Search Documents

By Ahmed I. A. Salama

The problem of estimating separation characteristics by utilizing mass distributions of feed and products is considered. The separation characteristics include mass yield and partition curve. The cases of mass balance and partition functions balance are identified. The developed techniques can handle the cases of two- and three-product separation. Actual data are utilized to demonstrate the proposed techniques.

Jan 1, 1992

By Michael J. Friedel

As part of a study aimed at understanding the hydrology of in situ leach mining (ISLM), the Bureau of Mines, in cooperation with the Cyprus Casa Grande Corporation and the University of Arizona, is investigating dynamic transmissivity conditions during ISLM of a copper oxide ore deposit. Spatial and temporal variations in ore zone transmissivity during two years of ISLM operations at the Cyprus Casa Grande mine are evaluated during sixteen intervals of steady-state injection and recovery well operation. Direct inversion of an analytical hydrologic model is used to obtain estimates of transmissivity at 58 well locations during these intervals. Univariate statistical and geostatistical methods are used to describe the temporal and/or spatial relationships that exist between transmissivity and other ISLM parameters, including average well injection pressure, average sulfuric acid concentration in leach solution, and the relative configuration of injection and recovery wells. Average transmissivity during the sixteen steady-state time intervals varies between 6.00 x 10-6 m2/min. (6.46 x 10-5 ft2/min.) and 3.61 x 10-8 m2/ min. (3.89 x 10-7 ft2/min.). A trend toward decreas¬ing transmissivity is evident during two year of ISLM operations. This decreasing trend is found to correlate with a decreasing sulfuric acid concentration in injected leach solution, and suggests increasing geochemical precipitation within the deposit. Geostatistical analyses reveal a dynamic and anisotropic transmissivity structure within the target ore zone, that is dependent upon spatial and temporal changes in injection pressure and well configuration.

Jan 1, 1992

By Mortimer J. Richardson

In the context of this session on "Practical Placer Mining," a projection of the present into the future first assumes that there is a future for Placers. The second assumption is that there is the combination of adequate reserves and a willing, mining investment source to finance placers. This paper will point out the opportunities on both assumptions, illustrating my positive position on the future of gold placers. In order to focus this paper more effectively, I have chosen GOLD as the subject mineral. However, it is recognized that much of the technology for exploring and mining gold placers has been applied to other alluvial deposits; including platinum, diamond, tin, and various industrial minerals (which are often referred to as "placers" though this contradicts historical definitions). Over the past 10 years I have presented several papers on the general subject of placers, most of which are listed under References. These have included topics such as exploration, evaluation, small-scale gold placer mining and decision-making, mining and processing equipment designs, and dredge-mining operations. In an attempt to identify the more promising, undeveloped placer potentials in the world I have usually mentioned the USSR and China but qualified them as being either inaccessible, or, politically difficult to obtain. However, with recent developments in the USSR, the obstacles appear to be somewhat diminished.

Jan 1, 1992

By Sangwhui Cho

In comminution processes including crushing, grinding and pulverizing, the efficiency of the comminution system is very low. Since the early 1980s, research has been conducted to increase the efficiency of pulverizing mills. Additionally, the application of microprocessors and Personal Computers to process control have come into general use. Given appropriate models of the process and control algorithms, these systems can economically control comminution processes. The ring-roller type mineral pulverizer is known as an energy saving mill. In this study, a control strategy to increase the efficiency of this type mill is explained.

Jan 1, 1992

By Bryan A. Bartley

About 1,000 machines around the world are breaking rock and hard abrasive materials by a very economic, high intensity, autogenous process, but this method is largely ignored by the mining industry. This vertical shaft autogenous impact crusher has impact velocities around 70 m/s, which compare with those of Cascade and SAG mills of up to 10 m/s. The autogenous impact, breakage processes are all at higher intensity levels and the products reflect this difference. The topic of liberation is breifly considered. A series of tests with a laboratory scale machine are reported to illustrate a number of the characteristics of the process. This paper highlights topics for further evaluation and research.

