Search Documents

By M. J. McPherson, P. Mousset-Jones, G. Danko, F. Calizaya, K. You

The friction factor is one of the more difficult parameters to determine in ventilation planning. In practice, this can be estimated from published factors such as those of McElroy. The problem with this approach is that the selection requires some judgement, and the estimated values offer no more than guideline accuracy. This study, examines the effects of four factors on the coefficient of friction for a simulated mine airway. The factors are: airway cross-section, asperity height, flow direction, and cross-cut spacing. The study includes the modeling of a mine airway and the evaluation of the results from 13 experiments on flows of air over rough surfaces. The model, physically represented by a wind tunnel, includes a rough surface section which can be modified to simulate mine airways of various shape and asperity height. Most of the experiments were performed under controlled flow conditions during which the Reynolds number was varied between 50,000 and 300,0000. Based on this study, the friction factor for a mine opening was found to depend not only on the size and shape of the surface asperities but is also affected by the orientation of them in relation to the flow direction.

Jan 1, 1991

By Donald C. Rotherham

The Endako, British Columbia, deposit was initially discovered in 1927 by two local men, Charles H. Foote and Alf Lagdon, who were at that time on a hunting expedition. Four mineral claims were located to cover an area of quartz-molybdenite float that was centered on two small ridges. They subsequently uncovered a 0.5-m (1.6-ft) wide vein on which an inclined shaft was sunk to a depth of 8.3 m (27.2 ft) in 1934. Additionally, a short adit was driven to intersect another vein. Numerous trenches and small pits were also dug. Small test shipments of vein material from this early work were sent to G.S. Eldridge and Co. in Vancouver for metallurgical testing. A concentrate assaying 89.2% MoS, was produced with a recovery reported as 93.3%. The concentrate was essentially free of copper, arsenic, and phosphate. The property was examined by many geologists and engineers during 1934 to 1952, but the only work done was undertaken by the owners in order to maintain their claims in good standing. In 1952, Kennco Explorations (Canada) Ltd. carried out a limited program of bulldozer trenching, sampling, and geological mapping before relin- quishing their option. In 1956, American Standard Mines Ltd. acquired an option on the property, but no assessment work was apparently recorded and the property was allowed to lapse. The key claims were restaked in 1959 by C. Riley and H.T. James of Vancouver. The property was optioned from the new owners by Andrew Robertson in July 1961, and a small amount of trenching was conducted. Robertson, on behalf of his own company, R & P Metals Corp., reoptioned the property in January 1962. The initial results of this work were favorable and justified further exploration. The additional finances required to continue the program resulted in the formation of Endako Mines Ltd. (N.P.L.) on June 21, 1962. Field work by R & P Metals and the first Endako Mines exploration was directed by Bob Couts.

Jan 1, 1991

By Hans-Werner Tonscheidt

Introduction The endeavours to mechanise the shaft sinking operations have led to the development of shaft boring using a V-Mole. The method implies competent ground and a pilot hole of sufficient verticality. This connects the top and the bottom of the shaft and serves for air ventilation and the transport of mullock. The shaft boring machine - nick name V-Mole - with a general pattern similar to a tunnel-borer reames the pilot hole to the designed diameter of the shaft. (Figure 1) The excavating of the rock, the removal of the mullock from the face and the lining of the shaft wall are done simultaneously. If they can be done also continuously this than creates a high potential of productivity. The verticality of the shaft can be garanteed due to the laser beam guided steering system. The diameter of the shaft is variable in steps of 0.5 m between 6.0 and 10 m in accordance with the need. It decides the capacity of the V-Mole to be applied. The depth of the shaft does not depend on the machine. It is practically unlimited as long as a suitable pilot hole is available. Up to 1988 almost 12.656 m of shaft have been drilled on 40 individual projects in Germany and the U.S.A. using a V-Mole. The rocks penetrated were Carboniferous sediments consisting of Sandstones, Shales, Conglomerates and Coal seams. The average uniaxial compressive strength was in the range of 300 - 700 Mpa with a maximum of 1700 Mpa in some singular sandstones.

