Search Documents

By Lyman H. Hart

Michiquillay is a major copper deposit situated about 70 km (44 miles) northeast of Cajamarca in northern Peru (Fig. 1). It occurs largely in quartz monzonite in a shatter zone produced by the intersection of northwest- and northeast-trending fault systems. The geology is described by Hollister and Sirvas (1974). The ore deposit was drilled in 1963-1964 by Asarco, with results indicating a resource of 575 Mt (634 million st) averaging 0.72% Cu-0.03% Mo. A decision to bring the project to production has been deferred because world capacity to produce copper has been more than adequate to serve world requirements since 1964. The chain of events leading to the discovery of Michiquillay was set in motion by a decision by the management responsible for the Chilete mine to undertake an investigation of the surrounding area for a possible supplementary source of mill feed to bolster its decreasing lead-zinc reserves. Chilete, located 100 km (62 miles) inland from Pacasmayo, is the most northerly, important mining project in Peru, and little was known of the mineral potential north and east of that point. Relatively unimpressive reports of Colonial silver mining had attracted little investigation, and little was known of the regional geology. One study by Benavides (1956) had been made of the Cretaceous in the region of Cajamarca.

Jan 1, 1991

By Y. C. Kim

This paper describes the implementational aspects of a blast hole kriging system that has been developedfor the purpose of daily ore/waste control in an open pit mine. The primary goal of blast hole kriging is to improve the ore/waste delineation procedure. A complete computer program package called Blast Hole Kriging (BHK) System was developed for IBMIPC AT or XT computers, using the Fortran language and supplemented by a few assembly language routines for the bit- map manipulation. This paper emphasizes the practical implementation requirements of the system and discusses system design considerations.

Jan 1, 1991

By Yan. T. Y.

Uranium precipitation from an eluate using hydrogen peroxide has been studied in a laboratory continuous unit. The important process parameters were the dosage of H2O2, reaction pH and chloride ion concentration. In the process, the alkaline eluate is acidified to a pH of 2, then H2O2 at 110%-130% of the stoichiometric requirement is added, and finally NaOH is added to maintain a pH of 4 for one hour to complete the precipitation and settling. The chloride content in the system is controlled to 50g/L or below by rejecting part of the decant solution. The process has been successfully employed in commercial operations. The uranium recovery is complete, while the precipitate settles rapidly and can be processed to high purity yellow cake without filtration.

Jan 1, 1991

By Vincent Castronova, Jane Y. C. Ma, Joseph K. H. Ma, Chang-geng Mo, Carl J. Malanga

A group of bisbenzylisoquinoline (BBIQ) alkaloids has been shown to exhibit various degrees of effectiveness in preventing silicainduced fibrosis in animal models (1, 2). The capability of these drugs to interact with phosphatidycholine vesicles and rat alveolar macrophages was studied using fluorometric and equilibrium dialysis methods. The lipid binding affinity of these alkaloids was found to depend upon several structural factors including hydrophobic substitutions, the chiral configurations, and the double oxygen bridge-restricted conformation of the benzylisoquinoline moieties. Tetrandrine, which is highly effective in preventing fibrosis, showed strong binding to both lipid vesicles and alveolar macrophages. In contrast, curine and tubocurine, which have little or no effect on silicosis, exhibited only weak binding to lipid vesicles and almost no binding to cells. The moderate binding affinity of fangchinoline to vesicles and cells corresponded to a moderate effectiveness of the compound as an antifibrogenic agent. Methoxyadiantifoline, an alkaloid of unknown antifibrogenic potential, also exhibited high binding affinities for lipid and cells. In summary, this study indicates that alveolar macrophages exhibit large binding capacities for certain members of the BBIQ alkaloids. A positive correlation was observed between binding affinity to alveolar macrophages and the reported antifibrotic potency of these compounds, suggesting that the ability of these drugs to interact with alveolar macrophages may be a key step in inhibition of the progression of silica-induced pulmonary disease.