Jan 1, 1992

By S. M. Khandrika

Most of the coal presently used by the utility industry is cleaned at preparation plants employing wet processes. While water is the mainstay of coal washing, it is one of the least desirable components in the final product causing a reduction of the heating value as well as handling difficulties. Currently available dewatering techniques are inefficient for dewatering very fine coal (minus 325 mesh). The US coal industry has expressed serious concern about utilizing advanced cleaning processes such as column flotation because an efficient and economical dewatering process is not available.

Jan 1, 1992

By Richard R. Klimpel

This paper discusses the use of froth flotation as a means of removing metal containing species from a variety of feed streams that generally fall into the classification of waste streams. The variability in solid composition, degree of oxidation, water chemistry, and levels of organic/inorganic contaminants associated with waste streams implies that the collector chemicals used in any flotation process must be much more selective than typically required in normal mineral ore flotation systems. Several examples of such work currently underway will be illustrated showing the potential of flotation to upgrade metal-containing waste streams.

Jan 1, 1992

By O. C. Carter, B. J. Scheiner

The Bureau of Mines is investigating the effects of rainfall and gypsum/cooling pond water on the rate of metal and nonmetal ion mobility through phosphogypsum stacks located in central Florida. Since leachate contains metal and nonmetal ions that have the potential for migration into surface and groundwater, laboratory column leach tests were conducted. Synthetic rainwater was passed through the column and metal and nonmetal ion migration was monitored. Similar experiments were conducted using a number of synthetic solutions which simulated a number of different compositions of gypsum/cooling pond water. Results indicate that within the first five pore volumes most of the mobile metals and nonmetals were removed.

Jan 1, 1992

By J. Alton Burks, Roy C. Bartholomae

The chain conveyor is utilized extensively in underground mining to convey raw ore, especially coal. It is estimated that several thousand loading and continuous mining machines rely on this type of conveyance. Although the chain conveyor is both efficient and highly reliable, its use is generally associated with the production of noise levels that often exceed 105 dBA at the operator's position. Thus, it is one of the most significant contributors to the occupational noise problem experienced by miners in the underground coal mining environment. Conventional engineering noise controls that result in an average reduction of 4 dBA have been previously designed and implemented. However, a novel solution involving a change in conveyor operation has been proposed that takes advantage of two aspects of conveyor noise: 1) conveyor noise has an approximately cubic dependence on conveyor chain speed and 2) due to the damping provided by coal, a full conveyor is 5 dBA quieter than an empty one. An engineering analysis has shown that a significant reduction in the operating noise level of a typical continuous miner can be achieved through the use of an adjustable speed drive automatically controlled by a coal loading sensor that maintains a full conveyor at all times. The potential reduction depends primarily on the mining conditions (coal seam thickness and the presence of either rock or water) and varies from 7-18 dBA. Other benefits to be derived from the use of a variable speed drive include reductions in power consumption, dust, and maintenance costs.

Jan 1, 1992

By Ian H. Clark

A series of numerical experiments were performed in order to elucidate the stress distribution, fracture strength and mineral liberation potential in single specimens of rock during crushing. Fracture strength was shown to reduce under eccentric loading conditions. Similarly, the presence of inclusions, both hard and soft, reduced the fracture strength. The predicted crack paths indicate that mineral liberation is unlikely to be preferential.

