Search Documents

By Prisbrey K., N. Choi, A. Burbank

Large tonnages of low grade refractory gold ores are not presently being treated because they resist direct cyanide heap leaching and because they are too low in grade for more expensive oxidizing pre-treatments. If they could be oxidized while remaining in heaps, they could be economically leached with cyanide. The solution is to use bacteria to partially oxidize the encapsulating pyrite mineral which allows cyanide dissolution of the gold in a separate treatment. A variety of refractory ores from different locations was crushed to minus three quarters inch, loaded into columns, and inoculated with T. ferrooxidans. The bacteria attacked the pyrite causing biooxidation, and gold recovery increased 30 to 120 percent after three months curing.

Jan 1, 1990

By D. Butler

Subsurface density changes can be detected by very precise surface gravity measurements. A feasibility study, combined with field experience using modern instruments, will indicate the probability of success. In addition to projected anomaly parameters, surface conditions that effect the survey precision must be evaluated. Examples with excavated zones at 9 m (30 ft) of depth and [+] 22 microgal error are compared to the same model at 30 m (98 ft) of depth. The figures illustrate anomaly detectability. The survey error is a function of surface topography and lateral density variation in the very near surface.

Jan 1, 1990

By Alain Broussaud, Guy Fourniguet, Jacques Franck, Pierre Conil

Steady-state simulation is now in current use to assist mineral processing plant design and optimization. However, the reliability of results generated by simulators has not until now been seriously investigated. A simulator supervision algorithm was designed and programmed to study both the influence of the reliability of experimental data on the accuracy of unit operation model calibration, and the influence of unit operation model accuracy on the results of direct plant simulations. An application to a grinding flotation plant is described and discussed. The approach may open the way to the quantitative analysis of the risks taken in mineral processing projects, which would be similar to the application of geostatistics to mining projects.

Jan 1, 1990

By Robert D. Brown, Charles A. Sorrell

The decade of the 1980's saw "advanced materials" become a key factor among the industrialized nations, with the United States, Japan, and the European Economic Community being the major competitors. All three have identified communications technology, advanced materials, and biotechnology as the keys to future industrial leadership and the closing decade of the 20th Century is expected to be an era of rapid development and restructuring. The progress of EC'92, the effort to develop uniform standards and remove trade barriers in Europe; the determination of Japan to commercialize advanced structural ceramics, alloys, composites, and superconductors; and the emergence of less developed countries as major supplies of commodity materials pose enormous challenges to the position of the United States as an industrial and financial leader. A consensus is developing that the industries that are first to commercialize the large array of new structural materials and electronic, optical, and magnetic materials and devices will be those who determine the structure of national and world economics. Many technical, economic, legal, political, social, and cultural factors are important determinants in the race to commercialize new materials. Millions of words have been written about these factors and their interdependence; yet the sheer complexity of the problems, the rate at which changes are taking place, and the economic risks involved are so great that government policy makers and industrial decision makers find adequate understanding to be very difficult. Of the many factors involved in advanced materials, the Bureau of Mines has the statutory responsibility to provide information on where materials can be found and how they are mined, extracted, purified, combined, and recycled. It is obvious that minerals availability is essential to implementation of any new technology just as there can be no commodity metals industry if the ores are not available. Because "minerals availability" for commercialization of advanced materials and devices is more complex than for commodity materials and a new mix of materials and processes is emerging, the Information and Analysis Directorate of the Bureau of Mines is redirecting resources to provide reliable information for policy and decision making. The Office of Advanced Materials Coordination (OAMC) was established as a staff operation in July 1987 to assist the efforts of the divisions and branches. The key issues and problems were defined and the role of the Bureau was outlined (Sorrell, 1987, 1988). In February 1990, the functions of OAMC were transferred to the new Branch of Advanced Materials, a line organization parallel with the Branches of Ferrous, Nonferrous, and Industrial Minerals, and was given the responsibility for developing new methods to acquire, analyze, and disseminate information about new materials. The purpose of this paper is to provide definitions, a summary of major issues and problems, an overview of minerals and processing availability problems, and a perspective of the ways in which the mining and materials industries can help to ensure domestic availability of raw and processed materials.