Jan 1, 1991

By J. D. Morgan

In the first half of the year, lessening of cold war tensions was welcome. But Iraq's invasion of Kuwait in the second half led to the Persian Gulf War in January and February 1991. This caused an oil shock that dampened the economy. So the US gross national product rose only 0.9% to $5,463 billion (US billion = 109). The buildup of military forces in the Persian Gulf area focused greater attention not only on petroleum but also on other strategic materials. The Department of Defense continued to review stockpile goals and to upgrade several mineral materials. In addition, the Bureau of Mines continued to maintain the standby Emergency Minerals Administration. The Defense Production Act, which authorizes priorities, alloca¬tions and supply expansion, lapsed on Oct. 20. So the Selective Service Act of 1967 became the authority for assuring that orders of the armed forces and defense atomic-energy programs were given priority treatment. Consumer demand strongly affects mining worldwide. US citizens carry significant debt, and large stocks of housing and consumer goods are already in place. Some 250 million persons have 188 million licensed motor vehicles and 100 million dwelling units. Consequently, new car production fell 11 %, to 6.1 million units. Truck and bus production fell 8%, to 3.7 million units and new private housing starts fell 13% to 1.2 million units.

Jan 1, 1991

By H. Demirel

This paper deals with concentration of hematitic-limonitic iron ores. The ore sample obtained from Karakuz (Turkey) contain:. about 40-46 I Fe. First, a low intensity magnetic separation process was employed to separate the strongly magnetic particles cf "-10+2 mm" and "-2+0.075 mm" size fractions and magnetic concentrates with 59.1 % Fe aid % 58.0 Fe were obtained respectively. The non-magnetics of both fractions were then fed to a nigh intensity permanent magnetic separator. The Fe contents of "-10+2 nun" and "2+0.075 mm" size fractions were increased from 28.2 to 51.13 and from 35.4 7. to 43.25 respectively after single pass. Easing on these results, it was concluded that the high intensity permanent magnetic separator could he used as a pre-concentrator f.7.1- hematitic-limonitic Karakuz iron ore.

Jan 1, 1991

By J. Partyka

Adequate ventilation is a main concern if Lockerby Mine near Sudbury is to be expended. This study investigate a two-fold problem: (1) the new pressure and volume requirements of the main fans due to the theoretical. deepening of the mine, and (2) the effect of the natural ventilation pressure on the main fans. Field data was analyzed with the aid of a newly developed network simulation program, VNETPC Version 3. 0. The density change throughout the mine is accounted for by performing all computations at reference density. Results of the investigation indicate that the existing fan system must be supported by three to five additional underground fans as well, the density effect is significant. If neglected, it will greatly alter the simulation results

Jan 1, 1991

By W. M. Snoddy

The Montana Tunnels diatreme is a low-grade polymetallic ore body containing economically mineable quantities of gold, silver, lead, and zinc. Widely varying gold grades combined with the general erratic nature of the mineralization create a complex sampling, assaying, and ore control problem. In order to maximize productivity and profitability, a variety of procedures have been used. These include differing sample size, frequency and method. In addition, assay techniques have been adjusted and refined to fit specific requirements, the result of which is an accurate, functional sampling and ore control system.

Jan 1, 1991

In 1990, US mine production of barite increased 54.1 %. Barite consumption, sold or used by grinding plants, increased by 27.6%. Imports were about the same as 1989. World mine production in¬creased 12.3%, according to the US Bureau of Mines. The value of domestically produced barite, fob mine, decreased 12.7%, according to the Bureau. The declared value, cif US port, of all imported crude barite during the year 1990 increased from $40.27/t ($36.54 per st) in 1989 to $40.61/t ($36.84 per st). Nevada continued to be the leading producer of barite with 82% of the total, followed by Georgia and Missouri. It is estimated that 750/c, of the domestically mined barite was used as a weighting agent in drilling fluids. The remaining 25% was used in barium chemicals, glass or as a filler. Most of the production from Missouri, Georgia and Tennessee was used in the non-oilfield sector. Of the total barite used by grinding plants and chemical manufacturers, it is estimated that 90% was used in drilling fluids and 10% in the non-oilfield sector. This includes barium chemicals and fillers in paper, plastics, and glass. Tonnage consumed in the drilling fluids market increased due to the higher average rig count during 1990. The average number of rotary rigs operating, (1010), was 16.2% more than the 1989 average of 869 in the US.

