Search Documents

A roof rating system has been devel¬oped for upper seam damage prediction during mul¬ti-seam mining based on structural and geologic conditions in the upper seam. Two primary consid¬erations -geologic and spatial - form the basis of the classification system. It includes factors commonly found in geomechanics classification systems as well as factors which are peculiar to multi-seam mining, such as those which define the two adjacent seams and the innerburden. This rating system has been applied to numerous case studies to form empirical relationships for quan-titatively predicting potential upper seam damage based on anticipated subsidence and strain values and vertical movements.

Jan 1, 1988

By Shaning Yu, Yosry A. Attia

The purpose of this work was to investigate the feasibility of using column flotation as a floc separation technique. In this study, the ultrafine coal (minus 25 microns) slurries were cleaned by using the Integration of column flotation with selective flocculation. It was found that using column flotation as a floc separation technique during the "cleaning" stage, achieved much better results than that either using column flotation as a rougher separation technique for coal flocs, or using It directly to recover the ultrafine coal from the slurries without adding selective flocculant. Thus, the ultrafine coal slurries were first separated by selective flocculation process to reject a certain amount of the dispersed ultrafine ash minerals, and to aggregate the ultrafine coal particles as flocs. Thus, the entrainment of ultrafine ash minerals Into the coal floc-froth concentrate during flotation could be considerably reduced. Subsequently, the coal flocs were further "cleaned" by column flotation. The experimental results Indicated that this approach was technically feasible and particularly suitable for a slurry containing a large amount of ultrafine particles. The effect of flotation time, and collector dosage on column flotation of coal flocs were also Investigated and reported In this article.

Jan 1, 1988

By R. H. Parker, B. A. Wills, D. G. Binns

Introduction With the increasing need to mine lower grade ores, high energy-related costs in comminution are of major concern. Very fine grinding is needed to liberate the fine mineral particles in these ores. Not only is this expensive, but it leads to greater losses in slimes. Gravity concentration techniques become unacceptably inefficient for particle treatment below 25 to 50 µm, and even flotation fails in the ultra-fine range. Ore from the South Crofty mine near Redruth, Cornwall, was subjected to thermal pretreatment in the hope that differential thermal expansion of the minerals would lead to intergranular cracking, and thus enhanced liberation. South Crofty ore contains about 1% tin as cassiterite associated with a complex assemblage of quartz, chlorite, tourmaline, and hema¬tite in granite and slate. Recovery of cassiterite can be as low as 70%, as overgrinding occurs during stage reduction of the material to 1 mm (primary grinding) and 180 µm (regrinding). Cassiterite is present in grain sizes ranging from submicroscopic to + 10 mm, the bulk being predominantly in the range of 50 µm to 3 mm. Experimental Flat polished sections of the ore were photographed in reflected light using a Vickers M17 microscope. The sections were then heated in a Carbolite LMF4 muffle furnace. The heating rate and temperature were monitored by a thermocouple immersed in the bed of particles. Previous work by Sherring (1981) on the same material showed that a 55% reduction in grinding resistance occurred when the material was rapidly heated and cooled through the quartz inversion tem¬perature (573°C), where a volumetric expansion of 0.86% occurs. The samples were therefore heated to 650°C at 26°/min, and were then water-quenched to room temperature. The effect of heat treatment on the mineralogy and fracture network was assessed by examining the same area after treatment. Results Most of the sections examined showed that extensive transgranular cracking occurred as a result of heat treatment. Such cracking, although weakening the rock and hence reducing the work index, would in no way enhance the liberation of the cassiterite from the host minerals. Intergranular cracking, which would lead to enhanced liberation, was difficult to discern under reflected light, but there was evidence of such cracking in some of the sections examined. Figures 1 and 2 are examples of typical sections before and after heat treatment. Figures la and lb - show cassiterite in hematite, Fig. lb, in normal incident illumination, illustrating clearly that after heat treatment, transgranular fracture is evident in the cassiterite. If any intergranular cracking has occurred, it is not evident in this photograph. Figures 2a and 2b show cassiterite in quartz before and after treatment. Fracturing in both minerals after treatment can clearly be seen, and there is evidence of intergranular fracturing. However, protruding "arms" of cassiterite are severed by transgranular fracture. Subgrains of quartz have also been isolated by trans¬granular fracture. There is major transgranular cracking across the wider sections of cassiterite. Discussion The effect of rapidly heating South Crofty tin ore to 650°C, followed by water-quenching to room temperature, has been studied by observing the fracture networks in mineral grains. The choice of 650°C as the heating temperature was influenced by the work of Sherring (1981), who found considerable reduction in grinding resistance after thermal pretreatment of the same ore. Scheding et al. (1981), however, have shown, by means of a crude calculation, that heat treatment cannot be justified solely on the basis of reduced grinding costs. The cost of heat treatment far out-weighs that of grinding, resulting in the combined costs for heat treatment being over six times that for grinding unheated material. The most economically attractive aspect of heat treatment is the possibility of enhanced liberation of the valuable mineral due to increased intergranular rather than transgranular fracture. Grinding costs would be greatly reduced by improved liberation at coarser sizes, and the costs of ancillary processes, such as dewatering and tailings disposal, would be reduced. The most significant economic effect, however, would be in improved metallurgical efficiency. Improved liberation would increase concentrate grades, and recoveries would be higher, particularly in the case of ores where high slime losses are produced due to the excessively fine grinding required to produce adequate liberation. Manser (1983) has shown that only a 1% increase in tin recovery, at the same concentrate grade, would be sufficient to offset heat treatment costs on South Crofty ore. Heavy liquid analysis and shaking table separation have been used to evaluate the effect of thermal treatment on processing (Binns, 1984; Scheding, 1981; Sherring, 1981). However, treatment of unheated and heated samples of South Crofty ore, ground to the same product size, by such methods have shown little evidence of improved metallurgical efficiency after thermal pretreatment. The large amount of transgranular fracturing revealed by reflected light studies helps to explain this lack of improvement. Nevertheless, from the evidence of some of the fracture work, it is surprising that no improvements in metallurgical

