Search Documents

By E. S. Erickson, R. L. Stone

Introduction Evidence from blast furnace operations has indicated that using pellets with a higher ISO low temperature reducibility, a lower SiO2 content, and better resistance to low temperature degradation results in considerable coke savings and improved furnace operation. Although these benefits could not be directly related to reducibility differences alone, we believed there was sufficient evidence of the advantages in improved pellet reducibility to warrant laboratory investigation of ways and means to effect such improvements. It is well known that pellet reducibility can be significantly altered by changes in the basicity and the amount of non-iron oxide constituents. Past work (Friel and Erickson, 1980, 1982; Saeki et al., 1977; Thanning, 1974) has shown that with increased MgO contents, and at optimum CaO/S1O2 ratios, significant improvement in low temperature reducibility can be attained. The improved properties of such fluxed pellets have reportedly led to increased blast furnace efficiency and productivity (Saeki et al., 1977; Ilmoni, 1975). Less well known, however, is exactly what factors control reducibility in acid pellets. Because of this gap in knowledge, studies were undertaken of the factors affecting reducibility in acid pellets and to estimate their relative significances in modifying reduction behavior. This paper describes that part of our work done to determine the effect of bentonite on reduction behavior. Our approach was to first examine the effect of bentonite's presence on as pure an iron oxide as possible (i.e., a magnetite "superconcentrate" containing about 0.2% SiO2) so as to eliminate any gangue-binder interaction. The next step was to look at bentonite effects on concentrates with only limited amounts of gangue (containing about 1% SiO2), but of two different types, simple and complex silicates. Last, we

Jan 1, 1988

By D. W. Horsfall

The different types of processes used in fine coal beneficiation in the Republic of South Africa are listed, together with data giving an indication of their separating efficiencies The two classes of coal, fines and ultra-fines, present in the -0,s m fraction of the run of mine coal are discussed, with special reference to their beneficiation characteristics. Using those properties, together with the data on plant efficiency, case studies are worked out to indicate the advantages and disadvantages of the different processing routes available. The paper closes with an indication of areas where research is required to enable some of the processes to be applied to a greater extent than is presently the case.

Jan 1, 1988

By S. Vijayan

Despite the limited demand for rare-earth elements, as well as yttrium and scandium, in conventional applications, the emergence of ne~ high-technology applications such as supermagnets, lasers and superconductors is expected to result in significant demand for some of these elements. This paper examines the anticipated applications and demands for rare-earth elements over the next decade and their implications on the utilization of available resources. Process methods for the recovery of rare-earth elements from conventional and unconventional resources are reviewed in the context of their growing demand. Challenges facing the industries in meeting this opportunity are also discussed.

Jan 1, 1988

By M. E. Gershon

Software for coal blending has gained a lot of recent attention as micro-computer programs have come on the market. Some of this software is appropriate and some is not. This paper looks at the types of models being used and points out the strengths and weaknesses of each. Recommendations are then made concerning the level of detail required for these programs, relating this concern to the various ways in which coal companies are using these programs. A checklist of company requirements for these programs and available pro-gram-features provides an aid in matching the program to the company.

Jan 1, 1988

By David S. Bolin, Gary R. Peterson

INTRODUCTION In both the United States and Canada, a company making a public offering of securities must comply with regulations which have been promulgated by Federal and/or Provincial Legislatures. This paper focuses on the regulations pertaining to reserve reports required by the United States Securities and Exchange Commission (SEC). SEC RESERVE FILINGS Reserve reports made to the United States Securities and Exchange Commission are the only reserve reports which are directly regulated by the United States government. The requirements for SEC reserve reports are set forth in the filing forms as shown in Appendix A, from Item 17A of SEC Form S-18. These reporting requirements, which are intended to protect the investing public from inaccurate or misleading claims, are primarily oriented to S-1 or other filings for new stock issues but must also be followed for annual 10K reports which must be filed annually by U.S. public corporations as part of the Corporate Annual Report. These undertakings require independent audits of reserves, mine designs, plant facilities and a general economic evaluation of the planned or existing operation as part of the backup documents for filing. An ore reserve is defined by the SEC as "That part of a mineral deposit which could be economically and legally extracted or produced at the time of the reserve determination". This definition is unchanged since it was last

