Search Documents

FINAL REPORT OF' THE COMMITTEE OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS W. E. FOHL, Chairman J. W. PAUL J. M. RAYBURN C. A. WARNER JOHN B. CORRIN C. E. KREBS JOHN H. WILSON A. W. HESSE M. M. LEIGHTON H. I. SMITH [Accepted and Committee discharged with thanks, April 27, 1928.] Regulations recommended for the location, drilling, casing, protection, operation, plugging and filling, and abandonment of natural gas and petroleum wells; having for their objectives the protection of life and property by prevention of intrusions of oil and gas into workable coal beds, and the conservation of oil and gas resources in territory not underlain with workable coal beds. ARTICLE I DEFINITIONS SEC. 1. For the purpose of these regulations, definitions are as follows: Well.-A bore hole drilled for the purpose of developing natural gas or petroleum, or a bore hole producing natural gas or petroleum. Well Operator.-Any person, persons, firm, partnership, corporation, company or association that proposes to, or does drill, operate or abandon a well as herein defined. Coal Operator.-Any person, persons, firm, partnership, corporation, company or association that proposes to, or does operate a coal mine in territory known or reputed to be underlain with oil or gas-bearing strata. Coal Owner.-Any person, persons, firm, partnership, corporation, company or association, other than a Coal Operator as herein defined, that owns coal lands in territory known or reputed to be underlain with oil or gas-bearing strata. State Mining Department.-The duly constituted authorities of a state having jurisdiction over coal-mining operations, and oil and gas operations as herein provided. Plat.-A map, drawing or print made in accordance with the provisions of these regulations. Casing.-The pipe commonly used in wells drilled for natural gas and petroleum. Oil and Gas.-Synonyms, respectively, for Petroleum and Natural Gas.

Jan 1, 1928

By Richard J. Mainiero, James H. Rowland III, Marcia L. Harris

This paper reviews the potential hazards posed by the toxic fumes produced by detonating explosives in surface mining and construction operations. Blasting operations produce both toxic and nontoxic gaseous products; the toxic being mainly carbon monoxide (CO) and the oxides of nitrogen (NOx). The quantity of toxic gases produced by an explosive is affected by formulation, confinement, age of the explosive, and contamination of the explosive with water or drill cuttings, among others. Techniques to protect workers and the public from the potential hazards of explosive-related toxic fumes are discussed. These include: • Minimizing the quantity of toxic fumes produced. • Determining where the fumes may go so workers and neighbors can be moved out of harm’s way. • Preventing the fumes from moving towards workers and neighbors. • Monitoring the air near workers and neighbors so they can be relocated if fumes appear. • Ventilating structures or confined spaces until CO falls below a hazardous concentration.

By James Rowland, Marcia Harris, Richard Mainiero

This paper reviews the potential hazards posed by the toxic fumes produced by detonating explosives in surface mining and construction operations. Blasting operations produce both toxic and nontoxic gaseous products; the toxic being mainly carbon monoxide (CO) and the oxides of nitrogen (NO x ). The quantity of toxic gases produced by an explosive is affected by formulation, confinement, age of the explosive, and contamination of the explosive with water or drill cuttings, among others. Techniques to protect workers and the public from the potential hazards of explosive-related toxic fumes are discussed.

Jan 1, 2007

By Ray Brainard

Charleston Water System?s Daniel Island Extension Tunnel, initially thought to be the simplest of the four replacement tunnels to design and build, became the most challenging after the discovery of an unexpected 30-ft thick lens of sand in the normally consistent Cooper Marl while sinking a shaft on Daniel Island. This paper will explore the challenges involved with determining the extent of the unforeseen lens of sand, the accelerated boring program, and the redesign of the vertical alignment?keeping the alignment between the sand layer and the bottom of the Cooper River. It will describe how the challenges were overcome, and how the Owner, Engineer, and Contractor were able to team together to achieve the desired results.

