Search Documents

By Jørn Thomsen, Christoffer Brodbaek

"As governments increasingly accord high priority to sustainable energy, policymakers are finding that wind energy has a long track record as a proven alternative to conventional energy supply.Over the past two decades, wind turbine projects have been constructed offshore because of more stable offshore wind conditions and because there is more available space for large wind farms out in the open sea. Vindeby Wind Farm in southern Denmark was constructed in 1991. As the world’s first offshore wind farm, it provided valuable information and experience for researchers and designers that have led to new technologies and design improvements, a trend that will continue as more offshore wind farms are constructed. Today, the world’s capacity of the installed offshore wind turbines exceeds 1,000 MW. Most of these are installed in Northern Europe where there was early political support and favorable conditions, such as strong winds and relatively shallow waters. Offshore wind projects are now under development around the globe, including continental Europe, the U.K. and North America. ‘The largest offshore wind farm today is Denmark’s Nysted Offshore Wind Farm, which has a total capacity of approximately 480,000 MWh, equivalent to the yearly consumption of 120,000 households. It is five to six miles offshore in the Baltic Sea in the southern part of Denmark.The owner is a joint venture between DONG Energy of Denmark and E.ON Sweden. Bonus Energy (now Siemens) supplied the wind turbines, and P. Aarsleff A/S and subcontractors supplied the foundations. The contractor’s consultant, COWI A/S of Denmark, developed and designed the turbine foundations. With a total capacity of 165.6 MW, the project consists of 72 Bonus 2.3 MW turbines in water depths up to 33 ft. The turbines have a hub height of 226 ft, and the turbine blade diameter is 270 ft. The rotor and nacelle (the structure that houses the generator, gearbox and other equipment) weigh approximately 150 tons, and the weight of the steel tower is approximately 130 tons. The wind farm site is located in a relatively protected area of the Baltic Sea, but during the winter months, the water often freezes and the foundations needed to be constructed to resist ice forces. The founding soils at the site are overconsolidated clay tills with boulders and with a thin layer of softer surface sediments. Pockets of up to 30 ft of soft sediments were encountered, which required special foundation preparations."

Jan 1, 2009

By Dempsey S. Thieman

The Kuparuk River Central Channel Bridge on the North Slope of Alaska provides critical access for oilfield service vehicles in the largest oilfield in the United States. The original sloped spill-through bridge abutments were protected by articulated concrete revetment. After 27 years of heavy service, ice impact, deep river scour, and high floods, the revetment required replacement. An OPEN CELL SHEET PILE® abutment was selected to replace the existing erosion protection and provide increased performance and structure life. Project engineers and contractors successfully addressed the challenges of low overhead sheet pile installation under the bridge, extremely heavy vehicle loads, and arctic winter construction conditions through innovative design and construction techniques. The project was successfully completed on schedule with minimal disruptions to critical bridge traffic. This paper provides a detailed discussion of the design and construction techniques utilized to address the challenges of the project, many of which could be adapted to other projects.

Jan 1, 2008

By Takefumi Takuma, Tsunenobu Nozaki, Masashi Nagano

Using sheet piles and pipe piles for permanent earth retaining is one of the most economical methods for constructing basement walls since they can also work as temporary shoring during construction. A major mixed-use redevelopment project in the UK, encompassing two to three large city blocks, utilized both sheet and pipe pile walls for a two-level subterranean parking structure. The 290m (950ft) x 100m (330ft) basement’s steel walls were designed to temporarily support excavation during construction and eventually to become a load carrying permanent structure in order to expedite the construction process and to achieve cost reduction. Two types of press-in piling machines, one for sheet piles and the other for pipe piles, were used for the job because of their abilities to press in sheet and pipe piles within tight tolerances for finished walls, for difficult installation conditions with very hard soil, and for its very low noise and practically zero-vibration operation; an essential factor for the job in close proximity to other businesses and residents. BACKGROUND Steel sheet pile and pipe piles have been used for many purposes including earth retaining. They are produced at steel mills and spirally welded at a fabrication yard to their corresponding specifications under strict quality control measures. Therefore, they can form highly reliable walls to its design capacity with proper installations. Their advantages as underground walls are:  They can form a high level of water cut-off function with their interlocks sealed by welding or with hydrophilic materials. See Figure 1 for a few examples for a sheet pile application.  They can carry vertical loading in addition to horizontal load and bending moment.  They can be a self-standing and temporary/permanent wall with flexible design and construction processes; bottom-up, top-down or hybrid sequences can be chosen per the project’s needs.  They can form a thinner wall than other wall types, creating larger inner space. See Figure 2.