Jan 1, 1991

By Jr. Wallace

This paper describes the importance of mine ventilation and air conditioning in the operation of a nuclear waste repository. It discusses the impact of ventilation on determining the number and size of shafts and access drifts to and within a repository horizon. The paper also describes the need to maintain separate ventilation systems for waste emplacement and construction operations. The requirement to have filtration capabilities for exhaust air from waste emplacement areas is discussed. Because radioactive high level waste will induce high temperatures in the emplacement drifts, the ability to cool an emplacement drift for re-entry requirements is important. The paper discusses strategies to cool an emplacement drift and the possibility of using continuous airflow to control temperatures in these drifts.

Jan 1, 1991

By F. F. Peng

A unique collector dispersion techniques was developed and used to improve the flotation rate and recovery of coarser and ultrafine coal-rich particles in the froth flotation processes. In this novel collector dispersion method, the collector such as hydrocarbon-oil is gasified and transported by gas phase (air stream) into the pulp. In addition to the excellent mode of collector dispersion, the collector-encapsulated air bubbles are generated in the pulp. This approach alters the surface properties of air bubbles and provides the fast rate of flotation compared to that of direct liquid collector addition froth flotation. Using gasified kerosene as the collector, the effect of altering surface properties of bubbles on the recovery of larger and finer coal-rich particles of -1.7 mm (-12 mesh) and -600 µ m (-30 mesh) raw coal samples were studied. The Redstone seam coal obtained from Northern Central region of West Virginia was used in this work. The effect of particle size on oil-coated bubble flotation rate and recovery were also evaluated. The conventional froth flotation test with a liquid form of kerosene addition was also conducted for comparison purpose.

Jan 1, 1991

By James K. Gowans

The Red Dog Operation is located in northwestern Alaska at Latitude 68°, 100 miles north of the Arctic Circle and 50 miles inland from the Chukchi Sea. The orebody was acquired by the NANA Regional Corporation, (an Alaska Native Corporation established by the Alaska Native Claims Settlement Act of 1971), in 1980 in their land selection. In 1982 Cominco American and the NANA Corporation signed a development agreement and Cominco Alaska Inc., a wholly owned subsidiary of Cominco American, was formed to manage the Red Dog Project. An extensive exploration program in 1980 -1982 outlined a mineral inventory of 85 million tons, at a grade of 5.2% Pb, 17.1 % Zn, and 2.4 oz/ton Ag, which makes the Red Dog the second largest deposit ever discovered. Broken Hill, in Australia, is the only zinc orebody which was originally larger than Red Dog. The design of the facilities is to process 2.1 million tons of ore annually, which will produce 560,000 tons of zinc concentrate, 100,000 tons of lead concentrate and 50,000 tons of bulk lead/zinc concentrate.

Jan 1, 1991

By R. Mohr

Storm water runoff from mine facilities such as haul roads, waste disposal sites and ore bodies have become recognized as the primary facilities associated with non-point source drainage. Depending on the ore body, facility design and geographical setting, nonpoint source drainage can cause pollution impacts to local surface and ground water resources. Non-point source impacts from surface mine drainage have become an important regulatory issue for the mining industry. Implementing non-point source drainage control plans that prevent impacts to water resources can be accomplished cost-effectively with moderate labor requirements. Design considerations for plan development must incorporate parameters including contributing drainage area size, slope, flow velocity, vegetation characteristics and soil scour velocities. The success of non-point source drainage and erosion stabilization planning is based on implementing control measures that dissect drainage patterns, reduce flow velocities and disperse runoff towards sediment control sites. Interim and long-range drainage control measures should begin during exploration activities. Regulatory legislation addressing non-point source pollution sources was enacted as amendments to the Clean Water Act (CWA) in February 1987. The legislation required states to initiate non-point source pollution control programs.

