Search Documents

By D. C. White

The Vulture Mine near Wickenburg, Arizona was a major gold producer from 1863 to 1942, having yielded about 11,000 kg Au and 8,000 kg Ag. Gold occurs as coarse native metal and electrum in quartz veins and also finely disseminated within a quartz monzonite sill and its silicified wall rock. The sill is semi-conformable within a Proterozoic volcaniclastic-dominated sequence all dipping north about 35°. Early mining focused on the vein-hosted gold particularly in the immediate hanging wall and footwall of the sill. Later efforts included some open-pitting of the outcropping sill and adjacent altered and mineralized rock. Two sets of post-mineral faults have complicated the orebody geometry.

Jan 1, 1988

By G. J. Schneider

The higher stress zone adjacent to an underground opening causes a velocity anomaly that can be mapped in favorable conditions with an acoustic cross-borehole logging system. Bureau personnel used a specialized system at the Colorado School of Mines test site near Idaho Springs, Colorado, to locate the Edgar Mine tunnel and its associated stress anomaly. Data from the logging system' were processed with a tomographic image reconstruction algorithm to map the opening and the location of the high velocity zone around the opening. The velocity imagery from tomographic analysis compared favorably with predictions from numerical modelling of the location of the stress anomaly.

Jan 1, 1988

By S. Bhattacharya, M. M. Singh

The Surface Mining Control and Reclamation Act of 1977 (SMCRA) requires under-ground coal mine operations to prevent "material damage" to renewable resource lands caused by subsidence. However, what constitutes material damage is not defined. This paper discusses the applicable criteria for agricultural lands, forests and grazing lands, surface water bodies, and ground water aquifers. Although data on the subject are limited, an attempt is made to present quantitative guidelines to distinguish between moderate and severe damage due to subsidence.

Jan 1, 1988

By D. F. Watson, G. M. Philip

The article cited above reflects the difficulty that is often encountered in interpreting different aspects of kriging. Baafi et al. write: "Due to negative kriging weights, negative block grades may be obtained in some extreme situations, which makes no practical sense." Their solution to this particular problem is to constrain the kriged estimates to data values that have positive weights, i.e., reduce the subset size contributing to the estimation. As Journel (1986, p. 133) has already observed, "Negative weights are no evil." Indeed, they are an ineluctable result of the Lagrangian multipliers in the system of simultaneous equations. The fact that data distant from the estimation point may be given negative weights simply means that the influence of such distant values must be negated because their influence is contradictory to closer values (as illustrated by Baafi et al. in their Figs. 3 and 4). Of course negative kriging weights applied to distant grade values will not in themselves induce negative grade at some central interpolation point. Negative grade values, rather, seem to be a particular artifact of automatic methods of estimation involving accumulations (Philip and Watson, 1985a, 1985b, 1987b). The elimination of negative weights, suggested by Baafi et al., is likely to exacerbate a quite different problem of kriging and piecewise spline interpolation discussed elsewhere (Philip and Watson, 1987a). In interpolating large data sets of scattered observations, changing local subsets or neighborhoods must be selected automatically. Because of the mathematical formulation of kriging and spline interpolation, discontinuities then occur between closely-spaced estimation points as the subset used in the estimation changes. If this subset is reduced in number and size, the discontinuities will be amplified and more common.

Jan 1, 1988

By C. J. Johnson

As the U.S. coal industry moves into the next century, it is becoming more apparent that the effective application of new technology is the only way it can remain competitive in the energy marketplace. Examples of this emphasis are with us today in such diverse areas as face-ventilation and excavation-equipment applications. The focus of this new technology is directed toward improvements in health and safety, cost control, and productivity. Room-and-pillar mining accounts for approximately 80% of the nation's underground coal production; this percentage is not expected to decrease markedly in the near future. As such, this paper analyzes the impacts of the changing technological climate on future room-and-pillar operations by comparing a base-case section (current) to three scenarios incorporating new or emerging technology. A microcomputer-based comparative analysis will reflect the changes in section production and costs.

Jan 1, 1988

By M. Sengupta

Vast reserves of oil shale occur in the Green River formation in Colorado, Utah, and Wyoming. The room-and-pillar mining method is applied to flat-lying sedimentary deposits. Important elements in mine design include mine orientation, vertical location of the mining zone, selection of roof horizons, room span and pillar size, barrier pillar size, panel dimension, and layout of mains and submains.