Jan 1, 2019

By Nasr Sheta

"After Hurricane Sandy, the stability of an earth slope in the Atlantic Highlands, New Jersey in the United States was deteriorating due to slumping soils and erosion from flooding. A slope stability evaluation indicated the slope did not satisfy the requirements of the local building code. A triple-tier, pile-supported and mechanically stabilized earth wall was designed and constructed to stabilize the slope. The construction was planned from a 3-m-wide roadway and, because of rough terrain and limited work space at the site, a cast-in-place drilled-pile construction was deemed impractical due to slow pile production. An alternative procedure was utilized by pre-drilling holes, and installing precast tip-and-shaft-grouted (PCTSG) piles, which extended to competent soils to improve slope stability. A grade beam, connecting the PCTSG piles along with soldier beams and concrete lagging were used to form the lowest tier of the slope stabilization, while the middle and higher tiers were built as mechanically stabilized earth. The stability of the proposed stabilization was analyzed using 2-D non-linear finite elements. After construction, monitoring of the wall continued for about 8 months to check its performance, and indicated lateral and vertical wall movements were less than 25 mm and 6 mm, respectively, indicating effective slope stabilization.INTRODUCTIONStabilizing earth slopes using piles to connect near-surface unstable soils to underlying stable ground masses has been investigated by many researchers, who presented various approaches to evaluate the contribution of the pile system towards improving the stability of the slope. Some of these approaches consider the piles as structural elements receiving forces from the upper sliding ground mass and transmitting these forces to the underlying stable one. The force from the top sliding mass is applied at between one third and one half of the pile embedment into the top sliding mass, Anagnostopoulos et al. (1990), Fukuoka (1977) and Matsui et al. (1988). The point of application of the sliding force was explored based on successful case histories while addressing the safety factors for both geotechnical and structural design, Vessely A. et al. (2007). The development of numerical analysis techniques utilizing the method of finite elements (FE) also enabled better analysis and design of slopes stabilized using piles. A FE-based approach was successfully utilized to design slope stabilization with target safety factor based on the shear and bending demands and the spacing of the piles, Pradel D. et al. (2010).After Hurricane Sandy in October 2012, the stability of many properties constructed atop earth slopes located along the coast of the Atlantic Ocean has become a concern due to storm-induced erosion. This paper presents the analysis, design and construction of a hybrid slope stabilization system utilized at one of these storm-impacted properties, which is located in the Atlantic Highlands, New Jersey in the United States. The subject property consisted of a two-story residential dwelling and a parking structure, and was built on top of an about 8-m-high earth slope having crest at about elevation 10 m (el 10) and toe at about el 2."

Jan 1, 1900

By Verya Nasri, Agustin Rey

Once completed, the Montreal Réseau Express Métropolitain (REM) will be the fourth largest automated transportation system in the world. The REM represents construction costs of approximately 7.0 billion Canadian dollars. The project consists of 67 km of twin tracks over four branches connected to downtown Montreal. The project includes 26 stations with 3 underground stations in downtown Montreal. One of the underground stations was built using the NATM method with thin permanent shotcrete initial and final liners separated by a sprayed on waterproofing membrane. The 2 other underground stations were built with the cut and cover approach including one using permanent secant pile wall with permanent walers and struts as the support of excavation and the final perimeter wall of the station. The project also includes the rehabilitation and enlargement of the Mont Royal Tunnel. This 100-year-old double track tunnel is about 5 km long. The REM also consists of 3.6 km new TBM tunnel connecting downtown to the Montreal International Airport through saturated soft ground and karstic rock. By the time of RETC, the construction of REM underground structures will be completed. This paper presents the design and construction aspects of the underground structures of this mega project.

