressure oxidation of refractory gold ores or concentrates have been conducted by Sherritt since the 1980s, and projects with Sherritt contributions to the process development studies and/or engineering design account for about half of the commercial plants that have operated to date with this type of process (Collins et al., 2011a; 2011b)."

Jan 1, 2012

By Dominick Mandalari, David Mast, Heather Ullinger, Juan Granja, Amanda Foote

The City of Akron will construct the Northside Interceptor Tunnel project, a U.S. EPA/ DOJ CSO Long Term Control Plan Project. The system will provide at least 10.3 million gallons of storage in a 16.5-foot finished ID and 6,660-foot-long rock tunnel. The system will reduce both overflow volume and number of overflow structures on the Cuyahoga River. The project includes deep drop shafts and more than 3,000 linear feet of 48 to 96-inch I.D. sewers installed by trenchless construction methods. This paper will discuss the project background, ground conditions, and other challenges overcome during the design phases.

Jun 13, 2023

By G. H. Kuhnhausen

The Bear Creek Uranium Mill was designed in 1975 to process 909 tonnes per day (1000 STPD) of low-grade uranium ore from the Powder River Basin in Wyoming. The mill was expanded to 1818 tonnes per day (2000 STPD) in 1979. The Bear Creek Uranium Project is owned by the Bear Creek Uranium Company, a partnership of Rocky Mountain Energy Company and Mono Power Company. The original mill design contemplated processing ores from Bear Creek Uranium Company properties exclusively. The expanded capacity has been utilized for tolling ores from Kerr McGee Nuclear Corp. and other mining companies in the region. This paper describes the process of designing the original mill, the lessons learned from operation, and the design of the process modifications required for expansion. The project background, design philosophy, design basis, design criteria, actual flowsheet, special design considerations, and a comparison of assumed operating conditions and actual operating results will be presented. Bear Creek Uranium Company wishes to thank and acknowledge the help granted by the many operating companies who provided invaluable information, insight, and critique of the Bear Creek design through all the various stages and were instrumental in the successful completion and start-up of the mill. Without their contributions, the design philosophy used at Bear Creek would not have been possible and the results obtained would surely have been less satisfactory.

Jan 1, 1979

By G Lane, S Morrell

The design of the 12 m diameter SAG mill installed at the Cadia Hill Mine in New South Wales followed after two years of extensive laboratory and pilot plant testwork. The testwork showed the Cadia ores to be hard and competent necessitating the use of both a variable speed SAG mill drive and pebble crushing. The grinding power requirements for the SAG mill was based on engineering in-house grinding software, pilot plant data and simulations using JK SimMet software. Surveys of the SAG mill operation during the first four weeks showed the feed size distribution, transfer size and pebble rate to be lower or less than those for which it was designed. To compensate for the lower pebble rate, the SAG ball load was increased. This resulted in the total comminution circuit power being some 0.5 kWh/t higher than predicted. The JK SimMet SAG model has been modified to take account of these variations.

Jan 1, 2000