Jan 1, 1991

By Leonard G. Austin

INTRODUCTION Run-of-mine (ROM) coal generally falls into two major groups: that from underground mining (continuous mining machines) and that from strip mining. Continuous miners produce a finer product and strip mining a coarser product that is crushed to produce the desired size. Further size reduction depends on the proposed use or uses for the coal. For example, for pulverized coal power plants as a rough general rule, the coal is ground or pulverized to 80% less than 200 mesh (0.075 mm) before it is blown into the boiler furnace as a coal-air suspension. For solvent-refined coal processes, the desired size is about <30 mesh (< 0.60 mm); in fluidized bed uses, the coal is typically < 8, in. (< 1.6 mm); for Lurgi pressure gasifiers, the desired size is 1 to 2% in. (25 to 63 mm). Coal preparation plants typically work with a coarse size fraction of 6X 1/14 in. (150X32 mm). The past decades has shown a steady increase in the tonnage of coal cleaned, 1 but it seems probable that the next decades will produce much wider applica- tion of deep coal cleaning before use and that the stages of crushing and pulverization from ROM coal to end use will be integrated with coal cleaning processes. Since different cleaning processes work better with different ranges of coal size and the degree of cleaning possible is intimately connected with the size of coal, a systems design engineer will need as much information as possible concerning the size distributions produced by different types of machines and how these can be modified by different ways of operating the machines. In general, the following questions will be of concern: 1.What type of crusher or grinder is best, or most satisfactory, for reducing a given feed size and type of coal to a desired product size? Frequently, the desired product is smaller than some nominal size, but with as few fines as possible, or the fraction in some size range has to be as high as possible. 2. How big does the machine have to be for a given throughput rate? 3. How much electrical energy (or its equivalent) is required per ton of product? 4. How does the size distribution vary with change in throughput rate, and is a control scheme necessary or desirable? 5. Can the size distribution be readily varied if desired? 6. What is the optimum way to operate a machine in a given system? This section will emphasize certain general principles which guide us in answering these questions. PARTICLE SIZING Since particle size and size distribution are the raw information with which we work, it is worthwhile to review the terminology used. In this regard, see

Jan 1, 1991

By Robert A. Haney, David J. Atchison, Kenneth G. Fields

Mining systems with greater than a 20-foot face advance (deep cut) have become popular due to their increased productivity and safety. The face dust collection system used in many of the mines employing the deep cut systems, incorporates a machine mounted dust collector with either a blowing or exhausting line brattice and a remote control operated continuous miner. In order to characterize and quantify the parameters used to control dust with these systems, the Dust Division conducted studies on four mining sections using continuous miners with deep cut mining systems. On each section, the dust control system incorporated line brattice with a machine mounted dust collector. The remote control made it possible for the continuous mining machine to advance further while permitting the operator to remain under supported roof and away from dust generated during mining. The purpose of these studies was to evaluate the effectiveness of deep cut mining systems using dust collectors to control respirable dust exposure. This paper summarizes the results of the studies conducted. At each mine face workers were sampled to determine their full-shift dust exposure. Additionally, fixed point dust samples were collected at various locations to determine relative concentrations of dust generated from mining. Air quantities were measured at each working place to determine the amount of air delivered to the face area. Evaluations were made by comparing worker exposures to respirable dust samples taken at appropriate locations upstream and downstream of the coal faced being mined. An estimate of the amount of the respirable dust being generated at the face during mining and the amount of respirable dust being removed by the dust collectors was made by balancing the air quantities and the dust concentrations immediately upstream and downstream of the coal face. Results of the studies showed that the dust control systems, were effective for controlling workers exposure to respirable dust. Dust collector efficiencies were determined to be approximately 85 percent. While the dust collectors were effective in removing respirable dust, the success of the systems with line brattice greater than twenty feet from the face, was dependent on the use of the remote control which permitted the continuous miner operator to remain out of the high concentration dust cloud in the working face. Dilution from intake air, combined with the dust collector efficiency, maintained exposure of other section workers below applicable standards.

Jan 1, 1991

By Winthrop F. Watts, Robert W. Waytulonis

During the 1980&apos;s. the Mine Safety and Health Administration (MSHA) proposed new regulations for the use of diesel equipment in underground coal mines, and the National Institute for Occupational Safety and Health (NIOSH) recommended that whole diesel exhaust be regarded as "a potential occupational carcinogen", and that reductions in exposure to exhaust pollutants would reduce excess risk. During the same time, the Bureau of Mines tested new emission control technology to minimize diesel emissions. The objectives of this paper are to discuss the major issues regarding diesel exhaust emissions. especially diesel particulate matter (DPM) , and to highlight emission controls that will be available. DPM is a potential health threat because it is respirable in size and is composed of nonvolatile carbon with adsorbed or condensed compounds. These compounds include potentially mutagenic or carcinogenic hydrocarbons such as polynuclear aromatic hydrocarbons and sulfates. DPM contributes to the degradation of air quality in mines with typical mean concentrations ranging from 0.2 to 1.0 mg/m3. In addition to adequate ventilation, control of DPM can be achieved by implemention of improved work practices, regularly scheduled engine maintenance, and emission controls.

