Search Documents

By Roy H. Patten

When driving a shallow soft ground bore, the appearance of surface craters along the tunnel alinement indicates trouble, particularly when a major highway is intersected. During the excavation of a 3.7 m diam tunnel in Seattle, Washington a chemical grouting program was implemented to stabilize soil conditions sufficiently to allow advancement of the mole without loss of ground. Unanticipated mixed face conditions consisting of saturated running sand and some boulder pockets bedded on top of dense glacial till created excavation difficulties. A discussion of problems and corrective measures is presented.

Jan 1, 1987

By M. C. Rockwell

There are about 1.8 Mt (2 million st) of discarded dolomitic-limestone tailings from the Gays River lead/zinc mining operation in Nova Scotia currently stockpiled in a tailings pond at the mill site. Neutralization effectiveness similar to an agricultural grade limestone and low contents of residual metals make the tailings a potential source of soil conditioner material for the local market. However, the fine particle size, 98% passing 147 pm (about 100 mesh), and a moisture content of 20% make their handling, shipping, and application to soils difficult. The tailings were agglomerated into small hard pellets with various amounts of soil nutrients, moisture content less than 13%, and pH values ranging from 6.5 to 8.7.

Jan 1, 1987

By D. Hodouin

Abstract. Dynamic experiments were performed in a continuous open-circuit 40x40 cm ball mill using a pseudo-random binary sequence of the feed rate and measuring the variations of the discharge particle-size distribution. The impulse response is calculated by a cross-correlation technique. Then a model involving a discrete transfer function and a time-series stochastic equation is calibrated using maximum likelihood methods. Based on this empirical model. a minimum variance controller with constrained input is designed and its performances are compared. by simulation, to the performances of a conventional PID regulator.

Jan 1, 1987

By S. A. Kupferman

Cement raw materials used in southern California and Arizona cement plants occur in a wide variety of geologic environments. Limestone, the primary material making up 75-80% of the raw materials mix used in cement manufacture, is mined solely from Paleozoic Era deposits. During this time, 570-245 million years ago, vastly more limestone was formed in California and Arizona than at any other time (continent was in southern latitudes). The general geology of each limestone deposit associated with the eight southern California and two Arizona cement plants will be reviewed. Many of these deposits are geologically complex, having been subjected to Mesozoic deformation, metamorphism and instrusive events, along with Cenozoic uplift and deformation. All of the cement plants in this region require the use of secondary additives in order to meet the chemical requirements for cement. The kinds of additives vary greatly, depending upon the chemistry of the limestone deposit, cement specifications, and the cement manufacturing process. In some cases, clay deposits with suitable chemistry on or near the limestone sources are utilized. Where alkali limitations or need for alumina-rich materials exist, then specialty clay deposits are used. Iron-rich sources in the region include iron ore deposits and slag or mill scale from local steel mills. The geologic setting and location of these additives, along with gypsum and silica-rich deposits presently in use, will be mentioned.

Jan 1, 1987

By Peter J. Tarkoy

The use of personal computers (PCs) is increasing in underground construction applications, specifically, for estimating, record keeping, construction performance analysis, project cost reporting, and the effective application of construction experience for estimating and aggressive bidding. Applications particularly suited to the PC are analyses of construction performance and differing site condition claims. The advantages of using a PC in the analysis of differing site conditions claims is that the PC: requires quantitative and factual data, allows vast data manipulations, calculations, and sorting, and provides a simple graphic representation of complex data and issues. The restrictions imposed by a PC are conducive to the focus on essential facts, issues, quantitative analyses, and inherently, the truth. As computer thinking is established, a clearer, more precise and accurate focus on the elements of a differing site condition is essential for successful evaluation and presentation.

Jan 1, 1987

By Shigeru Nishitake

The Earth Pressure Balanced (EPB) shields designed by Mitsubishi Heavy Industries, Ltd., are recently more enthusiastically accepted by tunnel boring specialists. This company having built 1,000 tunnel shields utilizes its vast experience to resolve the problem to excavate through big boulders scattered in rather soft alluvial soil. Several types of EPB shields which can cope with large size boulders are described. Such shields are equipped with both drag bits and rolling disc cutters on the cutterheads. Previously removal of boulders has presented safety problems for workers while in the muck chamber, or venturing in front of the shield. This report describes the problem and how the equipment was modified to deal with the problem.

Jan 1, 1987

By Weibai Hu

Four methods to assess the relative flotability of fine coal have been tested: flotation with frother only, flotation with frother and collector, salt flotation, and timed-release analysis. A practical and simple criterion which combines the separation efficiency (capacity factor and kinetic rate constant (intensity factor) has been suggested. Five coal samples are chosen and tested. Based on test results, it is concluded that the flotability test with collector and frother is closer to practice, and, according to the suggested flotability criterion, coal fines can be classified into four categories of relative flotability: very easy, easy, moderate, and difficult.