Jan 1, 1988

By S. D. Thompson, L. Adler

This study reviews and analyzes the empirical methods available for designing the capacities of coal mine gathering belts. The analyses lead to recommendations concerning the application and implementation of each empirical method. Operations research techniques, mainly simulation models, are also briefly mentioned, and a few recommendations are made concerning their selection and application. The objective of the study is to provide a reliable basis for the practicing engineer to properly select, apply, and implement a capacity design method.

Jan 1, 1988

By G. Danko

Ventilation and refrigeration for mine climate modification, contributes significantly to the operating costs of a deep hot mine. Mine climate simulation programs can be used to minimize the impact of these costs. There are several computer codes available including CLIMSIM?, to assist in this work. Whichever simulation program is used, it is the mine ventilation engineer who must supply the input data. This paper raises and answers the following question, namely: what accuracy is required of the basic input parameters, in order for a certain precision to be obtained in the predicted air temperatures? In the first part of the paper a new approach is described to estimate the dry and wet bulb temperature of the airflow, either in a dry or wet roadway. The calculation procedure allows an arbitrary temperature change with time, using Duhamel's superposition solution. Matrix-vector representation is applied to simplify the computational structure. In the second part of the paper the sensitivities of the dry and wet bulb air temperatures are analyzed to the changes of the rock thermo-physical properties, the heat transfer coefficient and the wetness factor.

Jan 1, 1988

By D. H. Davidson

In situ leaching (ISL) of copper has the potential of reducing both capital and operating costs for copper production. The ISL process combines surface facility (SX/EW) and wellfield operations, each of which must process the same total flow rate and pregnant liquor copper concentration. Commercial cost data are only available for SX/EW facilities. This paper discusses: the interaction between the principal wellfield costs associated with well modules, and wellfield start?up with SX/EW costs; how to estimate what the level of wellfield costs must be to optimize DCF/ROR; and how to relate these wellfield costs to orebody geologic and mineralogic characteristics.

Jan 1, 1988

By Robert G. Moorhead

Fine-coal screening can be one of the most critical operations in a modern coal-cleaning plant. The yield and quality of clean coal produced in fine-coal circuits is controlled as much by how efficiently 0.15 mm (100 mesh) particles are sized as on the performance traits of the fine-coal cleaning device itself. In addition, the increased interest in effective fine-coal sizing operations indicates that many operators have also discovered its importance in affecting the quality and yield of clean coal produced in fine-coal circuits. This paper describes the three most prevalently used fine-coal screening technologies and discusses their sizing mechanism, performance, and application.

Jan 1, 1988

By Arol, A. I., I. Iwasaki

The presence of calcium ion in iron ore pulps causes heterocoagulation of rnontmorillonite on hematite leading to indiscriminate dispersion. Two methods were investigated to control the adverse effect of montmorillonite: a chemical method using such complexing agents as EDTA and sodium tripoly- phosphate, and a mechanical method involving ultra- sonic treatment. Their roles in controlling the adverse effect were investigated by zeta potential measurements, starch adsorption tests, and flocculation and selective flocculation tests.

Jan 1, 1988

By A. L. Wilder

Coeur d'Alene Mines Corporation's newest precious metals property is located in the old Rochester Mining District approximately twenty-five miles northeast of Lovelock, Nevada. Built at an elevation in excess of 6 000 feet, the Coeur-Rochester gold silver heap leach property encountered cold weather operational problems typical of most northern Nevada heap leach properties, soon after the start-up of operations last fall. Due to the size of the heap area under leach at Rochester, it was decided that 1 the usual practice of spraying to an "ice field" and waiting for the spring thaw was impractical. Further, the delivery schedule for a solution heating system of the size required was unacceptable. Accordingly, Rochester personnel embarked on a program to seek out a leach solution distribution system that would enable an operation through the winter and yet be cost effective. The findings of this program were rather dramatic and, as a result, the whole perception of heap leach solution application at Rochester has changed forever.

Jan 1, 1988

By Andrew F. McKown, Lewis L. Oriard

Advances in explosives engineering are moving forward in several different aspects. These include improvements and new development in explosives products, the application of these products to blasting technologies, and the study of the peripheral effects of the use of explosives, such as ground vibrations and airblast. Topics of special interest in the last several years include new explosives and detonators, cap timing, explosive casting, high-speed photography, perimeter and slope control, air decking and mathematical modeling of blasting processes.

