Search Documents

EnergyAustralia is a state-owned corporation in the state of New South Wales, whose responsibility includes ownership and management of an electricity distribution network. Expansion of the high voltage distribution network in the Sydney central business district (CBD) includes the requirement to run an additional five 132 kV feeders over 1.7 km from south of the CBD to a new 132 kV substation in the northern section of the CBD. A driven tunnel is currently being excavated in Sydney sandstone beneath Darling Harbour to contain the new 132 kV feeders. Tunnel construction methods involve both roadheader and tunnel boring machine (TBM) excavation. This paper describes the design development of the cable tunnel, discusses the use of a geotechnical baseline report as an integral part of the contract documentation and provides an update of the current construction works.  

Jan 1, 2008

By David R. Beadman

This paper discusses how modern techniques of design and construction were used to create the deep stations for the Copenhagen Metro. The deep stations are located in small squares within the city adjacent to many old and sensitive buildings. The architectural design provides a large open atrium to allow natural light to reach the column free platforms to give the citizens of Copenhagen a feeling of safety and security and encourage them to use the Metro. The design and construction contract was undertaken using the relatively new and untried Eurocodes. The resulting stations set new standards of design for underground metros and have pushed forward the frontiers of what is appropriate construction practice to protect the existing and enhance the future environment.

Jan 1, 2000

By Adam Pickles, Duncan Nicholson, Richard E. Prust, Hoe C. Yeow

"Moorhouse is founded on what at the time of construction were the deepest base grouted piles ever installed in London, specifically designed to accommodate settlement from the proposed development of Crossrail. This paper describes design and construction issues associated with this project with special emphasis on the construction aspects of installing these piles in a heavily congested site in Central London.INTRODUCTIONConstruction of the deepest base grouted bored piles in a congested site in Central London in 2002 posed a number of design and construction problems. To add to the complication, the new structure's footprint is within the safeguarded zone of the proposed new cross London rail link, Crossrail. Therefore the piles were required to be designed to allow for the effects of construction of the proposed Crossrail's tunnels and a new station at Moorgate. The design and construction issues associated with this project are described in this paper and methods used to address such issues are presented.MOORHOUSE DEVELOPMENTThe new nineteen storey high Moorhouse building was commissioned by Moor House Limited Partnership and will form another new Central London landmark building by the British architect Foster and Partners. Two of the four facades feature complex geometry to fulfill the city's planning requirements. The building is a steel frame structure stabilised by a reinforced concrete core. Floor plates span between the core and the perimeter with two rows of internal columns.The complex geometry of the superstructure requires a diagonal ""bandolier"" to transfer floor loads to certain perimeter columns. Another salient feature of the superstructure is the ribs that are provided to act as sloping columns to carry the loads down to the foundations."

Jan 1, 2005

By W. L. Chong

For a project located in Docklands Victoria, a high-rise development was proposed where the geology comprised soils of various compositions and consistencies to approximately 50m deep before being underlain by a siltstone bedrock. Due to the structural loads and spatial constraints, the majority of the foundation piles were designed to be socketed into the siltstone. Key factors in selecting the Continuous Flight Auger (CFA) technique as an effective piling solution are explained. These factors included structural and geological considerations, piling rig capabilities, pile testing regime to verify load performance and integrity, the extensive suite of construction quality controls and instrumentation records required while also achieving an appropriate piling budget and program. This paper also described how these factors underpinned the design approach of the final piling scheme. Critical aspects considered during construction and post-construction quality and pile testing records required to meet and satisfy the strict project piling specifications are also presented. The project adopted what may be considered the “best practice” in deep CFA piling. To the author’s knowledge, this project achieved the record for the deepest CFA piles in Australia where multiple piles to 53.8m deep were constructed.

Nov 1, 2022

By Andy Alder

The Docklands Light Railway (DLR) Extension to Woolwich Arsenal provides a much-needed public transport link to this area of London. The project includes construction of 5.3mID running tunnels under the River Thames, in ground conditions that proved challenging for the Earth Pressure Balance Tunnel Boring Machine (TBM). The project also includes cut and cover tunnel approaches, an underground station, and an emergency shaft on the bank of the river. Major challenges have included tunneling under sensitive infrastructure, and working adjacent to existing operational railways at Woolwich Arsenal. This paper will describe the design and construction of the project and how these challenges were overcome.