Jan 1, 1987

By Balesh W. Konda, Andrew B. Cecala

Face ignitions occurring during longwall mining are increasing each year and are expected to continue to increase as deeper and gassier seams are mined. Effective methane monitoring strategies are needed to supplement techniques developed either to control the ignition sources or to dilute the gas to an acceptable concentration. Present monitoring strategies do not always detect dangerous concentrations as rapidly as they should. In a number of instances, dangerous concentrations have been observed at the shearer, but are diluted to acceptable levels when measured at the tailgate monitoring location. To effectively monitor and control methane concentrations, methane liberation and emission patterns must be identified. This need has led to a joint research effort between the Canada Centre for Mineral and Energy Technology and the United States Bureau of Mines. By combining the knowledge and experience of both organizations, the methane hazard facing underground longwall operations can be addressed more effectively. A comprehensive plan was developed to monitor methane levels throughout the panel and for an entire longwall mining cycle. In June-July 1986, a case study was performed at the Cape Breton Development Corporation's Lingan colliery in Sydney, Nova Scotia. This initial study was performed on two advancing longwall panels. Methane concentrations and flow patterns from this study are described in this report. A similar study is planned on a retreating longwall panel.

Jan 1, 1987

By G. R. Brunskill

The molybdenite flotation plant at the Magma Copper Co. San Manuel concentrator has been in operation since 1956. In January of 1980, the plant was converted from a hydrogen peroxide-ferrocyanide process to the current sodium cyanide-sodium hydro- sulfide process. This paper is an operational review of Magma Copper Co.'s molybdenite recovery circuit, column cell flotation experience, and use of on-stream X-ray fluorescence analysis.

Jan 1, 1987

By Birger Schmidt

INTRODUCTION Conceptual design of the first Exploratory Shaft (ES-I) for the Nuclear Waste Repository in Basalt (NWRB) began in July 1981; detailed design began in February 1982, and was largely completed by December (RKE/PB, 1983). The intent was to begin shaft construction by January 1983. The site had been prepared at that time, a construction manager selected and on board, the starter hole excavated and lined, and steel casings were under procurement. Government policy changed, however, and construction was halted before the drill rig started turning. Construction is now planned to begin in 1988. ES-I is a part of the site characterization program for the NWRB. The shaft will be used to develop production data and related information relative to drilling shafts at the site near Richland, WA, and to provide access to the repository horizon for site characterization and testing. The early program called for one shaft and some 330 m (1000 ft) of drifting. The program has since expanded to include a second shaft (ES-II) and more extensive drifting and testing. Currently, both shafts are planned to be 1.8 m (6 ft) in finished diameter, but studies are underway to determine if the second shaft should be larger. The drilling method was selected for shaft construction primarily because it offered a significantly shorter construction period than conventional shaft sinking using freezing and grouting. The finished drilled shaft will be lined with a continuous steel lining. Personnel are safer during construction with a drilled shaft than with a conventionally sunk shaft. The drilling method

Jan 1, 1987

By Ted H. Eyde

The Bowie chabazite deposit has yielded the most mined tonnage of any natural zeolite deposit in the United States. Since 1962 the deposit has yielded about 12,000 tons of crude chabazite, with an estimated market value of S30 million when sold as an activated molecular -sieve product. Between 1,000 and 1,500 tons of high-purity crude lump chabazite is now produced annually by stripping and selectively mining the lower, massive, half-foot-thick, "high-grade" bed. All of the chabazite is still shipped out of State for grinding prior to extrusion and activation. Zeolite minerals were discovered at the Bowie deposit in 1875, when Oscar Lowe identified a hydrous silicate related to chabazite or stilbite from a tuff bed that cropped out in the San Simon Valley. It was not until 1959, however, that chabzite, erionite, and clinoptilolite were positively identified as the principal constituents of an altered vitric-tuff horizon that crops out in the area originally described by Lowe. Shortly after the rediscovery of zeolite minerals in the San Simon Valley, several of the major producers of synthetic zeolites acquired land positions covering the outcrops, including projected extensions, and began exploration drilling. By 1980 all of the known chabazite reserves had been acquired by five companies and two individuals. The more than 3,000 holes drilled to explore the deposit and the excellent exposures provided by the strip-mined areas indicate that the chabazite-bearing horizon (known as the marker tuff) is confined to a flat-lying lacustrine section known to the operators as the Green Lake Beds. The deposition of the parent airborne vitric ash and subsequent zeolitic alteration was controlled by many factors, including the lake-bottom topography, depth and cation content of the saline-alkaline lake water, and proximity to post-depositional erosion surfaces. Zeolitic alteration was complete when an extensive system of younger paleochannels deeply eroded the Green Lake Beds. This left only a few erosional remnants of the marker tuff and the lower "high-grade-bed" that constitute the present deposit. Both the channel gravels and the Green Lake Beds are overlain by a section of halite-bearing brown mud-stones, known as the Brown Lake Beds. The bowie chabazite deposit can be used as a model to guide the exploration and development of other zeolite deposits that formed in saline-alkaline lacustrine environments.