Jan 1, 1988

By Y. H. Kim

A simulation procedure has been developed that realistically portrays aggregate growth and disintegration for particular types of floc structures in water and wastewater treatment processes. The procedure requires local dissipation rates and specification of an interaction distance between colliding particles. A principal difficulty encountered in polymer flocculation, however, arises from changes in conformation of adsorbed macromolecules. Therefore, in systems where polymer flocculation occurs by bridging, dynamic changes in the particle size distribution depend upon the interaction of nonlinear. stochastic hydrodynamics with particles whose growth results from a number of concurrent and sequential random processes.

Jan 1, 1988

By K. H. Lee

The rate of beryllium dissolution from a low-grade ore was studied in sulfuric acid solutions. The effect of stirring speed, sulfuric acid concentration, particle size and temperature on the rate of dissolution of beryllium was established. The results of the study showed that the dissolution rate is independent of stirring speed within the range of 250-1000 rpm but depends on 1/2 power of the sulfuric acid concentration. The dissolution rate increases exponentially with decrease in particle size and the maximum attainable rate of extraction with respect to particle size is 6.6 x 10 mol dm min. The apparent activation energy (^E) for the dissolution reaction is 54.4 kJ/mol (13.0 kcal/mol). Based on this magnitude of the activation energy, it is concluded that a surface chemical reaction is the rate limiting step for the temperature range (70° -100°C) investigated.

Jan 1, 1988

By M. M. Nash

Since the late 19th Century, scholars have been concerned about finding proper methods of managing business. The search seems to be taking us full-circle to the time and motion studies of Taylor (Horn, 1987). It wasn't until the late 1970's, however, that systematic investigations were made in the mining industry. One of the first was a study by Sanders, Patterson, and Peay (1976). That project explored the relationship of attitudes and safety. Peay, Atkin, and Goodman (1977, then reviewed the whole area of Organizational Development, including the so-called Rushton experiment.

Jan 1, 1988

By J. E. Rourke, O&apos

This paper describes the use of rock index property testing to obtain rock properties that a.re useful in the design and construction planning of an underground development for civil engineering or mining projects. The index properties discussed include (1) point load; (2) Schmidt hammer hardness; (3) abrasion hardness; and (4) total hardness. The first two index properties correlate to uniaxial compressive strength and Young's modulus. Discussions are given on the relationship to rock mass properties and the integrated use with semi-empirical, geotechnical design methods. The latter two properties correlate to construction performance parameters and some experience is cited. Examples of data are presented from an index testing program carried out on siltstone, sandstone and limestone rock core samples from a deep borehole drilled in the Paradox Basin of Utah for a nuclear waste repository site investigation.

Jan 1, 1988

By C. I. Wilmot

FMC's Paradise Peak Mine was discovered in July 1983. The deposit at discovery contained 11,340 ,000 tonnes (12,500,000 tons) of ore grading 3.71 glt (0.108 oz/ton) Au and 120 glt (3.5 oz/ton) Ag. A feasibility study was completed by Davy McKee in May 1984, with detailed engineering starting in June 1984. Construction of the facility started on January 2, 1985 with plant start-up taking place on April 14, 1986, two and one half months ahead of schedule and more than 10% under budget. This paper describes the status of the operation approximately 1-1/2 years after start-up including revisions and additions to equipment and process.

Jan 1, 1988

By L. Xiao

Using K-oleate as a collector and alizarin red S (ARS) as a modifying agent, selective depression of dolomite from francolite was achieved in alkaline medium (pH> 9.0). Interestingly. ARS was also found to depress igneous apatite in alkaline medium in oleate flotation of apatite and calcite. Adsorption of ARS alone on dolomite was found to be higher than that on francolite. Complimentary adsorption experiments of ARS and K-oleate showed that oleate adsorption was increased in the presence of ARS on francolite but not on dolomite. K-oleate adsorbs on both francolite and dolomite and causes precipitation of calcium and magnesium oleate. Such precipitates can be pre-vented when ARS is present. The results are explained in terms of competitive adsorption for the active sites on francolite and dolomite by oleate and ARS, and their interactions with dis-solved mineral species in solution.

Jan 1, 1988

Research has determined that ground control interaction problems in mining over a previously mined seam occur primarily in the tension zone created at the edge of the subsidence trough, and in areas above lower seam remnant pillars. Based on empirical and analytical studies, planning options for improving conditions on the upper seam have been developed to optimize extraction while minimizing the negative effects of seam interactions. These options include prediction of potential upper seam damage, guidelines for minimizing inevitable negative interaction effects, and recommended opening and pillar sizes, shape, and orientations, as well as design and planning procedures.

Jan 1, 1988