Jan 1, 2008

By J. Peshel

This paper presents a regulatory perspective of the design and construction of the Exploratory Shaft Facility which may become part of the future high-level waste repository. Site characterization concerns and long-term waste isolation concerns require the consideration of various shaft design and construction aspects quite different from that of conventional shaft sinking.

Jan 1, 1989

By Geoffrey Hughes

The Narragansett Bay Commission (NBC) is a regional sewer authority that serves ten communities in the Providence, Rhode Island metropolitan area. From 1992 to 1999, the NBC developed a comprehensive facilities plan to abate Combined Sewer Overflow (CSO) pollution in the Upper Narragansett Bay. The plan underwent many major evolutions during this period, most notably the addition of a stakeholder?s process by which NBC demonstrated a site-specific plan to control the pollutants and meet water quality standards. The favored solution consisted of deep tunnel storage with treatment at existing wastewater facilities that had been recently upgraded. In 1999, a final plan was accepted which included two tunnels, five CSO interceptors, twelve sewer separation projects, a wetland facility, and a wastewater treatment facility upgrade. The program is to be constructed over 20 years in three sequential phases (Figure 1). Phase I of the program includes a 4,963 m (16,284 ft) long, 7.9 m (26 ft) diameter, 70.1 m (230 ft) deep storage tunnel; seven drop shafts with connecting adits; ancillary facilities; and a pump station. Construction of Phase I began in 2001 and is expected to be operational by October 2008. This paper focuses on design and construction of the Fields Point Tunnel Pump Station (FPTPS)located at the south end of the main spine tunnel. A189 Ml/day (50 MGD) pump station is required to lift CSO flows from the tunnel to the Fields Point Wastewater Treatment Facility (FPWWTF). The pumps are to be housed in a 35.6 m × 18.6 m ×20.7 m (117 ft × 61 ft × 68 ft), 91.4 m (300 ft) deep cavern excavated in a complex meta-sedimentary rock of the Rhode Island Formation, and connected to the surface by 9.7 m (32 ft) and 3.4 m (11 ft) diameter shafts. Factors which influenced selection of the size, configuration and location of facilities included the preferred arrangement of pumps, critical aspects of site geology, and estimated cost. Technical and value engineering reviews also affected the final design. Following Notice to Proceed (NTP), concerns were raised by the contractor regarding constructability and design. Additional geotechnical investigation and independent engineering review were employed to validate the design assumptions. The cavern was successfully excavated and sup-ported in rock, completed on schedule and within budget in 2005. In 1992 the NBC retained Louis Berger Group (LBG) as Program Manager (PM) for the CSO Abatement Program. LBG thereafter formed a design team including: Jacobs Engineering Group(JEG) as the designer for underground structures and near surface collection facilities; Black and Veatch(B&V) to design the pumping system and associated facilities; Haley and Aldrich (H&A) to oversee the geotechnical program; and Malcolm Pirnie to design the system-wide instrumentation and control system. Construction management, resident engineering, and inspection services were provided by the joint venture Gilbane/Jacobs Associates (G/J).

Jan 1, 2008

No paper was submitted for the proceedings, verbal presentation only (no material available).

Jan 1, 1998

By M. Wittke

"In the course of the extension of the railway network in Israel, currently the two 4.6 km long tubes of the Gilon Tunnels on the line from Akko to Carmiel are being constructed. The tunnels run through the limestones of the Bina- and Yirka-formations, which locally are karstified. The maximum overburden amounts to 160 m.The limestones are mostly horizontally bedded and vertically jointed. Occasionally also inclined joints exist. The tunnels cross various fault zones, which mostly strike at an acute angle to the tunnel axis and are steeply inclined. The karstic cavities which were encountered during tunneling have partially been filled by clay. In the vicinity of the fault zones, the rock has often been strongly jointed and weathered respectively. The two single-track tubes have a cross section with vertical walls and an open invert. The tubes are connected by cross cuts with a spacing of approx. 250 m.During the tender phase, WBI has elaborated the tender design for a joint venture of a Chinese and an Israeli construction company. After the joint venture had been awarded the contract, the preliminary and the detailed design have been elaborated by WBI and the construction works have been guided. On the basis of the geological description, rock mechanical models have been elaborated, followed by stability analyses on the basis of the Finite Element method. The tunnels have been excavated according to the shotcrete method. The support in most areas only consisted of a very thin shotcrete lining and radial bolts in the area of the roof. Depending on the degree of jointing and weathering, locally advancing support by means of spiles has been applied.The internal lining of reinforced concrete has been constructed in parallel to the heading of the tubes. Mucking and delivery of materials was carried out through the cross cuts.The breakthrough was achieved in April 2014 and thus within schedule. The predicted distribution of the excavation and support classes along the tunnel has been in good agreement with reality."