Jan 1, 1987

By G. Avolio, M. Gilbert

INTRODUCTION The city of Alexandria, Egypt is located on the Mediterranean Sea at the northwestern edge of the Nile River delta. The city is approximately 26 km long and 3 km wide bounded by the sea to the north and Lake Maryut to the south. The Alexandria Project is split into 2 phases: phase one included designs to update two existing primary wastewater treatment plants, five pump stations and over 75 km of sewer pipe, 18 km o f which is tunneled, (1500mm to 2750mm ID pipe). Currently the pipeline and pump stations are under construction. Phase two of the project includes expanding both the capacity of the treatment plants and the limits of the collection system. Included in this system expansion is the 3.5 km long, 2250mm ID Central Zone Conveyance, which is the subject of this paper. The project is under the direction of The Alexandria General Organization for Sanitary Drainage (AGOSD). It is an USAID funded joint venture of two American firms, CH2M - Hill and Metcalf & Eddy who share equally the major portion of the work and two Egyptian firms, Engineering Consultants Group (ECG) and Wairth Associates who are also partners. The venture, which is both design and construction management, worked under the name Wastewater Consultants Group, WWCG. Michael Gilbert was Chief o f the Geotechnical Department and Project Engineer for the Central Zone Conveyance. Gennaro Avolio was Geotechnical Exploration Manager for the Alexandria Wastewater Project.

Jan 1, 1987

By W. R. Bull

This paper examines water-only cyclone performance for the cleaning of fine coal, and the effects of changes in feed flow rate, feed pulp density, and vortex finder diameter. A model is presented for performance simulation which can be used to predict products obtained based on feed washability data.

Jan 1, 1987

By S. R. Abt, J. D. Nelson, G. M. Smith

An empirical investigation was conducted to formulate a design criteria for predicting the beach profile of hydraulically deposited tailings. Field data were obtained from mining operations producing gold sulfides, silver, molybdenum, copper, platinum, and uranium. Site-specific parameters were collected that included the beach slopes, tailings soil properties, slurry properties, and the slurry distribution system characteristics. Each of the beach profiles were dimensionlessly plotted, and regression expressions were computed. It was determined that either a power expression or exponential expression closely predicted each beach slope. A general power expression and a general exponential ex¬pression were developed resulting in a design criteria. A procedure was formulated to determine which expression, power or exponential, is applicable to any specific site. A slope designation chart was developed as a function of the discharge, the tailings critical tractive shear stress, and the inertial forces exerted by the slurry on the beach.

Jan 1, 1987

By B. D. Nichols, W. S. Gregory

SOLA-DM is a three-dimensional finite-difference computer code designed to model the dynamics of an incompressible fluid and the transport of discrete particulate material around obstacles impervious to flow. The numerical methods used in this code are described. SOLA-DM was used to predict the particle flux sampled by the 10-mm Dorr-Oliver Cyclone and MINIRAM dust monitors. Various geometric and dynamic variations of monitor and airflow combinations were tested. The code predictions are shown in computer-generated graphic plots.

Jan 1, 1987

By N. S. Tanious

This work was completed prior to the author's appointment with the Nuclear Regulatory Commission (NRC). Therefore the views and conclusions contained in this paper are those of the author and should not be interpreted as necessarily representing the official policies or recommendations of the NRC. Reference to specific brands, instruments, or trade names is made to facilitate understanding and does not imply endorsement by the author or the NRC.

Jan 1, 1987

By Y. A. Attia

Auriferous sulfide ores often contain very finely disseminated gold and other precious metal particles inside the sulfide crystals. The encapsulation of precious metal particles gives rise to the refractory nature of such ores to current extraction methods. As a result, these fractions are frequently lost in the tailings. The purpose of this work was to investigate the feasibility of pretreating these refractory tailings with bioleaching before employing standard extraction techniques such as cyanidation. Leadville gold ore tailings containing auriferous pyrite were first concentrated by froth flotation. The pyrite concentrate was treated for different periods of time with 12 weeks adapted thiobacillus ferrooxidans before cyanide leaching. The bioleaching of the concentrate before cyanide leaching increased the gold extraction from 32% to 95% and that of silver from 48% to more than 98%.