Jan 1, 1990

By Y. Numata

2-Mercaptobenzothiazole (MBT) is a heterocyclic-mercaptan and belongs to a group of molecules containing nitrogen and sulfur as electron donor atoms. MBT has been employed as a collector in flotation under names of MBT, Captax, and Flotagen. It is a major constituent of reagents in the 400 series of the American Cyanamid Co. Current applications of the reagent include flotation of copper minerals, tarnished or oxidized lead, copper activated sphalerite, and nickel ores. It has been used successfully in the flotation of pyrite in acid circuits in the range of 4 to 5.

Jan 1, 1990

By G. L. Mowrey

One of the critical parameters of any automated coal mining system is the ability to only cut coal and not the rock / waste surrounding it. To do this the system must be able to detect where the coal-rock/ waste interface is. The U.S. Bureau of Mines is investigating a new approach to vibrational coal interface detection (CID) by utilizing an adaptive signal discrimination (ASD) system to perform feature extraction and classification of complex vibrational signals. Accelerometers, geophones, and piezoelectric films are mounted on mining machines and/or strata and are used to monitor vibrations produced during mining operations. Selected data are digitized and the ASD system is trained on known types of vibrations (e.g., "cutting coal" and "starting to cut roof"). A signal classifier is then generated which can be used to identify unknown waveforms. The ASD system can be retrained if mining conditions change significantly.

Jan 1, 1990

By S. R. Bryan, J. D. Stephens, D. R. Rothbard

The distributions of gold and associated elements in mineral grains from a pyritic gold ore were studied by optical microscopy, and by SEM and SIMS imagery. Products studied were a sulfide flotation concentrate, a calcined sulfide concentrate, a cyanide leached calcine, and a cyanide leached pressure oxidation residue. Individual pyrite grains are compositionally zoned and solid solution gold occurs in some, but not all zones. Most of the gold in calcined products is present as metallic coalesced grains that are smaller than 100 angstroms. Gold lost into cyanide leached residues from the calcines tends to be in “semi-dense” grains that cannot be distinguished from gold-free grains except by SIMS analysis. The gold in cyanide leached pressure oxidation residues occurs as solid solution gold in unoxidized pyrite remnants.

Jan 1, 1990

Application of microprocessors, programmable logic devices, and other computer-oriented hardware and software on-board large surface mining equipment to optimize availability and productivity, stretch machine life, and protect against catastrophic breakdown has been a goal of heavy-equipment manufacturers for several years. Progress in this direction has not been as rapid as many manufacturers anticipated in the mid-1980s, and, on the other side of the coin, mining industry and machine operator acceptance of such products has not always been enthusiastic. However, the trend toward such development seems undeniable. Large surface mining equipment in the future will doubtless carry more, and not fewer, applications of computers and computer-related products. The intensity of development interest and degree of progress in commercializing such on-board computer and computer-related products on surface mining equipment varies considerably among the manufacturers. Summarized here are the on-board computer-oriented products of three heavy-equipment suppliers-P&H Harnishfeger, Marathon LeTourneau, and Haulpak not a comprehensive survey, but, perhaps indicative of the direction such development is taking.

Jan 1, 1990

By F. N. Kissell

The US Bureau of Mines undertook a study of those factors influencing worker escape from an outby coal mine fire. The results of this investigation were two-fold. First, those factors affecting escape from a mine fire were defined, and second, the relationships between these factors were identified. Although the individual components had been studied before, little information was available on their interdependence. Fault tree analysis was used to evaluate the miner escape scenario. After constructing the fault tree, a two-phase analysis of the tree was conducted. During the first phase, the minimal cutsets of the fault tree were identified and ranked. These sets were the smallest sequence of events leading to fatalities during the fire. This ranking revealed that reduced evacuation delays, improved self-rescuer training, and improved stopping construction were important in controlling fatalities during escape from the mine fire. The second phase involved additional analyses of the fault tree. These evaluations were started by first determining occurrence probabilities for each event in the fault tree. Two types of sensitivity analyses were then conducted. The first analysis dealt with changes in event probabilities and their impact on the likelihood of fatalities. The final sensitivity analysis considered dramatic reductions in the probability of fire fatalities. This revealed what event probability values were necessary to reach this level. These results have revealed various remedial actions that could be used to improve the survivability of an outby mine fire.

Jan 1, 1990

By B. C. Lewis

The mining industry has experienced a general trend toward an increasing number of longwall operations, an increasing percentage of underground coal being mined by longwalls, and increasing productivity from the longwalls. Longwall operators have not yet reached a state of mining euphoria. Competitiveness both within the industry and from alternate fuel sources is forcing continued pursuit of higher productivities and lower costs. The following graphics present trends in the industry. Longwall mines, as defined for this presentation, are those reportedly having longwall installations in each of the respective years. Production from both the continuous miner and longwall units is included in the longwall mines. Non-Longwall mines are all other underground mines. Productivity calculations are based on total employee-hours associated with the operation.