Jan 1, 1988

By R. R. Klimpel

The process of froth flotation as a means of upgrading the quality of coal by removing ash/pyrite and of separating selected mineral(s) from undesired gangue materials is certainly one of the most common unit engineering operations in use today. Flotation has been successfully practiced at the industrial scale for well over 50 years, and if anything, its use is increasing due to the ever decreasing feed grades of the coals and minerals being processed. Flotation, as a process, has also shown itself to be an extremely flexible process that lends itself well to a wide variety of solid/solid separations. Thus separations can involve very different particle sizes, particle densities, relative weight ratios of materials to be separated, etc., with surprisingly little modification in equipment and operating philosophy required.

Jan 1, 1988

By T. W. West

INTRODUCTION This paper presents an assessment of conventional flotation technology. In addition it presents some ideas which can be used to change the perception of what may be done with conventional flotation equipment to maximize its efficiency. Perspective of Conventional Flotation Technology 1. Flotation in many coal preparation plants is defined as something between a necessary evil and a non-viable concept because: -Too much art is required on a continuous basis to achieve uniformly acceptable results. -It is expensive, the capital cost in dollars per ton of circuit feed for flotation and dewatering is high. -It is a difficult process to use when SO2 reduction governs system design and equipment selection. -It creates a product (fine coal froth) that is difficult to dewater in the presence of BTU/lb as-received pressures. -It is a difficult process to control from a management standpoint, there are no dependable set points to rely on. 2. Many froth cell circuits are 0.5m x 0 (nominal 28 M x 0) feed which is sourced from screen/cyclone underflows. The original intent was to obtain maximum yield at acceptable product quality and moisture using disc filters. (See Figure #1) 3. An alternate to conventional flotation and its perceived to be limits of efficiency, capital costs, etc. is to move towards such developing flotation technologies as column flotation, reverse flotation, and microbubbles. A lot of work is being done to move these concepts thru pilot stages into full scale, commercial plant operation. The majority of the coal producers and coal preparation plant designers view these concepts as being in the development/pilot plant stages. OBJECTIVES Based on the preceeding comments of the perspectives of the coal producers and plant designers, the options are limited. They can make do with what they have available to them in the way of industry standard equipment and practices or they can move forward with developing technology. I feel there is a third option: what can we really do today with what is available to us, without reinventing the wheel? APPROACH 1. When processing coal against ash and SO2 restrictions, the fine clean coal stream can be the best stream on the clean coal conveyor due to the release by size and the ability to create a high BTU/low sulfur (dry basis) product. 2. Targets: -Consistent raw coal size consist in the plant feed . -Do not put pyrites in the froth cells. -Adjust criteria defining good flotation away from yield towards maximum BTU recovery at minimum ash. -Limit the froth cell feed size consist to 0.15 mm x 0 (nominal 100M x 0). -Establish and maintain a correct, consistent percent solids in the froth cell feed. -Select flotation reagents with care. -Introduce reagents in the proper sequence.