Jan 1, 2015

By Stephen J. Klein, Fernando Orduz, Randall J. Essex

INTRODUCTION The Keystone Tunnel project consists of widening an existing 7.3 m-wide (24 ft) highway tunnel to a width of 13.7 m (45 ft) to provide a three-lane, two-directional highway tunnel. The 13.7 m-wide tunnel was excavated in a staged drill-and-blast sequence through foliated schist, and was supported using pattern rock reinforcement and shotcrete. Notable project features are: the low vertical cover over the tunnel is less than the span of the opening; the project is the second instance where the Federal Highway Administration (FHWA) has accepted rock reinforcement as a permanent support element; and the project is the first instance where the FHWA is accepting shotcrete as the final interior surface of the tunnel. This paper covers the design and construction phases of the project. PROJECT DESCRIPTION The South Dakota Department of Transportation (SDDOT) retained Woodward-Clyde Consultants (WCC) to evaluate the feasibility, prepare construction plans and specifications, and provide construction management services for the widening of the Keystone Tunnel. The tunnel is located in the Black Hills National Forest area of South Dakota near the southwest corner of the state. The Keystone Tunnel is on U.S. Highway 16A, about 0.8 km (1/2 mile) north of Keystone which is approximately 32 km (20 miles) south of Rapid City (Figure 1). Highway 16A serves as an important transportation link between Rapid City and the Mount Rushmore National Monument which is located about 2 miles west of Keystone. The road through the tunnel consisted of two lanes about 7.3 m (24 ft) wide, and is being widened [ ]

Jan 1, 1989

By D. L. Petersen, C. R. Nelson, B. K. Nelson, B. D. Wagener

The Lafayette Bluff tunnel, currently under construction for the Minnesota Department of Transportation (MnDOT), will be among the widest highway tunnels in the United States. The 199-meter tunnel is being constructed in a closely jointed, variably weathered diabase rock mass. Cover above the tunnel crown ranges from 4 meters to 27 meters, and is less than the tunnel excavated width of 18.3 meters for about 60 percent of its length. These factors dictated special support and lining design, limitations on excavation sizes and required sequences for support installation. Tunnel excavation is by controlled blasting, with multiple top headings and bench. Rock support and lining consists of external portal beams, rockbolts and reinforced shotcrete. A final concrete lining provides structural support for the rock mass and the membrane waterproofing system.

Jan 1, 1991

By Y. Z. Wang

Zhengzhou Yellow River Highway Bridge, which is under construction, has a total length of 5550 meters with bored cast-in-place concrete piles as the foundations of its piers which have a diameter of 2.20 m with a length of approximately 65 m. This paper attempts, through the introduction of the said bridge's footing pile design and construction, mainly to give an account of the following points: 1) experiment and research on deep friction pile with a large diameter, 2) calculation of vertical carrying capacity of the pile with a large diameter, 3) analy­sis of horizontal forces the footing-piles of the column-shaped piers, 4) application of normal and reverse-circulation rotary drilling technologies to the construction of bored cast-in-place concrete piles with a large diameter and 5) applying super-sonic impulse on destruction detective device to examine the quality of the pile concrete.

Jan 1, 2010

By Hemang Desai

A damaged outlet pipe beneath Lenihan Dam has restricted reservoir discharges, severely constraining the owner?s groundwater recharge program. The solution, a new outlet pipeline through the dam?s right abutment, includes an approximately12.2-m-deep (40-ft-deep) shaft and 618.7-m-long, 4.3-m-diameter (2,030-ft long, 14-ft-diameter) tunnel mined in Franciscan melange composed of hard blocks of rock and soft clayey matrix. Alternating road header with drill and blast operations and using steel ribs and shotcrete have proven a flexible combination for handling the variable ground conditions. Excavating the shaft and connecting it to the tunnel require lowering the reservoir for five months, during which time careful construction sequencing and use of a tunnel plug eliminate the risk of an uncontrolled discharge.