Jan 1, 1990

By Ralph P. Hackl

The Congress gold property, located near Goldbridge, B.C., is extremely refractory with most of the gold disseminated in fine- grained arsenopyrite. Metallurgical testwork conducted by Giant Bay Biotech Inc. indicated that biooxidation pretreatment was capable of increasing cyanide gold recovery from the ore to greater than 90%. To determine if the bioleach process could be successfully scaled up, a 225 cubic meter commercial size bioleach reactor was built and tested at the mine site in 1989. At that time the tank was the largest bioleach reactor ever operated. This paper discusses our experiences in operating the tank, summarizes some of the data obtained and describes the problems encountered.

Jan 1, 1990

By Seanley C. Suboleski

This paper examines the likely productivity improvements that have resulted from the introduction of technological advances in underground coal mining during the decade from 1977 to 1987. Included in these advances are the changes in longwall mining; the introduction of larger, more reliable, more repairable continuous miners and shuttle cars; the introduction of remote control and flooded-bed scrubbers; supersections; and other improvements. Procedural improvements are also examined and quantified, the unexplained gains in productivity are attributed to??other factors", among them an increasing maturity of the work force, stabilization of the mining laws, increased labor-management co-operation, and economic urgency.

Jan 1, 1990

By S. M. Bulatovic

The western industrial world has to rely more and more on complex polymetallic sulphide ores as sources for base metals. These ores are composed of fine grained sulphide minerals such as chalcopyrite, galena, sphalerite, pyrite, pyrrhotite and marcasite. The liberation sizes of the individual minerals can range between 30 um and 5 um. Therefore, applying conventional techniques to recover these finely disseminated minerals usually results in unsatisfactory metallurgical performances with high losses of the valuable mineral to the slime , fraction of the tailing. New concepts for treating these polymetallic complex ores are discussed in this paper. Beneficiation techniques utilizing new reagents and a new approach to pulp preparation are described. Some of these techniques were applied to ores from existing concentrators as well as to new ores. The results of these studies are discussed in the following sections.

Jan 1, 1990

By R. R. Sacrison

The Barrick Mercur Gold Mine lies in the Oquirrh Mountains of northern Utah. Limestone, sandstone, shale, and chert are the predominant rock types being mined. Recent expansion has encountered rhyolite. Lithology and structural attitudes control most mechanical behavior. Slope steepening, mine planning, and site selection are presented as means by which geological engineering has contributed to the economics of the operation. Geomechanics investments of approximately $700,000 have resulted in cost savings or additional production worth over $16,000,000.

Jan 1, 1990

By A. C. Burrow, R. P. King

A dynamic model that predicts the variation of carbon content with time in the argon-oxygen decarburization (AOD) process has been developed. The model recognizes three distinct zones in the AOD vessel: the tuyere region in which the blown oxygen reacts very rapidly with the metal components in the molten alloy; a region in which bubbles of inert gas and oxide drop lets rise through the molten alloy; and a zone in which the slag layer can interact with the molten alloy. The process is dynamically controlled by the rate at which dissolved oxygen, produced on the surface of rising oxide droplets, and dissolved carbon diffuse through the molten alloy to react at the surface of the rising bubbles. The rate at which carbon and oxygen react on the bubble surface is assumed to be intrinsically very fast. Predicted decarburization rates compare reasonably well with rates measured in the AOD vessel at Middleburg Steel and Alloys. The model has been developed primarily to allow development of a time-optimal blowing stategy for the AOD vessel.

Jan 1, 1990

By J. Derwin King, Harrison R. Cooper

Applications of nuclear magnetic resonance (NMR) offer possibilities for on-line sensing of the concentrations of several elements in flowing sample streams. In addition to hydrogen, these elements, generally of low-order atomic number, include aluminum, phosphorus, fluorine, sodium, boron, and lithium contained in minerals having commercial importance. Many such elements have been difficult or impossible to successfully measure on-line using the more familiar X-ray fluorescence and neutron activation analysis techniques. The availability of practical on-stream analysis methods is essential to applying advanced controls to processes incorporating these elements. On-stream NMR instrumentation has been demonstrated in the past for several process applications including, as an example, coal flow and analysis; and the technology has recently been extended to the measurement of phosphorous BPL in Florida beneficiation plants. The technique involves simultaneous sensing of proton (hydrogen) and 31P intensities to provide data for continuous calculation of BPL in the phosphate through calibration to volume fractions of water and solids. Initial operating results are described using the PhospholyzerTM on-stream phosphorous analyzer designed for plant application.