Jun 13, 2023

By Safdar A. Gill

The technique of installing small diameter caissons (drilled piers) through soft clays and water bearing ganular soil is well established for constructing building foundations. Over the past few years, the method has been utilized for constructing a large number of shafts extending into rock for the Chicago's Deep Tunnel Project. This paper will discuss design considerations for obtaining the most economic ground support system, the impact of construction procedures on the support and lateral pressures for design. Construction procedures will be described along with performance of the shafts.

Jan 1, 1981

By Fei-chiu Huang

A 17-acre landslide occurred in February 2001, on a slope below Via Bellota in the City of San Clemente, California. Three homes were destroyed and many others placed in jeopardy. The landslide, involving portions of five separate developments, continued to move significantly in the years following. Litigation ensued among the affected parties, and investigations continued through 2007. A mediated repair resolution was ultimately reached among the parties. The agreed upon repair consists of a multi-million dollar stabilization program that included grading, drainage, and structural systems. Part of the construction cost was offset by creating 4 new ocean view custom lots and 20 new mobile home lots. The landslide repair and slope stabilization design involved removal and replacement of portions of the landslide debris and construction of buttress and stabilization fills as well as installation of 74 shear pins in two rows. The shear pins were designed as 4-foot diameter by 50 feet in length and incorporated continuous W30x211 wide flange steel. The shear pins were designed to be installed 25 feet above the slide plane and 25 feet below the slide plane at each location. Construction of the 74 shear pins was initiated in 2008 and completed in 2009. Four-foot diameter holes were drilled by utilizing a truck-mounted, flight-auger-style drilling rig with a 4-foot diameter solid-flight auger. Prior to the installation of the shear pins, an engineering geologist downhole logged strategically selected holes to further evaluate the actual slide plane elevations. The wide flange steel shear pins were then lowered to the desired elevations and encased within 4,500 psi, Type V, 0.45 maximum water/cement ratio concrete. Inclinometers installed within four pin shafts and behind the pin rows indicated performance in accordance with the design. Slight to non-perceivable shear displacement was measured which mobilized the intended capacity at the monitored shear pins. No excessive slope movement was detected at any of the inclinometer locations during or after the construction period. Actual shear displacement of the steel wide flange elements was less than the movement anticipated before shear pin installation.

Jan 1, 2010

By Robert S. Thomas, Bernard M. Tarralle, Nasser Massoudi

"The Commonwealth of Virginia is restoring and expanding its Capitol of great historic significance. Designed by Thomas Jefferson in 1785, it is the second oldest Capitol building in the United States. The building expansion required excavations immediately adjacent to its South Portico. The building, which rests on shallow brick footings, is very sensitive to any disturbance caused by construction and excavation. A comprehensive and secure plan of operations was devised by the design team to ensure that this national monument remains unharmed by the new construction. Various construction techniques were implemented to satisfy the strict movement goal of 0.25 inch and distortion of U2000. They consisted of jet grout columns to stabilize the upper soils, compensation grouting for future foundation leveling, a tied-back reinforced concrete diaphragm wall for excavation retention and foundations, and realtime instrumentation for monitoring. This paper describes the design approach for the retention system, providing information on the various construction phases and techn iques, and reports on the movements recorded by the real-time monitoring system during the course of the project. At the time of this manuscript preparation, and the deep excavation complete to final grade, the results indicate that the extremely restrictive building movement criteria have been met. The success can be credited to detailed design, close cooperation among the project team, prudent construction methods, and real-time monitoring. INTRODUCTIONThe Commonwealth of Virginia is undertaking a comprehensive renovation and expansion of the Virginia Capitol building located in Richmond, Virginia. The Capitol building was designed by Thomas Jefferson in 1785, with construction of the original building starting the same year. The Capitol building was designated a National Historic Landmark in 1960 and was listed on the National Register of Historic Places in 1966.A part of the comprehensive renovation and expansion of the Capitol is a 25,000-square foot, two-level subterranean extension on the south side of the Capitol building, which will serve as a new Visitor Center and public entrance for the Capitol. Deep excavations were required for the construction of the new Visitor Center. The excavation required a permanent retention system to accommodate an approximately 40- foot deep excavation."