Jan 1, 1992

By R. R. Klimpel

Introduction The grinding of coal-water slurries has received increasing industrial attention during the last decade. In particular, there is long-term interest in the use of pulverized coal-water slurries to replace oil in combustion equipment and in the development of coal gasification/liquefaction processes that require coal-water slurries as feed. More specifically, the use of coal-water slurries in gasification requires grinding a high-density slurry containing the smallest amount of water consistent with slurry pumping and spraying. As part of a fundamental engineering research support program aimed at the industrial implementation of dense coal-water slurry grinding, this author has published several papers on how specific rates of breakage vary as a function of slurry rheology (Klimpel, 1982,1982/83). These papers demonstrated that there is a consistent pattern of change in specific rates of breakage of coal in dense slurries with controlled variation in slurry rheology. By matching rheological data with laboratory grinding results, it was possible to identify directly slurry conditions that correspond to: 1) slowing down of breakage rates, 2) the occasional acceleration of breakage of some sizes, and 3) conditions where chemical additives will increase rates of breakage. In brief, these conditions were analyzed using two different criteria: a) the net production rate of material less than some specified size (e.g. kg/min of minus 325 mesh) in a standard batch laboratory mill test as a function of controlled changes in grinding conditions, and b) the use of the one-size-fraction feed method, which consists of following the disappearance of this largest size over grinding time in a batch laboratory mill to arrive at well-known specific rates of breakage (Austin et al., 1984). Detailed references to the methodology used as well as the conclusions are available (Klimpel, 1982, 1982/83) and will not be repeated here. The purpose of this paper is to further demonstrate several additional characteristics of dense coal-water slurry grinding that were shown in a simplified sense in the earlier publications of the author but which have clearly demonstrated themselves as being very important in the industrial simulation and scale-up of such coal-water grinding systems. In particular, this includes the clear and unambiguous demonstration of how the simultaneous acceleration of breakage of some size fractions and slowing down of the breakage of other size fractions is occurring as a function of changes in coal-water slurry density. In the earlier publications (e.g. Klimpel, 1982), it was shown by specially designed experiments that the addition of fine material and/or the use of a chemical thickening agent accelerated the specific rates of breakage of coals of coarser size fractions using the one-size-fraction method. There were also numerous examples given of non first-order breakage (the slowing down of coal breakage rates) using also the one-size-fraction method due to the presence of excessive amounts of fines which corresponded to the development of a rheological yield value. The problem with the simulation and scale-up of any laboratory and/or pilot-scale mill data to an industrial scale using the mechanistic modelling approach involving specific rates of breakage and breakage distribution parameters (e.g. Austin et al., 1984) is the number of assumptions involved in translating the smaller mill breakage parameters to the predicted larger mill breakage parameters. It is apparent, at least to this author, that to accurately simulate and predict larger scale equipment performance from smaller scale data (given that the larger scale data performance is known and hence predictions can be thoroughly checked) requires a better knowledge of breakage parameters than is currently available. More specifically, it was felt that one of the chief problems was the inability of the one-size-fraction method of determining breakage parameters to sufficiently represent the actual magnitude and sometimes even the directions of. the complicated interactions involved with slurry density changes in coal-water slurry grinding. Thus, a special set of experiments was conducted in a somewhat larger batch ball mill (0.457 m diam x 0.610 m length) than the 0.203-m-diam mill used in the original rheology characterization paper (Klimpel, 1982) so as to minimize any unusual effects due to wall-ball interactions (2.54-cm-diam balls used in both mills). More importantly, the measurements of specific rates of breakage were done using a proprietary tracer method on a portion of a given size fraction, which was then remixed into a natural feed size distribution before grinding. The experimental procedure and analysis of subsequent data was done in exactly the same manner as the radioactive tracer technique on coals as originally developed by Gardner (1962). The advantage of such an approach is that it makes no assumptions such as the independence of the specific rate of breakage of any size on the absolute sizes and amounts of other sizes present (both larger and smaller) in the mix of natural feed material. It will be shown that the measured rates of breakage using the direct tracer technique and the one-size fraction method on the same coal are indeed different. In fact, an accurate assessment of what is happening to the rates of breakage as a function of changing slurry density can only he made by measuring particle breakage under grinding conditions approximating the size distributions actually being produced in practice. Experiment procedures and results The pilot mill used was 44 cm diam x 60 cm long with a volume of 91,250 cm3 and was fitted with six 0.5-in. lifter bars.

Jan 1, 1992

By James Wm. White

Mine management now recognizes the value of computer-based truck-shovel dispatching in open pit mines. The key tangible benefits are substantial productivity increases with a given fleet of equipment or, alternately, significant reductions in equipment required to meet production quotas. In this work, we review the literature, report on efficient, optimal algorithms for haul truck dispatching in real-time, and briefly discuss methods used by various mines to evaluate productivity improvements over manual methods. We also present actual results obtained at thirteen mining operations around the world.