Jan 1, 1991

By Ping Xia, Yaoxin Lu

With productivty increment. it becomes very important to monitor the underground production environment. This paper presents a multi-level computer monitoring and managing system, which was specially developed for the mine. In this system, TF-200, Industrial Standard Buses (STD) and 32 bytes Super micro-computer were integrated into one body as hardware; Data Base was designed by means of software engineering method in the software development; on maitenance of the system, the parameters are managed concentratedly and data are classified to process; therefore, the ystem gets to the advanced level in China. The system is composed of four sub-stations: Signal Transmission. Data Collection, Data Processing and Image Display Sub-system. Signal Transmission Sub-system(STSS) A frequency-division transmission method is used. Data Collect ion Sub-system (DCSS) Industrial Standard Buses (STD) is used. It can change data from STSS into suitable form for DCSS, Calculate average value every minute, decide alarm and transmit data to DPSS. Data Processing Sub-system (DPSS) The host is a S/120. With UNIX Operation System. the data from DCSS can be classified. stored, displayed. printed, by means of real-time and time-division processing. Additionally the functions of the historic data search and data analysis are provide. Image Display Sub-system (IDSS) The real-time and historic data was displayed for curves and diageams on screens. This system has been in operation.

Jan 1, 1991

By Joseph T. Matoney, Okley B. Bucklen, Claude A. Goode, Philip G. Meikle

INRTODUCTION Annual coal production rose to over 1.03 billion st (931 Mt) in 1990. At the same time the number of mines producing this increased tonnage has decreased over 60% in a 30-year period, from 9230 mines in 1960.1 The great increase in production made possible through continued mechanization requires greatly improved loading facilities just to get coal away from the mine. Also the trend to combine production from more than one mine and cleaning it in a single preparation plant continues. A recent census of US coal preparation plants indicated that 310 plants were in operation.2 In addition to increased loading capacity, storage and blending facilities are more necessary both at the producer and user end. In this climate of rapidly changing technology, any written account is faced with the possibility of obsolescence before its appearance. Thus, this chapter seeks to define the common and current practice in coal loading and storage facilities with the full knowledge that this practice is an ever-moving target. FUNDAMENTALS OF COAL STORAGE Storage of coal is becoming an increasingly important part of coal handling systems at mines, particularly since the advent of the unit-train concept in transportation. In order to take advantage of reduced transportation rates on trainload shipments of coal offered by unit-train movement, operators have found that storage is an economic necessity. In unit-train practice, large predetermined quantities must be loaded in relatively short periods of time, as opposed to conventional practice where coal is loaded at a speed dependent on the production capacity of the mine and/or the cleaning capacity of the preparation plant. Clean coal storage is generally practiced in order to accomplish one, or a combination, of the following objectives: 1. To load out promptly and economically. 2. To facilitate blending in order to even out chemical and physical inconsistencies and to prepare desired products or to attain maximum product uniformity. 3. To store certain sizes whose prices and market demand fluctuate with seasons and to permit shipping in good weather. Coal storage, then, is necessary and desirable, both from production and utilization standpoints. There are, however, several undesirable aspects attendant to the storage of coal, the most important of which are oxidation and spontaneous combustion, changes in properties which may affect utilization of the coal, degradation of coal due to rehandling, and the added cost of handling and storage facilities.