Jan 1, 1988

By C. J. Konya

When blasts are designed, the assumption is made that all blastholes release near ideal energy. In many types of mining operations, some blastholes release very little useful energy. These blastholes will be called malfunctioning blastholes. Recent studies indicate that on many types of blasting applications, 30 percent of blastholes are malfunctioning. This malfunctioning routinely occurs on the operation and is not an unusual occurrence. This paper will discuss the cause of malfunctioning blastholes and methods to minimize the detrimental effect on both safety and costs.

Jan 1, 1988

By R. L. Pozzo

The electrochemical nature of mineral-grinding media interaction in the wet grinding of one and two sulfide mineral ores was investigated with regard to the flotation behaviors of the minerals. Two iron sulfides (pyrite and pyrrhotite) and mild steel were used to represent the sulfide minerals and the grinding media, respectively. Galvanic currents in two-and three-electrode combinations under abrasive and non-abrasive conditions were correlated with the floatabilities of these minerals under corresponding conditions.

Jan 1, 1988

By L. B. Anderson, G. A. Carmody

We wish to comment on the paper by G.W. Heunisch (MINING ENGINEERING, January 1987), which raised several important points regarding treatment of acidic waste waters. This paper confirms, in part, tests carried out by Allyn Corp. Allyn is the manufacturer of the proprietary product Alka-Ment, one of the materials that Heunisch tested. The first point is the extreme sensitivity of the sedimentation rate on the nature of the treatment material used. This apparently results from differences in nucleation of the metal hydroxides, and is consistently higher for Alka-Ment. This decreased sludge volume is also observed when Alka-Ment is combined with flocculants, such as organic polymers (see Table 1). Our second point is to emphasize that Heunisch's work shows how dependent the sludge volume is on pH. It is common practice to overtreat AMD by raising pH to 9 or 10. This practice, in addition to being wasteful of material, actually decreases the density of the resulting sludge, probably by creating charged particles that do not readily coalesce. When treating with Alka-Ment, we recommend that the treatment be monitored by testing both pH and dissolved iron. For both tests, it is important to allow adequate time to elapse between treatment and measurement, so that dissolution of alkali, aerobic oxidation of iron, and precipitation of the metal hydroxides are nearly complete. Our tests have indicated that from 30 minutes to one hour is commonly required. Only in this way can a minimum pH be attained, with adequate treatment, denser sludge, and lower treatment rates achieved. Thirdly, Heunisch correctly recognizes that ASTM titration of Alka-Ment does not reflect the true treatment value available in a unit of Alka-Ment. Our work at Allyn indicates this is a most important consideration when evaluating various materials for the treatment of acidic waste waters. While we were unaware of Mr. Heunisch's work, we welcome comparisons between Alka-Ment and any competitive products readily available for field use. Allyn has hundreds of hours of laboratory and field data we are ready to share with interested parties treating acidic waste water.

Jan 1, 1988

By Y. Ye, J. D. Miller, E. Pacquet, S. Gopalakrishnan

From laboratory research activities during the past five years, it is now evident that effective flotation separations can be achieved with the high-capacity air-sparged hydrocyclone. The effectiveness of the equipment has been demonstrated on a pilot-scale basis (1 tph) for a number of mineral commodities including coal, copper, gold, and industrial minerals using a nominal 5-cm x 50-cm system with separation efficiencies equivalent to those achieved by conventional flotation machines. The high specific capacity of the air-sparged hydrocyclone (100 to 600 tpd per cubic foot of cell volume for a nominal 5 cm x 50 cm system compared to 1 to 2 tpd per cubic foot of cell volume for conventional columns and mechanical machines) makes it especially well-suited for the pro- cessing of low-grade ore. As a result of these pilot-scale successes, a number of plant-scale test programs are planned for larger-diameter units to establish wear characteristics and scale-up relationships for design purposes. The status of the air-sparged hydrocyclone technology is reviewed in the present paper, including a description of the system, fundamental considerations of flotation mechanisms, general discussion regarding the effect of control variables, and the significance of feed characteristics.