Jan 1, 2005

By B Chapman, R Nievergelt, J Hill

A major component of Sydney’s new South West Rail Link project is the Hume Highway Underpass (HHU), an 80 m long twin track mined tunnel excavated at a depth of just 5 m below the pavement of the Hume Highway; one of Australia’s busiest road corridors.In order to ensure a safe and efficient construction of the underpass without disruption to the Hume Highway traffic, design of the HHU required specific focus on the prediction and control of ground movements. This paper describes the design and construction solutions adopted in response to these challenging constraints. The paper also provides discussion on the observed behaviour of the underpass during construction and the results of a back analysis that was undertaken during construction.CITATION:Hill, J, Nievergelt, R and Chapman, B, 2014. Design and construction of Sydney’s South West Rail Link Hume Highway Underpass, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 375–386 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Bruce N. McIver, Leo Casagrande

Similarities are noted in the practices and problems of constructing dams to impound mine tailings, fly ash, and chemical wastes. The comparison of a typical tailings dam with a conventional water-retaining earth dam shows that the former is inherently less stable and can be susceptible to cracking, liquefaction, erosion, and frost action, as illustrated by examples. Several methods are presented for building safe tailings dams using either the coarse fraction of the tailings or local soils, the important factor in each method being proper compaction of the material. The safety of existing tailings dams can be improved by flattening the overall slope, preferably by adding berms, or by decreasing the height. Where neither remedy is possible, the installation of electro-osmotic tie-backs is suggested. Dumps of mine spoil can be stabilized economically by compacting the material in layers along the toe to form a dam.

Jan 1, 1971

By Earle J. Klohn

"The design, construction and operation of tailings dams is rapidly becoming a major consideration for most new mining developments, as well as for many existing operations. In North America, under pressure from public opinion, various government agencies have in recent years enacted legislation covering the design, construction and operation of tailings dams. In British Columbia, comprehensive legislation has been passed during the past year (1971). All of these new regulations may be placed into two broad categories: regulations concerning the safety of the dam and appurtenant structures, and regulations concerning the prevention of pollution. Both types of regulation affect the design of the tailings dam facilities. Consequently, they must be considered jointly by the designer. A good tailings dam design must satisfy the basic requirements of safety, pollution control, storage capacity and economy. To achieve this, 'the design must be based on a thorough understanding of both the geotechnical problems involved and the requirements of the mining development. Obviously, this requires close cooperation between the designing geotechnical engineers and the mining operators. This paper outlines the major engineering factors that should be considered in the investigation, design, construct ion and operation of tailings dams. Basic methods of tailings dam construction are reviewed and the advantages and disadvantages of each briefly discussed. Comparisons are made between the design and construction of conventional water supply dams and tailings dams. Examples are presented of some of the problems that may arise during construction and operation of a tailings dam. The paper also explains the need for basic instrumentation of tailings dams and for carrying out simple field tests and measurements during construction and operation. Of prime importance is the downstream monitoring of surface and subsurface seepage flows. These observations are invaluable where contamination of surface and/or subsurface water may become a contentious issue at some future date. Each tailings dam design must be based on a study of the particular requirements of that project. To make a proper evaluation, adequate data must be available concerning a large number of items•, including such things as: topography, hydrology, geology, subsoil properties, seismicity, government regulations, fineness of mill grind, mill water balance, availability of suitable construction materials, volume of water to be stored behind starter dam, downstream development or liability, and many others. The large number of variables involved in such an evaluation often result in the designer considering two or more alternative designs. Selection of the final design, which is usually based on detailed cost analyses of the alternatives, must be made in close consultation with the owner."

Jan 1, 1972

By J. D. Jones

Unique aspects of tailing pond design aid reclamation facilities for three separate projects are described.

Jan 1, 1978

By J. D. Jones

The geographic occurrence of economic mineral deposits presents a variety of problems in modern tailings disposal operations. This paper presents case histories in several sectors of the mineral industry as well as the several stages of operations planning required for new designs, system expansion, reactivation of abandoned systems and upgrading to present environmental standards.