Jan 1, 1987

By Robert M. Miller, Judy Milligan

A computerized "Decision Support System" was used to evaluate an "Underground Platform Approach to Oil Recovery". Over a billion calculations were required to model the mine layouts; learning curves for shaft, tunnel, and well drilling scenarios; detailed cost, schedule, and resource data; complex oil production and material balance data; varying reservoir parameters; and complex oil pricing curves. Simplified "optimum" solutions were defined in terms of muck hoisting capacity, barrels of oil per day, and present worth. Complex "optimum" solutions were defined in terms of minimal exposure scenarios during development followed by shortest time to full production.

Jan 1, 1987

By Bryce T. Tripp

Utah's abundant industrial rock-and-mineral resources support a relatively small but important sector of the State's economy. In 1983, six of the top 10 nonfuel mineral commodities (by value) were industrial commodities. Portland cement was ranked fourth, potash fifth, halite sixth, phosphate seventh, construction sand and gravel eighth, and lime tenth. Portland cement was produced by three operators, principally from the Jurassic Twin Creek Limestone. Potash was produced by three companies from Pennsylvanian beds in the Paradox Basin, surface brine of the Great Salt Lake, and subsurface brines of the Great Salt Lake Desert. Halite was produced by eight operators, primarily from surface brine of the Great Salt Lake. Additional production came from salt beds in the Jurassic Arapien Shale, solution mining of the Pennsylvanian Paradox Formation of the Hermosa Group, and subsurface brines of the Paradox Basin. Phosphate was mined by one company from the Permian Meade Peak Phosphatic Shale Member of the Park City Formation. Construction sand and gravel were produced by dozens of operators, primarily from Quaternary Lake Bonneville beach and nearshore deposits. Lime was produced by four operators from Paleozoic formations in the Basin and Range physiographic province of Utah. The future production of these and other industrial commodities, though individually uncertain, is expected to increase gradually as a group. Factors favorable for the future of the industrial commodities industry in Utah include large to almost unlimited resources for the major commodities, a healthy projected population growth, an abundant local supply of relatively inexpensive energy from coal and natural gas, and a favorable corporate tax structure and business climate.

Jan 1, 1987

By Roger S. Dewey

1.1. INTRODUCTION Despite indications of a general economic recovery in the U.S. during the mid-19801s, mine operators have not generally shared in the benefits of these reported better times. Budgets have not rebounded, borrowing is tougher, parent companies' pockets are not as deep as in previous years, and margins are not any better -- if there is any left over at all. Managing capital equipment budgets is always a challenge, and the last five years of stretched equipment lives make these decisions more tenuous. Delays and avoidance of replacements due to tough times inevitably makes those decisions increasingly difficult and usually more expensive The purposes of this paper are to present. a brief refresher outline of the fundamentals of equipment replacement analysis, to suggest a number of papers where analysis methods are explained in greater detail. and to recommend the use of a widespread microcomputer software capability (1-2-3) as the easiest path to a much-needed solution for a very difficult, and usually under-supported management decision problem 2. REPLACEMENT DECISION POLICY Investments in equipment replacements must compete for capital with all other investment alternatives. Capital for replacements of ten represents a greater commitment than do the new projects which a company might handle in a given year. But. sadly, formal policies for standardized analysis of replacements rarely exist, even in major companies. Yet this policy can be very significant in determining the competitiveness of a firm. Whereas many replacement decisions are based on cost minimization, economists and financial analysts agree that wealth maximization or return on investment is the superior criterion. Though the difference may seem slight, agreement on a firm's financial objective is vital. Replacement policy should be straight- forward. have a logical basis, and a proper level of sophistication. There are several reasons to develop a policy for replacement decision-making: [I] 1 - equipment's optimal economic life is nearly always shorter than its physical life; 2 - mine life often exceeds equipment life, so management must face these decisions routinly 3 - replacement capital costs, on an undiscounted basis, can run 25 to 75% of original capital 4 - technological changes may result in a newer machine or system which can operate more efficiently, more safely. or less expensively 5 - estimates should be made consistently in the fundamental areas of life expectancy, availability, utilization. price escalation, taxes 6 - long-term and short-term budgeting without decent data and analytical capability is nearly impossible, or at least ineffective Policy development assumptions which must be considered include: the planning horizon, cost patterns, interest rates, availability of capital, replacement vs. expansion, technology advances.

Jan 1, 1987