Jan 1, 1992

By Natarajan K. A.

During sulphide ore grinding, electrochemical interactions between grinding medium and the minerals play a significant role in bringing out enhanced ball wear on the one hand and alter the surface property of the ground minerals on the other. The role of the flotation reagents added simultaneously during grinding with respect to ball wear as well as flotation is yet to be established. Electrochemical measurements such as rest potential, combination potential and galvanic current between sulphide mineral and ball material couples have been carried out in the presence and absence of flotation reagents to understand the nature of electrochemical interactions between ball material and sulphide mineral. Electrochemical mechanisms and models have been proposed to explain the role played by the flotation reagents during different binary, ternary and quaternary interactions with respect to ball wear during grinding.

Jan 1, 1992

By D. Shink

A small scale continuous flotation cell was designed and constructed at Noranda Technology Centre to develop a mobile testing flotation circuit located next to the production circuit. This mobile small scale flotation pilot plant can easily and economically be set up at any circuit in a mill and used to evaluate and predict plant performance against a given flotation condition. The main feature of the cell, beside the provisions of automatic pulp level and feed rate control, is to provide a reduced surface to volume ratio approaching to that of an industrial machine. This paper describes the basic design and the results of various testwork carried out to date including aeration, conditioning, reagents, recirculation, flotation gas, etc. are presented in comparison with the plant production results.

Jan 1, 1992

By M. Z. Rashad

The purpose of this work is to determine the influence of sample length or size on the value of variance (Semivariogram) to select the suitable length that is required to the geostatistical computations of ore evaluation. Three cases in Ghorabi Iron Ore were studied. The first one was on the iron fraction (Fe%) at which the semivariogram gave an evidence to good continuity of the fraction in the ore. In this case, the length of sample has not important influence. The second case was for the Mn% component of the same area where the semivariogram has a nugget effect. The selected length for this case was 4 meters. The Cl% fraction of the ore was the third case where the anisotropic phenomena was appeared and the suitable length is 3 meters.

Jan 1, 1992

By Stephen Davies

Mining at Hudson Bay Mining & Smelting's Snow Lake Division is now in the mature stage of the mines' lives. These base metal copper-zinc mines have been operating for more than 30 years. Stopes had small pillars called "crown pillars" left between them. These pillars range up to 100 m (330 ft) long by 40 m (130 ft) wide and 15 m (50 ft) thick. Hudson Bay have been successful in removing these pillars by using cable slings, electric scoops, longhole mining and diesel load-haul-dump equipment. The different shapes and sizes of these pillars has required that many innovative techniques be tried in order to find acceptable economic mining methods. An overview of the different methods will be outlined. Background Hudson Bay Mining & Smelting's Snow Lake Division is located in Manitoba some 800 km (500 miles) north of Winnipeg and 200 km (125 miles) by road from the Hudson Bay smelter complex located in Flin Flon, Manitoba (Fig. I). There are currently three producing underground mines and one open pit operating at the Snow Lake Division, producing copper and zinc concentrates. Pillar recovery is intensive and vital to continued production of these mature mines. The crown pillars are producing more than 50% of the current mine production. This figure will increase in the future. The two mines at which crown pillar recovery is taking place and that will be discussed are the 400 t/d (440 stpd) Rod Mine and the 1000 t/d (1100 stpd) Stall Lake Mine, both five-day-a-week producers. Crown pillar mining has been applied for some time at these mines. However, it was only recently that the crown pillars became vital to production. This has necessitated a number of innovative techniques to recover them.

Jan 1, 1992

By R. Gilliam

The Jewett Mine is located in two East Central Texas Counties, Leon County and Freestone County. The area is primarily suited for agriculture with approximately 90% of its agricultural income coming from beef cattle and hogs. In addition to livestock both of these counties produce hay, oats for grazing, pecans and corn. There are 1,101 farms and/or ranches in Freestone County consisting of 381,248 acres. Less than 15% of this acreage is harvested croplands. Leon County has 1,227 farms and/or ranches for a total of 442,387 acres, of which less than 13% is harvested cropland. Total annual agricultural sales for Leon County are approximately $36 million and Freestone County has approximately $21 million. Ninety percent of the annual agricultural sales derive from livestock.