Jan 1, 1990

By K. S. Venkataraman

The physical properties of clay-water systems depend on the complicated system of forces between the clay particles themselves, and between the clay particles and the ions in the liquid phase. The kind and distribution of ions in, on, and between the clay particles and the size and the shape of the particles are the basic factors determining the macroscopic behavior of clay-water systems. Understanding the system requires a knowledge of the nature of the clay particles, their size, structure, composition, and surface properties, and of the manner in which they interact with ions [and molecules] in the surrounding liquid [or other medium]. The validity of Professor Brindley's words (Brindley, 1958), written three decades ago in the context of making pottery, whitewares, and electrical porcelains, transcends time, and the basic message is perhaps all the more important in the considerably expanded use of ceramics for structural, thermal, tribological, electronic, and other applications. Silicon carbide, silicon nitride, and sialons have been studied in the last two decades for high- temperature structural and tribological applications, particularly for using in internal combustion engines. Titanates, zirconates and niobates of barium, strontium and lead, have high dielectric constants, and are extensively used in the formulations for making capacitors. Hexagonal ferrites (molecular formula MO.6Fe2O3) are in use for making permanent magnets for fabricating miniature motors, and for assembling loud speakers, particle accelerators etc. Cubic ferrites such as magnesium-zinc ferrite and nickel-zinc ferrite are used as transformer cores, and for other high-frequency applications. In this context, Richerson's recent book (Richerson, 1984) on the general scope of traditional and technical ceramics is a good starting point for an overview of contemporary ceramics technology. Glasses are a whole class of amorphous materials used widely as sintering aids, and for making glass-bonded ceramics and glass-ceramic composites. Composites are yet another burgeoning field where two or more particulate components are used for improving the performance of ceramics. For all these applications, the inorganic starting materials are almost always submicron and near-micron powders. Understanding the powders' physicochemical properties, and their surface chemical interactions with the surrounding liquid/gaseous medium is-necessary for making reliable ceramic parts at competitive prices. Even though ceramics science and engineering has attained its separate identity in universities and the industry, ceramists themselves would concede that ceramics science is a cross-disciplinary field, having incorporated and assimilated within itself many principles from several apparently disjointed disciplines. Principles of material science, graduate-level physics and chemistry, polymer science, surface and colloid chemistry, transport phenomena, particle technology, unit operations commonly used in chemical engineering and mineral processing, and statistics and applied mathematics are integral part of any ceramics curriculum in universities. Added to this is the fact that all bench-scale successes in making ceramic parts are to be scaled-up for larger throughput operations. Understanding and applying process engineering principles of comminution, classification, drying, calcination, etc. then becomes essential. CERAMIC FORMING: Despite the diversity of the materials and processes, conceptually, the steps involved in making ceramic parts have remained the same over several decades: The different components for making the pan (usually one or more powders plus other forming and sintering additives) are proportioned and mixed thoroughly, and the well-mixed formulations are consolidated into desirable shapes known as "green bodies." Usually binders such as wax, clay, organic polymers and surfactants, whether dispersed or dissolved in a suitable liquid are used during mixing the batch for giving strength for the green bodies. In the dried green state, the inorganic powders typically occupy only 55 to 60% of the bulk volume of the body, depending on the particle size distributions of the powders and the forming history, with mostly inter- particle voids accounting for the rest of the void volume. SINTERING: The formed bodies are then fired in high- temperatures kilns/furnaces during which the parts are exposed to a predetermined temperature profile, and "soaked" for a certain duration at the final high temperatures, typically between 1200 K and 1900 K, and then cooled to room temperature. The gaseous atmosphere in the furnace is controlled (oxidizing, reducing, or inert) when necessary. During the initial stages of firing, volatile liquids evaporate, and during the intermediate temperatures between 400 and 600 K, the the organic polymeric additives pyrolize and oxidize into water vapor, CO, C02, and other gases. At still high temperature, the glasses, when present, soften, and simultaneously, the ceramic particles rearrange into a network of grains with definite grain boundaries so as to reduce the total interfacial free