By Ruediger Holz, Tommaso Settimo, Luciano Vignolo

Optimized CAPEX, OPEX, new products, yield and product quality in new process equipment as well as by upgrading of existing facilities are the key factors for success and profitable operation. For this, innovation in processes and design is crucial. Danieli can support their clients by offering innovative and well-thought-out process equipment and upgrade solutions. In 2018, Danieli has put into operation a complete cold processing complex in Turkey, which includes a new continuous pickling tandem mill featuring latest generation of market oriented technologies. In this line, dedicated to run a broad range of size and grades (IF to AHSS as DP1000), the highly efficient Turboflow® pickling process was selected. This technology already proved its efficiency and ability in former applications handling ultra-thin gauges at speeds even exceeding 400 m/min in the pickling tanks. The 5-stand 6-high OSRT tandem mill features important developments, like actuators to improve significantly strip flatness and a special air knife arrangement on the tandem mill exit side to generate perfect strip surface cleanliness. In galvanizing lines, the zinc pot is the most effective area to reduce costs in operation and consumables and increase the product quality. Danieli has spent significant efforts in developing most advanced technology for the wiping process. A fully integrated system solution has been designed to perform a wiping process with high quality, economy, accuracy and productivity. Center part is the newly developed X-Jet / Compact X-Jet air knife, added by new generation electromagnetic stabilizer as well as robotic systems to reduce human intervention and health risks in this area. This technological package is ideal also for upgrade of existing lines, typically generating a return of investment less than 1 year. On top, Danieli has developed advanced automation systems including L2 and L1 controls to achieve outstanding product performances.

Oct 1, 2019

By Luca Tommasi

Danieli complemented its wide range of production plants for the iron and steel industry with a further step upstream into iron ore pelletizing and beneficiation. Danieli has engineered and constructed a state of the art and fully automated pilot plant facility – pot grate and sinter box – at Altos Hornos de Mexico S.A. (AHMSA) Pelletizing Plant, Monclova, Mexico. Installation and commissioning were completed in October 2009. Key features of the pot grate include the avoidance of the need for operator intervention during the test, automatic system preheat, absence of dead time, heat recuperation system with an air/air heat exchanger, oxygen control in preheating and firing with zirconia oxygen analyzer, possibility to test deep beds up to 625 mm. A series of projects have been accomplished by AHMSA availing of the pot grate facility with the aim to enhance pellet plant productivity and to reduce operating costs. The results obtained by use of Danieli pot grate combined with the experience and skill of plant operators has shown significant technical and economical benefits thus fully justifying the initial investment made by AHMSA and confirming the importance of having an in-house testing facility in order to optimize industrial plant operations.

Aug 16, 2017

By Maurizio Massimo

Danieli developed the “3Q” suite of process control technologies to address three critical principles: delivering the highest product Quality, in the required Quantity, with Quickness of response required for today’s casting machines. Ever increasing market demands for productivity and slab quality necessitate the latest advances/improvements in equipment design, process technology, and control software for all types of slab casters, and Danieli boasts a unique experience that extends from ultra high-speed thin slab casters to extra high-thickness conventional slab casters. The “3Q” system is monitored and controlled by a unique, intelligent HMI incorporating. Touch screen technology and Operator Assistant tablets. Operator Assistant is a tablet based system that guides the operator through the plant process, so that in the event of a process change or an alarm the operator is automatically presented with the choice of possible solutions / actions. The comprehensive range of technological packages cover all aspects of caster design and automation control, from feeding of liquid steel into the tundish to the final slab leaving the caster.

Aug 17, 2017

By Uwe Wilhelm

Pittini Group has contracted Danieli in 2011 for the supply and replacement of the existing EAF at Ferriere Nord Plant in Osoppo. This was a very challenging project: giving the fact that the Meltshop was operating already under very high performance level, there were many elements involved for the project to improve (reduce the amount of charges, promote highest possible chemical energy utilization, allow best optimization on existing transformer power, modification on Drop Out box and Water Cooled Duct, Hydraulic System for EAF, Scrap Bucket design to fit to new EAF with existing loading and transport system, Automation System Review and Upgrade) as well as limitations of the existing installation (limited space, lifting capacity building and cranes and the required solutions for fast shell and roof exchange). All furnace parts, as well as installation engineering, were developed and discussed carefully with the Customer to either provide proven and reliable concepts, but also to define solutions for fast installation/maintenance access and quick exchange for offline turnaround. In the end, from disassembly of existing equipment up to the first heat of the new furnace, only 38 days were necessary. First heat was made on January 24th 2013, on the 6th production day 32 heats where produced at nominal design capacity and 28 days after start up 100,000 t liquid steel have already been produced.

Jul 30, 2018

By Andrea Donadon

This article introduces the Danieli Total Asset Management System, which involves 360 degrees service methods and equipment. Danieli Condition Monitoring System and Danieli Torque Monitoring System are fundamental to evaluate the conditions of the working components in heavy duty transmissions. The first one monitors the vibrations and the lubrication fluid conditions with the purpose to identify the presence of malfunctions, by detecting any variation of the signals from the standard values. The second one monitors the transmitted torque for each spindle and gearbox, with the aim of detecting any anomaly in torque distribution and magnitude, and evaluating the residual life of the mechanical parts, on the base of a dedicated fatigue damage algorithm. All these features are useful in avoiding serious damages to machines, facilities and people, but allow also planning the maintenance and overhaul activities with efficiency, in order to achieve the best plant availability and reliability. The data analysis is made by the IntelliCMS software, which interfaces with plant and Danieli operators and includes the possibility to cooperate by remote connections, simplifying service activities and support. All these features allow providing new full service programs, where the client is totally supported in maintenance, overhauls and substitutions. This is the best way to ensure the most efficient, high quality and reliable after sales assistance.