Jan 1, 1978

By Heinz Distelmeier

Short Historical Review Tunnelling in Germany is as old as it is in other industrial countries. Until the middle of this century German contractors had no chance to work continuously in this business except if they were operating internationally. Since 1960, however, tunnelling has been a growing market domestically. The reasons for this growth have been both in the growing demand of traffic routes and also in an increasing environmental consciousness, which tries to transfer any cause of disturbance underground. Tunnelling engineers of course don't complain about this trend. As almost every German city is built upon water-bearing soft ground, shields have been used soon after they were first successfully utilized in Great Britain and the United States. Until the seventies lining systems for shield tunnels were predominantly either cast iron segments or concrete segments for primary support combined with different sealing systems and a secondary concrete lining cast-in-place. Steel ribs and timber lagging for primary support has not been utilized in Germany, since the owners don't accept timber to be left in the ground. In 1973, for the first time, permanent linings were constructed with watertight segment rings of precast concrete (Fig. 1). This lining was developed as an economical solution for use with slurry shields in noncohesive, water-bearing soils that required an immediately watertight lining. Extruded linings have a similar effect, although these still need a secondary lining

Jan 1, 1987

By J. Chae, D. Pecha, R. Andrews

The Henderson/ML King CSO Project is a major combined sewer overflow (CSO)reduction project for the Department of Natural Resources and Parks of King County, Washington. The central element of the project is the 3100 lineal feet long, 14'-8"diameter 42nd Ave S Storage/Treatment Tunnel. During the course of the project, the owner and consultants evaluated numerous elements of the tunnel including the alignment, geotechnical conditions, tunnel liner, and settlement monitoring requirements. The contractor utilized innovative shaft construction methods for the tunnel portals, and adhered to strict contract requirements in successfully constructing the tunnel. This paper provides an overview of the design and construction elements of the 42nd Ave S Storage/Treatment Tunnel that led to the successful completion of the project.

Jan 1, 2005

By Q Yang

This paper describes the design and construction of three 7.2 m span access ramp-tunnels to the three level underground car park of the newly redeveloped Top Ryde City Shopping Centre in northern Sydney. The tunnels were to be excavated without significant impact on the overlying Devlin Street, one of the busiest arterial roads in the Sydney metropolitan area and a major link in the Sydney road network. The interpretation of the geological conditions indicated that the tunnels would be driven in a formation of heavily jointed, extremely weathered to fresh Triassic Ashfield shale with some structural features such as dyke, fault and shear zones identified in the available boreholes logs. Both empirical and numerical methods were used to design the tunnels and to predict the ground surface settlements. The design solution, which was influenced by the relatively small scale nature of the work and the current demands on the tunnel construction market, included presupport, initial support and permanent steel fibre reinforced shotcrete (SFRS) lining. The interactions of the driven portals with cut and cover sections and the proposed deep excavation of the new shopping centre were considered at the design development stage and in the construction phase to ensure the safety of the live road. The tunnels have been successfully constructed and are now operational.

Mar 8, 2011

By A. C. Lyons

Foreword Sir William Halcrow and Partners are responsible for the design of the Ahmed Hamdi Tunnel as Sub-contractor to the Contractor, Osmac, a joint venture formed by the Arab Contractors, Osman Ahmed Osman and Company of Cairo, and Tarmac International of London. Throughout the paper the term "Client" refers to the Employer, the Ministry of Housing and Reconstruction, which latterly became the Ministry of Development and New Communities of the Arab Republic of Egypt. At the time of writing of this paper only a few hundred metres of the tunnel have been driven, but the design is substantially complete. Introduction The Ahmed Hamdi Tunnel, which is at present under construction, will be a two-lane tunnel crossing beneath the Suez Canal approximately 15 km north of the town of Suez at El Shallufa. It will become the first permanent connection across the Canal since 1967 and is visualised by the Egyptian Government as an early step in the development of the Sinai Desert along the eastern bank. The tunnel will carry pipelines for treated water and electric power cables to assist in this development. The tunnel, which will be 1640 m in length, is being driven through hard clay and mudstone using a tunnel shield fitted with hydraulic excavators. The primary lining is being constructed with precast, bolted reinforced concrete segments with an internal diameter of 10.4 m. The road deck structure and the walls of the air supply ducts beneath it are formed with precast, reinforced concrete units erected immediately behind the shield.