Jan 1, 1988

By Debra W. Struhsacker, Jean Kiel, Jeffrey Thatcher

3.1 INTRODUCTION As heap leach precious metal projects become increasingly common in the United States, federal, state and local regulatory agencies are beginning to take a closer look at the short- and long-term environmental consequences of this recovery technology. From an operator's point of view, there is seemingly a confusing regulatory maze to be navigated and a plethora of permits and approvals to be obtained prior to commissioning a heap leach operation. The degree of difficulty associated with obtaining permits for a heap leach project depends largely upon the state in which the project is located. Permit acquisition is generally easiest in those states most familiar with heap leaching technology. For example, heap leaching is well understood in Nevada, and heap leach operations are relatively easy to permit, although permitting conditions in Nevada have recently become more stringent. However, many states are just beginning to become familiar with heap leach operations. Many of these states such as Idaho, Colorado, South Dakota, Oregon, Montana, Washington and South Carolina are in the process of drafting regulations and establishing guidelines for heap leach projects. In most cases, these regulations specify design and operating criteria as well as reclamation and decommissioning procedures. This chapter provides an overview of the regulatory and permitting aspects of heap leach operations. Permitting requirements for projects developed on federal land are discussed in detail. 'The state and local regulatory atmosphere and permitting requirements for various states are also presented. The chapter concludes with a generic permitting strategy. 3.2 KEY ENVIRONMENTAL CONCERNS The primary concern of most local, state, and federal regulatory agencies is the use, storage and transport of sodium cyanide (NaCn), and potential cyanide contamination of surface and groundwater resources. The toxicity of cyanide to people, fish and wildlife is also an important issue. Unfortunately, in the public eye, cyanide heap leaching has some emotional impacts similar to those associated with radioactivity and uranium mining. This perception and the general lack of understanding of cyanide can lead to unnecessary concern about cyanide contamination, further complicating the regulatory environment.

Jan 1, 1988

By D. Olsen

The paper discusses the legislative and practical approach adopted to problems of management of environment in relation to coal mining in a very sensitive area of the south coast of New South Wales. The environmental problems are complicated in this area due to multiple and very often conflicting land usages. The environmental approach in relation to water quality maintenance, noise control and air quality is discussed and methods adopted meet stringent requirements. Requirements of New South Wales Regulations on Environmental Impact Statements (EIS) are described.

Jan 1, 1988

By J. D. McKendrick

Alaska's Arctic Slope lies between the Brooks Range and Beaufort Sea and is a region about the size of Nebraska. It has some of Alaska's richest hydrocarbon deposits. In addition to containing petroleum and natural gas. Much of the area west from the Colville River has low-sulfur coal deposits which are shallow enough for surface mining. Developing those resources will require a firm and realistic' commitment to protecting and rehabilitating the natural habitats. Balancing such a commitment with economic constraints in a practical sense requires knowledge of the environment and its associated biological components, i.e. the soil/water-plant-animal relationships.

Jan 1, 1988

By W. J. Halvorsen

Means for minimizing the disadvantages of thermal drying are suggested. The other ap¬proach of substituting other techniques in place of thermal drying is also discussed. Recent devel¬opments in fine coal screening dry down to 3.2 mm (0.125 in.) and 2.0 mm (10 mesh) offer an econom¬ical means in certain cases.

Jan 1, 1988

By D. C. Moore

The decision to proceed on a "fast track" construction project is not" without risks as well as rewards. An understanding of some of the risks prior to start of the project will maximize the rewards. This paper describes the research, development, procurement, engineering and construction of the Asamera Minerals cannon Mine concentrator. This fast track project was accomplished in 20 months. Special attention is paid to the risks encountered and the steps taken to ameliorate them.