Aug 16, 2017

By Alessandro Pigani

Over the last 25 years the thin slab casting and rolling process has been gaining a major market share in the production of hot rolled strip, progressively eroding the areas previously of exclusive domain of conventional mills. This is mainly thanks to the competitiveness of the process over conventional ones, and to the growing ability of this technology to cover the majority of market niches, well beyond the boundaries of the commodity market. After having significantly contributed to the continuous expansion of this production mode and after an extensive campaign of theoretical research and physical testing in reference plants, Danieli has progressively developed over the years a new generation of thin slab casting and rolling layout, marking a new phase in the evolution of this process. The new step-ahead is epitomized by the name QSP-DUE. This configuration belongs to the Quality Strip Production (QSP) family, which is Danieli’s strip-quality-oriented thin slab based plants. The innovative features of the process are embodied in the acronym DUE, which stands for Danieli Universal Endless (Danieli patented technology – US patent n. 8087449, January 3rd, 2012). What makes this new concept different is the ability of “universal” rolling modes thanks to the fact that, now, within one single plant it is possible to perform coil-to-coil, semi-endless and endless rolling modes, making this plant a major technology innovation compared to the previous generation.

Aug 16, 2017

By Alim Ullah

Danieli entered into the Direct Reduction (DR) field in order to offer its clients complete turnkey facilities for steelmaking?from processing of raw materials through finished products. The Danarex® Process produces a passivated product, called the Supermetallic (SPM), without hot-briquetting. One of the main features of the Danarex® Process is its ability to produce approximately 50% of the Direct Reduced Iron (DRI) through reduction gas generated in a reformer and another 50% through recycling preheated furnace exit gas. Some other distinguishing features are: separation of carburising and cooling zones and the use of double bustle for better distribution of gas inside the shaft furnace. A pilot plant was set up at Hazen Research, Inc., Golden, CO in order to show that the integrated process works as expected and to obtain process data. The SPM obtained was of a very high quality, evidenced by metallization levels of 92% to 98%. The carbon content could be controlled between 1.5% to 4.0% by varying the operating conditions and approximately 75% of this carbon was present as Fe3C. The product was tested for inertness by Chilworth Technology, England, using UN standard tests and was found to be safe for outdoor storage and transportation.

May 1, 2003

By Nicola Santangelo

The current economic crisis and growing environmental issues have led the steel industry to face the simultaneous effects of low demand and production overcapacity in a globalized steel market, whilst confronting high energy prices and the need to comply with the green economy. Heat Recovery from waste gas of the Electric Arc Furnace (EAF) represents one of the greatest opportunities to reduce the consumption of primary energy and reduce the CO2 emissions in steel industry. The heat of the off-gas, if recovered and converted into electrical power, can make the whole Fumes Treatment Plant autonomous from the electric point of view, thus making it a “Zero-Energy FTP”. The concept is to substitute the Cooling Components (Water Cooled Panels and Air Cooler) are substituted with Heat Recovery Components (Hot Water Cooled Panels and Heat Exchanger). The recovered heat can be converted into power by using an Organic Rankine Cycle (ORC) turbine. The heat recovered by the HWCP and the Heat Exchanger is characterized by a variable thermal power, which affects the efficiency of the downstream ORC System. Danieli, in collaboration with the University of Udine, has developed the Thermal Stabilizer Unit (TSU). Danieli has realized the first step towards Zero Energy FTP at ABS steelmaking plant (Italy) by installing a CHR® - Clean Heat Recovery. This plant has been started up on 17th October 2014. The HMI of the CHR® is integrated in the HMI of the furnace, so all the process could be kept under control by the furnace operator. At ABS recovered thermal power reaches 5.5 MW. The max power production reached with CHR plant in ABS (over 1MW of electric power) consents an annual saving of approx. 500,000 EUR.