By Alfredo Valdivia, Hamed Nejad, Vincent Monaco, William Cao

"The East Side Access (ESA) CM005 Contract - Manhattan South Structures - consists of the installation of the waterproofing and final concrete lining for railroad tunnels, 3-Level Wye track turnout structures, segments of the Main Cavern Station, and a series of Ventilation Structures excavated beneath the existing Metro North Railroad (MNR) Grand Central Terminal. Several key team decisions made collectively by the Construction Manager (CM), Designer, and the Contractor has allowed the scheduled construction duration of 29 months to be maintained. These strategies include the use of alternate design and construction methods, including the use of pneumatically applied concrete lining and precast lining. This paper discusses these strategies, and illustrates how successful teamwork and cooperation during the execution of a large-scale construction project can lead to lowering costs, improving quality, and maintaining the overall project schedule. INTRODUCTION The East Side Access Project The Long Island Railroad (LIRR) currently transports commuters from Long Island into Manhattan, terminating at the already over congested Penn Station on the west side of Manhattan. Once completed, the ESA Project will provide LIRR commuters direct access to the east side of Manhattan underneath Grand Central Terminal. The ESA Project will help alleviate the congestion at Penn Station, which currently accommodate the NJ Transit, Amtrak, and LIRR lines; reduce travel time for LIRR passengers traveling to the east side of Manhattan and facilitate connections to the NYCT Subway System and Metro North Rail Road. The ESA Project includes building new tunnels and facilities under Manhattan and Queens. (See Figure 1).The Manhattan Alignment In the Manhattan segment of the ESA Project the excavation in hard rock of tunnels, cross passages, caverns and shafts has been completed by tunnel boring machines, drill and blast, and road header. The construction of the structural concrete final lining, interior structures and fit-out of the previously excavated caverns and tunnels are currently being performed under Contract CM005 Manhattan South Structures awarded to Michels Corporation and Contract CM006 Manhattan North Structures awarded to Frontier Kemper Constructors Inc. This paper focuses on the design and construction aspects of Contract CM005 which is the first ESA Contract in Manhattan to successfully construct concrete final linings in pre-existing excavated areas."

Jan 1, 2016

By Stephen Navin, Pablo Ferradas, Carlos Silvestri, Alexander Markov, Jon Kaneshiro

In the high Andes of Peru, two tunnels are being constructed totaling nine kilometers in length at an elevation of over 4,500 meters. The tunnels convey freezing and crystal-clear waters from rainfalls, streams, and lakes for the consumption of Lima. The drill and blast 3-meter wide by 4-meter high tunnels are being driven from both ends through folded and sheared volcanic tuff, andesite, agglomerate,and limestone, where groundwater inflow is high. This paper describes the design geological and groundwater inflow investigations and construction.

Jan 1, 1999

By K. J. Brouwer, J. P. Haile

"Construction of the first stage of the tailings disposal facility for the Montana Tunnels Project was completed in October 1986. The project is located 37 km south of Helena, Montana, and involves mining of42 million tons of weathered diatreme are at a rate or 13 500 tpd to produce a gold/silver dore, as well as lead and zinc concentrates. The tailings disposal facility for the project includes a fully drained tailings impoundment for storage of the tailings solids, and a process waterpond for storage of all decanted water prior to recyling to the mill. The over-all facility is designed to achieve the basic objectives ofminimizing seepage to the environment in the short- and longterm, and achieving a fully drained stable tailings mass suitable for immediate reclamation on completion of mining. Specific features of the design include a soil bentonite seal and drainage system within the tailings basin, a free draining embankment with a design flow-through capacity of 4000 US gpm and an ultimate height of 230 ft (70 m), and a soil bentonite lined make-up water pond with a capacity of 420 acre-feet (530 000 m'). The tailings will be discharged in a rotational sequence through multiple spigot offtakes to achieve a thin-layer low energy laminar flow. This 'sub-aerial' deposition results in higher stored densities and maximizes liquid-solid separation on the tailings beaches. The over-all design played a major role in the successful permitting of the project, and was significantly cheaper than a conventional wet disposal system, with overall unit costs for tailings disposal of less than US$0.36 per ton.This paper outlines the site characteristics and the tailings material properties and their influence on the design. Extensive use was made of naturally occurring free draining materials as well as bentonite modified soil liners within the tailings basin, embankment and retention ponds. General construction procedures for the various components are described, as well as on-going construction requirements utilizing materials from the open pit. Finally, the over-all costs and unit costs for tailings disposal are presented."