Jan 1, 1991

Those who have had an occasion to apply geostatistics to the estimation of ore reserves are familiar with the conventional approaches of estimating average grade of quality values for arrays of regular grid squares or blocks. Further, the technology to perform geostatistical analysis and prediction for irregular two-dimensional areas has been available in a practical, readily useable form for some time. However, the generalization of this technology into three dimensions has been hampered by lack of a suitable geometrical characterization for realistic, three dimensional shapes and volumes. The extension of these estimation techniques into three dimensions has now been made possible by a successful integration of the volume modelling capabilities of 3D Component Modelling with proven 3D Geostatistical Techniques. The result is a powerful new technique for mineral ore reserves estimation in a practical, useable form. The technique allows direct geostatistical estimation of grade and quality values for precisely defined, irregular, realistic, geological, and mining shapes or volumes. This paper describes the two technologies, their integration and their application in practice to the estimation of mineral ore reserves. The paper closes with a discussion of the benefits provided by the new approach, in terms of accuracy, efficiency and practicality.

Jan 1, 1991

By Lee W. Abramson, Glenn M. Boyce

A dowel testing program was conducted as part of the Interstate Route H-3 Trans-Koolau exploratory tunnel project on the island of Oahu, Hawaii. The testing evaluated the performance of dowels to be used as initial ground support for two 12- by 15-meter (40- by 50-foot) tunnels within weathered basalt. The program tested four dowel types of three different lengths. Both grouted and friction dowels were tested. The program determined which dowels were more effective in carrying load and noted any special procedures that would be required during construction. This paper presents the test results and discusses how these results were used in the design.

Jan 1, 1991

By Donald W. Peters

The 191 million acres of public lands that are managed as National Forest System Lands contain extensive geologic habitat for over 40 industrial minerals. The Forest Service actively encourages exploration for and development of industrial mineral deposits within the National Forests. However, due to competing interests, the Forest Service may not always be able to accommodate industry needs. In order to successfully compete with ever-increasing demands for all resources in the 1990's, industry needs to become more active in public involvement and education and in communicating its contributions and needs to public land managers.

Jan 1, 1991

By A. K. Basu

Rapid industrial growth in India has caused the country to realize the strategic importance of its zinc and lead deposits. Private companies, nationalized in 1965, are now a corporate public sector organization that is making great strides in developing the nation's lead-zinc mining capability. The main mining area is centered around Zawar at Rajasthan. It consists a group of mines - Mochia, Balaria, Zawarmala and Baroi. Mining activities have also been extended by opening the mines at Rajpura-Dariba at Rajasthan, Sargipallie at Orissa and Agnigundala at Andhra Pradesh. A huge deposit has been explored at Agucha in the Bhilwara district but full-scale production has not yet begun. Annual consumption of zinc and lead in India has risen steadily from 25 and 7.9 kt (27,500 and 8700 st), respectively, in 1973-1974 to 162.8 and 80 kt (179,450 and 88,000 st), respectively, in 1989-1990. Mine production has also risen consistently to cope with the increased metal demand. The mining company hopes to increase production at existing mines and upgrade the beneficiation and smelting facilities. Moreover, mining operations may be expanded by opening up new units that are now awaiting governmental clearances. Technology status Mining technology has undergone a rapid, large-scale transformation, with an accelerated pace of new, larger capacity mine development. Notable advances include the introduction of mechanized ore extraction methods and

Jan 1, 1991

By Olice C. Carter, B. J. Scheiner

The Bureau of Mines investigated the removal of two toxic/heavy metals (cadmium (Cd) and lead (Pb)) from brass foundry wastewater. Polymers, copolymers, guars, and gums were used in conjunction with calcium hydroxide (Ca(OH)2) and magnesium oxide (MgO) to remove the metals from solution. Several polymers were successful in removing Cd and Pb from the wastewater. The concentrations of Cd and Pb were lowered from 19 to 0.01 ppm and from 20 to less than 0.01 ppm, respectively. The methods investigated could easily be adapted to many existing wastewater treatment facilities and/or be used independently.