Aug 16, 2017

By Marco Quirion

The Daniel-Johnson dam, formerly named Manicouagan-5 (Manic-5), is located 800 km northeast of Montreal (Quebec) in Canada. This is the largest multiple-arch concrete dam in the world consisting in 13 arches and 14 buttresses. Since its construction in 1969, various type of cracks have appeared on both downstream and upstream faces of almost all the arches of this concrete dam. As a part of the Daniel- Johnson’s dam safety assessment program, Hydro-Québec is currently performing structural analysis of the dam with advanced numerical models to better understand and predict the dam behaviour. Because the buttresses transmit all the arch loads to the rock mass, determination of the properties of the dam foundation should not be neglected in dam global safety analysis and also to insure that reliable input parameters are used in the dam numerical simulations. This paper summarizes the past and the more recent investigations of this foundation used to assess its safety and stability. Moreover, the use of rock mass classification to estimate the deformation modulus, based on empirical equations, gives values in the range of 30 to 40 GPa that are higher than expected values. Using those values in the numerical simulations for dam structural analysis gives an excellent correlation with displacements monitoring of the buttresses.

Jan 1, 2015

By Roy Moreby

Dartbrook Coal is currently developing a modern, high production (3.5 Mtpy) single longwall retreat coal mine in the Upper Hunter Valley of NSW, Australia. The location is a green field site, with no surface or underground mining operations ever having taken place in the initial target seams. The coal seams of the working section, floor and immediate roof average a total 20 m in thickness and contain a mixed carbon dioxide 1 methane seam gas ranging from 6.5 to 11.0 m3/t. The target seams have undergone detailed characterisation to assess hazards and quantify the controls required to minimise associated risks during mining. Risks identified during initial phases of exploration and 14 months of development include: • High gas emission during development. • Probable high longwall gas emission rate. • Medium to high propensity to spontaneous combustion • Possible carbon dioxide outbursts on geological structures • The main controls currently in place include, • Mine geometry and ventilation circuits • Exploratory drilling ahead of development • Intensive in seam pre drainage • Goaf drainage plants • Comprehensive monitoring systems • Underground environmental management plan. • Pre mining predictions of gas emission provided an indication of gas emission rates which have proven to be an under estimate. Current mine issues are; • Both surface fans are at full capacity (250 m3/s 1.4 kPa) • Both gas drainage pumps are at full capacity (2.3 m3/s) • Alternatives to extensive in seam pre drainage being investigated (surface to in seam hydro fracture) Review of mine design underway This paper describes the seam characterisation, assessment of mining hazards and summary of the management plan developed to address the risks identified. A review of current mine underground environmental performance is also provided

Jan 1, 1997

Any project carries a number of challenges and risks. Inappropriate design, poor project management, time, industrial disputation and capital over runs are all areas which can impact on a project cash flows and return on investment. In the resource Industry you have the added complexity and risk of geology which is difficult to predict and sometimes unforgiving. The Dartbrook Mine was designed and constructed as a high output longwall mine and has overcome a number of hurdles to produce over 2.3 million tonnes for the first year of operation. A number of problems were encountered during construction which resulted in the inseam development being delayed for six months. Dartbrook people have demonstrated they can manage adversity and produce world class results. The mine has been through a very steep learning curve during 1997 and with this experience behind the mine is now producing at an annualised rate of 3.4 MTPA.

Jan 1, 1998

Dartbrook mine is a new greenfields thermal coal longwall mine located n the Upper Hunter Valley ten kilometres north of Muswellbrook Figure 1). Construction began in April 1993 with coal extraction starting n October 1994. Longwall production is scheduled to commence in the first quarter of 1996 with production expected to exceed 3.5 million onnes per annum. The permanent workforce will number 150 full-time ,mployees and productivity rates will be 22 000 per employee per annum m a ROM basis. Being a greenfield site Dartbrook has had the opportunity to develop and operate the mine using the best practices and latest technology available to meet high standards of safety, quality and production.

Jan 1, 1995

By Alexander Malahoff

An international research team working through the Hawai?i Undersea Research Laboratory (HURL) undertook a bold challenge to explore the chemistry, geology, mineral formation and superheated hydrothermal vents of the Kermadec Island Arc. With the mothership, R/V Ka?imikai-o-Kanaloa, scientists from six research institutions explored the active submarine volcanoes stretching over a line of volcanoes 1,000 miles long between Samoa and New Zealand. The expedition left Hawaii on the 18th of March 2005 and returned on the 5th of August having covered a distance of 10,000 miles between Hawaii and New Zealand. Scientists from the USA, New Zealand and Germany used the HURL submersibles, Pisces IV and Pisces V, as well as the remotely-operated vehicle RCV-150, aboard the R/V Ka?imikai-o-Kanaloa to dive into active volcanoes to water depths of 2,000 meters. Scientists from New Zealand, the USA and Germany conducted 41 dives on the previously unexplored (from manned submersibles) submarine volcanoes. Ten active volcanoes were explored during this time. Hundreds of specimens of new and unusual marine life, water chemistry, extremophile microorganisms, mineral formations and volcanic rocks were collected during this expedition with the two submersibles and the ROV. Bizarre natural events, such as the oozing of hot liquid sulfur from the ocean floor onto the skids of the submersible were observed. Carbon dioxide gas was observed profusely streaming into the seawater from the volcanoes, making these one of the greatest contributions to hot house gasses entering the atmosphere.