Jan 1, 1991

By C. R. Rinschler, G. R. S. Smith

A high-strength, industrial-grade membrane filter- cloth capable of high flow rates and sub-micrometric particle retention has been developed. A filtration system using this filter- combined with special filtration techniques and using tubular-filters makes possible the filtration of many difficult-to-jilter slurries. Small, discrete, slowly-settling particles are formed into filter cakes that when pulsed of the membrane filter cloth do not redisperse but settle rapidly to form a dense filter under- flow. A positive separation of solids from liquids is obtained.

Jan 1, 1991

By John R. Marks

In April 1990, the Homestake Gold Mine embarked on a five year, $US 23 million underground drifting and drilling program to explore promising ore targets north of the current mine. This paper describes the ventilation and air-conditioning system that was installed for the 4m x 4m x 5.2 km (ultimately) drift, which is being driven at about 8m per day in 48OC (118.5 F) crystalline rock. Design parameters are described first. Differences in South African, Canadian and U.S. drift ventilation and civil tunneling techniques proved interesting. Details are then given on equipment selection, installation and performance. Costs are included. Special note is made of safety considerations for a long, dead-end drift.

Jan 1, 1991

By W. J. Stone

In response to concerns over the impact of mining on the hydrologic balance at the Navajo Mine in northwestern New Mexico, a recharge study was conducted using a chloride mass- balance approach. Impact of mining on annual recharge volume was assessed by comparing pre- and post-mining recharge values. The mean regional recharge rate for reclaimed ground (weighted by acreage) is 1.02 mm/a (0.04 in. per year) or twice that for undisturbed ground, 05 mm/a (0.02 in. per year). Comparison of regional recharge volumes for identical areas shows mining increases recharge 92%. The increase is only 80% if no closed depressions are constructed during reclamation. However, the increased rates are so low that there should be no detrimental impact on regional water resources. The chloride method proved useful at Navajo Mine and should succeed at others surface coal mines as well.

Jan 1, 1991

By Sarah Vest, Richard Sherman, Leo Martin

In 1988 a major exploration program was undertaken to determine the characteristics of the rock and soil for a 7.6 m diameter sea outfall tunnel beneath Boston Harbor out into Massachusetts Bay. The diffuser discharge location had been mandated by the EPA to a 10 sq. km area of seafloor connected to the proposed Deer Island Treatment Facility by a 14.5 km tunnel corridor. Geophysical surveys, deep rock borings, and laboratory testing, provided the information for the conceptual design. The program identified the range in material types and parameters to prove feasibility of a TBM driven tunnel and to locate the optimum alignment and depth.

Jan 1, 1991

By R. F. Harig

Designing an underground nuclear waste repository is a complex process. Although many decisions are involved before the design is complete, the first three--what the target horizon is, what the underground boundary is, and where the entry point will be located--are important because they establish the basis for the entire repository design. Even more important than these decisions, however, is the data on which the decisions are based. Because the current data are limited, an aggressive data gathering program is needed during the next design phase to augment information about the intricate interplay among all facets of the repository design and the geologic medium in which the proposed repository is to be developed. Although unique to modern engineering enterprises, the challenges involved in designing a repository in the unsaturated zone are within current technology and engineering practices.

Jan 1, 1991

By Ora H. Rostad

Veins containing silver and gold values, with some associated values in copper, lead, and zinc, were discovered in 1890 by Will Kirwin in what was later designated the Kirwin mining district situated on the North Fork of the Wood River, about 56 km (35 miles) west of Meeteetse. (See Fig. I.) After considerable prospecting activity, including the driving of several short adits on veins, most of theclaims in the district were consolidated into two ownerships. One was held by the Galena Ridge Mining Co. which was organized on Nov. 18, 1902. The other was held by the Shoshone Mountain Mining Co. which was organized on Mar. 23, 1903. During the period from 1903 to 1907 inclusive, the two companies continued exploration on veins in their respective areas. The major exploration-development activity for the Galena Ridge Mining Co. was the driving of the Galena Ridge crosscut adit for 709 m (2327 ft), to cut veins at depth which had been explored by short adits high on Galena Ridge. Shoshone Mountain Mining Co. concentrated their work on the Bryan and Pickwick veins. Neither of the companies found ore that was rich enough to sustain profitable operations in that remote locality. Most of the major exploration and development activities were stopped in late 1907. A major snowslide in February 1907 killed three people and destroyed several buildings and may have contributed to discouragement in the area. From 1908 to the early 1920s, only minor exploration work was done. Galena Ridge Mining Co. was dissolved Aug. 5, 1922, and Shoshone Mountain Mining Co. was dissolved on Mar. 23, 1923.