Jan 1, 1988

By R. L. Pozzo, I. Iwasaki

A previous investigation showed that corrosion currents estimated from polarization curves for the pyrrhotite-grinding media system under abrasion correlated well with corrosion currents estimated from marked ball wear test data by applying Faraday's law. Freshly abraded metal debris were magnetically attracted to pyrrhotite and lowered the rest potentials of the mineral particles, thereby affecting the corrosive wear. The investigation was extended to explore the interactions between a non- magnetic sulfide mineral, pyrite, and abraded metal debris and their effects on the corrosive wear mechanism. The electrochemical behavior of a three-

Jan 1, 1988

By P. Eng. Daniel Kelly

INTRODUCTION The Astoria property is located in the prolifically mineralized Abitibi greenstone belt and is one of the most advanced projects presently under development by Yorbeau Resources Inc. This property, which hosts the Astoria gold deposit, is located in the southern part of Rouyn township, Abitibi area, Quebec, 4 km south of the city of Rouyn-Noranda (Figure 1). The Astoria deposit has been the subject of underground development for over a half century, beginning with Granada Rouyn Mining Co. in the 1930's and followed by Astoria Rouyn Mines Ltd. in the 1940's. Yorbeau Resources Inc. acquired the property in 1984 and has, since then, conducted numerous exploration programs on this gold deposit. The diluted reserves of the Astoria deposit are estimated at 1,3 million metric tons grading 6,14 grams of gold per metric ton (1.4 million st at 0.18 oz/st). This reserve figure is based on the results of surface and underground exploration carried out from January 1986 to June 1987 and includes ore in the proven, probable and possible categories. This paper is divided into two sections. The first part includes a summary of the geological environment including a description of the gold bearing zones and a short discussion on wall rock alteration. The second part of this paper reviews the underground work and the objective of the ongoing exploration program.

Jan 1, 1988

By John W. Amos, John A. Christophersen

The Deister No. 7, "77" and "88" Coal Washing Tables have been used by the coal industry in the cleaning of finer sizes of coal (-1/2") since washing of coals became necessary. This paper will deal with the in-plant use of the CONCENCO "88" Deister Coal Washing Table, along with a brief description of the Deister Refuse Superscalper. Efficient in-plant operation of the Deister Coal Washing Table can be accomplished by the adjustment of six basic variables. These variables are: 1. Headmotion 2. Feed 3. Riffle Pattern 4. Dressing Water 5. End Elevation Adjustment 6. Side Tilt Adjustment VARIABLE NO. 1 HEADMOTION The reciprocating movement of the "88" Table is developed within the headmotion entirely by rotating eccentric weights. Four parallel shafts each carry pairs of eccentric weights (Figure 1-A). The shafts are geared together with gears of 2 to 1 and 1 to 1 ratios, so that the two shafts in vertical alignment which carry the small eccentric weights operate at twice the speed of the other two shafts. The other two shafts are also in vertical alignment with each other and carry large eccentric weights. As power is supplied to one high-speed shaft, once each revolution the forces produced by the large eccentric weights are reinforced and then opposed by the small eccentric weights in a horizontal plane. The direction of movement of the table decks is reversed much more sharply at the forward end than at the backboard end of the stroke, causing material to move toward the refuse end of the table. Because in the vertical plane all centrifugal forces oppose each other and cancel out, there is no vertical movement and virtually no impact to the support steel. The "88" Coal Washing Table is suspended by wire-rope cables from three overhead steel beams, and operates with a perfectly uniform and exact differential motion curve in every stroke (Figure 1-B). The decks, being attached to the headmotion, are reciprocated in a parallel line from the head- motion to the refuse corner at speeds varying from 260-300 strokes per minute. Both length of stroke and speed are set at the factory for the coal characteristic desired and should not be changed. A 3 HP motor is mounted on the top of the headmotion and uses 3 V-belts to transmit driving power to the headmotion. The headmotion must be kept running on a horizontal plane. Punch marks are provided on the side and end of the main frame for use in leveling the motion (Figure 1-C). In leveling the motion, the work must always be done with two cables. To level the long side of the headmotion both front or both rear cables are raised or lowered to bring motion back to level. To level side to side, both right side cables or left side cables are raised or lowered to bring motion back to level VARlABLE NO. 2 FEED When tabling different size coals, each deck of a "88" DIAGONAL-DECK Coal Washing Table will handle feeds as described in figure 2-A.