Jan 1, 1992

By Michael J. Shulman

The DEAREX knowledge acquisition and engineering system is a teaching and exploration tool designed to facilitate the under- standing and development of expert systems by explorationists without the aid of a knowledge engineer and without recourse to expert system languages. To fulfill its objective, the DEAREX system considers the selection of exploration methods in desert areas. The system consists of three parts: 1. A tutorial which introduces the basic and selected advanced concepts of expert systems, 2. A sample program illustrating how an expert system works and can be used, and, most importantly, 3. A knowledge acqusition and engineering program which enables users to develop their own expert systems. The tutorial provides a brief and concise introduction to expert systems, a 10 rule exploration example which defines, explains and illustrates the basic concepts and design of expert systems, and a glossary of expert system terms including cross references. The sample program is a larger, self contained example of an expert system with some commentary illustrating addition- al expert system concepts and the role of the knowledge engineer in particularizing rules and ascertaining the knowledge base. Restricting itself to the selection of exploration methods in desert areas, the knowledge acquisition and engineering program questions the user and converts the answers into an expert system. Questions pertain to geology, infrastructure, availability of instrumentation, personnel, etc. Additional information may also included. In conclusion, some salient points concerning knowledge engineering toolkits, shells and knowledge acquisition capabilities such as contained in DEAREX are discussed.

Jan 1, 1992

By A. W. Khair, S. S. Peng

Background The mine is located in Ebensburg, Cambria County, PA. Cambria County is located within the Allegheny Mountain section of the Appalachian Plateau Province. The geologic structures in the mine area included folds, faults, joints and cleats in the coal. These geologic structures seem to have genetic relationships with the Allegheny Front (lannacchione and Puglio, 1979). The mine's geologic structures have been influenced mainly by Ebensburg Anticline and Wilmore Syncline (Watson, 1979). Current longwall panels lay along the western limb of the Wilmore Syncline oriented south 30° west. Surface topographic relief in the area is less than 152 m (500 ft) and overburden thickness varies from 183 to 244 m (600 ft to 800 ft). The coal seam in the mine is part of the Lower Kittanning Formation. The thickness of the B-seam is the subject of discussion. It varies from 1.2 to 1.5 m (48 to 60 in.) and consists of two parts. The lower part is 1.1 to 1.2 m (44 to 48 in.) of soft coal and the remainder is bony coal. The coal seam dips slightly from 0° to 6° to the east-south direction. Panel entries are driven 61 m (200 ft) wide, consisting of three 5.5 m (18 ft) wide entries and two pillars 24.4 x 30.5 m (80 x 100 ft) centers. The mine has a history of cutter roof problems in the entries (Fig. 1) that has delayed the advance rate of entry development considerably and the cost of maintaining those entries is very high due to the requirement of very heavy artificial supports (Fig. 2). Due to excessive convergence in the headgate, installation of additional support and often resetting of steel beam, to provide enough clearance, in these entries imposed additional delay during the retreat of the longwall face, as the shearer cuts coal adjacent to the headgate and shield support at the headgate needs to advance under the steel beams (Fig. 3). Methodology Extensive underground observation indicated that roof cutter [ ]

Jan 1, 1992

By J. W. Leonard

A mine's productivity can be significantly increased by using physical and chemical methods to increase the bulk density of newly mined coal. Increases in coal bulk density allows greater amounts of coal to be placed in ships, barges, railroad cars, trucks, shuttle cars and scoops. Increased bulk density can help increase productivity by increasing throughput of container-based, materials-handling systems. Small, easy-to-achieve changes in mining operations are required to obtain the increased productivity. This article deals with chemical methods used to increase coal bulk density. The results and discussion are based on experiments performed in the laboratory. Research at the University of Kentucky using a chemical method shows that an increase of about 15% in bulk density can be achieved using typically small quantities of commercial reagents. This increase in bulk density can produce a proportional increase in the productivity of a mine.

Jan 1, 1992