Jan 1, 1991

By E. D. Attanasi

Exploration for non-fuel minerals has declined since 1988 as recessionary pressures have slowed growth in the industrialized economies. By most accounts, however, 1990 expenditures were still significantly greater than the low levels experienced in the mid-1980s. The Persian Gulf crisis introduced instability in energy prices and greater uncertainty into an already cloudy economic picture. As 1990 unfolded, the US savings and loan problems spread to the commercial banking system, leading to the failure of several major US commercial banks. The Japanese stock market also suffered significant losses as Japan&apos;s Central Bank raised interest rates. The Soviet Union experienced shortages of food and other basic items. Its government faces resistance to changes leading to a market economy. Individual Soviet republics also are seeking more control of their own destiny. The cost of German reunification, in terms of the capital required to bring the east&apos;s infrastructure and industrial base to western standards, also appears to have been underestimated.

Jan 1, 1991

By A. Kevin Beaton, Robert W. Laakso

The desire for dry passageways promotes the NATM as it provides a final support system most suitable for the installation of a waterproofing membrane. Waterproofing during construction is a cost effective way to enhance safety and function as well as increasing the life of an underground structure. The NATM approach utilizes the surrounding mass as an integral element of the "ringlike" support system. At the Pennsylvania Turnpike Commission Lehigh Tunnel No. 2 various rock classifications were determined to require support measures ranging from 2 to 12 inches of shotcrete along with spiling, wire mesh, deformed bar, lattice girders and rock bolts as needed. Field instrumentation and monitoring programmes are a key factor for the success of the NATM. When the support "shell" stabilizes smoothing shotcrete, waterproofing and a final liner can be placed.

Jan 1, 1991

By R. L. Brown

The Buchans mining district is located roughly at the center of the island of Newfoundland and contains some 18 separate mineral deposits. The first of these deposits was discovered in 1905, the latest discovery having been made in 1979. To the present (1983), some 16 Mt (17.7 million st) grading 1.33% Cu, 7.5% Pb, 14.5% Zn, 115 g/ t (3.7 oz per ton) Ag, and 1.4 g/t (0.04 oz per ton) Au have been mined. Mining operations are now largely terminated, but a few hundred thousand tons of economically marginal reserves may be mined in a salvage operation. The Geological Association of Canada Special Paper No. 22, "The Buchans Orebodies, 50 years of Mining and Exploration," contains papers which describe the history, geology, and the application of evolving geological concepts in exploration. Papers by Neary, Swanson, and Thurlow and Swanson in that volume are topical to the present discussion. Successful exploration techniques at Buchans included physical prospecting, utilization of the state-of-the-art geophysical techniques, saturation diamond drilling which was made possible by the high gross value of the existing ore, and, since 1955, diamond drilling directed by fairly well understood geological parameters. The record of discovery started in 1905 when the Buchans River deposit was found by Matty Mitchell, a prospector employed by the Anglo- Newfoundland Development Co., a British company which owned mineral rights over a very large area in the Red Indian Lake-Exploits River drainage system.

Jan 1, 1991

By R. H. King

The US coal industry has been using continuous room-and-pillar mining (CRPM) machines for more than 30 years for longwall development. This equipment has also been used for production mining in areas that are not appropriate for longwall mining. From 1977 to 1987, the portion of annual US production mined by continuous miner (CM) sections grew slightly from 65% to 70%. Over this time, mine operators and manufacturers have made some advances to attain the full production potential of this method. This is evidenced by the fact that average tons per eight hour shift for continuous miners in the US grew from 180 t (200 st) in 1977 to 431 t (475 st) in 1987. The authors (1990) reported that the increase in productivity was due to several factors: • a drop in prices; • a more mature workforce; • union stability and incentive programs; •procedural improvements; and •technological advances. The authors estimated that about one-third of the increased production came from the first three and other unaccounted for factors and one-third each for the last two. Even though improvements were considerable, continuous miner capacity is much higher than 431 t/shift (475 st per shift). For example, the machinery is capable of mining more than 9 t (10 st) per machine for the 6.5 available hours per shift or 3.5 kt (3900 st). However, this has never been attained on development. The averages of most mines are less than 900 t/shift

Jan 1, 1991