Jan 1, 1988

By K. M. Reim

Planning the development of the Quartz Hill molybdenum open pit mine in Southeast Alaska required a number of special considerations. Located in mountainous glaciated terrain, about 3.8 m (150 in.) of annual precipitation (with annual snowfall over 10.2 m (400 :in.) was a primary consideration. Mine planning included muskeg and snow removal, avalanche control, clearing timber, water quality control, dust control, seismicity, mine schedule, work force and reclamation. Quartz Hill is in an environmentally sensitive area which has required extensive environmental baseline data collection, four Environmental Impact statements (EIS) and a large number of permits.

Jan 1, 1988

By J. A. Finch

The use of pneumatic methods for measuring interface level in flotation columns is analysed. It is shown that errors can vary over a wide range (e.g. 40 cm. in one industrial application) depending on bubble size, particle size, bubble loading, liquid hold-up and bulk slurry density. Accurate measurements (+ 5 cm) can be obtained by measuring intensive properties of the froth near the interface. Methods based on the measurement of temperature and conductivity are described and analysed. Control of the interface level using these measurements subject to various disturbances is demonstrated.

Jan 1, 1988

By K. P. Madhusudhanan, R. K. Bhatia, K. S. Narasimhan, R. N. Singh

A typical case study of a coal washery of capacity 500 t/h raw coal input has been presented and discussed with particular reference to the techno-economics for flotation column vis-a-vis the conventional flotation cells, keeping parameters like input capacity and product ash same. The results presented indicate that substitution of flotation cells by columns in a coal washery results in advantages of increased fine coal recovery, better quality of concentrates, lower capital and production costs etc.,. The effect of increasing the specific capacity of the column by design modifications on the cost benefit is also analysed.

Jan 1, 1988

By G. W. Heunisch

The properties of Neutra-Fix® and Neutra-Ment®, two new lime substitutes for treating acid mine drainage (AMD), have been compared with lime and Allcament®, two products presently in use for AMD treatment. The two new products are basically dolomitic byproducts and produce sludges that are more compact than those from lime. Sludge settling rates are faster than lime with iron concentrations after 24 hours that comply with Environmental Protection Agency (EPA) regulations. Material utilization and optimum pH are reported.

Jan 1, 1988

By Risto Lindsberg

A wide concept of flotation equipment and technologies is presented in this paper. The basis for the presentation in Outokumpu's world-wide experience in mineral processing and other related areas, and continuing research and development work done in Finland as well as abroad by Outokumpu's subsidiaries (and customers). It is understood that flotation equipment selection for a certain process stage is becoming more complicated. It is obvious that flotation equipment in grinding circuit needs different design from a multistage cleaning process. In this paper, column flotation is compared with other flotation methods. Thus three areas of flotation are discussed in this paper: 1. Flotation in the grinding circuit, Skim-Air machines 2. Rougher-scavenger flotation, conventional cells vs columns 3. Cleaning flotation, columns

Jan 1, 1988

By Kevin D. Lofftus

This paper presents a dynamic model for column flotation. The model equations are normalized and the dimensionless groups that are directly responsible in determining the column flotation behavior are identified. The resulting model equations are incorporated for computer simulation. Numerical results from computer simulations are analyzed to gather information about design and operation of column flotation devices.

Jan 1, 1988

By N. S. Harding, M. C. Mai, A. G. Fonseca

Many coal characteristics affect combustion performance. Mill wear, boiler efficiency and derate, slagging, fouling, and ash collection and removal are only a few of the impacts of coal quality on boiler performance. The ability to assess fuel characteristic impacts on busbar costs is essential, although difficult to obtain. The relationships between coal characteristics and ignitability, operability, slagging, and fouling were investigated. The examination of combustion data/performance from a laboratory study, a boiler simulation system (pilot combustor), and commercial boilers indicated the benefits of burning improved quality coal. The specific effects of cleaning are discussed. A validation of the necessity of commercial-scale and/or pilot-scale testing is presented.