Jan 1, 1991

By S. R. Wardwell, M. J. Robison

INTRODUCTION The first phase of the Los Angeles Metro Rail Project consists of 7.1 km of subway and stations running through downtown Los Angeles from Union Station to MacArthur Park. Contract A146, Tunnels from 5th/HILL Station to 7th/Flower Station, involves tunnel construction through the heart of downtown Los Angeles. The alignment of the tunnels passes beneath twelve buildings, ranging from a 3-story below grade parking structure to numerous 12 to 14 story buildings. The soil along the alignment is alluvium, consisting of silts and clays, clean sands and gravels located above the ground water table. Because of unstable ground conditions, which led to excessive ground losses in several instances, and because of the potential for excessive building settlements, it became necessary to design and perform a program of chemical grouting. The chemical grouting program was designed such that tunneling could proceed on a one shift per day basis, with chemical grounting being performed on the remaining two shifts. Each day 21,000 to 31,000 liters of sodium silicate grout were injected through sleeveport grout pipes installed 18 m deep through the tunnel face. Tunnel advance rates of 12 m per day, 60 m per week, under full chemical grout cover were achieved. The chemical grouting program virtually eliminated both ground loss and settlement and permitted successful excavation of the tunnels. The purpose of this paper is to describe the chemical grouting program used to control ground losses and settlement on Los Angeles Metro Rail Contract A146. The paper begins with a description of

Jan 1, 1991

By Gary D. Babbitt

Facing an orchestrated assault from the anti-mining lobby and its congressional allies, the Mining Law of 1872 may soon be either dramatically changed or even repealed. In 1989, Sen. Dale Bumpers (D-AK) introduced Senate Bill 1126 entitled the "Mining Law of 1989." It has been through several hearings and is still in the Senate Committee on Energy and Natural Resources, where Sen. Bumpers is the number two ranking Democrat. In the House, Rep. Nick J. Rahall (D-WV) introduced the "Mineral Development and Exploration Act of 1990," HR 3866. This bill is in the House Committee on Interior and Insu¬lar Affairs. (The numbers on these bills, and perhaps some of their language, will be changed when they are reintroduced in early 1991. However, their substance is expected to remain substantially unchanged. Bill numbers here refer to legislation as it was numbered in the 1990 Congress.) In the eyes of its supporters, Bumpers' S 1126 appears to be more complete and has the inside track over the Rahall bill. Bumpers' bill includes provisions for royalties, bonding and reclamation. The Rahall bill is criticized by opponents of the Mining Law for its failure to include a royalty provision and for not having specific bonding and reclamation provisions.

Jan 1, 1991

By Y. Luo

Although considerable progress has been made in the last decade in predicting surface subsidence over longwall panels, a number of important issues deserve further studies in order to improve the techniques and accuracy of subsidence predictions. Some of the problems are: (1) subsidence over the chain pillars between mined longwall panels; (2) subsidence development process after face stop due to either a vacation or the completion of a longwall panel; and (3) subsidence initiation and development process over the setup entry area in the initial stage of mining a longwall panel. In this paper, the measured data related to the targeted problems are presented, the data analysis techniques are briefly introduced, and some of the prediction methods developed based on the collected data are proposed. The proposed methods can be used as supplemental tools for the existing subsidence prediction models to improve their prediction accuracy.

Jan 1, 1991

By C. P. Lazzara, F. J. Perzak, C. C. Hwang, C. D. Litton

Fire development and spread along conveyor belts in ventilated ducts were investigated experimentally and theoretically. Various types of conveyor belts used in mining applications were ignited and burned in a full-scale gallery under various flow conditions. The flame spread rates depended strongly on the ventilation air speed. The time-temperature traces of gas and belt obtained at 12 feet from the entrance show that a rapid belt surface temperature change takes place prior to a change in the gas temperature, indicating that radiative heat transfer from the flame to the belt surface plays an important role. Further, anomalies in the flame spread rate in the vicinity of 1.5 m/s air speed (i.e., much greater rate than that observed at either higher or lower speeds) can be explained through the mechanism of flame tilt and the resultant view factor between the flame surface and the belt surface. In order to correlate the fire spread with material properties of the conveyor belts (such as the specific heat, the thermal conductivity, and the pyrolysis temperature) and the fire environment (such as the gas temperature and the ventilation air speed), a theoretical model has been developed. This model is based on the experimental observation that the radiative heat transfer is the dominant mode of energy transfer ahead of the flame front. Agreement between the theory and the experimental results is good.

Jan 1, 1991