Jan 1, 1988

By Abegail Endraca, Allan Sebastian, Andrew Raine, Allan Patdu

The project involves the construction of a new aqueduct tunnel by an Earth Pressure Balance TBM tunnel for the Novaliches-Balara Aqueduct No 4 (NBAQ4) project in Metro Manila. It comprises a 7.3 km long and 3.1 m internal diameter tunnel that can deliver up to 1,000 MLD of raw water and the tunnel passes under urban residential and urban populated areas adjacent to and along Commonwealth Avenue. A new reservoir intake structure was constructed in the La Mesa reservoir by a cofferdam and the TBM breakthrough connected the reservoir to the outlet surge shaft structure and the downstream pipe network system connecting to the Balara Water Treatment Plant. The TBM incorporated a double articulated head configuration to allow tight 80 m radius curves to navigate some of the difficult alignment considerations. The alignment passed very close to some existing foundations for MRT7 and needed to clear several tight curves to remain within government land ownership. The project excavated through the local Guadalupe weak rock formations and there was minimal ground movements observed as a result of the work.

Jun 13, 2023

By A Radici, M Attwill

The Dampier Port Upgrade Project (DPU) involves an upgrade to Hamersley IronÆs Parker Point iron ore port facility at Dampier, Western Australia. The $US700 million DPU Project will increase Hamersley IronÆs shipping capacity at Dampier from 72 million tonnes per annum (Mtpa) to 116 Mtpa. The DPU Project comprises a new car dumper facility and rail spur, an upgrade to the existing stockyard and conveying system, a new screen-house and a 450 m wharf extension with two new shipping berths and a new ship-loader. This paper discusses the innovative design and construction of the new car dumper facility, which is capable of automatically unloading 240 car iron ore trains at a rate of 10 000 t/h. The facility design is unique compared to more conventional designs currently in operation, and greatly improves operation and maintenance functions.

Jan 1, 2005

By David Mast, Amanda Foote, Mina Shinouda

The Michigan DOT’s I‑75 Modernization Project, Segment 3, is a 30-year, $1.2 Billion design-build-finance-maintain project in Southeast Michigan. The scope includes building a nearly 4-mile long, 14.5-foot ID stormwater storage tunnel. The tunnel and pump station are being built concurrent with new roads and bridges, requiring multiple levels of design and construction coordination. Underground risks include the poten‑ tial for encountering granular soils, groundwater, and explosive gases. The new tunnel will be mined by a new open-face TBM and lined with a one-pass steel-fiber-reinforced precast concrete segmental lining. Shaft construction began in early 2020 and tunnel mining in July 2020.

Jun 13, 2021

By S. J. Porter, M. T. McRae

The new tunnel at Genting Sempah is part of a privately funded infrastructure projectthat involves duplicating the existing highway extending from the Gombok Toll Plaza near Kuala Lumpur to Karak, in Malaysia. The 60 km long tollway includes an 800 m long, two-lane highway tunnel with excavated dimensions of 10.5 m wide by 8 m high. The majority of the tunnel extends through slightly to moderately weathered, moderately to highly jointed quartz porphyry. Excavation of the tunnel was performed using drill and blast methods and the primary tunnel support consists of rock dowels and shotcrete except for short sections adjacent to the portals where steel sets were utilized. A portion of the tunnel encountered sheared and altered material that was successfully supported using rock dowels and shotcrete. The final lining for the tunnel consists of mesh and fiber reinforced shotcrete. The flexible nature of the primary support and shotcrete final lining resulted in considerable cost savings and expedient construction methods.

Jan 1, 1997