Jan 1, 1990

By Richard R. Klimpel

INTRODUCTION Previous papers by this author have discussed some of the difficulties involved with optimizing the performance of industrial flotation circuits, e.g. Klimpel (1988, 1989). The two major problems seem to be: 1) the inherent "systems" nature of the froth flotation process which leads to a great deal of self-compensation among the various operating options available and 2) the inherent variations in mineralogy, water chemistry, etc. that always seem to be present in industrial operations. In particular, the influence of reagent dosage has been emphasized in the above referenced work including an industrial system interaction denoted as the R/K trade-off, Klimpel (1984, 1987). Using a simple two parameter model for fitting time - recovery data, Klimpel (1980): [ ] where r is cumulative recovery at time t or at the t th cell, R is the long-term equilibrium recovery and K is the first-order rate of mass removal from the cell (time ), the definition of the R/K trade-off with increasing reagent dosage can be given as follows: at low dosages both R and K increase, at intermediate dosages R continues to increase but K starts to level out, and at high dosages, R may flatten out or still continue to increase but K starts to decrease, sometimes rather quickly. An illustration of this effect in a batch laboratory flotation cell is given in Figure 1. The purpose of this paper is to give a detailed plant illustration of this R/K trade-off phenomena with changing collector dosage which shows just how highly interactive the grindinglflotation system in sulfide mineral processing really is. This is one of about 20 plant level case studies that are being presented and evaluated in an upcoming book, Klimpel (1990). The particular study given here was completed in late 1979 on a copper ore of head grade 0.93% Cu. The frother being used was Dowfroth* 250 at a constant dosage of 0.15 g for each ton of solids feed to the rougher bank and the slurry pH was 10.2. The motivation of the study was to better understand the relationship of changes in feed rate (hence in particle size and state of liberation) with variations in collector dosage (potassium amyl xanthate). The major concern was to determine how much extra economic benefit could be gained by better utilizing the existing grinding mills and rougher bank consisting of eight identical cells. The remainder of the flotation circuit was also studied, including regrinding of rougher tails, but did not prove as critical as the rougher bank operation itself. It appeared from an overall economic viewpoint, the battle was being won or lost in the manner in which the rougher bank was being operated. This was not to minimize the roles of the scavenging and cleaning circuits but those portions of this particular circuit could be rather obviously operated to achieve maximum benefit given the specific output of the rougher bank. A special attempt was made to maintain constant ore type throughout the entire test program. Eight specific test conditions were evaluated including three different feed rates (and hence three different size distributions) to flotation. Tables 1 and 2 summarize the eight test conditions and overall recovery results at the end of the rougher bank for each test. A single test consisted of at least three consecutive eight-hour shifts operating at steady-state with composite cell lip samples taken over the final eight-hour shift. "Trademark of The Dow Chemical Company

Jan 1, 1990

By Raymond E. Krauss

The McLaughlin Mine is based on a world class epithermal gold deposit located in the coastal thrust fault of northern California, about 1 12 air km (70 air miles) north of San Francisco. Owned and operated by Homestake Mining Co., the McLaughlin deposit contains about 18 Mt (20 million st) of gold ore at an average grade of 5.2 g/t (0.152 oz per st), or about 93 t (3 million oz). The area was identified as a gold target by Homestake in early 1978. Drilling confirmed it to be a commercial deposit by 1980. The mine was then planned, engineered, built and brought into production by March of 1985. The deposit was historically a part of the Knoxville District. It was mined for cinnabar, which was used to produce mercury for use in recovering gold and silver in the Mother Lode and Comstock districts. At that time, the mine was called the Manhatten and later the One Shot Mine. It was worked for more than 100 years, producing about 76,000 flasks of mercury without any awareness of the presence of economic concentrations of gold. By 1978, the site was largely disturbed and entirely unreclaimed.

Jan 1, 1990

Machine breakdowns and maintenance delays are large contributors to lost production and increased operating costs in the mining industry. The U.S. Bureau of Mines is investigating the applications of expert system technology to diagnostic and predictive maintenance tor mining equipment. This will help increase mining productivity and decrease operating costs, by reducing the frequency of equipment failures and repair times. The Bureau has begun this effort by applying expert system techniques to the diagnosis of hydraulic system problems on a continuous mining machine. This paper discusses the development of the hydraulic diagnostic expert system.

Jan 1, 1990