Jan 1, 1988

By N. S. Tanious

The accuracy of vibrating wire stress meters has been questioned by various users in the mining industry. During an in situ coal pillar study, a laboratory evaluation program was developed to determine whether stress meters could produce reliable measurements in coal. More than $0 stress meters were tested for accuracy, repeatability, effects of setting pressure, and the concept of using a single curve for interpreting the stress-meter data. The testing medium was lucite, a material with a modulus of elasticity very similar to coal. The evaluation demonstrated that the stress meters did provide repeatable measurements, but that accuracy was lacking when the recommended interpretation technique was used. Therefore, a new technique was developed that required all stress meters to be calibrated in the laboratory before use in the field. This new technique reduced the average error to typically less than 10% and, in the worst case, to below 15%.

Jan 1, 1988

By J. R. Aggson

In an effort to minimize cutter roof failures in longwall development entries of a West Virginia coal mine, a three-entry system was developed with the center entry arched into the strata above the coal seam. The purpose of the arched entry was to modify the horizontal stress envelope associated with the three-entry system and improve roof conditions in the adjacent outside entries. Contrary to the predictions of elastic analyses, the presence of the arched entry improved roof conditions by eliminating cutter roof failures in the outside entries. In-situ stress determinations and numerical modeling techniques were employed to quantify the impact of the arch and investigate the mechanism of stress relief associated with the arched entry. Stress determinations and underground observations indicated that the roofs of the outside entries were within the zone of stress relief generated by the arch, and that failure or movement along bedding plane discontinuities played a major role in the formation of the stress relieved zone. The numerical model incorporated horizontal joints to simulate bedding plane discontinuities. The properties of the joints were adjusted until roof stresses predicted by the model were in agreement with measured stress profiles. This process resulted in a calibrated analytical tool that could be used to evaluate alternate mining geometries.

Jan 1, 1988

By S. K. Vidyarthi

Most wastewater clean-up processes suffer from a fundamental lack of specificity in that a Reverse Osmosis process removes all dissolved solids, an Electrodialysis Reversal process removes all ions, wanted or unwanted, etc. Most techniques require the use of a membrane or contact surfaces that are prone to foul-up and are ineffective in situations where solids may be present. A photochemical process for the metallurgical industry on the other hand has the ability to operate specifically on targets that can range from one selected ion to an entire group of homologous species such as all biologically active species. Processes can be designed to change the oxidation states of a target altering the environmental impact. Several processes are currently in operation ranging from Cyanide removal to disposal of radiation wastes. This paper describes applicable photochemical processes with the help of certain key model examples.

Jan 1, 1988

By I. D. Lindley

The Wild Dog vein gold deposit in East New Britain Province, Papua New Guinea, forms part of a recently discovered 26 km zone of auriferous quartz vein mineralisation. The deposit, which was discovered in July 1983, has no silt anomaly, and a panned concentrate anomaly and float train restricted to within 500 m and 800 m respectively, of the discovery outcrop. Discovery of the Wild Dog deposit was a result of the methodical followup of regional panning which, as followup progressed, was replaced in importance by float sampling. Of the sampling methods used during the exploration leading to discovery, panning and float followup provided immediate indications of the presence of mineralisation. This high degree of spontaneity of followup is not provided by geochemical techniques, and has obvious advantages in high cost exploration for precious metal deposits in remote locations.

Jan 1, 1988

By R. Harris, M. Misra

Column flotation technology has a demonstrated potential for recovering clean coal from high-ash waste fines. The effect of different variables such as air flow rate, frother addition, depressant addition, percent solids and particle size on the quality of separation are discussed. Results indicate that air flow rate and depressant addition are the important variables which control the selectivity in the flotation of fine coal in a column cell. Separation efficiency achieved with column cells is significantly better than that with conventional flotation cells. Under appropriate experimental conditions with a deep column, more than 80 percent coal can be recovered in the concentrate containing 10 percent ash from waste fines containing over 60 percent ash.

Jan 1, 1988