Jan 1, 2005

By D Bruce

OZ Minerals’ Carrapateena mine is a Sublevel cave mine located in South Australia, approximately 160 km north of the regional centre of Port Augusta. Carrapateena commenced underground development in 2016, with production commencing in 2019 and ramping up to 4.25 Mtpa by December 2020. In pursuit of continual improvement, the Carrapateena mining team sought to identify how it could better interrogate its current productivity levels and its drivers (root causes). During this process the team were confronted by a disconcerting number of different opinions (which often conflicted) on our actual productivity performance which led to a need for review. Although reliable data and a well-designed time utilisation model (TUM) existed, it was still unclear what actions needed to be put in place to improve productivity. This was for the following reasons: • Data sources were disparate unless significant effort was applied to compile them. • Data sources were not available in a format that could be easily viewed or analysed. • General understanding of the data which was collected and how it could be used was poor. • Process of regularly analysing performance and forming tangible actions to improve was lacking rigour. A project was then started with the goal to fix the areas stated above. An initial requirements gathering exercise was undertaken to identify key data sources for site which returned a staggering 42 known systems which were then shortlisted to the key systems that contained operational data and could generate tangible improvements when analysed. This paper discusses the approach to selecting the OZ Minerals Insights Hub as the chosen platform, and the effort and collaboration between cross-functional departments that was involved in transforming the data so it could be displayed in a useful way. The data sources identified included a fleet management system, two planning databases, a control system historian, and a mobile fleet machine data system. New processes were also introduced to digitally capture daily commentary; this was achieved utilising SharePoint Forms. Data pipelines were then developed in the Insights Hub platform to automate the ingestion and transformation of the raw mining data into curated data models for end user consumption. Tableau dashboard packages have been created to support facilitation of short interval control, daily review meetings, and weekly review meetings as well as data analysis of key equipment and locations. These dashboards visualise the mining data models in a form that provides the user a clear picture of what has occurred, why it has occurred, and where to focus improvement efforts. This has resulted in a team which is more accountable, more equipped to assess the root cause of performance, and more regularly able to make data driven decisions. The next step? To build this out from Mine to Mill and create a data indexing tool which will drive self-service reporting, a data agnostic platform and predictive tools that help our people continue to be one step in front.

Mar 29, 2023

By Howard Eavenson

The data given in the paper were collected to furnish an idea of the amount required in various operations of bituminous mining to produce a ton of coal, the plants selected being well-managed ones. With these are included some figures compiled from U. S. Coal Commission's report showing the average amount of labor in various classes of mines. THE information contained in the following paper was collected at the request of the U. S. Coal Commission, and is, published with the permission of that body and of the various companies furnishing the data. For obvious reasons, the names of the companies are not given. No data were gotten from States south of Virginia or west of the Mississippi River. The data about the amount of labor, in man-hours, required in producing a ton of bituminous coal have been collected with the idea of showing what is being done at some well-managed plants, and not to show the average amount required by all mines, which undoubtedly is considerably higher than the average of the figures shown.* Almost all of the figures were supplied by the various companies in reply to a questionnaire; when they were obtained from other sources the company was asked to verify them. On account of the amount of work required, the data were only requested for one or two months for each plant, and the figures represent in each case a month when the car supply was good and the work was practically steady. In the case of most of the West Virginia and Kentucky mines, these conditions were best met in May and June, 1922. The mines for which the figures are given are arranged by states and as to whether the mine operates under union or non-union or open-shop conditions. The union mines listed are generally considered to be as well-managed as are the non-union ones. The production per month in a few cases includes the amount of slate which is loaded and hauled out of the mine, as of course this requires nearly as much labor per ton as does the coal. These cases are noted:

Jan 1, 1924

The Olympic Dam Mining Operation involves the supply of some 2.2 million tonnes per annum of ore feed for the metallurgical plant. To achieve this approximately 9 km of tunnels are developed per year to gain access to the long hole open stopes that supply the majority of the production tonnes.Vast amounts of data are produced in the mining activity from the geology, mine design, scheduling, surveying, shift reporting through to the statistical reporting and analysis of the performance of the mine activities. Care must be taken when obtaining the data to maximise the usefulness of the data to other users so not to impose constraints or additional processes on future users.

Jan 1, 1992