Jan 1, 1988

By J. M. Keane, C. K. Chase

Critical to successful dump and heap leaching of copper is an adequate evaluation of applicable parameters. This paper deals with methods to establish optimum conditions for dump and heap leaching copper so that commercial operations can proceed. Discussion is also offered of ore occurrences and preparations for dump or heap leaching.

Jan 1, 1988

By John B. Sabey, Vernon R. Degner

The industrial coal processing trend toward greater fines production, due to mining techniques and customer requirements for reduced ash and sulphur content in the fine coal product, is the basis for ongoing efforts to improve the performance of the flotation machine. WCO has successfully adapted the principles of the beds Column to a full size machine prototype. Recent plant evaluation tests confirmed the initial promise of this concept by achieving a considerably lower ash product while maintaining the combustible recovery level of conventional flotation machinery. The paper will include a review of the fundamental principles of the beds Column concept, together with a summary of the WEMCO R&D Program from concept evaluation and laboratory testing, through pilot, to full size machine tests. The performance of the WEMCO/Leeds flotation column will be compared to conventional flotation concepts using a flotation "kinetics" approach, which quantifies the floatable and non-floatable specie recovery performance using the Klimpel model as the basis for analysis. The variety of distinct features unique to this concept include a series of barrier rods which are used to advantage, often together with countercurrent reflux water flow, to achieve a significant improvement in product grade. The hydrodynamics associated with the mechanics of "gangue stripping" from the rising "air bubble-floatable specie" matrix will be briefly reviewed.

Jan 1, 1988

By O. Olajide, E. H. Cho

A laboratory study of the jigging process with Pittsburgh seam coal has been conducted. The laboratory-scale Baum jig used in this study was a McNally-Norton LO30X Right Hand Model Baum jig with an effective screen area of 0.186 m2 Feed material was prepared by selecting a size range from 6 mesh to 1.91 cm. Solid feed rates were 27.2 kg/min and 32.7 kg/min. Water flow rates were varied from 37.9 to 94.6 L/min. It has been found that smaller particles give higher values of density of separation and lower efficiency of separation. Increasing water flow rate increases the discharge rate of clean coal at a constant solid feed rate. It appears that the efficiency of separation increases by increasing water flow rate up to a certain value, and then levels off upon increasing the flow rate further.

Jan 1, 1988

By Daniel J. Brunner

The U. S. Department of Energy (D.O.E.) requires that the prospective nuclear waste repository in Basalt at Hanford, Washington, comply with State of California mine and tunnel safety orders. These regulations require that all main fans be installed in such a manner as to permit prompt reversal of airflow. This paper evaluates the requirement of air reversal and the appropriateness of imposing such regulations on the proposed nuclear waste repository in Basalt.

Jan 1, 1988

By Guoming Liu, Weibai Hu

The designing aspects of column profile, cross-section and height, types of aerator or air sparger, and feeding and discharging devices have been designed and tested. In operating aspects, the flotation column: has beer, compared with the conventional mechanical flotation machine in large- scale plant practice. It has been found that the reagent conditioning time and the slurry residence time required in the column are longer than those in the mechanical flotation machine. The general opinion is that the flotation column can show some effectiveness in specific cases as long as it is properly designed and carefully controlled.

Jan 1, 1988

By Ralph E. Weeks

Utilization of true in situ technologies for mining copper in Arizona will involve a complex environmental permitting process. This process is a key factor in determining the feasibility, costs, and implementing time frames required for development of this innovative mining method. The regulatory structure in Arizona is presently changing due to enactment of the Environmental Quality Act (EQA) of 1986 and development of new aquifer protection rules and regulations. The Bureau of Mines has reviewed the comprehensive hydrogeologic characterization, ground water monitoring, mechanical integrity testing, well construction, contingency planning, and other regulatory elements that will serve as mechanisms to assure protection of ground water resources. The purpose of this paper is to inform the domestic copper industry of the significance of the new Arizona regulatory structure and its implications for prospective in situ operators.

Jan 1, 1988