Jan 1, 1979

By Brian K. Ayres

Inco Limited, Ontario Division is currently in the process of decommissioning the Whistle Mine site located near Sudbury, Ontario, Canada. The most significant component of site decommissioning involved relocating approximately 6.4 million tonnes of acid-generating waste rock to the open pit from two adjacent stockpiles. An engineered cover system was designed for the backfilled pit to reduce the long-term production of acid rock drainage. Geochemical modelling was conducted to assess the effectiveness of various cover options on the longterm water quality of the backfilled pit. Results obtained from performance monitoring of cover system field trials at the site and estimated full-scale construction costs were used to select an appropriate material for the cover system barrier layer. The two-dimensional soil-atmosphere model VADOSE/W was used to develop a calibrated model of covered waste rock based on field data obtained from the cover trials, which was subsequently used to predict net percolation and oxygen ingress through various cover system alternatives for site-specific climate conditions. Erosion and landform evolution numerical modelling was completed to assist in designing the runoff management system and final landform for the pit cover system. The potential impact of various physical, chemical and biological processes on the sustainable performance of the pit cover system was also considered in the design process. This paper provides an overview of the design and construction of the backfilled pit cover system.

Apr 1, 2005

By Russel Delmar

Construction of Ontario Power Generation?s 12.8-m diameter, 10.4-km long water diversion tunnel in Niagara Falls, Ontario, is underway. The tunnel is being excavated by means of a 14.44-m diameter open gripper Tunnel Boring Machine. The tunnel lining is constructed as a two-pass system with the initial lining consisting of rock bolts, mesh, steel channels or ribs, and shotcrete, and the final lining consisting of pre-stressed cast-in-place concrete with a waterproof membrane. This paper describes salient design and construction aspects as follows: ? Regional and Site Geology ? Tunnel Layout and Design ? TBM Tunnelling and Cast-in-place Concrete Lining Construction

Jan 1, 2008

By James M. Tantalla, Dwight Metcalf, Roderic A. Ellman Jr.

"The construction of a new low head hydro-electric plant at the Cannelton Lock and Dam required the design and construction of a cofferdam to accommodate a deep excavation extending approximately 150 feet below the Ohio River levels. The new plant, which generates about 390 GWh of electricity annually, is owned by American Municipal Power (AMP). A specialist team was assembled to design and construct the cofferdam, marine dike and CB slurry wall that helped make the project successful and on time for project delivery.Because the new plant diverts water from the locks and dam through a powerhouse to generate power, it would need to be partially in the river to operate properly. To accomplish this, approximately 250,000 square feet of land was reclaimed from the river by construction of a marine dike. The dike, combined with the design and construction of a 150 foot deep cement bentonite (CB) cutoff wall enabled construction of the new plant in the dry. Extensive dewatering analyses were performed using Modflow to evaluate pumping requirements and the number of wells needed to maintain ground water at required levels within the side slopes and final subgrade. A monitoring program consisting of inclinometers, piezometers and movement monitoring points were used to monitor cofferdam stability and performance throughout construction. Detailed two and three dimensional stability analyses that included a parametric study of fluctuating river levels and slurry unit weight were performed to ensure stability and suitable low permeability of the trench during cut-off wall excavation both on land and in the marine dike. The wall was constructed with both a hydromill excavating primary panels and a clamshell following behind to construct secondary panels. Data acquisition systems onboard the excavating equipment allowed for detailed confirmation of the continuity of the wall at each interface between panels. Another challenging aspect was the CB mix design for the trench. The cofferdam required the construction of a 1,300-foot long marine dike downstream of the existing dam up to 100 feet tall founded on existing river sediment to enclose the site and cut-off the seepage into the excavation from the river. Marine dike construction utilized vibro-compaction to pre-densify granular fills placed underwater through which the CB trench extended."

Jan 1, 2016